diff options
| -rw-r--r-- | arch/arm/mach-at91/Kconfig | 14 | ||||
| -rw-r--r-- | arch/arm/mach-at91/Makefile | 5 | ||||
| -rw-r--r-- | arch/arm/mach-at91/at91_tc.h | 146 | ||||
| -rw-r--r-- | arch/arm/mach-at91/at91rm9200_time.c | 23 | ||||
| -rw-r--r-- | arch/arm/mach-at91/board-dt-rm9200.c | 2 | ||||
| -rw-r--r-- | arch/arm/mach-at91/board-dt-sam9.c | 1 | ||||
| -rw-r--r-- | arch/arm/mach-at91/board.h | 123 | ||||
| -rw-r--r-- | arch/arm/mach-at91/generic.h | 33 | ||||
| -rw-r--r-- | arch/arm/mach-at91/gpio.c | 982 | ||||
| -rw-r--r-- | arch/arm/mach-at91/gpio.h | 214 | ||||
| -rw-r--r-- | arch/arm/mach-at91/gsia18s.h | 33 | ||||
| -rw-r--r-- | arch/arm/mach-at91/include/mach/hardware.h | 5 | ||||
| -rw-r--r-- | arch/arm/mach-at91/leds.c | 56 | ||||
| -rw-r--r-- | arch/arm/mach-at91/pm.c | 11 | ||||
| -rw-r--r-- | arch/arm/mach-at91/setup.c | 54 | ||||
| -rw-r--r-- | arch/arm/mach-at91/soc.h | 6 | ||||
| -rw-r--r-- | drivers/clocksource/timer-atmel-pit.c | 32 |
17 files changed, 5 insertions, 1735 deletions
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 231893d71658..2395c68b3e32 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -174,21 +174,11 @@ config SOC_AT91SAM9N12 # ---------------------------------------------------------- endif # SOC_SAM_V4_V5 -comment "Generic Board Type" - config MACH_AT91RM9200_DT - bool "Atmel AT91RM9200 Evaluation Kits with device-tree support" - depends on SOC_AT91RM9200 - help - Select this if you want to experiment device-tree with - an Atmel RM9200 Evaluation Kit. + def_bool SOC_AT91RM9200 config MACH_AT91SAM9_DT - bool "Atmel AT91SAM Evaluation Kits with device-tree support" - depends on SOC_AT91SAM9 - help - Select this if you want to experiment device-tree with - an Atmel Evaluation Kit. + def_bool SOC_AT91SAM9 # ---------------------------------------------------------- diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 2371b8845bf5..7b6424d40764 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -2,7 +2,7 @@ # Makefile for the linux kernel. # -obj-y := gpio.o setup.o sysirq_mask.o +obj-y := setup.o sysirq_mask.o obj-$(CONFIG_SOC_AT91SAM9) += sam9_smc.o @@ -25,9 +25,6 @@ obj-$(CONFIG_MACH_AT91SAM9_DT) += board-dt-sam9.o # SAMA5 board with device-tree obj-$(CONFIG_SOC_SAMA5) += board-dt-sama5.o -# Drivers -obj-y += leds.o - # Power Management obj-$(CONFIG_PM) += pm.o obj-$(CONFIG_AT91_SLOW_CLOCK) += pm_slowclock.o diff --git a/arch/arm/mach-at91/at91_tc.h b/arch/arm/mach-at91/at91_tc.h deleted file mode 100644 index 46a317fd7164..000000000000 --- a/arch/arm/mach-at91/at91_tc.h +++ /dev/null @@ -1,146 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91_tc.h - * - * Copyright (C) SAN People - * - * Timer/Counter Unit (TC) registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_TC_H -#define AT91_TC_H - -#define AT91_TC_BCR 0xc0 /* TC Block Control Register */ -#define AT91_TC_SYNC (1 << 0) /* Synchro Command */ - -#define AT91_TC_BMR 0xc4 /* TC Block Mode Register */ -#define AT91_TC_TC0XC0S (3 << 0) /* External Clock Signal 0 Selection */ -#define AT91_TC_TC0XC0S_TCLK0 (0 << 0) -#define AT91_TC_TC0XC0S_NONE (1 << 0) -#define AT91_TC_TC0XC0S_TIOA1 (2 << 0) -#define AT91_TC_TC0XC0S_TIOA2 (3 << 0) -#define AT91_TC_TC1XC1S (3 << 2) /* External Clock Signal 1 Selection */ -#define AT91_TC_TC1XC1S_TCLK1 (0 << 2) -#define AT91_TC_TC1XC1S_NONE (1 << 2) -#define AT91_TC_TC1XC1S_TIOA0 (2 << 