Age | Commit message (Collapse) | Author | Files | Lines |
|
The helper __lookup_addr() can be used in mptcp_pm_nl_get_local_id()
and mptcp_pm_nl_is_backup() to simplify the code, and avoid code
duplication.
Co-developed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241115-net-next-mptcp-pm-lockless-dump-v1-2-f4a1bcb4ca2c@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To return an endpoint to the userspace via Netlink, and to dump all of
them, the endpoint list was iterated while holding the pernet->lock, but
only to read the content of the list.
In these cases, the spin locks can be replaced by RCU read ones, and use
the _rcu variants to iterate over the entries list in a lockless way.
Note that the __lookup_addr_by_id() helper has been modified to use the
_rcu variants of list_for_each_entry(), but with an extra conditions, so
it can be called either while the RCU read lock is held, or when the
associated pernet->lock is held.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241115-net-next-mptcp-pm-lockless-dump-v1-1-f4a1bcb4ca2c@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc8).
Conflicts:
tools/testing/selftests/net/.gitignore
252e01e68241 ("selftests: net: add netlink-dumps to .gitignore")
be43a6b23829 ("selftests: ncdevmem: Move ncdevmem under drivers/net/hw")
https://lore.kernel.org/all/20241113122359.1b95180a@canb.auug.org.au/
drivers/net/phy/phylink.c
671154f174e0 ("net: phylink: ensure PHY momentary link-fails are handled")
7530ea26c810 ("net: phylink: remove "using_mac_select_pcs"")
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c
5b366eae7193 ("stmmac: dwmac-intel-plat: fix call balance of tx_clk handling routines")
e96321fad3ad ("net: ethernet: Switch back to struct platform_driver::remove()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In mptcp_pm_create_subflow_or_signal_addr(), rcu_read_(un)lock() are
used as expected to iterate over the list of local addresses, but
list_for_each_entry() was used instead of list_for_each_entry_rcu() in
__lookup_addr(). It is important to use this variant which adds the
required READ_ONCE() (and diagnostic checks if enabled).
Because __lookup_addr() is also used in mptcp_pm_nl_set_flags() where it
is called under the pernet->lock and not rcu_read_lock(), an extra
condition is then passed to help the diagnostic checks making sure
either the associated spin lock or the RCU lock is held.
Fixes: 86e39e04482b ("mptcp: keep track of local endpoint still available for each msk")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241112-net-mptcp-misc-6-12-pm-v1-3-b835580cefa8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When traversing userspace_pm_local_addr_list and deleting an entry from
it in mptcp_pm_nl_remove_doit(), msk->pm.lock should be held.
This patch holds this lock before mptcp_userspace_pm_lookup_addr_by_id()
and releases it after list_move() in mptcp_pm_nl_remove_doit().
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241112-net-mptcp-misc-6-12-pm-v1-2-b835580cefa8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Just like in-kernel pm, when userspace pm does set_flags, it needs to send
out MP_PRIO signal, and also modify the flags of the corresponding address
entry in the local address list. This patch implements the missing logic.
Traverse all address entries on userspace_pm_local_addr_list to find the
local address entry, if bkup is true, set the flags of this entry with
FLAG_BACKUP, otherwise, clear FLAG_BACKUP.
Fixes: 892f396c8e68 ("mptcp: netlink: issue MP_PRIO signals from userspace PMs")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241112-net-mptcp-misc-6-12-pm-v1-1-b835580cefa8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In 'mptcp_reset_tout_timer', promote 'probe_timestamp' to unsigned long
to avoid possible integer overflow. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Kandybka <d.kandybka@gmail.com>
Link: https://patch.msgid.link/20241107103657.1560536-1-d.kandybka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Additional active subflows - i.e. created by the in kernel path
manager - are included into the subflow list before starting the
3whs.
A racing recvmsg() spooling data received on an already established
subflow would unconditionally call tcp_cleanup_rbuf() on all the
current subflows, potentially hitting a divide by zero error on
the newly created ones.
Explicitly check that the subflow is in a suitable state before
invoking tcp_cleanup_rbuf().
Fixes: c76c6956566f ("mptcp: call tcp_cleanup_rbuf on subflows")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/02374660836e1b52afc91966b7535c8c5f7bafb0.1731060874.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric reported a division by zero splat in the MPTCP protocol:
Oops: divide error: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 UID: 0 PID: 6094 Comm: syz-executor317 Not tainted
6.12.0-rc5-syzkaller-00291-g05b92660cdfe #0
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 09/13/2024
RIP: 0010:__tcp_select_window+0x5b4/0x1310 net/ipv4/tcp_output.c:3163
Code: f6 44 01 e3 89 df e8 9b 75 09 f8 44 39 f3 0f 8d 11 ff ff ff e8
0d 74 09 f8 45 89 f4 e9 04 ff ff ff e8 00 74 09 f8 44 89 f0 99 <f7> 7c
24 14 41 29 d6 45 89 f4 e9 ec fe ff ff e8 e8 73 09 f8 48 89
RSP: 0018:ffffc900041f7930 EFLAGS: 00010293
RAX: 0000000000017e67 RBX: 0000000000017e67 RCX: ffffffff8983314b
RDX: 0000000000000000 RSI: ffffffff898331b0 RDI: 0000000000000004
RBP: 00000000005d6000 R08: 0000000000000004 R09: 0000000000017e67
R10: 0000000000003e80 R11: 0000000000000000 R12: 0000000000003e80
R13: ffff888031d9b440 R14: 0000000000017e67 R15: 00000000002eb000
FS: 00007feb5d7f16c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007feb5d8adbb8 CR3: 0000000074e4c000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__tcp_cleanup_rbuf+0x3e7/0x4b0 net/ipv4/tcp.c:1493
mptcp_rcv_space_adjust net/mptcp/protocol.c:2085 [inline]
mptcp_recvmsg+0x2156/0x2600 net/mptcp/protocol.c:2289
inet_recvmsg+0x469/0x6a0 net/ipv4/af_inet.c:885
sock_recvmsg_nosec net/socket.c:1051 [inline]
sock_recvmsg+0x1b2/0x250 net/socket.c:1073
__sys_recvfrom+0x1a5/0x2e0 net/socket.c:2265
__do_sys_recvfrom net/socket.c:2283 [inline]
__se_sys_recvfrom net/socket.c:2279 [inline]
__x64_sys_recvfrom+0xe0/0x1c0 net/socket.c:2279
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7feb5d857559
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 51 18 00 00 90 48 89 f8 48
89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d
01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007feb5d7f1208 EFLAGS: 00000246 ORIG_RAX: 000000000000002d
RAX: ffffffffffffffda RBX: 00007feb5d8e1318 RCX: 00007feb5d857559
RDX: 000000800000000e RSI: 0000000000000000 RDI: 0000000000000003
RBP: 00007feb5d8e1310 R08: 0000000000000000 R09: ffffffff81000000
R10: 0000000000000100 R11: 0000000000000246 R12: 00007feb5d8e131c
R13: 00007feb5d8ae074 R14: 000000800000000e R15: 00000000fffffdef
and provided a nice reproducer.
