Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 "First cycle with Boris as NAND maintainer! Many (most) bullets stolen
  from him.

  Generic:
   - Migrated NAND LED trigger to be a generic MTD trigger

  NAND:
   - Introduction of the "ECC algorithm" concept, to avoid overloading
     the ECC mode field too much more
   - Replaced the nand_ecclayout infrastructure with something a little
     more flexible (finally!) and future proof
   - Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
     of this into their own tree as well
   - Prepare the sunxi NAND driver to receive DMA support
   - Handle bitflips in erased pages on GPMI revisions that do not
     support this in hardware.

  SPI NOR:
   - Start using the spi_flash_read() API for SPI drivers that support
     it (i.e., SPI drivers with special memory-mapped flash modes)

  And other small scattered improvments"

* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
  mtd: spi-nor: support GigaDevice gd25lq64c
  mtd: nand_bch: fix spelling of "probably"
  mtd: brcmnand: respect ECC algorithm set by NAND subsystem
  gpmi-nand: Handle ECC Errors in erased pages
  Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
  mtd: nand: add support for "nand-ecc-algo" DT property
  mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
  mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
  mtd: nand: read ECC algorithm from the new field
  mtd: nand: fsmc: validate ECC setup by checking algorithm directly
  mtd: nand: set ECC algorithm to Hamming on fallback
  staging: mt29f_spinand: set ECC algorithm explicitly
  CRIS v32: nand: set ECC algorithm explicitly
  mtd: nand: atmel: set ECC algorithm explicitly
  mtd: nand: davinci: set ECC algorithm explicitly
  mtd: nand: bf5xx: set ECC algorithm explicitly
  mtd: nand: omap2: Fix high memory dma prefetch transfer
  mtd: nand: omap2: Start dma request before enabling prefetch
  mtd: nandsim: add __init attribute
  mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
  ...