2) -#define AT91_TC_TC1XC1S_TIOA2 (3 << 2) -#define AT91_TC_TC2XC2S (3 << 4) /* External Clock Signal 2 Selection */ -#define AT91_TC_TC2XC2S_TCLK2 (0 << 4) -#define AT91_TC_TC2XC2S_NONE (1 << 4) -#define AT91_TC_TC2XC2S_TIOA0 (2 << 4) -#define AT91_TC_TC2XC2S_TIOA1 (3 << 4) - - -#define AT91_TC_CCR 0x00 /* Channel Control Register */ -#define AT91_TC_CLKEN (1 << 0) /* Counter Clock Enable Command */ -#define AT91_TC_CLKDIS (1 << 1) /* Counter CLock Disable Command */ -#define AT91_TC_SWTRG (1 << 2) /* Software Trigger Command */ - -#define AT91_TC_CMR 0x04 /* Channel Mode Register */ -#define AT91_TC_TCCLKS (7 << 0) /* Capture/Waveform Mode: Clock Selection */ -#define AT91_TC_TIMER_CLOCK1 (0 << 0) -#define AT91_TC_TIMER_CLOCK2 (1 << 0) -#define AT91_TC_TIMER_CLOCK3 (2 << 0) -#define AT91_TC_TIMER_CLOCK4 (3 << 0) -#define AT91_TC_TIMER_CLOCK5 (4 << 0) -#define AT91_TC_XC0 (5 << 0) -#define AT91_TC_XC1 (6 << 0) -#define AT91_TC_XC2 (7 << 0) -#define AT91_TC_CLKI (1 << 3) /* Capture/Waveform Mode: Clock Invert */ -#define AT91_TC_BURST (3 << 4) /* Capture/Waveform Mode: Burst Signal Selection */ -#define AT91_TC_LDBSTOP (1 << 6) /* Capture Mode: Counter Clock Stopped with TB Loading */ -#define AT91_TC_LDBDIS (1 << 7) /* Capture Mode: Counter Clock Disable with RB Loading */ -#define AT91_TC_ETRGEDG (3 << 8) /* Capture Mode: External Trigger Edge Selection */ -#define AT91_TC_ABETRG (1 << 10) /* Capture Mode: TIOA or TIOB External Trigger Selection */ -#define AT91_TC_CPCTRG (1 << 14) /* Capture Mode: RC Compare Trigger Enable */ -#define AT91_TC_WAVE (1 << 15) /* Capture/Waveform mode */ -#define AT91_TC_LDRA (3 << 16) /* Capture Mode: RA Loading Selection */ -#define AT91_TC_LDRB (3 << 18) /* Capture Mode: RB Loading Selection */ - -#define AT91_TC_CPCSTOP (1 << 6) /* Waveform Mode: Counter Clock Stopped with RC Compare */ -#define AT91_TC_CPCDIS (1 << 7) /* Waveform Mode: Counter Clock Disable with RC Compare */ -#define AT91_TC_EEVTEDG (3 << 8) /* Waveform Mode: External Event Edge Selection */ -#define AT91_TC_EEVTEDG_NONE (0 << 8) -#define AT91_TC_EEVTEDG_RISING (1 << 8) -#define AT91_TC_EEVTEDG_FALLING (2 << 8) -#define AT91_TC_EEVTEDG_BOTH (3 << 8) -#define AT91_TC_EEVT (3 << 10) /* Waveform Mode: External Event Selection */ -#define AT91_TC_EEVT_TIOB (0 << 10) -#define AT91_TC_EEVT_XC0 (1 << 10) -#define AT91_TC_EEVT_XC1 (2 << 10) -#define AT91_TC_EEVT_XC2 (3 << 10) -#define AT91_TC_ENETRG (1 << 12) /* Waveform Mode: External Event Trigger Enable */ -#define AT91_TC_WAVESEL (3 << 13) /* Waveform Mode: Waveform Selection */ -#define AT91_TC_WAVESEL_UP (0 << 13) -#define AT91_TC_WAVESEL_UP_AUTO (2 << 13) -#define AT91_TC_WAVESEL_UPDOWN (1 << 13) -#define AT91_TC_WAVESEL_UPDOWN_AUTO (3 << 13) -#define AT91_TC_ACPA (3 << 16) /* Waveform Mode: RA Compare Effect on TIOA */ -#define AT91_TC_ACPA_NONE (0 << 16) -#define AT91_TC_ACPA_SET (1 << 16) -#define AT91_TC_ACPA_CLEAR (2 << 16) -#define AT91_TC_ACPA_TOGGLE (3 << 16) -#define AT91_TC_ACPC (3 << 18) /* Waveform Mode: RC Compre Effect on TIOA */ -#define AT91_TC_ACPC_NONE (0 << 18) -#define AT91_TC_ACPC_SET (1 << 18) -#define AT91_TC_ACPC_CLEAR (2 << 18) -#define AT91_TC_ACPC_TOGGLE (3 << 18) -#define AT91_TC_AEEVT (3 << 20) /* Waveform Mode: External Event Effect on TIOA */ -#define AT91_TC_AEEVT_NONE (0 << 20) -#define AT91_TC_AEEVT_SET (1 << 20) -#define AT91_TC_AEEVT_CLEAR (2 << 20) -#define