The root cause is the current bad handling of racing disconnect.
After the blamed commit below, sk_wait_data() can return (with
error) with the underlying socket disconnected and a zero rcv_mss.
Catch the error and return without performing any additional
operations on the current socket.
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 419ce133ab92 ("tcp: allow again tcp_disconnect() when threads are waiting")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/8c82ecf71662ecbc47bf390f9905de70884c9f2d.1731060874.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
subflow_ulp_clone()
The variable has already been assigned in the subflow_create_ctx(),
So we don't need to reassign this variable in the subflow_ulp_clone().
Signed-off-by: MoYuanhao <moyuanhao3676@163.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241106071035.2591-1-moyuanhao3676@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc7).
Conflicts:
drivers/net/ethernet/freescale/enetc/enetc_pf.c
e15c5506dd39 ("net: enetc: allocate vf_state during PF probes")
3774409fd4c6 ("net: enetc: build enetc_pf_common.c as a separate module")
https://lore.kernel.org/20241105114100.118bd35e@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/ti/am65-cpsw-nuss.c
de794169cf17 ("net: ethernet: ti: am65-cpsw: Fix multi queue Rx on J7")
4a7b2ba94a59 ("net: ethernet: ti: am65-cpsw: Use tstats instead of open coded version")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mptcp_get_available_schedulers() needs to iterate over the schedulers'
list only to read the names: it doesn't modify anything there.
In this case, it is enough to hold the RCU read lock, no need to combine
this with the associated spin lock as it was done since its introduction
in commit 73c900aa3660 ("mptcp: add net.mptcp.available_schedulers").
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241104-net-next-mptcp-sched-unneeded-lock-v2-1-2ccc1e0c750c@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The local address entries on userspace_pm_local_addr_list are allocated
by sock_kmalloc().
It's then required to use sock_kfree_s() instead of kfree() to free
these entries in order to adjust the allocated size on the sk side.
Fixes: 24430f8bf516 ("mptcp: add address into userspace pm list")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241104-net-mptcp-misc-6-12-v1-2-c13f2ff1656f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During the switch to YNL, the command to list all endpoints has been
accidentally restricted to users with admin permissions.
It looks like there are no reasons to have this restriction which makes
it harder for a user to quickly check if the endpoint list has been
correctly populated by an automated tool. Best to go back to the
previous behaviour then.
mptcp_pm_gen.c has been modified using ynl-gen-c.py:
$ ./tools/net/ynl/ynl-gen-c.py --mode kernel \
--spec Documentation/netlink/specs/mptcp_pm.yaml --source \
-o net/mptcp/mptcp_pm_gen.c
The header file doesn't need to be regenerated.
Fixes: 1d0507f46843 ("net: mptcp: convert netlink from small_ops to ops")
Cc: stable@vger.kernel.org
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241104-net-mptcp-misc-6-12-v1-1-c13f2ff1656f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc6).
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/mld-mac80211.c
cbe84e9ad5e2 ("wifi: iwlwifi: mvm: really send iwl_txpower_constraints_cmd")
188a1bf89432 ("wifi: mac80211: re-order assigning channel in activate links")
https://lore.kernel.org/all/20241028123621.7bbb131b@canb.auug.org.au/
net/mac80211/cfg.c
c4382d5ca1af ("wifi: mac80211: update the right link for tx power")
8dd0498983ee ("wifi: mac80211: Fix setting txpower with emulate_chanctx")
drivers/net/ethernet/intel/ice/ice_ptp_hw.h
6e58c3310622 ("ice: fix crash on probe for DPLL enabled E810 LOM")
e4291b64e118 ("ice: Align E810T GPIO to other products")
ebb2693f8fbd ("ice: Read SDP section from NVM for pin definitions")
ac532f4f4251 ("ice: Cleanup unused declarations")
https://lore.kernel.org/all/20241030120524.1ee1af18@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RFC8684 suggests use of "Middlebox interference (code 0x06)" in case of
fully established subflow that carries data at TCP level with no DSS
sub-option.
This is generally the case when mpext is NULL or mpext->use_map is 0:
use a dedicated value of 'mapping_status' and use it before closing the
socket in subflow_check_data_avail().
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/518
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-4-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MPTCP path manager event handler mptcp_pm_connection_closed
interface has been added in the commit 1b1c7a0ef7f3 ("mptcp: Add path
manager interface") but it was an empty function from then on.
With such name, it sounds good to invoke mptcp_event with the
MPTCP_EVENT_CLOSED event type from it. It also removes a bit of
duplicated code.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-3-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We introduce the same handling for potential data races with the
'fully_established' flag in subflow as previously done for
msk->fully_established.
Additionally, we make a crucial change: convert the subflow's
'fully_established' from 'bit_field' to 'bool' type. This is
necessary because methods for avoiding data races don't work well
with 'bit_field'. Specifically, the 'READ_ONCE' needs to know
the size of the variable being accessed, which is not supported in
'bit_field'. Also, 'test_bit' expect the address of 'bit_field'.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/516
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-2-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the subflow is considered as "staled", it is better to avoid it to
send an ACK carrying an ADD_ADDR or RM_ADDR. Another subflow, if any,
will then be selected.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-1-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enabling CONFIG_PROVE_RCU_LIST with its dependence CONFIG_RCU_EXPERT
creates this splat when an MPTCP socket is created:
=============================
WARNING: suspicious RCU usage
6.12.0-rc2+ #11 Not tainted
-----------------------------
net/mptcp/sched.c:44 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by mptcp_connect/176.
stack backtrace:
CPU: 0 UID: 0 PID: 176 Comm: mptcp_connect Not tainted 6.12.0-rc2+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:123)
lockdep_rcu_suspicious (kernel/locking/lockdep.c:6822)
mptcp_sched_find (net/mptcp/sched.c:44 (discriminator 7))
mptcp_init_sock (net/mptcp/protocol.c:2867 (discriminator 1))
? sock_init_data_uid (arch/x86/include/asm/atomic.h:28)
inet_create.part.0.constprop.0 (net/ipv4/af_inet.c:386)
? __sock_create (include/linux/rcupdate.h:347 (discriminator 1))
__sock_create (net/socket.c:1576)
__sys_socket (net/socket.c:1671)
? __pfx___sys_socket (net/socket.c:1712)
? do_user_addr_fault (arch/x86/mm/fault.c:1419 (discriminator 1))
__x64_sys_socket (net/socket.c:1728)
do_syscall_64 (arch/x86/entry/common.c:52 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
That's because when the socket is initialised, rcu_read_lock() is not
used despite the explicit comment written above the declaration of
mptcp_sched_find() in sched.c. Adding the missing lock/unlock avoids the
warning.
