Move libata to drivers/ata.

1 files changed, 960 insertions, 0 deletions

diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
new file mode 100644
index 000000000000..46c34fd5af8f
--- /dev/null
+++ b/drivers/ata/ata_piix.c
@@ -0,0 +1,960 @@
+/*
+ *    ata_piix.c - Intel PATA/SATA controllers
+ *
+ *    Maintained by:  Jeff Garzik <jgarzik@pobox.com>
+ *    		    Please ALWAYS copy linux-ide@vger.kernel.org
+ *		    on emails.
+ *
+ *
+ *	Copyright 2003-2005 Red Hat Inc
+ *	Copyright 2003-2005 Jeff Garzik
+ *
+ *
+ *	Copyright header from piix.c:
+ *
+ *  Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
+ *  Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ *  Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ *
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ *  libata documentation is available via 'make {ps|pdf}docs',
+ *  as Documentation/DocBook/libata.*
+ *
+ *  Hardware documentation available at http://developer.intel.com/
+ *
+ * Documentation
+ *	Publically available from Intel web site. Errata documentation
+ * is also publically available. As an aide to anyone hacking on this
+ * driver the list of errata that are relevant is below.going back to
+ * PIIX4. Older device documentation is now a bit tricky to find.
+ *
+ * The chipsets all follow very much the same design. The orginal Triton
+ * series chipsets do _not_ support independant device timings, but this
+ * is fixed in Triton II. With the odd mobile exception the chips then
+ * change little except in gaining more modes until SATA arrives. This
+ * driver supports only the chips with independant timing (that is those
+ * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
+ * for the early chip drivers.
+ *
+ * Errata of note:
+ *
+ * Unfixable
+ *	PIIX4    errata #9	- Only on ultra obscure hw
+ *	ICH3	 errata #13     - Not observed to affect real hw
+ *				  by Intel
+ *
+ * Things we must deal with
+ *	PIIX4	errata #10	- BM IDE hang with non UDMA
+ *				  (must stop/start dma to recover)
+ *	440MX   errata #15	- As PIIX4 errata #10
+ *	PIIX4	errata #15	- Must not read control registers
+ * 				  during a PIO transfer
+ *	440MX   errata #13	- As PIIX4 errata #15
+ *	ICH2	errata #21	- DMA mode 0 doesn't work right
+ *	ICH0/1  errata #55	- As ICH2 errata #21
+ *	ICH2	spec c #9	- Extra operations needed to handle
+ *				  drive hotswap [NOT YET SUPPORTED]
+ *	ICH2    spec c #20	- IDE PRD must not cross a 64K boundary
+ *				  and must be dword aligned
+ *	ICH2    spec c #24	- UDMA mode 4,5 t85/86 should be 6ns not 3.3
+ *
+ * Should have been BIOS fixed:
+ *	450NX:	errata #19	- DMA hangs on old 450NX
+ *	450NX:  errata #20	- DMA hangs on old 450NX
+ *	450NX:  errata #25	- Corruption with DMA on old 450NX
+ *	ICH3    errata #15      - IDE deadlock under high load
+ *				  (BIOS must set dev 31 fn 0 bit 23)
+ *	ICH3	errata #18	- Don't use native mode
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME	"ata_piix"
+#define DRV_VERSION	"2.00"
+
+enum {
+	PIIX_IOCFG		= 0x54, /* IDE I/O configuration register */
+	ICH5_PMR		= 0x90, /* port mapping register */
+	ICH5_PCS		= 0x92,	/* port control and status */
+	PIIX_SCC		= 0x0A, /* sub-class code register */
+
+	PIIX_FLAG_IGNORE_PCS	= (1 << 25), /* ignore PCS present bits */
+	PIIX_FLAG_SCR		= (1 << 26), /* SCR available */
+	PIIX_FLAG_AHCI		= (1 << 27), /* AHCI possible */
+	PIIX_FLAG_CHECKINTR	= (1 << 28), /* make sure PCI INTx enabled */
+
+	/* combined mode.  if set, PATA is channel 0.
+	 * if clear, PATA is channel 1.
