diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml | 190 |
1 files changed, 190 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml b/Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml new file mode 100644 index 000000000000..d7f20b8518e0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/frequency/adi,adf4350.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/frequency/adi,adf4350.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADF4350/ADF4351 wideband synthesizer + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + +properties: + compatible: + enum: + - adi,adf4350 + - adi,adf4351 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 20000000 + + clocks: + maxItems: 1 + description: Clock to provide CLKIN reference clock signal. + + clock-names: + const: clkin + + gpios: + maxItems: 1 + description: Lock detect GPIO. + + adi,channel-spacing: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Channel spacing in Hz (influences MODULUS). + + adi,power-up-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + If set the PLL tunes to this frequency (in Hz) on driver probe. + + adi,reference-div-factor: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + If set the driver skips dynamic calculation and uses this default + value instead. + + adi,reference-doubler-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables reference doubler. + + adi,reference-div2-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables reference divider. + + adi,phase-detector-polarity-positive-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables positive phase detector polarity. Default negative. + + adi,lock-detect-precision-6ns-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables 6ns lock detect precision. Default = 10ns. + + adi,lock-detect-function-integer-n-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enables lock detect for integer-N mode. Default = factional-N mode. + + adi,charge-pump-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Charge pump current in mA. Default = 2500mA. + + adi,muxout-select: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 6 + description: | + On chip multiplexer output selection. + Valid values for the multiplexer output are: + 0: Three-State Output (default) + 1: DVDD + 2: DGND + 3: R-Counter output + 4: N-Divider output + 5: Analog lock detect + 6: Digital lock detect + + adi,low-spur-mode-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables low spur mode. Default = Low noise mode. + + adi,cycle-slip-reduction-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables cycle slip reduction. + + adi,charge-cancellation-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enabled charge pump charge cancellation for integer-N modes. + + adi,anti-backlash-3ns-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enables 3ns antibacklash pulse width for integer-N modes. + + adi,band-select-clock-mode-high-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables faster band selection logic. + + adi,12bit-clk-divider: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Clock divider value used when adi,12bit-clkdiv-mode != 0 + + adi,clk-divider-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + description: | + Valid values for the clkdiv mode are: + 0: Clock divider off (default) + 1: Fast lock enable + 2: Phase resync enable + + adi,aux-output-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables auxiliary RF output. + + adi,aux-output-fundamental-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Selects fundamental VCO output on the auxiliary RF output. + Default = Output of RF dividers. + + adi,mute-till-lock-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Enables Mute-Till-Lock-Detect function. + + adi,output-power: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + + adi,aux-output-power: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Auxiliary output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + +additionalProperties: false + +required: + - compatible + - reg + - clocks + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + pll@4 { + compatible = "adi,adf4351"; + reg = <4>; + spi-max-frequency = <10000000>; + clocks = <&clk0_ad9523 9>; + clock-names = "clkin"; + adi,channel-spacing = <10000>; + adi,power-up-frequency = <2400000000>; + adi,phase-detector-polarity-positive-enable; + adi,charge-pump-current = <2500>; + adi,output-power = <3>; + adi,mute-till-lock-enable; + }; + }; +... |