Fixes: 1730b2b2c5a5 ("mptcp: add sched in mptcp_sock")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/523
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241021-net-mptcp-sched-lock-v1-1-637759cf061c@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change ynl-gen-c.py to use NLA_BE16 and NLA_BE32 types to represent
big-endian u16 and u32 ynl types.
Doing this enables those attributes to have range checks applied, as
the validator will then convert to host endianness prior to validation.
The autogenerated kernel/uapi code have been regenerated by running:
./tools/net/ynl/ynl-regen.sh -f
This changes the policy types of the following attributes:
FOU_ATTR_PORT (NLA_U16 -> NLA_BE16)
FOU_ATTR_PEER_PORT (NLA_U16 -> NLA_BE16)
These two are used with nla_get_be16/nla_put_be16().
MPTCP_PM_ADDR_ATTR_ADDR4 (NLA_U32 -> NLA_BE32)
This one is used with nla_get_in_addr/nla_put_in_addr(),
which uses nla_get_be32/nla_put_be32().
IOWs the generated changes are AFAICT aligned with their implementations.
The generated userspace code remains identical, and have been verified
by comparing the output generated by the following command:
make -C tools/net/ynl/generated
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241017094704.3222173-1-ast@fiberby.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c1e ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c41c ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Syzkaller reported this splat:
==================================================================
BUG: KASAN: slab-use-after-free in mptcp_pm_nl_rm_addr_or_subflow+0xb44/0xcc0 net/mptcp/pm_netlink.c:881
Read of size 4 at addr ffff8880569ac858 by task syz.1.2799/14662
CPU: 0 UID: 0 PID: 14662 Comm: syz.1.2799 Not tainted 6.12.0-rc2-syzkaller-00307-g36c254515dc6 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:377 [inline]
print_report+0xc3/0x620 mm/kasan/report.c:488
kasan_report+0xd9/0x110 mm/kasan/report.c:601
mptcp_pm_nl_rm_addr_or_subflow+0xb44/0xcc0 net/mptcp/pm_netlink.c:881
mptcp_pm_nl_rm_subflow_received net/mptcp/pm_netlink.c:914 [inline]
mptcp_nl_remove_id_zero_address+0x305/0x4a0 net/mptcp/pm_netlink.c:1572
mptcp_pm_nl_del_addr_doit+0x5c9/0x770 net/mptcp/pm_netlink.c:1603
genl_family_rcv_msg_doit+0x202/0x2f0 net/netlink/genetlink.c:1115
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0x565/0x800 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x165/0x410 net/netlink/af_netlink.c:2551
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1331 [inline]
netlink_unicast+0x53c/0x7f0 net/netlink/af_netlink.c:1357
netlink_sendmsg+0x8b8/0xd70 net/netlink/af_netlink.c:1901
sock_sendmsg_nosec net/socket.c:729 [inline]
__sock_sendmsg net/socket.c:744 [inline]
____sys_sendmsg+0x9ae/0xb40 net/socket.c:2607
___sys_sendmsg+0x135/0x1e0 net/socket.c:2661
__sys_sendmsg+0x117/0x1f0 net/socket.c:2690
do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline]
__do_fast_syscall_32+0x73/0x120 arch/x86/entry/common.c:386
do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411
entry_SYSENTER_compat_after_hwframe+0x84/0x8e
RIP: 0023:0xf7fe4579
Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d b4 26 00 00 00 00 8d b4 26 00 00 00 00
RSP: 002b:00000000f574556c EFLAGS: 00000296 ORIG_RAX: 0000000000000172
RAX: ffffffffffffffda RBX: 000000000000000b RCX: 0000000020000140
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000296 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Allocated by task 5387:
kasan_save_stack+0x33/0x60 mm/kasan/common.c:47
kasan_save_track+0x14/0x30 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:394
kmalloc_noprof include/linux/slab.h:878 [inline]
kzalloc_noprof include/linux/slab.h:1014 [inline]
subflow_create_ctx+0x87/0x2a0 net/mptcp/subflow.c:1803
subflow_ulp_init+0xc3/0x4d0 net/mptcp/subflow.c:1956
__tcp_set_ulp net/ipv4/tcp_ulp.c:146 [inline]
tcp_set_ulp+0x326/0x7f0 net/ipv4/tcp_ulp.c:167
mptcp_subflow_create_socket+0x4ae/0x10a0 net/mptcp/subflow.c:1764
__mptcp_subflow_connect+0x3cc/0x1490 net/mptcp/subflow.c:1592
mptcp_pm_create_subflow_or_signal_addr+0xbda/0x23a0 net/mptcp/pm_netlink.c:642
mptcp_pm_nl_fully_established net/mptcp/pm_netlink.c:650 [inline]
mptcp_pm_nl_work+0x3a1/0x4f0 net/mptcp/pm_netlink.c:943
mptcp_worker+0x15a/0x1240 net/mptcp/protocol.c:2777
process_one_work+0x958/0x1b30 kernel/workqueue.c:3229
process_scheduled_works kernel/workqueue.c:3310 [inline]
worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391
kthread+0x2c1/0x3a0 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
Freed by task 113:
kasan_save_stack+0x33/0x60 mm/kasan/common.c:47
kasan_save_track+0x14/0x30 mm/kasan/common.c:68
kasan_save_free_info+0x3b/0x60 mm/kasan/generic.c:579
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x51/0x70 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:230 [inline]
slab_free_hook mm/slub.c:2342 [inline]
slab_free mm/slub.c:4579 [inline]
kfree+0x14f/0x4b0 mm/slub.c:4727
kvfree+0x47/0x50 mm/util.c:701
kvfree_rcu_list+0xf5/0x2c0 kernel/rcu/tree.c:3423
kvfree_rcu_drain_ready kernel/rcu/tree.c:3563 [inline]
kfree_rcu_monitor+0x503/0x8b0 kernel/rcu/tree.c:3632
kfree_rcu_shrink_scan+0x245/0x3a0 kernel/rcu/tree.c:3966
do_shrink_slab+0x44f/0x11c0 mm/shrinker.c:435
shrink_slab+0x32b/0x12a0 mm/shrinker.c:662
shrink_one+0x47e/0x7b0 mm/vmscan.c:4818
shrink_many mm/vmscan.c:4879 [inline]
lru_gen_shrink_node mm/vmscan.c:4957 [inline]
shrink_node+0x2452/0x39d0 mm/vmscan.c:5937
kswapd_shrink_node mm/vmscan.c:6765 [inline]
balance_pgdat+0xc19/0x18f0 mm/vmscan.c:6957
kswapd+0x5ea/0xbf0 mm/vmscan.c:7226
kthread+0x2c1/0x3a0 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
Last potentially related work creation:
kasan_save_stack+0x33/0x60 mm/kasan/common.c:47
__kasan_record_aux_stack+0xba/0xd0 mm/kasan/generic.c:541
kvfree_call_rcu+0x74/0xbe0 kernel/rcu/tree.c:3810
subflow_ulp_release+0x2ae/0x350 net/mptcp/subflow.c:2009
tcp_cleanup_ulp+0x7c/0x130 net/ipv4/tcp_ulp.c:124
