[ARM] pxa: move common MFP handling code into plat-pxa

Signed-off-by: Eric Miao <eric.miao@marvell.com>

11 files changed, 32 insertions, 316 deletions

diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h
index a72869b73ee3..b13dc0269a6d 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h
@@ -1,7 +1,6 @@
 #ifndef __ASM_ARCH_MFP_PXA25X_H
 #define __ASM_ARCH_MFP_PXA25X_H
 
-#include <mach/mfp.h>
 #include <mach/mfp-pxa2xx.h>
 
 /* GPIO */
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
index da4f85a4f990..6543c05f47ed 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
@@ -8,7 +8,6 @@
  * specific controller, and this should work in most cases.
  */
 
-#include <mach/mfp.h>
 #include <mach/mfp-pxa2xx.h>
 
 /* Note: GPIO3/GPIO4 will be driven by Power I2C when PCFR/PI2C_EN
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h b/arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h
index 3e9211591e20..658b28ed129b 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h
@@ -1,7 +1,7 @@
 #ifndef __ASM_ARCH_MFP_PXA2XX_H
 #define __ASM_ARCH_MFP_PXA2XX_H
 
-#include <mach/mfp.h>
+#include <plat/mfp.h>
 
 /*
  * the following MFP_xxx bit definitions in mfp.h are re-used for pxa2xx:
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa300.h b/arch/arm/mach-pxa/include/mach/mfp-pxa300.h
index 928fbef9cbf3..ae8441192ef0 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa300.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa300.h
@@ -15,7 +15,6 @@
 #ifndef __ASM_ARCH_MFP_PXA300_H
 #define __ASM_ARCH_MFP_PXA300_H
 
-#include <mach/mfp.h>
 #include <mach/mfp-pxa3xx.h>
 
 /* GPIO */
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa320.h b/arch/arm/mach-pxa/include/mach/mfp-pxa320.h
index 80a0da9e092d..07897e61d05a 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa320.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa320.h
@@ -15,7 +15,6 @@
 #ifndef __ASM_ARCH_MFP_PXA320_H
 #define __ASM_ARCH_MFP_PXA320_H
 
-#include <mach/mfp.h>
 #include <mach/mfp-pxa3xx.h>
 
 /* GPIO */
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h b/arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h
index 1f6b35c015d0..d375195d982b 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h
@@ -1,68 +1,9 @@
 #ifndef __ASM_ARCH_MFP_PXA3XX_H
 #define __ASM_ARCH_MFP_PXA3XX_H
 
-#define MFPR_BASE	(0x40e10000)
-#define MFPR_SIZE	(PAGE_SIZE)
-
-/* MFPR register bit definitions */
-#define MFPR_PULL_SEL		(0x1 << 15)
-#define MFPR_PULLUP_EN		(0x1 << 14)
-#define MFPR_PULLDOWN_EN	(0x1 << 13)
-#define MFPR_SLEEP_SEL		(0x1 << 9)
-#define MFPR_SLEEP_OE_N		(0x1 << 7)
-#define MFPR_EDGE_CLEAR		(0x1 << 6)
-#define MFPR_EDGE_FALL_EN	(0x1 << 5)
-#define MFPR_EDGE_RISE_EN	(0x1 << 4)
-
-#define MFPR_SLEEP_DATA(x)	((x) << 8)
-#define MFPR_DRIVE(x)		(((x) & 0x7) << 10)
-#define MFPR_AF_SEL(x)		(((x) & 0x7) << 0)
+#include <plat/mfp.h>
 
