diff options
| -rw-r--r-- | arch/mips/include/asm/mach-rc32434/gpio.h | 3 | ||||
| -rw-r--r-- | arch/mips/rb532/devices.c | 19 | ||||
| -rw-r--r-- | drivers/input/misc/Kconfig | 12 | ||||
| -rw-r--r-- | drivers/input/misc/Makefile | 1 | ||||
| -rw-r--r-- | drivers/input/misc/rb532_button.c | 120 |
5 files changed, 137 insertions, 18 deletions
diff --git a/arch/mips/include/asm/mach-rc32434/gpio.h b/arch/mips/include/asm/mach-rc32434/gpio.h index 3cb50d17b62d..12ee8d510160 100644 --- a/arch/mips/include/asm/mach-rc32434/gpio.h +++ b/arch/mips/include/asm/mach-rc32434/gpio.h @@ -80,6 +80,9 @@ struct rb532_gpio_reg { /* Compact Flash GPIO pin */ #define CF_GPIO_NUM 13 +/* S1 button GPIO (shared with UART0_SIN) */ +#define GPIO_BTN_S1 1 + extern void rb532_gpio_set_ilevel(int bit, unsigned gpio); extern void rb532_gpio_set_istat(int bit, unsigned gpio); extern void rb532_gpio_set_func(unsigned gpio); diff --git a/arch/mips/rb532/devices.c b/arch/mips/rb532/devices.c index 4a5f05b662ae..9f40e1ff9b4f 100644 --- a/arch/mips/rb532/devices.c +++ b/arch/mips/rb532/devices.c @@ -200,26 +200,9 @@ static struct platform_device rb532_led = { .id = -1, }; -static struct gpio_keys_button rb532_gpio_btn[] = { - { - .gpio = 1, - .code = BTN_0, - .desc = "S1", - .active_low = 1, - } -}; - -static struct gpio_keys_platform_data rb532_gpio_btn_data = { - .buttons = rb532_gpio_btn, - .nbuttons = ARRAY_SIZE(rb532_gpio_btn), -}; - static struct platform_device rb532_button = { - .name = "gpio-keys", + .name = "rb532-button", .id = -1, - .dev = { - .platform_data = &rb532_gpio_btn_data, - } }; static struct resource rb532_wdt_res[] = { diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index 806d2e66d249..203abac1e23e 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -238,4 +238,16 @@ config INPUT_GPIO_ROTARY_ENCODER To compile this driver as a module, choose M here: the module will be called rotary_encoder. +config INPUT_RB532_BUTTON + tristate "Mikrotik Routerboard 532 button interface" + depends on MIKROTIK_RB532 + depends on GPIOLIB && GENERIC_GPIO + select INPUT_POLLDEV + help + Say Y here if you want support for the S1 button built into + Mikrotik's Routerboard 532. + + To compile this driver as a module, choose M here: the + module will be called rb532_button. + endif diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile index e86cee66c914..e94cfd9be6cc 100644 --- a/drivers/input/misc/Makefile +++ b/drivers/input/misc/Makefile @@ -23,4 +23,5 @@ obj-$(CONFIG_INPUT_APANEL) += apanel.o obj-$(CONFIG_INPUT_SGI_BTNS) += sgi_btns.o obj-$(CONFIG_INPUT_PCF50633_PMU) += pcf50633-input.o obj-$(CONFIG_INPUT_GPIO_ROTARY_ENCODER) += rotary_encoder.o +obj-$(CONFIG_INPUT_RB532_BUTTON) += rb532_button.o diff --git a/drivers/input/misc/rb532_button.c b/drivers/input/misc/rb532_button.c new file mode 100644 index 000000000000..e2c7f622a0b5 --- /dev/null +++ b/drivers/input/misc/rb532_button.c @@ -0,0 +1,120 @@ +/* + * Support for the S1 button on Routerboard 532 + * + * Copyright (C) 2009 Phil Sutter <n0-1@freewrt.org> + */ + +#include <linux/input-polldev.h> +#include <linux/module.h> +#include <linux/platform_device.h> + +#include <asm/mach-rc32434/gpio.h> +#include <asm/mach-rc32434/rb.h> + +#define DRV_NAME "rb532-button" + +#define RB532_BTN_RATE 100 /* msec */ +#define RB532_BTN_KSYM BTN_0 + +/* The S1 button state is provided by GPIO pin 1. But as this + * pin is also used for uart input as alternate function, the + * operational modes must be switched first: + * 1) disable uart using set_latch_u5() + * 2) turn off alternate function implicitly through + * gpio_direction_input() + * 3) read the GPIO's current value + * 4) undo step 2 by enabling alternate function (in this + * mode the GPIO direction is fixed, so no change needed) + * 5) turn on uart again + * The GPIO value occurs to be inverted, so pin high means + * button is not pressed. + */ +static bool rb532_button_pressed(void) +{ + int val; + + set_latch_u5(0, LO_FOFF); + gpio_direction_input(GPIO_BTN_S1); + + val = gpio_get_value(GPIO_BTN_S1); + + rb532_gpio_set_func(GPIO_BTN_S1); + set_latch_u5(LO_FOFF, 0); + + return !val; +} + +static void rb532_button_poll(struct input_polled_dev *poll_dev) +{ + input_report_key(poll_dev->input, RB532_BTN_KSYM, + rb532_button_pressed()); + input_sync(poll_dev->input); +} + +static int __devinit rb532_button_probe(struct platform_device *pdev) +{ + struct input_polled_dev *poll_dev; + int error; + + poll_dev = input_allocate_polled_device(); + if (!poll_dev) + return -ENOMEM; + + poll_dev->poll = rb532_button_poll; + poll_dev->poll_interval = RB532_BTN_RATE; + + poll_dev->input->name = "rb532 button"; + poll_dev->input->phys = "rb532/button0"; + poll_dev->input->id.bustype = BUS_HOST; + poll_dev->input->dev.parent = &pdev->dev; + + dev_set_drvdata(&pdev->dev, poll_dev); + + input_set_capability(poll_dev->input, EV_KEY, RB532_BTN_KSYM); + + error = input_register_polled_device(poll_dev); + if (error) { + input_free_polled_device(poll_dev); + return error; + } + + return 0; +} + +static int __devexit rb532_button_remove(struct platform_device *pdev) +{ + struct input_polled_dev *poll_dev = dev_get_drvdata(&pdev->dev); + + input_unregister_polled_device(poll_dev); + input_free_polled_device(poll_dev); + dev_set_drvdata(&pdev->dev, NULL); + + return 0; +} + +static struct platform_driver rb532_button_driver = { + .probe = rb532_button_probe, + .remove = __devexit_p(rb532_button_remove), + .driver = { + .name = DRV_NAME, + .owner = THIS_MODULE, + }, +}; + +static int __init rb532_button_init(void) +{ + return platform_driver_register(&rb532_button_driver); +} + +static void __exit rb532_button_exit(void) +{ + platform_driver_unregister(&rb532_button_driver); +} + +module_init(rb532_button_init); +module_exit(rb532_button_exit); + +MODULE_AUTHOR("Phil Sutter <n0-1@freewrt.org>"); +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Support for S1 button on Routerboard 532"); +MODULE_ALIAS("platform:" DRV_NAME); |