tcp_v4_destroy_sock+0x1c5/0x6a0 net/ipv4/tcp_ipv4.c:2541
inet_csk_destroy_sock+0x1a3/0x440 net/ipv4/inet_connection_sock.c:1293
tcp_done+0x252/0x350 net/ipv4/tcp.c:4870
tcp_rcv_state_process+0x379b/0x4f30 net/ipv4/tcp_input.c:6933
tcp_v4_do_rcv+0x1ad/0xa90 net/ipv4/tcp_ipv4.c:1938
sk_backlog_rcv include/net/sock.h:1115 [inline]
__release_sock+0x31b/0x400 net/core/sock.c:3072
__tcp_close+0x4f3/0xff0 net/ipv4/tcp.c:3142
__mptcp_close_ssk+0x331/0x14d0 net/mptcp/protocol.c:2489
mptcp_close_ssk net/mptcp/protocol.c:2543 [inline]
mptcp_close_ssk+0x150/0x220 net/mptcp/protocol.c:2526
mptcp_pm_nl_rm_addr_or_subflow+0x2be/0xcc0 net/mptcp/pm_netlink.c:878
mptcp_pm_nl_rm_subflow_received net/mptcp/pm_netlink.c:914 [inline]
mptcp_nl_remove_id_zero_address+0x305/0x4a0 net/mptcp/pm_netlink.c:1572
mptcp_pm_nl_del_addr_doit+0x5c9/0x770 net/mptcp/pm_netlink.c:1603
genl_family_rcv_msg_doit+0x202/0x2f0 net/netlink/genetlink.c:1115
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0x565/0x800 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x165/0x410 net/netlink/af_netlink.c:2551
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1331 [inline]
netlink_unicast+0x53c/0x7f0 net/netlink/af_netlink.c:1357
netlink_sendmsg+0x8b8/0xd70 net/netlink/af_netlink.c:1901
sock_sendmsg_nosec net/socket.c:729 [inline]
__sock_sendmsg net/socket.c:744 [inline]
____sys_sendmsg+0x9ae/0xb40 net/socket.c:2607
___sys_sendmsg+0x135/0x1e0 net/socket.c:2661
__sys_sendmsg+0x117/0x1f0 net/socket.c:2690
do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline]
__do_fast_syscall_32+0x73/0x120 arch/x86/entry/common.c:386
do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411
entry_SYSENTER_compat_after_hwframe+0x84/0x8e
The buggy address belongs to the object at ffff8880569ac800
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 88 bytes inside of
freed 512-byte region [ffff8880569ac800, ffff8880569aca00)
The buggy address belongs to the physical page:
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x569ac
head: order:2 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x4fff00000000040(head|node=1|zone=1|lastcpupid=0x7ff)
page_type: f5(slab)
raw: 04fff00000000040 ffff88801ac42c80 dead000000000100 dead000000000122
raw: 0000000000000000 0000000080100010 00000001f5000000 0000000000000000
head: 04fff00000000040 ffff88801ac42c80 dead000000000100 dead000000000122
head: 0000000000000000 0000000080100010 00000001f5000000 0000000000000000
head: 04fff00000000002 ffffea00015a6b01 ffffffffffffffff 0000000000000000
head: 0000000000000004 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 2, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC), pid 10238, tgid 10238 (kworker/u32:6), ts 597403252405, free_ts 597177952947
set_page_owner include/linux/page_owner.h:32 [inline]
post_alloc_hook+0x2d1/0x350 mm/page_alloc.c:1537
prep_new_page mm/page_alloc.c:1545 [inline]
get_page_from_freelist+0x101e/0x3070 mm/page_alloc.c:3457
__alloc_pages_noprof+0x223/0x25a0 mm/page_alloc.c:4733
alloc_pages_mpol_noprof+0x2c9/0x610 mm/mempolicy.c:2265
alloc_slab_page mm/slub.c:2412 [inline]
allocate_slab mm/slub.c:2578 [inline]
new_slab+0x2ba/0x3f0 mm/slub.c:2631
___slab_alloc+0xd1d/0x16f0 mm/slub.c:3818
__slab_alloc.constprop.0+0x56/0xb0 mm/slub.c:3908
__slab_alloc_node mm/slub.c:3961 [inline]
slab_alloc_node mm/slub.c:4122 [inline]
__kmalloc_cache_noprof+0x2c5/0x310 mm/slub.c:4290
kmalloc_noprof include/linux/slab.h:878 [inline]
kzalloc_noprof include/linux/slab.h:1014 [inline]
mld_add_delrec net/ipv6/mcast.c:743 [inline]
igmp6_leave_group net/ipv6/mcast.c:2625 [inline]
igmp6_group_dropped+0x4ab/0xe40 net/ipv6/mcast.c:723
__ipv6_dev_mc_dec+0x281/0x360 net/ipv6/mcast.c:979
addrconf_leave_solict net/ipv6/addrconf.c:2253 [inline]
__ipv6_ifa_notify+0x3f6/0xc30 net/ipv6/addrconf.c:6283
addrconf_ifdown.isra.0+0xef9/0x1a20 net/ipv6/addrconf.c:3982
addrconf_notify+0x220/0x19c0 net/ipv6/addrconf.c:3781
notifier_call_chain+0xb9/0x410 kernel/notifier.c:93
call_netdevice_notifiers_info+0xbe/0x140 net/core/dev.c:1996
call_netdevice_notifiers_extack net/core/dev.c:2034 [inline]
call_netdevice_notifiers net/core/dev.c:2048 [inline]
dev_close_many+0x333/0x6a0 net/core/dev.c:1589
page last free pid 13136 tgid 13136 stack trace:
reset_page_owner include/linux/page_owner.h:25 [inline]
free_pages_prepare mm/page_alloc.c:1108 [inline]
free_unref_page+0x5f4/0xdc0 mm/page_alloc.c:2638
stack_depot_save_flags+0x2da/0x900 lib/stackdepot.c:666
kasan_save_stack+0x42/0x60 mm/kasan/common.c:48
kasan_save_track+0x14/0x30 mm/kasan/common.c:68
unpoison_slab_object mm/kasan/common.c:319 [inline]
__kasan_slab_alloc+0x89/0x90 mm/kasan/common.c:345
kasan_slab_alloc include/linux/kasan.h:247 [inline]
slab_post_alloc_hook mm/slub.c:4085 [inline]
slab_alloc_node mm/slub.c:4134 [inline]
kmem_cache_alloc_noprof+0x121/0x2f0 mm/slub.c:4141
skb_clone+0x190/0x3f0 net/core/skbuff.c:2084
do_one_broadcast net/netlink/af_netlink.c:1462 [inline]
netlink_broadcast_filtered+0xb11/0xef0 net/netlink/af_netlink.c:1540
netlink_broadcast+0x39/0x50 net/netlink/af_netlink.c:1564
uevent_net_broadcast_untagged lib/kobject_uevent.c:331 [inline]
kobject_uevent_net_broadcast lib/kobject_uevent.c:410 [inline]
kobject_uevent_env+0xacd/0x1670 lib/kobject_uevent.c:608
device_del+0x623/0x9f0 drivers/base/core.c:3882
snd_card_disconnect.part.0+0x58a/0x7c0 sound/core/init.c:546
snd_card_disconnect+0x1f/0x30 sound/core/init.c:495
snd_usx2y_disconnect+0xe9/0x1f0 sound/usb/usx2y/usbusx2y.c:417
usb_unbind_interface+0x1e8/0x970 drivers/usb/core/driver.c:461
device_remove drivers/base/dd.c:569 [inline]
device_remove+0x122/0x170 drivers/base/dd.c:561
That's because 'subflow' is used just after 'mptcp_close_ssk(subflow)',
which will initiate the release of its memory. Even if it is very likely
the release and the re-utilisation will be done later on, it is of
course better to avoid any issues and read the content of 'subflow'
before closing it.
