diff options
Diffstat (limited to 'drivers/leds/Kconfig')
| -rw-r--r-- | drivers/leds/Kconfig | 101 |
1 files changed, 1 insertions, 100 deletions
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig index c7f755034375..d44806d41b44 100644 --- a/drivers/leds/Kconfig +++ b/drivers/leds/Kconfig @@ -479,106 +479,7 @@ config LEDS_BLINKM This option enables support for the BlinkM RGB LED connected through I2C. Say Y to enable support for the BlinkM LED. -config LEDS_TRIGGERS - bool "LED Trigger support" - depends on LEDS_CLASS - help - This option enables trigger support for the leds class. - These triggers allow kernel events to drive the LEDs and can - be configured via sysfs. If unsure, say Y. - comment "LED Triggers" - -config LEDS_TRIGGER_TIMER - tristate "LED Timer Trigger" - depends on LEDS_TRIGGERS - help - This allows LEDs to be controlled by a programmable timer - via sysfs. Some LED hardware can be programmed to start - blinking the LED without any further software interaction. - For more details read Documentation/leds/leds-class.txt. - - If unsure, say Y. - -config LEDS_TRIGGER_ONESHOT - tristate "LED One-shot Trigger" - depends on LEDS_TRIGGERS - help - This allows LEDs to blink in one-shot pulses with parameters - controlled via sysfs. It's useful to notify the user on - sporadic events, when there are no clear begin and end trap points, - or on dense events, where this blinks the LED at constant rate if - rearmed continuously. - - It also shows how to use the led_blink_set_oneshot() function. - - If unsure, say Y. - -config LEDS_TRIGGER_IDE_DISK - bool "LED IDE Disk Trigger" - depends on IDE_GD_ATA - depends on LEDS_TRIGGERS - help - This allows LEDs to be controlled by IDE disk activity. - If unsure, say Y. - -config LEDS_TRIGGER_HEARTBEAT - tristate "LED Heartbeat Trigger" - depends on LEDS_TRIGGERS - help - This allows LEDs to be controlled by a CPU load average. - The flash frequency is a hyperbolic function of the 1-minute - load average. - If unsure, say Y. - -config LEDS_TRIGGER_BACKLIGHT - tristate "LED backlight Trigger" - depends on LEDS_TRIGGERS - help - This allows LEDs to be controlled as a backlight device: they - turn off and on when the display is blanked and unblanked. - - If unsure, say N. - -config LEDS_TRIGGER_CPU - bool "LED CPU Trigger" - depends on LEDS_TRIGGERS - help - This allows LEDs to be controlled by active CPUs. This shows - the active CPUs across an array of LEDs so you can see which - CPUs are active on the system at any given moment. - - If unsure, say N. - -config LEDS_TRIGGER_GPIO - tristate "LED GPIO Trigger" - depends on LEDS_TRIGGERS - depends on GPIOLIB - help - This allows LEDs to be controlled by gpio events. It's good - when using gpios as switches and triggering the needed LEDs - from there. One use case is n810's keypad LEDs that could - be triggered by this trigger when user slides up to show - keypad. - - If unsure, say N. - -config LEDS_TRIGGER_DEFAULT_ON - tristate "LED Default ON Trigger" - depends on LEDS_TRIGGERS - help - This allows LEDs to be initialised in the ON state. - If unsure, say Y. - -comment "iptables trigger is under Netfilter config (LED target)" - depends on LEDS_TRIGGERS - -config LEDS_TRIGGER_TRANSIENT - tristate "LED Transient Trigger" - depends on LEDS_TRIGGERS - help - This allows one time activation of a transient state on - GPIO/PWM based hardware. - If unsure, say Y. +source "drivers/leds/trigger/Kconfig" endif # NEW_LEDS |