+	 */
+	PIIX_PORT_ENABLED	= (1 << 0),
+	PIIX_PORT_PRESENT	= (1 << 4),
+
+	PIIX_80C_PRI		= (1 << 5) | (1 << 4),
+	PIIX_80C_SEC		= (1 << 7) | (1 << 6),
+
+	/* controller IDs */
+	piix4_pata		= 0,
+	ich5_pata		= 1,
+	ich5_sata		= 2,
+	esb_sata		= 3,
+	ich6_sata		= 4,
+	ich6_sata_ahci		= 5,
+	ich6m_sata_ahci		= 6,
+	ich8_sata_ahci		= 7,
+
+	/* constants for mapping table */
+	P0			= 0,  /* port 0 */
+	P1			= 1,  /* port 1 */
+	P2			= 2,  /* port 2 */
+	P3			= 3,  /* port 3 */
+	IDE			= -1, /* IDE */
+	NA			= -2, /* not avaliable */
+	RV			= -3, /* reserved */
+
+	PIIX_AHCI_DEVICE	= 6,
+};
+
+struct piix_map_db {
+	const u32 mask;
+	const u16 port_enable;
+	const int present_shift;
+	const int map[][4];
+};
+
+struct piix_host_priv {
+	const int *map;
+	const struct piix_map_db *map_db;
+};
+
+static int piix_init_one (struct pci_dev *pdev,
+				    const struct pci_device_id *ent);
+static void piix_host_stop(struct ata_host_set *host_set);
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+static void piix_pata_error_handler(struct ata_port *ap);
+static void piix_sata_error_handler(struct ata_port *ap);
+
+static unsigned int in_module_init = 1;
+
+static const struct pci_device_id piix_pci_tbl[] = {
+#ifdef ATA_ENABLE_PATA
+	{ 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix4_pata },
+	{ 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+	{ 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+	{ 0x8086, 0x27df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+#endif
+
+	/* NOTE: The following PCI ids must be kept in sync with the
+	 * list in drivers/pci/quirks.c.
+	 */
+
+	/* 82801EB (ICH5) */
+	{ 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+	/* 82801EB (ICH5) */
+	{ 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+	/* 6300ESB (ICH5 variant with broken PCS present bits) */
+	{ 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+	/* 6300ESB pretending RAID */
+	{ 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+	/* 82801FB/FW (ICH6/ICH6W) */
+	{ 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
+	/* 82801FR/FRW (ICH6R/ICH6RW) */
+	{ 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+	/* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented) */
+	{ 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
+	/* 82801GB/GR/GH (ICH7, identical to ICH6) */
+	{ 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+	/* 2801GBM/GHM (ICH7M, identical to ICH6M) */
+	{ 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
+	/* Enterprise Southbridge 2 (where's the datasheet?) */
+	{ 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+	/* SATA Controller 1 IDE (ICH8, no datasheet yet) */
+	{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* SATA Controller 2 IDE (ICH8, ditto) */
+	{ 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* Mobile SATA Controller IDE (ICH8M, ditto) */
+	{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+
+	{ }	/* terminate list */
+};
+
+static struct pci_driver piix_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= piix_pci_tbl,
+	.probe			= piix_init_one,
+	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
+};
+
+static struct scsi_host_template piix_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
+	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
+};
+
+static const struct ata_port_operations piix_pata_ops = {
+	.port_disable		= ata_port_disable,
+	.set_piomode		= piix_set_piomode,
+	.set_dmamode		= piix_set_dmamode,
+	.mode_filter		= ata_pci_default_filter,
