dt-bindings: pinctrl: {mediatek,ralink}: fix formatting

Change the style of description properties to plain style where there's no
need to preserve the line endings, and vice versa.

Fix capitalisation and indentation.

Fit the schemas to 80 columns for each line.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230317213011.13656-16-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1 files changed, 21 insertions, 20 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6795-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6795-pinctrl.yaml
index a78df32e6c39..c3bf98749fa4 100644
--- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6795-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6795-pinctrl.yaml
@@ -10,7 +10,7 @@ maintainers:
   - AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
   - Sean Wang <sean.wang@kernel.org>
 
-description: |
+description:
   The MediaTek's MT6795 Pin controller is used to control SoC pins.
 
 properties:
@@ -20,10 +20,10 @@ properties:
   gpio-controller: true
 
   '#gpio-cells':
-    description: |
+    description:
       Number of cells in GPIO specifier. Since the generic GPIO binding is used,
-      the amount of cells must be specified as 2. See the below
-      mentioned gpio binding representation for description of particular cells.
+      the amount of cells must be specified as 2. See the below mentioned gpio
+      binding representation for description of particular cells.
     const: 2
 
   gpio-ranges:
@@ -32,7 +32,7 @@ properties:
 
   reg:
     description:
-      Physical address base for gpio base and eint registers.
+      Physical address base for GPIO base and eint registers.
     minItems: 2
 
   reg-names:
@@ -65,8 +65,8 @@ patternProperties:
           A pinctrl node should contain at least one subnodes representing the
           pinctrl groups available on the machine. Each subnode will list the
           pins it needs, and how they should be configured, with regard to muxer
-          configuration, pullups, drive strength, input enable/disable and
-          input schmitt.
+          configuration, pullups, drive strength, input enable/disable and input
+          schmitt.
           An example of using macro:
           pincontroller {
             /* GPIO0 set as multifunction GPIO0 */
@@ -86,11 +86,10 @@ patternProperties:
 
         properties:
           pinmux:
-            description: |
+            description:
               Integer array, represents gpio pin number and mux setting.
               Supported pin number and mux varies for different SoCs, and are
-              defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
-              directly.
+              defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly.
 
           drive-strength:
             enum: [2, 4, 6, 8, 10, 12, 14, 16]
@@ -100,20 +99,20 @@ patternProperties:
               - type: boolean
               - enum: [100, 101, 102, 103]
                 description: mt6795 pull down PUPD/R0/R1 type define value.
-            description: |
-               For normal pull down type, it is not necessary to specify R1R0
-               values; When pull down type is PUPD/R0/R1, adding R1R0 defines
-               will set different resistance values.
+            description:
+              For normal pull down type, it is not necessary to specify R1R0
+              values; When pull down type is PUPD/R0/R1, adding R1R0 defines
+              will set different resistance values.
 
           bias-pull-up:
             oneOf:
               - type: boolean
               - enum: [100, 101, 102, 103]
                 description: mt6795 pull up PUPD/R0/R1 type define value.
-            description: |
-               For normal pull up type, it is not necessary to specify R1R0
-               values; When pull up type is PUPD/R0/R1, adding R1R0 defines
-               will set different resistance values.
+            description:
+              For normal pull up type, it is not necessary to specify R1R0
+              values; When pull up type is PUPD/R0/R1, adding R1R0 defines will
+              set different resistance values.
 
           bias-disable: true
 
@@ -132,7 +131,8 @@ patternProperties:
           mediatek,pull-up-adv:
             description: |
               Pull up setings for 2 pull resistors, R0 and R1. User can
-              configure those special pins. Valid arguments are described as below:
+              configure those special pins. Valid arguments are described as
+              below:
               0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
               1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
               2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
@@ -143,7 +143,8 @@ patternProperties:
           mediatek,pull-down-adv:
             description: |
               Pull down settings for 2 pull resistors, R0 and R1. User can
-              configure those special pins. Valid arguments are described as below:
+              configure those special pins. Valid arguments are described as
+              below:
               0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
               1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
               2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.