Merge branch 'pci/misc'

- Reorder struct pci_dev to avoid holes and reduce size (Christophe
  JAILLET)

- Change pdev->rom_attr_enabled to single bit since it's only a boolean
  value (Christophe JAILLET)

- Use struct_size() in pirq_convert_irt_table() instead of hand-writing it
  (Christophe JAILLET)

- Explicitly include correct DT includes to untangle headers (Rob Herring)

- Fix a DOE race between destroy_work_on_stack() and the stack-allocated
  task->work struct going out of scope in pci_doe() (Ira Weiny)

- Use pci_dev_id() when possible instead of manually composing ID from
  dev->bus->number and dev->devfn (Xiongfeng Wang, Zheng Zengkai)

- Move pci_create_resource_files() declarations to linux/pci.h for alpha
  build warnings (Arnd Bergmann)

- Remove unused hotplug function declarations (Yue Haibing)

- Remove unused mvebu struct mvebu_pcie.busn (Pali Rohár)

- Unexport pcie_port_bus_type (Bjorn Helgaas)

- Remove unnecessary sysfs ID local variable initialization (Bjorn Helgaas)

- Fix BAR value printk formatting to accommodate 32-bit values (Bjorn
  Helgaas)

- Use consistent pointer types for config access syscall get_user() and
  put_user() uses (Bjorn Helgaas)

- Simplify AER_RECOVER_RING_SIZE definition (Bjorn Helgaas)

- Simplify pci_pio_to_address() (Bjorn Helgaas)

- Simplify pci_dev_driver() (Bjorn Helgaas)

- Fix pci_bus_resetable(), pci_slot_resetable() name typos (Bjorn Helgaas)

- Fix code and doc typos and code formatting (Bjorn Helgaas)

- Tidy config space save/restore messages (Bjorn Helgaas)

* pci/misc:
  PCI: Tidy config space save/restore messages
  PCI: Fix code formatting inconsistencies
  PCI: Fix typos in docs and comments
  PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
  PCI: Simplify pci_dev_driver()
  PCI: Simplify pci_pio_to_address()
  PCI/AER: Simplify AER_RECOVER_RING_SIZE definition
  PCI: Use consistent put_user() pointer types
  PCI: Fix printk field formatting
  PCI: Remove unnecessary initializations
  PCI: Unexport pcie_port_bus_type
  PCI: mvebu: Remove unused busn member
  PCI: Remove unused function declarations
  PCI/sysfs: Move declarations to linux/pci.h
  PCI/P2PDMA: Use pci_dev_id() to simplify the code
  PCI/IOV: Use pci_dev_id() to simplify the code
  PCI/AER: Use pci_dev_id() to simplify the code
  PCI: apple: Use pci_dev_id() to simplify the code
  PCI/DOE: Fix destroy_work_on_stack() race
  PCI: Explicitly include correct DT includes
  x86/PCI: Use struct_size() in pirq_convert_irt_table()
  PCI: Change pdev->rom_attr_enabled to single bit
  PCI: Reorder pci_dev fields to reduce holes

1 files changed, 6 insertions, 6 deletions

diff --git a/Documentation/PCI/pci-error-recovery.rst b/Documentation/PCI/pci-error-recovery.rst
index c237596f67e3..0c7552a00c8c 100644
--- a/Documentation/PCI/pci-error-recovery.rst
+++ b/Documentation/PCI/pci-error-recovery.rst
@@ -17,7 +17,7 @@ chipsets are able to deal with these errors; these include PCI-E chipsets,
 and the PCI-host bridges found on IBM Power4, Power5 and Power6-based
 pSeries boxes. A typical action taken is to disconnect the affected device,
 halting all I/O to it.  The goal of a disconnection is to avoid system
-corruption; for example, to halt system memory corruption due to DMA's
+corruption; for example, to halt system memory corruption due to DMAs
 to "wild" addresses. Typically, a reconnection mechanism is also
 offered, so that the affected PCI device(s) are reset and put back
 into working condition. The reset phase requires coordination
@@ -178,9 +178,9 @@ is STEP 6 (Permanent Failure).
    complex and not worth implementing.
 
    The current powerpc implementation doesn't much care if the device
-   attempts I/O at this point, or not.  I/O's will fail, returning
+   attempts I/O at this point, or not.  I/Os will fail, returning
    a value of 0xff on read, and writes will be dropped. If more than
-   EEH_MAX_FAILS I/O's are attempted to a frozen adapter, EEH
+   EEH_MAX_FAILS I/Os are attempted to a frozen adapter, EEH
    assumes that the device driver has gone into an infinite loop
    and prints an error to syslog.  A reboot is then required to
    get the device working again.
@@ -204,7 +204,7 @@ instead will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset)
 .. note::
 
    The following is proposed; no platform implements this yet:
-   Proposal: All I/O's should be done _synchronously_ from within
+   Proposal: All I/Os should be done _synchronously_ from within
    this callback, errors triggered by them will be returned via
    the normal pci_check_whatever() API, no new error_detected()
    callback will be issued due to an error happening here. However,
@@ -258,7 +258,7 @@ Powerpc platforms implement two levels of slot reset:
 soft reset(default) and fundamental(optional) reset.
 
 Powerpc soft reset consists of asserting the adapter #RST line and then
-restoring the PCI BAR's and PCI configuration header to a state
+restoring the PCI BARs and PCI configuration header to a state
 that is equivalent to what it would be after a fresh system
 power-on followed by power-on BIOS/system firmware initialization.
 Soft reset is also known as hot-reset.
@@ -362,7 +362,7 @@ permanent failure in some way.  If the device is hotplug-capable,
 the operator will probably want to remove and replace the device.
 Note, however, not all failures are truly "permanent". Some are
 caused by over-heating, some by a poorly seated card. Many
-PCI error events are caused by software bugs, e.g. DMA's to
+PCI error events are caused by software bugs, e.g. DMAs to
 wild addresses or bogus split transactions due to programming
 errors. See the discussion in Documentation/powerpc/eeh-pci-error-recovery.rst
 for additional detail on real-life experience of the causes of