AT91_TC_AEEVT_TOGGLE (3 << 20) -#define AT91_TC_ASWTRG (3 << 22) /* Waveform Mode: Software Trigger Effect on TIOA */ -#define AT91_TC_ASWTRG_NONE (0 << 22) -#define AT91_TC_ASWTRG_SET (1 << 22) -#define AT91_TC_ASWTRG_CLEAR (2 << 22) -#define AT91_TC_ASWTRG_TOGGLE (3 << 22) -#define AT91_TC_BCPB (3 << 24) /* Waveform Mode: RB Compare Effect on TIOB */ -#define AT91_TC_BCPB_NONE (0 << 24) -#define AT91_TC_BCPB_SET (1 << 24) -#define AT91_TC_BCPB_CLEAR (2 << 24) -#define AT91_TC_BCPB_TOGGLE (3 << 24) -#define AT91_TC_BCPC (3 << 26) /* Waveform Mode: RC Compare Effect on TIOB */ -#define AT91_TC_BCPC_NONE (0 << 26) -#define AT91_TC_BCPC_SET (1 << 26) -#define AT91_TC_BCPC_CLEAR (2 << 26) -#define AT91_TC_BCPC_TOGGLE (3 << 26) -#define AT91_TC_BEEVT (3 << 28) /* Waveform Mode: External Event Effect on TIOB */ -#define AT91_TC_BEEVT_NONE (0 << 28) -#define AT91_TC_BEEVT_SET (1 << 28) -#define AT91_TC_BEEVT_CLEAR (2 << 28) -#define AT91_TC_BEEVT_TOGGLE (3 << 28) -#define AT91_TC_BSWTRG (3 << 30) /* Waveform Mode: Software Trigger Effect on TIOB */ -#define AT91_TC_BSWTRG_NONE (0 << 30) -#define AT91_TC_BSWTRG_SET (1 << 30) -#define AT91_TC_BSWTRG_CLEAR (2 << 30) -#define AT91_TC_BSWTRG_TOGGLE (3 << 30) - -#define AT91_TC_CV 0x10 /* Counter Value */ -#define AT91_TC_RA 0x14 /* Register A */ -#define AT91_TC_RB 0x18 /* Register B */ -#define AT91_TC_RC 0x1c /* Register C */ - -#define AT91_TC_SR 0x20 /* Status Register */ -#define AT91_TC_COVFS (1 << 0) /* Counter Overflow Status */ -#define AT91_TC_LOVRS (1 << 1) /* Load Overrun Status */ -#define AT91_TC_CPAS (1 << 2) /* RA Compare Status */ -#define AT91_TC_CPBS (1 << 3) /* RB Compare Status */ -#define AT91_TC_CPCS (1 << 4) /* RC Compare Status */ -#define AT91_TC_LDRAS (1 << 5) /* RA Loading Status */ -#define AT91_TC_LDRBS (1 << 6) /* RB Loading Status */ -#define AT91_TC_ETRGS (1 << 7) /* External Trigger Status */ -#define AT91_TC_CLKSTA (1 << 16) /* Clock Enabling Status */ -#define AT91_TC_MTIOA (1 << 17) /* TIOA Mirror */ -#define AT91_TC_MTIOB (1 << 18) /* TIOB Mirror */ - -#define AT91_TC_IER 0x24 /* Interrupt Enable Register */ -#define AT91_TC_IDR 0x28 /* Interrupt Disable Register */ -#define AT91_TC_IMR 0x2c /* Interrupt Mask Register */ - -#endif diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c index 7fd13aef9827..51761f8927b7 100644 --- a/arch/arm/mach-at91/at91rm9200_time.c +++ b/arch/arm/mach-at91/at91rm9200_time.c @@ -183,7 +183,6 @@ static struct clock_event_device clkevt = { void __iomem *at91_st_base; EXPORT_SYMBOL_GPL(at91_st_base); -#ifdef CONFIG_OF static struct of_device_id at91rm9200_st_timer_ids[] = { { .compatible = "atmel,at91rm9200-st" }, { /* sentinel */ } @@ -219,28 +218,6 @@ node_err: err: return -EINVAL; } -#else -static int __init of_at91rm9200_st_init(void) -{ - return -EINVAL; -} -#endif - -void __init at91rm9200_ioremap_st(u32 addr) -{ -#ifdef CONFIG_OF - struct device_node *np; - - np = of_find_matching_node(NULL, at91rm9200_st_timer_ids); - if (np) { - of_node_put(np); - return; - } -#endif - at91_st_base = ioremap(addr, 256); - if (!at91_st_base) - panic("Impossible to ioremap ST\n"); -} /* * ST (system timer) module supports both clockevents and clocksource. diff --git a/arch/arm/mach-at91/board-dt-rm9200.c b/arch/arm/mach-at91/board-dt-rm9200.c index feeb1a0f258e..76dfe8f9af50 100644 --- a/arch/arm/mach-at91/board-dt-rm9200.c +++ b/arch/arm/mach-at91/board-dt-rm9200.c @@ -26,9 +26,7 @@ static void __init at91rm9200_dt_timer_init(void) { -#if defined(CONFIG_COMMON_CLK) of_clk_init(NULL); -#endif at91rm9200_timer_init(); } diff --git a/arch/arm/mach-at91/board-dt-sam9.c b/arch/arm/mach-at91/board-dt-sam9.c index 67c1bcbf0ed9..f99246aa9b38 100644 --- a/arch/arm/mach-at91/board-dt-sam9.c +++ b/arch/arm/mach-at91/board-dt-sam9.c @@ -21,7 +21,6 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include "board.h" #include "generic.h" static const char *at91_dt_board_compat[] __initdata = { diff --git a/arch/arm/mach-at91/board.h b/arch/arm/mach-at91/board.h deleted file mode 100644 index d268ec3781dd..000000000000 --- a/arch/arm/mach-at91/board.h +++ /dev/null @@ -1,123 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/board.h - * - * Copyright (C) 2005 HP Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -/* - * These are data structures found in platform_device.dev.platform_data, - * and describing board-specific data needed by drivers. For example, - * which pin is used for a given GPIO role. - * - * In 2.6, drivers should strongly avoid board-specific knowledge so - * that supporting new boards normally won't require driver patches. - * Most board-specific knowledge should be in arch/.../board-*.c files. - */ - -#ifndef __ASM_ARCH_BOARD_H -#define __ASM_ARCH_BOARD_H - -#include <linux/platform_data/atmel.h> - - /* USB Device */ -extern void __init at91_add_device_udc(struct at91_udc_data *data); - - /* USB High Speed Device */ -extern void __init at91_add_device_usba(struct usba_platform_data *data); - - /* Compact Flash */ -extern void __init at91_add_device_cf(struct at91_cf_data *data); - - /* MMC / SD */ - /* atmel-mci platform config */ -extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data); - -extern void __init at91_add_device_eth(struct macb_platform_data *data); - - /* USB Host */ -extern void __init at91_add_device_usbh(struct at91_usbh_data *data); -extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data); -extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data); - -extern void __init at91_add_device_nand(struct atmel_nand_data *data); - - /* I2C*/ -extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices); - - /* SPI */ -extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices); - - /* Serial */ -#define ATMEL_UART_CTS 0x01 -#define ATMEL_UART_RTS 0x02 -#define ATMEL_UART_DSR 0x04 -#define ATMEL_UART_DTR 0x08 -#define ATMEL_UART_DCD 0x10 -#define ATMEL_UART_RI 0x20 - -extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins); - -extern struct platform_device *atmel_default_console_device; - -extern void __init at91_add_device_serial(void); - -/* - * PWM - */ -#define AT91_PWM0 0 -#define AT91_PWM1 1 -#define AT91_PWM2 2 -#define AT91_PWM3 3 - -extern void __init at91_add_device_pwm(u32 mask); - -/* - * SSC -- accessed through ssc_request(id). Drivers don't bind to SSC - * platform devices. Their SSC ID is part of their configuration data, - * along with information about which SSC signals they should use. - */ -#define ATMEL_SSC_TK 0x01 -#define ATMEL_SSC_TF 0x02 -#define ATMEL_SSC_TD 0x04 -#define ATMEL_SSC_TX (ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD) - -#define ATMEL_SSC_RK 0x10 -#define ATMEL_SSC_RF 0x20 -#define ATMEL_SSC_RD 0x40 -#define ATMEL_SSC_RX (ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD) - -extern