+
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.bmdma_setup		= ata_bmdma_setup,
+	.bmdma_start		= ata_bmdma_start,
+	.bmdma_stop		= ata_bmdma_stop,
+	.bmdma_status		= ata_bmdma_status,
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+	.data_xfer		= ata_pio_data_xfer,
+
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= piix_pata_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= ata_bmdma_irq_clear,
+
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= piix_host_stop,
+};
+
+static const struct ata_port_operations piix_sata_ops = {
+	.port_disable		= ata_port_disable,
+
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.bmdma_setup		= ata_bmdma_setup,
+	.bmdma_start		= ata_bmdma_start,
+	.bmdma_stop		= ata_bmdma_stop,
+	.bmdma_status		= ata_bmdma_status,
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+	.data_xfer		= ata_pio_data_xfer,
+
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= piix_sata_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= ata_bmdma_irq_clear,
+
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= piix_host_stop,
+};
+
+static const struct piix_map_db ich5_map_db = {
+	.mask = 0x7,
+	.port_enable = 0x3,
+	.present_shift = 4,
+	.map = {
+		/* PM   PS   SM   SS       MAP  */
+		{  P0,  NA,  P1,  NA }, /* 000b */
+		{  P1,  NA,  P0,  NA }, /* 001b */
+		{  RV,  RV,  RV,  RV },
+		{  RV,  RV,  RV,  RV },
+		{  P0,  P1, IDE, IDE }, /* 100b */
+		{  P1,  P0, IDE, IDE }, /* 101b */
+		{ IDE, IDE,  P0,  P1 }, /* 110b */
+		{ IDE, IDE,  P1,  P0 }, /* 111b */
+	},
+};
+
+static const struct piix_map_db ich6_map_db = {
+	.mask = 0x3,
+	.port_enable = 0xf,
+	.present_shift = 4,
+	.map = {
+		/* PM   PS   SM   SS       MAP */
+		{  P0,  P2,  P1,  P3 }, /* 00b */
+		{ IDE, IDE,  P1,  P3 }, /* 01b */
+		{  P0,  P2, IDE, IDE }, /* 10b */
+		{  RV,  RV,  RV,  RV },
+	},
+};
+
+static const struct piix_map_db ich6m_map_db = {
+	.mask = 0x3,
+	.port_enable = 0x5,
+	.present_shift = 4,
+	.map = {
+		/* PM   PS   SM   SS       MAP */
+		{  P0,  P2,  RV,  RV }, /* 00b */
+		{  RV,  RV,  RV,  RV },
+		{  P0,  P2, IDE, IDE }, /* 10b */
+		{  RV,  RV,  RV,  RV },
+	},
+};
+
+static const struct piix_map_db ich8_map_db = {
+	.mask = 0x3,
+	.port_enable = 0x3,
+	.present_shift = 8,
+	.map = {
+		/* PM   PS   SM   SS       MAP */
+		{  P0,  NA,  P1,  NA }, /* 00b (hardwired) */
+		{  RV,  RV,  RV,  RV },
+		{  RV,  RV,  RV,  RV }, /* 10b (never) */
+		{  RV,  RV,  RV,  RV },
+	},
+};
+
+static const struct piix_map_db *piix_map_db_table[] = {
+	[ich5_sata]		= &ich5_map_db,
+	[esb_sata]		= &ich5_map_db,
+	[ich6_sata]		= &ich6_map_db,
+	[ich6_sata_ahci]	= &ich6_map_db,
+	[ich6m_sata_ahci]	= &ich6m_map_db,
+	[ich8_sata_ahci]	= &ich8_map_db,
+};
+
+static struct ata_port_info piix_port_info[] = {
+	/* piix4_pata */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SLAVE_POSS,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+#if 0
+		.mwdma_mask	= 0x06, /* mwdma1-2 */
+#else
+		.mwdma_mask	= 0x00, /* mwdma broken */
+#endif
+		.udma_mask	= ATA_UDMA_MASK_40C,
+		.port_ops	= &piix_pata_ops,
+	},
+
+	/* ich5_pata */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+#if 0
+		.mwdma_mask	= 0x06, /* mwdma1-2 */
+#else
+		.mwdma_mask	= 0x00, /* mwdma broken */
+#endif
+		.udma_mask	= 0x3f, /* udma0-5 */
+		.port_ops	= &piix_pata_ops,
+	},
+
+	/* ich5_sata */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask	= 0x7f,	/* udma0-6 */
+		.port_ops	= &piix_sata_ops,
+	},
+