Fixes: 1c1f72137598 ("mptcp: pm: only decrement add_addr_accepted for MPJ req")
Cc: stable@vger.kernel.org
Reported-by: syzbot+3c8b7a8e7df6a2a226ca@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/670d7337.050a0220.4cbc0.004f.GAE@google.com
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/20241015-net-mptcp-uaf-pm-rm-v1-1-c4ee5d987a64@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Syzkaller reported a lockdep splat:
============================================
WARNING: possible recursive locking detected
6.11.0-rc6-syzkaller-00019-g67784a74e258 #0 Not tainted
--------------------------------------------
syz-executor364/5113 is trying to acquire lock:
ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328
but task is already holding lock:
ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(k-slock-AF_INET);
lock(k-slock-AF_INET);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by syz-executor364/5113:
#0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline]
#0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0x153/0x1b10 net/mptcp/protocol.c:1806
#1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline]
#1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg_fastopen+0x11f/0x530 net/mptcp/protocol.c:1727
#2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline]
#2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline]
#2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x5f/0x1b80 net/ipv4/ip_output.c:470
#3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline]
#3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline]
#3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x45f/0x1390 net/ipv4/ip_output.c:228
#4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: local_lock_acquire include/linux/local_lock_internal.h:29 [inline]
#4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: process_backlog+0x33b/0x15b0 net/core/dev.c:6104
#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline]
#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline]
#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0x230/0x5f0 net/ipv4/ip_input.c:232
#6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
#6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328
stack backtrace:
CPU: 0 UID: 0 PID: 5113 Comm: syz-executor364 Not tainted 6.11.0-rc6-syzkaller-00019-g67784a74e258 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:93 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119
check_deadlock kernel/locking/lockdep.c:3061 [inline]
validate_chain+0x15d3/0x5900 kernel/locking/lockdep.c:3855
__lock_acquire+0x137a/0x2040 kernel/locking/lockdep.c:5142
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5759
__raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline]
_raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154
spin_lock include/linux/spinlock.h:351 [inline]
sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328
mptcp_sk_clone_init+0x32/0x13c0 net/mptcp/protocol.c:3279
subflow_syn_recv_sock+0x931/0x1920 net/mptcp/subflow.c:874
tcp_check_req+0xfe4/0x1a20 net/ipv4/tcp_minisocks.c:853
tcp_v4_rcv+0x1c3e/0x37f0 net/ipv4/tcp_ipv4.c:2267
ip_protocol_deliver_rcu+0x22e/0x440 net/ipv4/ip_input.c:205
ip_local_deliver_finish+0x341/0x5f0 net/ipv4/ip_input.c:233
NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314
NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314
__netif_receive_skb_one_core net/core/dev.c:5661 [inline]
__netif_receive_skb+0x2bf/0x650 net/core/dev.c:5775
process_backlog+0x662/0x15b0 net/core/dev.c:6108
__napi_poll+0xcb/0x490 net/core/dev.c:6772
napi_poll net/core/dev.c:6841 [inline]
net_rx_action+0x89b/0x1240 net/core/dev.c:6963
handle_softirqs+0x2c4/0x970 kernel/softirq.c:554
do_softirq+0x11b/0x1e0 kernel/softirq.c:455
</IRQ>
<TASK>
__local_bh_enable_ip+0x1bb/0x200 kernel/softirq.c:382
local_bh_enable include/linux/bottom_half.h:33 [inline]
rcu_read_unlock_bh include/linux/rcupdate.h:908 [inline]
__dev_queue_xmit+0x1763/0x3e90 net/core/dev.c:4450
dev_queue_xmit include/linux/netdevice.h:3105 [inline]
neigh_hh_output include/net/neighbour.h:526 [inline]
neigh_output include/net/neighbour.h:540 [inline]
ip_finish_output2+0xd41/0x1390 net/ipv4/ip_output.c:235
ip_local_out net/ipv4/ip_output.c:129 [inline]
__ip_queue_xmit+0x118c/0x1b80 net/ipv4/ip_output.c:535
__tcp_transmit_skb+0x2544/0x3b30 net/ipv4/tcp_output.c:1466
tcp_rcv_synsent_state_process net/ipv4/tcp_input.c:6542 [inline]
tcp_rcv_state_process+0x2c32/0x4570 net/ipv4/tcp_input.c:6729
tcp_v4_do_rcv+0x77d/0xc70 net/ipv4/tcp_ipv4.c:1934
sk_backlog_rcv include/net/sock.h:1111 [inline]
__release_sock+0x214/0x350 net/core/sock.c:3004
release_sock+0x61/0x1f0 net/core/sock.c:3558
mptcp_sendmsg_fastopen+0x1ad/0x530 net/mptcp/protocol.c:1733
mptcp_sendmsg+0x1884/0x1b10 net/mptcp/protocol.c:1812
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x1a6/0x270 net/socket.c:745
____sys_sendmsg+0x525/0x7d0 net/socket.c:2597
___sys_sendmsg net/socket.c:2651 [inline]
__sys_sendmmsg+0x3b2/0x740 net/socket.c:2737
__do_sys_sendmmsg net/socket.c:2766 [inline]
__se_sys_sendmmsg net/socket.c:2763 [inline]
__x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2763
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f04fb13a6b9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 01 1a 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffd651f42d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f04fb13a6b9
RDX: 0000000000000001 RSI: 0000000020000d00 RDI: 0000000000000004
RBP: 00007ffd651f4310 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000020000080 R11: 0000000000000246 R12: 00000000000f4240
R13: 00007f04fb187449 R14: 00007ffd651f42f4 R15: 00007ffd651f4300
</TASK>
As noted by Cong Wang, the splat is false positive, but the code
path leading to the report is an unexpected one: a client is
attempting an MPC handshake towards the in-kernel listener created
by the in-kernel PM for a port based signal endpoint.
