1 files changed, 0 insertions, 88 deletions
diff --git a/Documentation/devicetree/bindings/regulator/slg51000.txt b/Documentation/devicetree/bindings/regulator/slg51000.txt
deleted file mode 100644
index aa0733e49b90..000000000000
--- a/Documentation/devicetree/bindings/regulator/slg51000.txt
+++ /dev/null
@@ -1,88 +0,0 @@
-* Dialog Semiconductor SLG51000 Voltage Regulator
-
-Required properties:
-- compatible : Should be "dlg,slg51000" for SLG51000
-- reg : Specifies the I2C slave address.
-- xxx-supply: Input voltage supply regulator for ldo3 to ldo7.
-  These entries are required if regulators are enabled for a device.
-  An absence of these properties can cause the regulator registration to fail.
-  If some of input supply is powered through battery or always-on supply then
-  also it is required to have these parameters with proper node handle of always
-  on power supply.
-    vin3-supply: Input supply for ldo3
-    vin4-supply: Input supply for ldo4
-    vin5-supply: Input supply for ldo5
-    vin6-supply: Input supply for ldo6
-    vin7-supply: Input supply for ldo7
-
-Optional properties:
-- interrupt-parent : Specifies the reference to the interrupt controller.
-- interrupts : IRQ line information.
-- dlg,cs-gpios : Specify a valid GPIO for chip select
-
-Sub-nodes:
-- regulators : This node defines the settings for the regulators.
-  The content of the sub-node is defined by the standard binding
-  for regulators; see regulator.txt.
-
-  The SLG51000 regulators are bound using their names listed below:
-    ldo1
-    ldo2
-    ldo3
-    ldo4
-    ldo5
-    ldo6
-    ldo7
-
-Optional properties for regulators:
-- enable-gpios : Specify a valid GPIO for platform control of the regulator.
-
-Example:
-	pmic: slg51000@75 {
-		compatible = "dlg,slg51000";
-		reg = <0x75>;
-
-		regulators {
-			ldo1 {
-			        regulator-name = "ldo1";
-			        regulator-min-microvolt = <2400000>;
-			        regulator-max-microvolt = <3300000>;
-			};
-
-			ldo2 {
-			        regulator-name = "ldo2";
-			        regulator-min-microvolt = <2400000>;
-			        regulator-max-microvolt = <3300000>;
-			};
-
-			ldo3 {
-			        regulator-name = "ldo3";
-			        regulator-min-microvolt = <1200000>;
-			        regulator-max-microvolt = <3750000>;
-			};
-
-			ldo4 {
-			        regulator-name = "ldo4";
-			        regulator-min-microvolt = <1200000>;
-			        regulator-max-microvolt = <3750000>;
-			};
-
-			ldo5 {
-			        regulator-name = "ldo5";
-			        regulator-min-microvolt = <500000>;
-			        regulator-max-microvolt = <1200000>;
-			};
-
-			ldo6 {
-			        regulator-name = "ldo6";
-			        regulator-min-microvolt = <500000>;
-			        regulator-max-microvolt = <1200000>;
-			};
-
-			ldo7 {
-			        regulator-name = "ldo7";
-			        regulator-min-microvolt = <1200000>;
-			        regulator-max-microvolt = <3750000>;
-			};
-		};
-	};