-#define MFPR_EDGE_NONE		(0)
-#define MFPR_EDGE_RISE		(MFPR_EDGE_RISE_EN)
-#define MFPR_EDGE_FALL		(MFPR_EDGE_FALL_EN)
-#define MFPR_EDGE_BOTH		(MFPR_EDGE_RISE | MFPR_EDGE_FALL)
-
-/*
- * Table that determines the low power modes outputs, with actual settings
- * used in parentheses for don't-care values. Except for the float output,
- * the configured driven and pulled levels match, so if there is a need for
- * non-LPM pulled output, the same configuration could probably be used.
- *
- * Output value  sleep_oe_n  sleep_data  pullup_en  pulldown_en  pull_sel
- *                 (bit 7)    (bit 8)    (bit 14)     (bit 13)   (bit 15)
- *
- * Input            0          X(0)        X(0)        X(0)       0
- * Drive 0          0          0           0           X(1)       0
- * Drive 1          0          1           X(1)        0	  0
- * Pull hi (1)      1          X(1)        1           0	  0
- * Pull lo (0)      1          X(0)        0           1	  0
- * Z (float)        1          X(0)        0           0	  0
- */
-#define MFPR_LPM_INPUT		(0)
-#define MFPR_LPM_DRIVE_LOW	(MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN)
-#define MFPR_LPM_DRIVE_HIGH    	(MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN)
-#define MFPR_LPM_PULL_LOW      	(MFPR_LPM_DRIVE_LOW  | MFPR_SLEEP_OE_N)
-#define MFPR_LPM_PULL_HIGH     	(MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N)
-#define MFPR_LPM_FLOAT         	(MFPR_SLEEP_OE_N)
-#define MFPR_LPM_MASK		(0xe080)
-
-/*
- * The pullup and pulldown state of the MFP pin at run mode is by default
- * determined by the selected alternate function. In case that some buggy
- * devices need to override this default behavior,  the definitions below
- * indicates the setting of corresponding MFPR bits
- *
- * Definition       pull_sel  pullup_en  pulldown_en
- * MFPR_PULL_NONE       0         0        0
- * MFPR_PULL_LOW        1         0        1
- * MFPR_PULL_HIGH       1         1        0
- * MFPR_PULL_BOTH       1         1        1
- */
-#define MFPR_PULL_NONE		(0)
-#define MFPR_PULL_LOW		(MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
-#define MFPR_PULL_BOTH		(MFPR_PULL_LOW | MFPR_PULLUP_EN)
-#define MFPR_PULL_HIGH		(MFPR_PULL_SEL | MFPR_PULLUP_EN)
+#define MFPR_BASE	(0x40e10000)
 
 /* PXA3xx common MFP configurations - processor specific ones defined
  * in mfp-pxa300.h and mfp-pxa320.h
@@ -197,56 +138,21 @@
 #define GPIO5_2_GPIO		MFP_CFG(GPIO5_2, AF0)
 #define GPIO6_2_GPIO		MFP_CFG(GPIO6_2, AF0)
 
-/*
- * each MFP pin will have a MFPR register, since the offset of the
- * register varies between processors, the processor specific code
- * should initialize the pin offsets by pxa3xx_mfp_init_addr()
- *
- * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map"
- * structure, which represents a range of MFP pins from "start" to
- * "end", with the offset begining at "offset", to define a single
- * pin, let "end" = -1
- *
- * use
- *
- * MFP_ADDR_X() to define a range of pins
- * MFP_ADDR()   to define a single pin
- * MFP_ADDR_END to signal the end of pin offset definitions
- */
-struct pxa3xx_mfp_addr_map {
-	unsigned int	start;
-	unsigned int	end;
-	unsigned long	offset;
-};
-
-#define MFP_ADDR_X(start, end, offset) \
-	{ MFP_PIN_##start, MFP_PIN_##end, offset }
-
-#define MFP_ADDR(pin, offset) \
-	{ MFP_PIN_##pin, -1, offset }
-
-#define MFP_ADDR_END	{ MFP_PIN_INVALID, 0 }
-
-/*
- * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access
- * to the MFPR register
- */
-unsigned long pxa3xx_mfp_read(int mfp);
-void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val);
-
-/*
- * pxa3xx_mfp_config - configure the MFPR registers
- *
- * used by board specific initialization code
- */
-void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num);
-
-/*
- * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin
- * index and MFPR register offset
- *
- * used by processor specific code
+/* NOTE: usage of these two functions is not recommended,
+ * use pxa3xx_mfp_config() instead.
  */
-void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *);
-void __init pxa3xx_init_mfp(void);
+static inline unsigned long pxa3xx_mfp_read(int mfp)
+{
+	return mfp_read(mfp);
+}
+
+static inline void pxa3xx_mfp_write(int mfp, unsigned long val)
+{
+	mfp_write(mfp, val);
+}
+
+static inline void pxa3xx_mfp_config(unsigned long *mfp_cfg, int num)
+{
+	mfp_config(mfp_cfg, num);
+}
 #endif /* __ASM_ARCH_MFP_PXA3XX_H */
diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa930.h b/arch/arm/mach-pxa/include/mach/mfp-pxa930.h
index fa73f56a1372..0d119d3b9221 100644
--- a/arch/arm/mach-pxa/include/mach/mfp-pxa930.h
+++ b/arch/arm/mach-pxa/include/mach/mfp-pxa930.h
@@ -13,7 +13,6 @@
 #ifndef __ASM_ARCH_MFP_PXA9xx_H
 #define __ASM_ARCH_MFP_PXA9xx_H
 