void __init at91_add_device_ssc(unsigned id, unsigned pins); - - /* LCD Controller */ -struct atmel_lcdfb_pdata; -extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data); - - /* AC97 */ -extern void __init at91_add_device_ac97(struct ac97c_platform_data *data); - - /* ISI */ -struct isi_platform_data; -extern void __init at91_add_device_isi(struct isi_platform_data *data, - bool use_pck_as_mck); - -/* CAN */ -extern void __init at91_add_device_can(struct at91_can_data *data); - - /* LEDs */ -extern void __init at91_gpio_leds(struct gpio_led *leds, int nr); - -#endif diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h index eb81940f9848..d53324210adf 100644 --- a/arch/arm/mach-at91/generic.h +++ b/arch/arm/mach-at91/generic.h @@ -22,52 +22,19 @@ extern void __init at91_init_sram(int bank, unsigned long base, /* Processors */ extern void __init at91rm9200_set_type(int type); -extern void __init at91_initialize(unsigned long main_clock); extern void __init at91rm9200_dt_initialize(void); extern void __init at91_dt_initialize(void); /* Interrupts */ -extern void __init at91_init_irq_default(void); -extern void __init at91_init_interrupts(unsigned int priority[]); extern void __init at91_sysirq_mask_rtc(u32 rtc_base); extern void __init at91_sysirq_mask_rtt(u32 rtt_base); - /* Devices */ -extern void __init at91_register_devices(void); - /* Timer */ -extern void __init at91_init_time(void); -extern void at91rm9200_ioremap_st(u32 addr); extern void at91rm9200_timer_init(void); -extern void at91sam926x_ioremap_pit(u32 addr); -extern void at91sam926x_pit_init(int irq); - - /* Power Management */ -extern void at91_irq_suspend(void); -extern void at91_irq_resume(void); /* idle */ extern void at91sam9_idle(void); /* Matrix */ extern void at91_ioremap_matrix(u32 base_addr); - -/* Ram Controler */ -extern void at91_ioremap_ramc(int id, u32 addr, u32 size); - - /* GPIO */ -#define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */ -#define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */ - -struct at91_gpio_bank { - unsigned short id; /* peripheral ID */ - unsigned long regbase; /* offset from system peripheral base */ -}; -extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks); -extern void __init at91_gpio_irq_setup(void); -extern int __init at91_gpio_of_irq_setup(struct device_node *node, - struct device_node *parent); - -extern u32 at91_get_extern_irq(void); - #endif /* _AT91_GENERIC_H */ diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c deleted file mode 100644 index d3f05aaad8ba..000000000000 --- a/arch/arm/mach-at91/gpio.c +++ /dev/null @@ -1,982 +0,0 @@ -/* - * linux/arch/arm/mach-at91/gpio.c - * - * Copyright (C) 2005 HP Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include <linux/clk.h> -#include <linux/errno.h> -#include <linux/device.h> -#include <linux/gpio.h> -#include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/debugfs.h> -#include <linux/seq_file.h> -#include <linux/kernel.h> -#include <linux/list.h> -#include <linux/module.h> -#include <linux/io.h> -#include <linux/irqdomain.h> -#include <linux/irqchip/chained_irq.h> -#include <linux/of_address.h> - -#include <mach/hardware.h> -#include <mach/at91_pio.h> - -#include "generic.h" -#include "gpio.h" - -#define MAX_NB_GPIO_PER_BANK 32 - -struct at91_gpio_chip { - struct gpio_chip chip; - struct at91_gpio_chip *next; /* Bank sharing same clock */ - int