Such connection will be never accepted; many of them can make the
listener queue full and preventing the creation of MPJ subflow via
such listener - its intended role.
Explicitly detect this scenario at initial-syn time and drop the
incoming MPC request.
Fixes: 1729cf186d8a ("mptcp: create the listening socket for new port")
Cc: stable@vger.kernel.org
Reported-by: syzbot+f4aacdfef2c6a6529c3e@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f4aacdfef2c6a6529c3e
Cc: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241014-net-mptcp-mpc-port-endp-v2-1-7faea8e6b6ae@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc3).
No conflicts and no adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a previous fix, the in-kernel path-manager has been modified not to
retrigger the removal of a subflow if it was already closed, e.g. when
the initial subflow is removed, but kept in the subflows list.
To be complete, this fix should also skip the subflows that are in any
closing state: mptcp_close_ssk() will initiate the closure, but the
switch to the TCP_CLOSE state depends on the other peer.
Fixes: 58e1b66b4e4b ("mptcp: pm: do not remove already closed subflows")
Cc: stable@vger.kernel.org
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241008-net-mptcp-fallback-fixes-v1-4-c6fb8e93e551@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As reported by Christoph [1], before this patch, an MPTCP connection was
wrongly reset when a host received a first data packet with MPTCP
options after the 3wHS, but got the next ones without.
According to the MPTCP v1 specs [2], a fallback should happen in this
case, because the host didn't receive a DATA_ACK from the other peer,
nor receive data for more than the initial window which implies a
DATA_ACK being received by the other peer.
The patch here re-uses the same logic as the one used in other places:
by looking at allow_infinite_fallback, which is disabled at the creation
of an additional subflow. It's not looking at the first DATA_ACK (or
implying one received from the other side) as suggested by the RFC, but
it is in continuation with what was already done, which is safer, and it
fixes the reported issue. The next step, looking at this first DATA_ACK,
is tracked in [4].
This patch has been validated using the following Packetdrill script:
0 socket(..., SOCK_STREAM, IPPROTO_MPTCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
// 3WHS is OK
+0.0 < S 0:0(0) win 65535 <mss 1460, sackOK, nop, nop, nop, wscale 6, mpcapable v1 flags[flag_h] nokey>
+0.0 > S. 0:0(0) ack 1 <mss 1460, nop, nop, sackOK, nop, wscale 8, mpcapable v1 flags[flag_h] key[skey]>
+0.1 < . 1:1(0) ack 1 win 2048 <mpcapable v1 flags[flag_h] key[ckey=2, skey]>
+0 accept(3, ..., ...) = 4
// Data from the client with valid MPTCP options (no DATA_ACK: normal)
+0.1 < P. 1:501(500) ack 1 win 2048 <mpcapable v1 flags[flag_h] key[skey, ckey] mpcdatalen 500, nop, nop>
// From here, the MPTCP options will be dropped by a middlebox
+0.0 > . 1:1(0) ack 501 <dss dack8=501 dll=0 nocs>
+0.1 read(4, ..., 500) = 500
+0 write(4, ..., 100) = 100
// The server replies with data, still thinking MPTCP is being used
+0.0 > P. 1:101(100) ack 501 <dss dack8=501 dsn8=1 ssn=1 dll=100 nocs, nop, nop>
// But the client already did a fallback to TCP, because the two previous packets have been received without MPTCP options
+0.1 < . 501:501(0) ack 101 win 2048
+0.0 < P. 501:601(100) ack 101 win 2048
// The server should fallback to TCP, not reset: it didn't get a DATA_ACK, nor data for more than the initial window
+0.0 > . 101:101(0) ack 601
Note that this script requires Packetdrill with MPTCP support, see [3].
Fixes: dea2b1ea9c70 ("mptcp: do not reset MP_CAPABLE subflow on mapping errors")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/518 [1]
Link: https://datatracker.ietf.org/doc/html/rfc8684#name-fallback [2]
Link: https://github.com/multipath-tcp/packetdrill [3]
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/519 [4]
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241008-net-mptcp-fallback-fixes-v1-3-c6fb8e93e551@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Bugged peer implementation can send corrupted DSS options, consistently
hitting a few warning in the data path. Use DEBUG_NET assertions, to
avoid the splat on some builds and handle consistently the error, dumping
related MIBs and performing fallback and/or reset according to the
subflow type.
Fixes: 6771bfd9ee24 ("mptcp: update mptcp ack sequence from work queue")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241008-net-mptcp-fallback-fixes-v1-1-c6fb8e93e551@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
delack timer is not stopped from inet_csk_clear_xmit_timer()
because we do not define INET_CSK_CLEAR_TIMERS.
This is a conscious choice : inet_csk_clear_xmit_timer()
is often called from another cpu. Calling del_timer()
would cause false sharing and lock contention.
This means that very often, tcp_delack_timer() is called
at the timer expiration, while there is no ACK to transmit.
This can be detected very early, avoiding the socket spinlock.
Notes:
- test about tp->compressed_ack is racy,
but in the unlikely case there is a race, the dedicated
compressed_ack_timer hrtimer would close it.