-#include <mach/mfp.h>
 #include <mach/mfp-pxa3xx.h>
 
 /* GPIO */
diff --git a/arch/arm/mach-pxa/mfp-pxa3xx.c b/arch/arm/mach-pxa/mfp-pxa3xx.c
index eb197a6e8e94..7a270eecd480 100644
--- a/arch/arm/mach-pxa/mfp-pxa3xx.c
+++ b/arch/arm/mach-pxa/mfp-pxa3xx.c
@@ -20,183 +20,9 @@
 #include <linux/sysdev.h>
 
 #include <mach/hardware.h>
-#include <mach/mfp.h>
 #include <mach/mfp-pxa3xx.h>
 #include <mach/pxa3xx-regs.h>
 
-/* mfp_spin_lock is used to ensure that MFP register configuration
- * (most likely a read-modify-write operation) is atomic, and that
- * mfp_table[] is consistent
- */
-static DEFINE_SPINLOCK(mfp_spin_lock);
-
-static void __iomem *mfpr_mmio_base = (void __iomem *)&__REG(MFPR_BASE);
-
-struct pxa3xx_mfp_pin {
-	unsigned long	config;		/* -1 for not configured */
-	unsigned long	mfpr_off;	/* MFPRxx Register offset */
-	unsigned long	mfpr_run;	/* Run-Mode Register Value */
-	unsigned long	mfpr_lpm;	/* Low Power Mode Register Value */
-};
-
-static struct pxa3xx_mfp_pin mfp_table[MFP_PIN_MAX];
-
-/* mapping of MFP_LPM_* definitions to MFPR_LPM_* register bits */
-static const unsigned long mfpr_lpm[] = {
-	MFPR_LPM_INPUT,
-	MFPR_LPM_DRIVE_LOW,
-	MFPR_LPM_DRIVE_HIGH,
-	MFPR_LPM_PULL_LOW,
-	MFPR_LPM_PULL_HIGH,
-	MFPR_LPM_FLOAT,
-};
-
-/* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */
-static const unsigned long mfpr_pull[] = {
-	MFPR_PULL_NONE,
-	MFPR_PULL_LOW,
-	MFPR_PULL_HIGH,
-	MFPR_PULL_BOTH,
-};
-
-/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
-static const unsigned long mfpr_edge[] = {
-	MFPR_EDGE_NONE,
-	MFPR_EDGE_RISE,
-	MFPR_EDGE_FALL,
-	MFPR_EDGE_BOTH,
-};
-
-#define mfpr_readl(off)			\
-	__raw_readl(mfpr_mmio_base + (off))
-
-#define mfpr_writel(off, val)		\
-	__raw_writel(val, mfpr_mmio_base + (off))
-
-#define mfp_configured(p)	((p)->config != -1)
-
-/*
- * perform a read-back of any MFPR register to make sure the
- * previous writings are finished
- */
-#define mfpr_sync()	(void)__raw_readl(mfpr_mmio_base + 0)
-
-static inline void __mfp_config_run(struct pxa3xx_mfp_pin *p)
-{
-	if (mfp_configured(p))
-		mfpr_writel(p->mfpr_off, p->mfpr_run);
-}
-
-static inline void __mfp_config_lpm(struct pxa3xx_mfp_pin *p)
-{
-	if (mfp_configured(p)) {
-		unsigned long mfpr_clr = (p->mfpr_run & ~MFPR_EDGE_BOTH) | MFPR_EDGE_CLEAR;
-		if (mfpr_clr != p->mfpr_run)
-			mfpr_writel(p->mfpr_off, mfpr_clr);
-		if (p->mfpr_lpm != mfpr_clr)
-			mfpr_writel(p->mfpr_off, p->mfpr_lpm);
-	}
-}
-
-void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num)
-{
-	unsigned long flags;
-	int i;
-
-	spin_lock_irqsave(&mfp_spin_lock, flags);
-
-	for (i = 0; i < num; i++, mfp_cfgs++) {
-		unsigned long tmp, c = *mfp_cfgs;
-		struct pxa3xx_mfp_pin *p;
-		int pin, af, drv, lpm, edge, pull;
-
-		pin = MFP_PIN(c);
-		BUG_ON(pin >= MFP_PIN_MAX);
-		p = &mfp_table[pin];
-
-		af  = MFP_AF(c);
-		drv = MFP_DS(c);
-		lpm = MFP_LPM_STATE(c);
-		edge = MFP_LPM_EDGE(c);
