diff options
| -rw-r--r-- | Documentation/devicetree/bindings/net/xilinx_axienet.txt | 55 | ||||
| -rw-r--r-- | drivers/net/ethernet/xilinx/xilinx_axienet.h | 4 | ||||
| -rw-r--r-- | drivers/net/ethernet/xilinx/xilinx_axienet_main.c | 48 |
3 files changed, 93 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt new file mode 100644 index 000000000000..38f9ec076743 --- /dev/null +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -0,0 +1,55 @@ +XILINX AXI ETHERNET Device Tree Bindings +-------------------------------------------------------- + +Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core +provides connectivity to an external ethernet PHY supporting different +interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two +segments of memory for buffering TX and RX, as well as the capability of +offloading TX/RX checksum calculation off the processor. + +Management configuration is done through the AXI interface, while payload is +sent and received through means of an AXI DMA controller. This driver +includes the DMA driver code, so this driver is incompatible with AXI DMA +driver. + +For more details about mdio please refer phy.txt file in the same directory. + +Required properties: +- compatible : Must be one of "xlnx,axi-ethernet-1.00.a", + "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" +- reg : Address and length of the IO space. +- interrupts : Should be a list of two interrupt, TX and RX. +- phy-handle : Should point to the external phy device. + See ethernet.txt file in the same directory. +- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware + +Optional properties: +- phy-mode : See ethernet.txt +- xlnx,phy-type : Deprecated, do not use, but still accepted in preference + to phy-mode. +- xlnx,txcsum : 0 or empty for disabling TX checksum offload, + 1 to enable partial TX checksum offload, + 2 to enable full TX checksum offload +- xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload + +Example: + axi_ethernet_eth: ethernet@40c00000 { + compatible = "xlnx,axi-ethernet-1.00.a"; + device_type = "network"; + interrupt-parent = <µblaze_0_axi_intc>; + interrupts = <2 0>; + phy-mode = "mii"; + reg = <0x40c00000 0x40000>; + xlnx,rxcsum = <0x2>; + xlnx,rxmem = <0x800>; + xlnx,txcsum = <0x2>; + phy-handle = <&phy0>; + axi_ethernetlite_0_mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: phy@0 { + device_type = "ethernet-phy"; + reg = <1>; + }; + }; + }; diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet.h b/drivers/net/ethernet/xilinx/xilinx_axienet.h index af27f7d1cbf3..5ef626331f85 100644 --- a/drivers/net/ethernet/xilinx/xilinx_axienet.h +++ b/drivers/net/ethernet/xilinx/xilinx_axienet.h @@ -389,7 +389,7 @@ struct axidma_bd { * @dma_err_tasklet: Tasklet structure to process Axi DMA errors * @tx_irq: Axidma TX IRQ number * @rx_irq: Axidma RX IRQ number - * @phy_type: Phy type to identify between MII/GMII/RGMII/SGMII/1000 Base-X + * @phy_mode: Phy type to identify between MII/GMII/RGMII/SGMII/1000 Base-X * @options: AxiEthernet option word * @last_link: Phy link state in which the PHY was negotiated earlier * @features: Stores the extended features supported by the axienet hw @@ -432,7 +432,7 @@ struct axienet_local { int tx_irq; int rx_irq; - u32 phy_type; + phy_interface_t phy_mode; u32 options; /* Current options word */ u32 last_link; diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c index 33c595f4691d..e74e1e897864 100644 --- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c +++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c @@ -531,11 +531,11 @@ static void axienet_adjust_link(struct net_device *ndev) link_state = phy->speed | (phy->duplex << 1) | phy->link; if (lp->last_link != link_state) { if ((phy->speed == SPEED_10) || (phy->speed == SPEED_100)) { - if (lp->phy_type == XAE_PHY_TYPE_1000BASE_X) + if (lp->phy_mode == PHY_INTERFACE_MODE_1000BASEX) setspeed = 0; } else { if ((phy->speed == SPEED_1000) && - (lp->phy_type == XAE_PHY_TYPE_MII)) + (lp->phy_mode == PHY_INTERFACE_MODE_MII)) setspeed = 0; } @@ -935,15 +935,8 @@ static int axienet_open(struct net_device *ndev) return ret; if (lp->phy_node) { - if (lp->phy_type == XAE_PHY_TYPE_GMII) { - phydev = of_phy_connect(lp->ndev, lp->phy_node, - axienet_adjust_link, 0, - PHY_INTERFACE_MODE_GMII); - } else if (lp->phy_type == XAE_PHY_TYPE_RGMII_2_0) { - phydev = of_phy_connect(lp->ndev, lp->phy_node, - axienet_adjust_link, 0, - PHY_INTERFACE_MODE_RGMII_ID); - } + phydev = of_phy_connect(lp->ndev, lp->phy_node, + axienet_adjust_link, 0, lp->phy_mode); if (!phydev) dev_err(lp->dev, "of_phy_connect() failed\n"); @@ -1539,7 +1532,38 @@ static int axienet_probe(struct platform_device *pdev) * the device-tree and accordingly set flags. */ of_property_read_u32(pdev->dev.of_node, "xlnx,rxmem", &lp->rxmem); - of_property_read_u32(pdev->dev.of_node, "xlnx,phy-type", &lp->phy_type); + + /* Start with the proprietary, and broken phy_type */ + ret = of_property_read_u32(pdev->dev.of_node, "xlnx,phy-type", &value); + if (!ret) { + netdev_warn(ndev, "Please upgrade your device tree binary blob to use phy-mode"); + switch (value) { + case XAE_PHY_TYPE_MII: + lp->phy_mode = PHY_INTERFACE_MODE_MII; + break; + case XAE_PHY_TYPE_GMII: + lp->phy_mode = PHY_INTERFACE_MODE_GMII; + break; + case XAE_PHY_TYPE_RGMII_2_0: + lp->phy_mode = PHY_INTERFACE_MODE_RGMII_ID; + break; + case XAE_PHY_TYPE_SGMII: + lp->phy_mode = PHY_INTERFACE_MODE_SGMII; + break; + case XAE_PHY_TYPE_1000BASE_X: + lp->phy_mode = PHY_INTERFACE_MODE_1000BASEX; + break; + default: + ret = -EINVAL; + goto free_netdev; + } + } else { + lp->phy_mode = of_get_phy_mode(pdev->dev.of_node); + if (lp->phy_mode < 0) { + ret = -EINVAL; + goto free_netdev; + } + } /* Find the DMA node, map the DMA registers, and decode the DMA IRQs */ np = of_parse_phandle(pdev->dev.of_node, "axistream-connected", 0); |