+	/* i6300esb_sata */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SATA |
+				  PIIX_FLAG_CHECKINTR | PIIX_FLAG_IGNORE_PCS,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask	= 0x7f,	/* udma0-6 */
+		.port_ops	= &piix_sata_ops,
+	},
+
+	/* ich6_sata */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SATA |
+				  PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask	= 0x7f,	/* udma0-6 */
+		.port_ops	= &piix_sata_ops,
+	},
+
+	/* ich6_sata_ahci */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SATA |
+				  PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+				  PIIX_FLAG_AHCI,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask	= 0x7f,	/* udma0-6 */
+		.port_ops	= &piix_sata_ops,
+	},
+
+	/* ich6m_sata_ahci */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SATA |
+				  PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+				  PIIX_FLAG_AHCI,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask	= 0x7f,	/* udma0-6 */
+		.port_ops	= &piix_sata_ops,
+	},
+
+	/* ich8_sata_ahci */
+	{
+		.sht		= &piix_sht,
+		.host_flags	= ATA_FLAG_SATA |
+				  PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+				  PIIX_FLAG_AHCI,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask	= 0x7f,	/* udma0-6 */
+		.port_ops	= &piix_sata_ops,
+	},
+};
+
+static struct pci_bits piix_enable_bits[] = {
+	{ 0x41U, 1U, 0x80UL, 0x80UL },	/* port 0 */
+	{ 0x43U, 1U, 0x80UL, 0x80UL },	/* port 1 */
+};
+
+MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik");
+MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+/**
+ *	piix_pata_cbl_detect - Probe host controller cable detect info
+ *	@ap: Port for which cable detect info is desired
+ *
+ *	Read 80c cable indicator from ATA PCI device's PCI config
+ *	register.  This register is normally set by firmware (BIOS).
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+static void piix_pata_cbl_detect(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+	u8 tmp, mask;
+
+	/* no 80c support in host controller? */
+	if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0)
+		goto cbl40;
+
+	/* check BIOS cable detect results */
+	mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
+	pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
+	if ((tmp & mask) == 0)
+		goto cbl40;
+
+	ap->cbl = ATA_CBL_PATA80;
+	return;
+
+cbl40:
+	ap->cbl = ATA_CBL_PATA40;
+	ap->udma_mask &= ATA_UDMA_MASK_40C;
+}
+
+/**
+ *	piix_pata_prereset - prereset for PATA host controller
+ *	@ap: Target port
+ *
+ *	Prereset including cable detection.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+static int piix_pata_prereset(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+
+	if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) {
+		ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
+		ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
+		return 0;
+	}
+
+	piix_pata_cbl_detect(ap);
+
+	return ata_std_prereset(ap);
+}
+
+static void piix_pata_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, piix_pata_prereset, ata_std_softreset, NULL,
+			   ata_std_postreset);
+}
+
+/**
+ *	piix_sata_prereset - prereset for SATA host controller
+ *	@ap: Target port
+ *
+ *	Reads and configures SATA PCI device's PCI config register
+ *	Port Configuration and Status (PCS) to determine port and
+ *	device availability.  Return -ENODEV to skip reset if no
+ *	device is present.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ *
+ *	RETURNS:
+ *	0 if device is present, -ENODEV otherwise.