- Even if the fast path is not taken, reading
icsk->icsk_ack.pending and tp->compressed_ack
before acquiring the socket spinlock reduces
acquisition time and chances of contention.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241002173042.917928-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb227 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb04 ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are two paths to access mptcp_pm_del_add_timer, result in a race
condition:
CPU1 CPU2
==== ====
net_rx_action
napi_poll netlink_sendmsg
__napi_poll netlink_unicast
process_backlog netlink_unicast_kernel
__netif_receive_skb genl_rcv
__netif_receive_skb_one_core netlink_rcv_skb
NF_HOOK genl_rcv_msg
ip_local_deliver_finish genl_family_rcv_msg
ip_protocol_deliver_rcu genl_family_rcv_msg_doit
tcp_v4_rcv mptcp_pm_nl_flush_addrs_doit
tcp_v4_do_rcv mptcp_nl_remove_addrs_list
tcp_rcv_established mptcp_pm_remove_addrs_and_subflows
tcp_data_queue remove_anno_list_by_saddr
mptcp_incoming_options mptcp_pm_del_add_timer
mptcp_pm_del_add_timer kfree(entry)
In remove_anno_list_by_saddr(running on CPU2), after leaving the critical
zone protected by "pm.lock", the entry will be released, which leads to the
occurrence of uaf in the mptcp_pm_del_add_timer(running on CPU1).
Keeping a reference to add_timer inside the lock, and calling
sk_stop_timer_sync() with this reference, instead of "entry->add_timer".
Move list_del(&entry->list) to mptcp_pm_del_add_timer and inside the pm lock,
do not directly access any members of the entry outside the pm lock, which
can avoid similar "entry->x" uaf.
Fixes: 00cfd77b9063 ("mptcp: retransmit ADD_ADDR when timeout")
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+f3a31fb909db9b2a5c4d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f3a31fb909db9b2a5c4d
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/tencent_7142963A37944B4A74EF76CD66EA3C253609@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An MPTCP firewall blackhole can be detected if the following SYN
retransmission after a fallback to "plain" TCP is accepted.
In case of blackhole, a similar technique to the one in place with TFO
is now used: MPTCP can be disabled for a certain period of time, 1h by
default. This time period will grow exponentially when more blackhole
issues get detected right after MPTCP is re-enabled and will reset to
the initial value when the blackhole issue goes away.
The blackhole period can be modified thanks to a new sysctl knob:
blackhole_timeout. Two new MIB counters help understanding what's
happening:
- 'Blackhole', incremented when a blackhole is detected.
- 'MPCapableSYNTXDisabled', incremented when an MPTCP connection
directly falls back to TCP during the blackhole period.
Because the technique is inspired by the one used by TFO, an important
part of the new code is similar to what can find in tcp_fastopen.c, with
some adaptations to the MPTCP case.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/57
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240909-net-next-mptcp-fallback-x-mpc-v1-3-da7ebb4cd2a3@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some middleboxes might be nasty with MPTCP, and decide to drop packets
with MPTCP options, instead of just dropping the MPTCP options (or
letting them pass...).
In this case, it sounds better to fallback to "plain" TCP after 2
retransmissions, and try again.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/477
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240909-net-next-mptcp-fallback-x-mpc-v1-2-da7ebb4cd2a3@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This helper will be used outside protocol.h in the following commit.
While at it, also add a 'pr_fallback()' debug print, to help identifying
fallbacks.
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240909-net-next-mptcp-fallback-x-mpc-v1-1-da7ebb4cd2a3@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recently, a few issues have been discovered around the creation of
additional subflows. Without these counters, it was difficult to point
out the reason why some subflows were not created as expected.
These counters should have been added earlier, because there is no other
simple ways to extract such information from the kernel, and understand
why subflows have not been created.
While at it, some pr_debug() have been added, just in case the errno
needs to be printed.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/509
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-3-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
__mptcp_subflow_connect() is currently called from the path-managers,
which have all the required information to create subflows. No need to
call the PM again to re-iterate over the list of entries with RCU lock
to get more info.
Instead, it is possible to pass a mptcp_pm_addr_entry structure, instead
of a mptcp_addr_info one. The former contains the ifindex and the flags
that are required when creating the new subflow.
This is a partial revert of commit ee285257a9c1 ("mptcp: drop flags and
ifindex arguments").
While at it, the local ID can also be set if it is known and 0, to avoid
having to set it in the 'rebuild_header' hook, which will cause a new
iteration of the endpoint entries.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-2-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename all the helpers specific to the flushing operations to make it
clear that the intention is to flush all created subflows, and remove
all announced addresses, not just a specific selection.
That way, it is easier to understand why the id_avail_bitmap and
local_addr_used are reset at the end.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-1-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/faraday/ftgmac100.c
4186c8d9e6af ("net: ftgmac100: Ensure tx descriptor updates are visible")
e24a6c874601 ("net: ftgmac100: Get link speed and duplex for NC-SI")
https://lore.kernel.org/0b851ec5-f91d-4dd3-99da-e81b98c9ed28@kernel.org
net/ipv4/tcp.c
bac76cf89816 ("tcp: fix forever orphan socket caused by tcp_abort")
edefba66d929 ("tcp: rstreason: introduce SK_RST_REASON_TCP_STATE for active reset")
https://lore.kernel.org/20240828112207.5c199d41@canb.auug.org.au
No adjacent changes.
Link: https://patch.msgid.link/20240829130829.39148-1-pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ADD_ADDR 0 with the address from the initial subflow should not be
considered as a new address: this is not something new. If the host
receives it, it simply means that the address is available again.
When receiving an ADD_ADDR for the ID 0, the PM already doesn't consider
it as new by not incrementing the 'add_addr_accepted' counter. But the
'accept_addr' might not be set if the limit has already been reached:
this can be bypassed in this case. But before, it is important to check
that this ADD_ADDR for the ID 0 is for the same address as the initial
subflow. If not, it is not something that should happen, and the
ADD_ADDR can be ignored.
Note that if an ADD_ADDR is received while there is already a subflow
opened using the same address, this ADD_ADDR is ignored as well. It
means that if multiple ADD_ADDR for ID 0 are received, there will not be
any duplicated subflows created by the client.
Fixes: d0876b2284cf ("mptcp: add the incoming RM_ADDR support")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The initial subflow might have already been closed, but still in the
connection list. When the worker is instructed to close the subflows
that have been marked as closed, it might then try to close the initial
subflow again.
A consequence of that is that the SUB_CLOSED event can be seen twice:
# ip mptcp endpoint
1.1.1.1 id 1 subflow dev eth0
2.2.2.2 id 2 subflow dev eth1
# ip mptcp monitor &
[ CREATED] remid=0 locid=0 saddr4=1.1.1.1 daddr4=9.9.9.9
[ ESTABLISHED] remid=0 locid=0 saddr4=1.1.1.1 daddr4=9.9.9.9
[ SF_ESTABLISHED] remid=0 locid=2 saddr4=2.2.2.2 daddr4=9.9.9.9
# ip mptcp endpoint delete id 1
[ SF_CLOSED] remid=0 locid=0 saddr4=1.1.1.1 daddr4=9.9.9.9
[ SF_CLOSED] remid=0 locid=0 saddr4=1.1.1.1 daddr4=9.9.9.9
The first one is coming from mptcp_pm_nl_rm_subflow_received(), and the
second one from __mptcp_close_subflow().