-		pull = MFP_PULL(c);
-
-		/* run-mode pull settings will conflict with MFPR bits of
-		 * low power mode state,  calculate mfpr_run and mfpr_lpm
-		 * individually if pull != MFP_PULL_NONE
-		 */
-		tmp = MFPR_AF_SEL(af) | MFPR_DRIVE(drv);
-
-		if (likely(pull == MFP_PULL_NONE)) {
-			p->mfpr_run = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
-			p->mfpr_lpm = p->mfpr_run;
-		} else {
-			p->mfpr_lpm = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
-			p->mfpr_run = tmp | mfpr_pull[pull];
-		}
-
-		p->config = c; __mfp_config_run(p);
-	}
-
-	mfpr_sync();
-	spin_unlock_irqrestore(&mfp_spin_lock, flags);
-}
-
-unsigned long pxa3xx_mfp_read(int mfp)
-{
-	unsigned long val, flags;
-
-	BUG_ON(mfp >= MFP_PIN_MAX);
-
-	spin_lock_irqsave(&mfp_spin_lock, flags);
-	val = mfpr_readl(mfp_table[mfp].mfpr_off);
-	spin_unlock_irqrestore(&mfp_spin_lock, flags);
-
-	return val;
-}
-
-void pxa3xx_mfp_write(int mfp, unsigned long val)
-{
-	unsigned long flags;
-
-	BUG_ON(mfp >= MFP_PIN_MAX);
-
-	spin_lock_irqsave(&mfp_spin_lock, flags);
-	mfpr_writel(mfp_table[mfp].mfpr_off, val);
-	mfpr_sync();
-	spin_unlock_irqrestore(&mfp_spin_lock, flags);
-}
-
-void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *map)
-{
-	struct pxa3xx_mfp_addr_map *p;
-	unsigned long offset, flags;
-	int i;
-
-	spin_lock_irqsave(&mfp_spin_lock, flags);
-
-	for (p = map; p->start != MFP_PIN_INVALID; p++) {
-		offset = p->offset;
-		i = p->start;
-
-		do {
-			mfp_table[i].mfpr_off = offset;
-			mfp_table[i].mfpr_run = 0;
-			mfp_table[i].mfpr_lpm = 0;
-			offset += 4; i++;
-		} while ((i <= p->end) && (p->end != -1));
-	}
-
-	spin_unlock_irqrestore(&mfp_spin_lock, flags);
-}
-
-void __init pxa3xx_init_mfp(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
-		mfp_table[i].config = -1;
-}
-
 #ifdef CONFIG_PM
 /*
  * Configure the MFPs appropriately for suspend/resume.
@@ -207,23 +33,13 @@ void __init pxa3xx_init_mfp(void)
  */
 static int pxa3xx_mfp_suspend(struct sys_device *d, pm_message_t state)
 {
-	int pin;
-
-	for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++) {
-		struct pxa3xx_mfp_pin *p = &mfp_table[pin];
-		__mfp_config_lpm(p);
-	}
+	mfp_config_lpm();
 	return 0;
 }
 
 static int pxa3xx_mfp_resume(struct sys_device *d)
 {
-	int pin;
-
-	for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++) {
-		struct pxa3xx_mfp_pin *p = &mfp_table[pin];
-		__mfp_config_run(p);
-	}
+	mfp_config_run();
 
 	/* clear RDH bit when MFP settings are restored
 	 *
@@ -231,7 +47,6 @@ static int pxa3xx_mfp_resume(struct sys_device *d)
 	 * preserve them here in case they will be referenced later
 	 */
 	ASCR &= ~(ASCR_RDH | ASCR_D1S | ASCR_D2S | ASCR_D3S);
-
 	return 0;
 }
 #else
diff --git a/arch/arm/mach-pxa/pxa300.c b/arch/arm/mach-pxa/pxa300.c
index 37bb12d13ca2..4ba6d21f851c 100644
--- a/arch/arm/mach-pxa/pxa300.c
+++ b/arch/arm/mach-pxa/pxa300.c
@@ -23,7 +23,7 @@
 #include "devices.h"
 #include "clock.h"
 