+ */
+static int piix_sata_prereset(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+	struct piix_host_priv *hpriv = ap->host_set->private_data;
+	const unsigned int *map = hpriv->map;
+	int base = 2 * ap->port_no;
+	unsigned int present = 0;
+	int port, i;
+	u16 pcs;
+
+	pci_read_config_word(pdev, ICH5_PCS, &pcs);
+	DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base);
+
+	for (i = 0; i < 2; i++) {
+		port = map[base + i];
+		if (port < 0)
+			continue;
+		if ((ap->flags & PIIX_FLAG_IGNORE_PCS) ||
+		    (pcs & 1 << (hpriv->map_db->present_shift + port)))
+			present = 1;
+	}
+
+	DPRINTK("ata%u: LEAVE, pcs=0x%x present=0x%x\n",
+		ap->id, pcs, present);
+
+	if (!present) {
+		ata_port_printk(ap, KERN_INFO, "SATA port has no device.\n");
+		ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
+		return 0;
+	}
+
+	return ata_std_prereset(ap);
+}
+
+static void piix_sata_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, piix_sata_prereset, ata_std_softreset, NULL,
+			   ata_std_postreset);
+}
+
+/**
+ *	piix_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: um
+ *
+ *	Set PIO mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
+	struct pci_dev *dev	= to_pci_dev(ap->host_set->dev);
+	unsigned int is_slave	= (adev->devno != 0);
+	unsigned int master_port= ap->port_no ? 0x42 : 0x40;
+	unsigned int slave_port	= 0x44;
+	u16 master_data;
+	u8 slave_data;
+
+	static const	 /* ISP  RTC */
+	u8 timings[][2]	= { { 0, 0 },
+			    { 0, 0 },
+			    { 1, 0 },
+			    { 2, 1 },
+			    { 2, 3 }, };
+
+	pci_read_config_word(dev, master_port, &master_data);
+	if (is_slave) {
+		master_data |= 0x4000;
+		/* enable PPE, IE and TIME */
+		master_data |= 0x0070;
+		pci_read_config_byte(dev, slave_port, &slave_data);
+		slave_data &= (ap->port_no ? 0x0f : 0xf0);
+		slave_data |=
+			(timings[pio][0] << 2) |
+			(timings[pio][1] << (ap->port_no ? 4 : 0));
+	} else {
+		master_data &= 0xccf8;
+		/* enable PPE, IE and TIME */
+		master_data |= 0x0007;
+		master_data |=
+			(timings[pio][0] << 12) |
+			(timings[pio][1] << 8);
+	}
+	pci_write_config_word(dev, master_port, master_data);
+	if (is_slave)
+		pci_write_config_byte(dev, slave_port, slave_data);
+}
+
+/**
+ *	piix_set_dmamode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: um
+ *	@udma: udma mode, 0 - 6
+ *
+ *	Set UDMA mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int udma	= adev->dma_mode; /* FIXME: MWDMA too */
+	struct pci_dev *dev	= to_pci_dev(ap->host_set->dev);
+	u8 maslave		= ap->port_no ? 0x42 : 0x40;
+	u8 speed		= udma;
+	unsigned int drive_dn	= (ap->port_no ? 2 : 0) + adev->devno;
+	int a_speed		= 3 << (drive_dn * 4);
+	int u_flag		= 1 << drive_dn;
+	int v_flag		= 0x01 << drive_dn;
+	int w_flag		= 0x10 << drive_dn;
+	int u_speed		= 0;
+	int			sitre;
+	u16			reg4042, reg4a;
+	u8			reg48, reg54, reg55;
+
+	pci_read_config_word(dev, maslave, &reg4042);
+	DPRINTK("reg4042 = 0x%04x\n", reg4042);
+	sitre = (reg4042 & 0x4000) ? 1 : 0;
+	pci_read_config_byte(dev, 0x48, &reg48);
+	pci_read_config_word(dev, 0x4a, &reg4a);
+	pci_read_config_byte(dev, 0x54, &reg54);
+	pci_read_config_byte(dev, 0x55, &reg55);
+
+	switch(speed) {
+		case XFER_UDMA_4:
+		case XFER_UDMA_2:	u_speed = 2 << (drive_dn * 4); break;
+		case XFER_UDMA_6:
+		case XFER_UDMA_5:
+		case XFER_UDMA_3:
+		case XFER_UDMA_1:	u_speed = 1 << (drive_dn * 4); break;
+		case XFER_UDMA_0:	u_speed = 0 << (drive_dn * 4); break;
+		case XFER_MW_DMA_2:
+		case XFER_MW_DMA_1:	break;
+		default:
+			BUG();
+			return;
+	}
+
+	if (speed >= XFER_UDMA_0) {
+		if (!(reg48 & u_flag))
+			pci_write_config_byte(dev, 0x48, reg48 | u_flag);
+		if (speed == XFER_UDMA_5) {
+			pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
+		} else {
+			pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+		}
+		if ((reg4a & a_speed) != u_speed)
+			pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
+		if (speed > XFER_UDMA_2) {
+			if (!(reg54 & v_flag))
+				pci_write_config_byte(dev, 0x54, reg54 | v_flag);
+		} else
+			pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+	} else {
+		if (reg48 & u_flag)
+			pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
+		if (reg4a & a_speed)
+			pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
+		if (reg54 & v_flag)
+			pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+		if (reg55 & w_flag)
+			pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+	}
+}
+
+#define AHCI_PCI_BAR 5
+#define AHCI_GLOBAL_CTL 0x04
+#define AHCI_ENABLE (1 << 31)
+static int piix_disable_ahci(struct pci_dev *pdev)
+{
+	void __iomem *mmio;
+	u32 tmp;
+	int rc = 0;
+
+	/* BUG: pci_enable_device has not yet been called.  This
+	 * works because this device is usually set up by BIOS.
