diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 15 |
1 files changed, 7 insertions, 8 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index c42c4a820b89..2c9d3c719d8a 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -494,7 +494,6 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame. * Use together with %RX_FLAG_MMIC_STRIPPED. * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware. - * @RX_FLAG_RADIOTAP: This frame starts with a radiotap header. * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame, * verification has been done by the hardware. * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame. @@ -515,7 +514,6 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR = 1<<0, RX_FLAG_DECRYPTED = 1<<1, - RX_FLAG_RADIOTAP = 1<<2, RX_FLAG_MMIC_STRIPPED = 1<<3, RX_FLAG_IV_STRIPPED = 1<<4, RX_FLAG_FAILED_FCS_CRC = 1<<5, @@ -565,7 +563,9 @@ struct ieee80211_rx_status { * * Flags to define PHY configuration options * - * @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported) + * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this + * to determine for example whether to calculate timestamps for packets + * or not, do not use instead of filter flags! * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only) * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set * the driver should be prepared to handle configuration requests but @@ -574,7 +574,7 @@ struct ieee80211_rx_status { * it can also be unset in that case when monitor interfaces are active. */ enum ieee80211_conf_flags { - IEEE80211_CONF_RADIOTAP = (1<<0), + IEEE80211_CONF_MONITOR = (1<<0), IEEE80211_CONF_PS = (1<<1), IEEE80211_CONF_IDLE = (1<<2), }; @@ -584,7 +584,7 @@ enum ieee80211_conf_flags { * enum ieee80211_conf_changed - denotes which configuration changed * * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed - * @IEEE80211_CONF_CHANGE_RADIOTAP: the radiotap flag changed + * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed * @IEEE80211_CONF_CHANGE_POWER: the TX power changed * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed @@ -593,7 +593,7 @@ enum ieee80211_conf_flags { */ enum ieee80211_conf_changed { IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2), - IEEE80211_CONF_CHANGE_RADIOTAP = BIT(3), + IEEE80211_CONF_CHANGE_MONITOR = BIT(3), IEEE80211_CONF_CHANGE_PS = BIT(4), IEEE80211_CONF_CHANGE_POWER = BIT(5), IEEE80211_CONF_CHANGE_CHANNEL = BIT(6), @@ -1661,8 +1661,7 @@ void ieee80211_restart_hw(struct ieee80211_hw *hw); * ieee80211_rx - receive frame * * Use this function to hand received frames to mac80211. The receive - * buffer in @skb must start with an IEEE 802.11 header or a radiotap - * header if %RX_FLAG_RADIOTAP is set in the @status flags. + * buffer in @skb must start with an IEEE 802.11 header. * * This function may not be called in IRQ context. Calls to this function * for a single hardware must be synchronized against each other. Calls to |