-static struct pxa3xx_mfp_addr_map pxa300_mfp_addr_map[] __initdata = {
+static struct mfp_addr_map pxa300_mfp_addr_map[] __initdata = {
 
 	MFP_ADDR_X(GPIO0,   GPIO2,   0x00b4),
 	MFP_ADDR_X(GPIO3,   GPIO26,  0x027c),
@@ -72,7 +72,7 @@ static struct pxa3xx_mfp_addr_map pxa300_mfp_addr_map[] __initdata = {
 };
 
 /* override pxa300 MFP register addresses */
-static struct pxa3xx_mfp_addr_map pxa310_mfp_addr_map[] __initdata = {
+static struct mfp_addr_map pxa310_mfp_addr_map[] __initdata = {
 	MFP_ADDR_X(GPIO30,  GPIO98,   0x0418),
 	MFP_ADDR_X(GPIO7_2, GPIO12_2, 0x052C),
 
@@ -98,13 +98,13 @@ static struct clk_lookup pxa310_clkregs[] = {
 static int __init pxa300_init(void)
 {
 	if (cpu_is_pxa300() || cpu_is_pxa310()) {
-		pxa3xx_init_mfp();
-		pxa3xx_mfp_init_addr(pxa300_mfp_addr_map);
+		mfp_init_base(io_p2v(MFPR_BASE));
+		mfp_init_addr(pxa300_mfp_addr_map);
 		clks_register(ARRAY_AND_SIZE(common_clkregs));
 	}
 
 	if (cpu_is_pxa310()) {
-		pxa3xx_mfp_init_addr(pxa310_mfp_addr_map);
+		mfp_init_addr(pxa310_mfp_addr_map);
 		clks_register(ARRAY_AND_SIZE(pxa310_clkregs));
 	}
 
diff --git a/arch/arm/mach-pxa/pxa320.c b/arch/arm/mach-pxa/pxa320.c
index e708f4e0ecaf..8b3d97efadab 100644
--- a/arch/arm/mach-pxa/pxa320.c
+++ b/arch/arm/mach-pxa/pxa320.c
@@ -23,7 +23,7 @@
 #include "devices.h"
 #include "clock.h"
 
-static struct pxa3xx_mfp_addr_map pxa320_mfp_addr_map[] __initdata = {
+static struct mfp_addr_map pxa320_mfp_addr_map[] __initdata = {
 
 	MFP_ADDR_X(GPIO0,  GPIO4,   0x0124),
 	MFP_ADDR_X(GPIO5,  GPIO9,   0x028C),
@@ -86,8 +86,8 @@ static struct clk_lookup pxa320_clkregs[] = {
 static int __init pxa320_init(void)
 {
 	if (cpu_is_pxa320()) {
-		pxa3xx_init_mfp();
-		pxa3xx_mfp_init_addr(pxa320_mfp_addr_map);
+		mfp_init_base(io_p2v(MFPR_BASE));
+		mfp_init_addr(pxa320_mfp_addr_map);
 		clks_register(ARRAY_AND_SIZE(pxa320_clkregs));
 	}
 
diff --git a/arch/arm/mach-pxa/pxa930.c b/arch/arm/mach-pxa/pxa930.c
index f15dfa55f27f..71131742fffd 100644
--- a/arch/arm/mach-pxa/pxa930.c
+++ b/arch/arm/mach-pxa/pxa930.c
@@ -18,7 +18,7 @@
 
 #include <mach/pxa930.h>
 
-static struct pxa3xx_mfp_addr_map pxa930_mfp_addr_map[] __initdata = {
+static struct mfp_addr_map pxa930_mfp_addr_map[] __initdata = {
 
 	MFP_ADDR(GPIO0, 0x02e0),
 	MFP_ADDR(GPIO1, 0x02dc),
@@ -179,8 +179,8 @@ static struct pxa3xx_mfp_addr_map pxa930_mfp_addr_map[] __initdata = {
 static int __init pxa930_init(void)
 {
 	if (cpu_is_pxa930()) {
-		pxa3xx_init_mfp();
-		pxa3xx_mfp_init_addr(pxa930_mfp_addr_map);
+		mfp_init_base(io_p2v(MFPR_BASE));
+		mfp_init_addr(pxa930_mfp_addr_map);
 	}
 
 	return 0;