+	 */
+
+	if (!pci_resource_start(pdev, AHCI_PCI_BAR) ||
+	    !pci_resource_len(pdev, AHCI_PCI_BAR))
+		return 0;
+
+	mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64);
+	if (!mmio)
+		return -ENOMEM;
+
+	tmp = readl(mmio + AHCI_GLOBAL_CTL);
+	if (tmp & AHCI_ENABLE) {
+		tmp &= ~AHCI_ENABLE;
+		writel(tmp, mmio + AHCI_GLOBAL_CTL);
+
+		tmp = readl(mmio + AHCI_GLOBAL_CTL);
+		if (tmp & AHCI_ENABLE)
+			rc = -EIO;
+	}
+
+	pci_iounmap(pdev, mmio);
+	return rc;
+}
+
+/**
+ *	piix_check_450nx_errata	-	Check for problem 450NX setup
+ *	@ata_dev: the PCI device to check
+ *
+ *	Check for the present of 450NX errata #19 and errata #25. If
+ *	they are found return an error code so we can turn off DMA
+ */
+
+static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
+{
+	struct pci_dev *pdev = NULL;
+	u16 cfg;
+	u8 rev;
+	int no_piix_dma = 0;
+
+	while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
+	{
+		/* Look for 450NX PXB. Check for problem configurations
+		   A PCI quirk checks bit 6 already */
+		pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+		pci_read_config_word(pdev, 0x41, &cfg);
+		/* Only on the original revision: IDE DMA can hang */
+		if (rev == 0x00)
+			no_piix_dma = 1;
+		/* On all revisions below 5 PXB bus lock must be disabled for IDE */
+		else if (cfg & (1<<14) && rev < 5)
+			no_piix_dma = 2;
+	}
+	if (no_piix_dma)
+		dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n");
+	if (no_piix_dma == 2)
+		dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n");
+	return no_piix_dma;
+}
+
+static void __devinit piix_init_pcs(struct pci_dev *pdev,
+				    const struct piix_map_db *map_db)
+{
+	u16 pcs, new_pcs;
+
+	pci_read_config_word(pdev, ICH5_PCS, &pcs);
+
+	new_pcs = pcs | map_db->port_enable;
+
+	if (new_pcs != pcs) {
+		DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs);
+		pci_write_config_word(pdev, ICH5_PCS, new_pcs);
+		msleep(150);
+	}
+}
+
+static void __devinit piix_init_sata_map(struct pci_dev *pdev,
+					 struct ata_port_info *pinfo,
+					 const struct piix_map_db *map_db)
+{
+	struct piix_host_priv *hpriv = pinfo[0].private_data;
+	const unsigned int *map;
+	int i, invalid_map = 0;
+	u8 map_value;
+
+	pci_read_config_byte(pdev, ICH5_PMR, &map_value);
+
+	map = map_db->map[map_value & map_db->mask];
+
+	dev_printk(KERN_INFO, &pdev->dev, "MAP [");
+	for (i = 0; i < 4; i++) {
+		switch (map[i]) {
+		case RV:
+			invalid_map = 1;
+			printk(" XX");
+			break;
+
+		case NA:
+			printk(" --");
+			break;
+
+		case IDE:
+			WARN_ON((i & 1) || map[i + 1] != IDE);
+			pinfo[i / 2] = piix_port_info[ich5_pata];
+			pinfo[i / 2].private_data = hpriv;
+			i++;
+			printk(" IDE IDE");
+			break;
+
+		default:
+			printk(" P%d", map[i]);
+			if (i & 1)
+				pinfo[i / 2].host_flags |= ATA_FLAG_SLAVE_POSS;
+			break;
+		}
+	}
+	printk(" ]\n");
+
+	if (invalid_map)
+		dev_printk(KERN_ERR, &pdev->dev,
+			   "invalid MAP value %u\n", map_value);
+
+	hpriv->map = map;
+	hpriv->map_db = map_db;
+}
+
+/**
+ *	piix_init_one - Register PIIX ATA PCI device with kernel services
+ *	@pdev: PCI device to register
+ *	@ent: Entry in piix_pci_tbl matching with @pdev
+ *
+ *	Called from kernel PCI layer.  We probe for combined mode (sigh),
+ *	and then hand over control to libata, for it to do the rest.