pioc_hwirq; /* PIO bank interrupt identifier on AIC */ - int pioc_virq; /* PIO bank Linux virtual interrupt */ - int pioc_idx; /* PIO bank index */ - void __iomem *regbase; /* PIO bank virtual address */ - struct clk *clock; /* associated clock */ - struct irq_domain *domain; /* associated irq domain */ -}; - -#define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip) - -static int at91_gpiolib_request(struct gpio_chip *chip, unsigned offset); -static void at91_gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip); -static void at91_gpiolib_set(struct gpio_chip *chip, unsigned offset, int val); -static int at91_gpiolib_get(struct gpio_chip *chip, unsigned offset); -static int at91_gpiolib_get_direction(struct gpio_chip *chip, unsigned offset); -static int at91_gpiolib_direction_output(struct gpio_chip *chip, - unsigned offset, int val); -static int at91_gpiolib_direction_input(struct gpio_chip *chip, - unsigned offset); -static int at91_gpiolib_to_irq(struct gpio_chip *chip, unsigned offset); - -#define AT91_GPIO_CHIP(name) \ - { \ - .chip = { \ - .label = name, \ - .request = at91_gpiolib_request, \ - .get_direction = at91_gpiolib_get_direction, \ - .direction_input = at91_gpiolib_direction_input, \ - .direction_output = at91_gpiolib_direction_output, \ - .get = at91_gpiolib_get, \ - .set = at91_gpiolib_set, \ - .dbg_show = at91_gpiolib_dbg_show, \ - .to_irq = at91_gpiolib_to_irq, \ - .ngpio = MAX_NB_GPIO_PER_BANK, \ - }, \ - } - -static struct at91_gpio_chip gpio_chip[] = { - AT91_GPIO_CHIP("pioA"), - AT91_GPIO_CHIP("pioB"), - AT91_GPIO_CHIP("pioC"), - AT91_GPIO_CHIP("pioD"), - AT91_GPIO_CHIP("pioE"), -}; - -static int gpio_banks; -static unsigned long at91_gpio_caps; - -/* All PIO controllers support PIO3 features */ -#define AT91_GPIO_CAP_PIO3 (1 << 0) - -#define has_pio3() (at91_gpio_caps & AT91_GPIO_CAP_PIO3) - -/*--------------------------------------------------------------------------*/ - -static inline void __iomem *pin_to_controller(unsigned pin) -{ - pin /= MAX_NB_GPIO_PER_BANK; - if (likely(pin < gpio_banks)) - return gpio_chip[pin].regbase; - - return NULL; -} - -static inline unsigned pin_to_mask(unsigned pin) -{ - return 1 << (pin % MAX_NB_GPIO_PER_BANK); -} - - -static char peripheral_function(void __iomem *pio, unsigned mask) -{ - char ret = 'X'; - u8 select; - - if (pio) { - if (has_pio3()) { - select = !!(__raw_readl(pio + PIO_ABCDSR1) & mask); - select |= (!!(__raw_readl(pio + PIO_ABCDSR2) & mask) << 1); - ret = 'A' + select; - } else { - ret = __raw_readl(pio + PIO_ABSR) & mask ? - 'B' : 'A'; - } - } - - return ret; -} - -/*--------------------------------------------------------------------------*/ - -/* Not all hardware capabilities are exposed through these calls; they - * only encapsulate the most common features and modes. (So if you - * want to change signals in groups, do it directly.) - * - * Bootloaders will usually handle some of the pin multiplexing setup. - * The intent is certainly that by the time Linux is fully booted, all - * pins should have been fully initialized. These setup calls should - * only be used by board setup routines, or possibly in driver probe(). - * - * For bootloaders doing all that setup, these calls could be inlined - * as NOPs so Linux won't duplicate any setup code - */ - - -/* - * mux the pin to the "GPIO" peripheral role. - */ -int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_PER); - return 