1 files changed, 152 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
new file mode 100644
index 000000000000..21055e210234
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
@@ -0,0 +1,152 @@
+Device tree bindings for OMAP general purpose memory controllers (GPMC)
+
+The actual devices are instantiated from the child nodes of a GPMC node.
+
+Required properties:
+
+ - compatible:		Should be set to one of the following:
+
+			ti,omap2420-gpmc (omap2420)
+			ti,omap2430-gpmc (omap2430)
+			ti,omap3430-gpmc (omap3430 & omap3630)
+			ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
+			ti,am3352-gpmc   (am335x devices)
+
+ - reg:			A resource specifier for the register space
+			(see the example below)
+ - ti,hwmods:		Should be set to "ti,gpmc" until the DT transition is
+			completed.
+ - #address-cells:	Must be set to 2 to allow memory address translation
+ - #size-cells:		Must be set to 1 to allow CS address passing
+ - gpmc,num-cs:		The maximum number of chip-select lines that controller
+			can support.
+ - gpmc,num-waitpins:	The maximum number of wait pins that controller can
+			support.
+ - ranges:		Must be set up to reflect the memory layout with four
+			integer values for each chip-select line in use:
+
+			   <cs-number> 0 <physical address of mapping> <size>
+
+			Currently, calculated values derived from the contents
+			of the per-CS register GPMC_CONFIG7 (as set up by the
+			bootloader) are used for the physical address decoding.
+			As this will change in the future, filling correct
+			values here is a requirement.
+ - interrupt-controller: The GPMC driver implements and interrupt controller for
+			the NAND events "fifoevent" and "termcount" plus the
+			rising/falling edges on the GPMC_WAIT pins.
+			The interrupt number mapping is as follows
+			0 - NAND_fifoevent
+			1 - NAND_termcount
+			2 - GPMC_WAIT0 pin edge
+			3 - GPMC_WAIT1 pin edge, and so on.
+ - interrupt-cells:	Must be set to 2
+ - gpio-controller:	The GPMC driver implements a GPIO controller for the
+			GPMC WAIT pins that can be used as general purpose inputs.
+			0 maps to GPMC_WAIT0 pin.
+ - gpio-cells:		Must be set to 2
+
+Timing properties for child nodes. All are optional and default to 0.
+
+ - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
+
+ Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
+ - gpmc,cs-on-ns:	Assertion time
+ - gpmc,cs-rd-off-ns:	Read deassertion time
+ - gpmc,cs-wr-off-ns:	Write deassertion time
+
+ ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
+ - gpmc,adv-on-ns:	Assertion time
+ - gpmc,adv-rd-off-ns:	Read deassertion time
+ - gpmc,adv-wr-off-ns:	Write deassertion time
+ - gpmc,adv-aad-mux-on-ns:	Assertion time for AAD
+ - gpmc,adv-aad-mux-rd-off-ns:	Read deassertion time for AAD
+ - gpmc,adv-aad-mux-wr-off-ns:	Write deassertion time for AAD
+
+ WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
+ - gpmc,we-on-ns	Assertion time
+ - gpmc,we-off-ns:	Deassertion time
+
+ OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
+ - gpmc,oe-on-ns:	Assertion time
+ - gpmc,oe-off-ns:	Deassertion time
+ - gpmc,oe-aad-mux-on-ns:	Assertion time for AAD
+ - gpmc,oe-aad-mux-off-ns:	Deassertion time for AAD
+
+ Access time and cycle time timings (in nanoseconds) corresponding to
+ GPMC_CONFIG5:
+ - gpmc,page-burst-access-ns: 	Multiple access word delay
+ - gpmc,access-ns:		Start-cycle to first data valid delay
+ - gpmc,rd-cycle-ns:		Total read cycle time
+ - gpmc,wr-cycle-ns:		Total write cycle time
+ - gpmc,bus-turnaround-ns:	Turn-around time between successive accesses
+ - gpmc,cycle2cycle-delay-ns:	Delay between chip-select pulses
+ - gpmc,clk-activation-ns: 	GPMC clock activation time
+ - gpmc,wait-monitoring-ns:	Start of wait monitoring with regard to valid
+				data
+
+Boolean timing parameters. If property is present parameter enabled and
+disabled if omitted:
+ - gpmc,adv-extra-delay:	ADV signal is delayed by half GPMC clock
+ - gpmc,cs-extra-delay:		CS signal is delayed by half GPMC clock
+ - gpmc,cycle2cycle-diffcsen:	Add "cycle2cycle-delay" between successive
+				accesses to a different CS
+ - gpmc,cycle2cycle-samecsen:	Add "cycle2cycle-delay" between successive
+				accesses to the same CS
+ - gpmc,oe-extra-delay:		OE signal is delayed by half GPMC clock
+ - gpmc,we-extra-delay:		WE signal is delayed by half GPMC clock
+ - gpmc,time-para-granularity:	Multiply all access times by 2
+
+The following are only applicable to OMAP3+ and AM335x:
+ - gpmc,wr-access-ns:		In synchronous write mode, for single or
+				burst accesses, defines the number of
+				GPMC_FCLK cycles from start access time
+				to the GPMC_CLK rising edge used by the
+				memory device for the first data capture.
+ - gpmc,wr-data-mux-bus-ns:	In address-data multiplex mode, specifies
+				the time when the first data is driven on
+				the address-data bus.
+
+GPMC chip-select settings properties for child nodes. All are optional.
+
+- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
+- gpmc,burst-wrap	Enables wrap bursting
+- gpmc,burst-read	Enables read page/burst mode
+- gpmc,burst-write	Enables write page/burst mode
+- gpmc,device-width	Total width of device(s) connected to a GPMC
+			chip-select in bytes. The GPMC supports 8-bit
+			and 16-bit devices and so this property must be
+			1 or 2.
+- gpmc,mux-add-data	Address and data multiplexing configuration.
+			Valid values are 1 for address-address-data
+			multiplexing mode and 2 for address-data
+			multiplexing mode.
+- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
+			is this is not set.
+- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
+			is this is not set.
+- gpmc,wait-pin		Wait-pin used by client. Must be less than
+			"gpmc,num-waitpins".
+- gpmc,wait-on-read	Enables wait monitoring on reads.
+- gpmc,wait-on-write	Enables wait monitoring on writes.
+
+Example for an AM33xx board:
+
+	gpmc: gpmc@50000000 {
+		compatible = "ti,am3352-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x50000000 0x2000>;
+		interrupts = <100>;
+
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		/* child nodes go here */
+	};