+ *
+ *	LOCKING:
+ *	Inherited from PCI layer (may sleep).
+ *
+ *	RETURNS:
+ *	Zero on success, or -ERRNO value.
+ */
+
+static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	static int printed_version;
+	struct ata_port_info port_info[2];
+	struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] };
+	struct piix_host_priv *hpriv;
+	unsigned long host_flags;
+
+	if (!printed_version++)
+		dev_printk(KERN_DEBUG, &pdev->dev,
+			   "version " DRV_VERSION "\n");
+
+	/* no hotplugging support (FIXME) */
+	if (!in_module_init)
+		return -ENODEV;
+
+	hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
+	if (!hpriv)
+		return -ENOMEM;
+
+	port_info[0] = piix_port_info[ent->driver_data];
+	port_info[1] = piix_port_info[ent->driver_data];
+	port_info[0].private_data = hpriv;
+	port_info[1].private_data = hpriv;
+
+	host_flags = port_info[0].host_flags;
+
+	if (host_flags & PIIX_FLAG_AHCI) {
+		u8 tmp;
+		pci_read_config_byte(pdev, PIIX_SCC, &tmp);
+		if (tmp == PIIX_AHCI_DEVICE) {
+			int rc = piix_disable_ahci(pdev);
+			if (rc)
+				return rc;
+		}
+	}
+
+	/* Initialize SATA map */
+	if (host_flags & ATA_FLAG_SATA) {
+		piix_init_sata_map(pdev, port_info,
+				   piix_map_db_table[ent->driver_data]);
+		piix_init_pcs(pdev, piix_map_db_table[ent->driver_data]);
+	}
+
+	/* On ICH5, some BIOSen disable the interrupt using the
+	 * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
+	 * On ICH6, this bit has the same effect, but only when
+	 * MSI is disabled (and it is disabled, as we don't use
+	 * message-signalled interrupts currently).
+	 */
+	if (host_flags & PIIX_FLAG_CHECKINTR)
+		pci_intx(pdev, 1);
+
+	if (piix_check_450nx_errata(pdev)) {
+		/* This writes into the master table but it does not
+		   really matter for this errata as we will apply it to
+		   all the PIIX devices on the board */
+		port_info[0].mwdma_mask = 0;
+		port_info[0].udma_mask = 0;
+		port_info[1].mwdma_mask = 0;
+		port_info[1].udma_mask = 0;
+	}
+	return ata_pci_init_one(pdev, ppinfo, 2);
+}
+
+static void piix_host_stop(struct ata_host_set *host_set)
+{
+	ata_host_stop(host_set);
+}
+
+static int __init piix_init(void)
+{
+	int rc;
+
+	DPRINTK("pci_register_driver\n");
+	rc = pci_register_driver(&piix_pci_driver);
+	if (rc)
+		return rc;
+
+	in_module_init = 0;
+
+	DPRINTK("done\n");
+	return 0;
+}
+
+static void __exit piix_exit(void)
+{
+	pci_unregister_driver(&piix_pci_driver);
+}
+
+module_init(piix_init);
+module_exit(piix_exit);
+