To avoid doing the post-closed processing twice, the subflow is now
marked as closed the first time.
Note that it is not enough to check if we are dealing with the first
subflow and check its sk_state: the subflow might have been reset or
closed before calling mptcp_close_ssk().
Fixes: b911c97c7dc7 ("mptcp: add netlink event support")
Cc: stable@vger.kernel.org
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
'local_addr_used' and 'add_addr_accepted' are decremented for addresses
not related to the initial subflow (ID0), because the source and
destination addresses of the initial subflows are known from the
beginning: they don't count as "additional local address being used" or
"ADD_ADDR being accepted".
It is then required not to increment them when the entrypoint used by
the initial subflow is removed and re-added during a connection. Without
this modification, this entrypoint cannot be removed and re-added more
than once.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/512
Fixes: 3ad14f54bd74 ("mptcp: more accurate MPC endpoint tracking")
Reported-by: syzbot+455d38ecd5f655fc45cf@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/00000000000049861306209237f4@google.com
Cc: stable@vger.kernel.org
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It is possible to have in the list already closed subflows, e.g. the
initial subflow has been already closed, but still in the list. No need
to try to close it again, and increments the related counters again.
Fixes: 0ee4261a3681 ("mptcp: implement mptcp_pm_remove_subflow")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The initial subflow has a special local ID: 0. It is specific per
connection.
When a global endpoint is deleted and re-added later, it can have a
different ID -- most services managing the endpoints automatically don't
force the ID to be the same as before. It is then important to track
these modifications to be consistent with the ID being used for the
address used by the initial subflow, not to confuse the other peer or to
send the ID 0 for the wrong address.
Now when removing an endpoint, msk->mpc_endpoint_id is reset if it
corresponds to this endpoint. When adding a new endpoint, the same
variable is updated if the address match the one of the initial subflow.
Fixes: 3ad14f54bd74 ("mptcp: more accurate MPC endpoint tracking")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The lookup_subflow_by_daddr() helper checks if there is already a
subflow connected to this address. But there could be a subflow that is
closing, but taking time due to some reasons: latency, losses, data to
process, etc.
If an ADD_ADDR is received while the endpoint is being closed, it is
better to try connecting to it, instead of rejecting it: the peer which
has sent the ADD_ADDR will not be notified that the ADD_ADDR has been
rejected for this reason, and the expected subflow will not be created
at the end.
This helper should then only look for subflows that are established, or
going to be, but not the ones being closed.
Fixes: d84ad04941c3 ("mptcp: skip connecting the connected address")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Taking the first one on the list doesn't work in some cases, e.g. if the
initial subflow is being removed. Pick another one instead of not
sending anything.
Fixes: 84dfe3677a6f ("mptcp: send out dedicated ADD_ADDR packet")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The initial subflow has a special local ID: 0. When an endpoint is being
deleted, it is then important to check if its address is not linked to
the initial subflow to send the right ID.
If there was an endpoint linked to the initial subflow, msk's
mpc_endpoint_id field will be set. We can then use this info when an
endpoint is being removed to see if it is linked to the initial subflow.
So now, the correct IDs are passed to mptcp_pm_nl_rm_addr_or_subflow(),
it is no longer needed to use mptcp_local_id_match().
Fixes: 3ad14f54bd74 ("mptcp: more accurate MPC endpoint tracking")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When the endpoint used by the initial subflow is removed and re-added
later, the PM has to force the ID 0, it is a special case imposed by the
MPTCP specs.
Note that the endpoint should then need to be re-added reusing the same
ID.
Fixes: 3ad14f54bd74 ("mptcp: more accurate MPC endpoint tracking")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
pr_debug() have been added in various places in MPTCP code to help
developers to debug some situations. With the dynamic debug feature, it
is easy to enable all or some of them, and asks users to reproduce
issues with extra debug.
Many of these pr_debug() don't end with a new line, while no 'pr_cont()'
are used in MPTCP code. So the goal was not to display multiple debug
messages on one line: they were then not missing the '\n' on purpose.
Not having the new line at the end causes these messages to be printed
with a delay, when something else needs to be printed. This issue is not
visible when many messages need to be printed, but it is annoying and
confusing when only specific messages are expected, e.g.
# echo "func mptcp_pm_add_addr_echoed +fmp" \
> /sys/kernel/debug/dynamic_debug/control
# ./mptcp_join.sh "signal address"; \
echo "$(awk '{print $1}' /proc/uptime) - end"; \
sleep 5s; \
echo "$(awk '{print $1}' /proc/uptime) - restart"; \
./mptcp_join.sh "signal address"
013 signal address
(...)
10.75 - end
15.76 - restart
013 signal address
[ 10.367935] mptcp:mptcp_pm_add_addr_echoed: MPTCP: msk=(...)
(...)
=> a delay of 5 seconds: printed with a 10.36 ts, but after 'restart'
which was printed at the 15.76 ts.
The 'Fixes' tag here below points to the first pr_debug() used without
'\n' in net/mptcp. This patch could be split in many small ones, with
different Fixes tag, but it doesn't seem worth it, because it is easy to
re-generate this patch with this simple 'sed' command:
git grep -l pr_debug -- net/mptcp |
xargs sed -i "s/\(pr_debug(\".*[^n]\)\(\"[,)]\)/\1\\\n\2/g"
So in case of conflicts, simply drop the modifications, and launch this
command.
Fixes: f870fa0b5768 ("mptcp: Add MPTCP socket stubs")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240826-net-mptcp-close-extra-sf-fin-v1-4-905199fe1172@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 'mptcp_subflow_context' structure has two items related to the
backup flags:
- 'backup': the subflow has been marked as backup by the other peer
- 'request_bkup': the backup flag has been set by the host
Looking only at the 'backup' flag can make sense in some cases, but it
is not the behaviour of the default packet scheduler when selecting
paths.
As explained in the commit b6a66e521a20 ("mptcp: sched: check both
directions for backup"), the packet scheduler should look at both flags,
because that was the behaviour from the beginning: the 'backup' flag was
set by accident instead of the 'request_bkup' one. Now that the latter
has been fixed, get_retrans() needs to be adapted as well.
Fixes: b6a66e521a20 ("mptcp: sched: check both directions for backup")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240826-net-mptcp-close-extra-sf-fin-v1-3-905199fe1172@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|