0; -} -EXPORT_SYMBOL(at91_set_GPIO_periph); - - -/* - * mux the pin to the "A" internal peripheral role. - */ -int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - if (has_pio3()) { - __raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask, - pio + PIO_ABCDSR1); - __raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask, - pio + PIO_ABCDSR2); - } else { - __raw_writel(mask, pio + PIO_ASR); - } - __raw_writel(mask, pio + PIO_PDR); - return 0; -} -EXPORT_SYMBOL(at91_set_A_periph); - - -/* - * mux the pin to the "B" internal peripheral role. - */ -int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - if (has_pio3()) { - __raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask, - pio + PIO_ABCDSR1); - __raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask, - pio + PIO_ABCDSR2); - } else { - __raw_writel(mask, pio + PIO_BSR); - } - __raw_writel(mask, pio + PIO_PDR); - return 0; -} -EXPORT_SYMBOL(at91_set_B_periph); - - -/* - * mux the pin to the "C" internal peripheral role. - */ -int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio || !has_pio3()) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask, pio + PIO_ABCDSR1); - __raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2); - __raw_writel(mask, pio + PIO_PDR); - return 0; -} -EXPORT_SYMBOL(at91_set_C_periph); - - -/* - * mux the pin to the "D" internal peripheral role. - */ -int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio || !has_pio3()) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask, pio + PIO_ABCDSR1); - __raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2); - __raw_writel(mask, pio + PIO_PDR); - return 0; -} -EXPORT_SYMBOL(at91_set_D_periph); - - -/* - * mux the pin to the gpio controller (instead of "A", "B", "C" - * or "D" peripheral), and configure it for an input. - */ -int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_ODR); - __raw_writel(mask, pio + PIO_PER); - return 0; -} -EXPORT_SYMBOL(at91_set_gpio_input); - - -/* - * mux the pin to the gpio controller (instead of "A", "B", "C" - * or "D" peripheral), and configure it for an output. - */ -int __init_or_module at91_set_gpio_output(unsigned pin, int value) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + PIO_PUDR); - __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); - __raw_writel(mask, pio + PIO_OER); - __raw_writel(mask, pio + PIO_PER); - return 0; -} -EXPORT_SYMBOL(at91_set_gpio_output); - - -/* - * enable/disable the glitch filter; mostly used with IRQ handling. - */ -int __init_or_module at91_set_deglitch(unsigned pin, int is_on) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - if (has_pio3() && is_on) - __raw_writel(mask, pio + PIO_IFSCDR); - __raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR)); - return 0; -} -EXPORT_SYMBOL(at91_set_deglitch); - -/* - * enable/disable the debounce filter; - */ -int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio || !has_pio3()) - return -EINVAL; - - if (is_on) { - __raw_writel(mask, pio + PIO_IFSCER); - __raw_writel(div & PIO_SCDR_DIV, pio + PIO_SCDR); - __raw_writel(mask, pio + PIO_IFER); - } else { - __raw_writel(mask, pio + PIO_IFDR); - } - return 0; -} -EXPORT_SYMBOL(at91_set_debounce); - -/* - * enable/disable the multi-driver; This is only valid for output and - * allows the output pin to run as an open collector output. - */ -int __init_or_module at91_set_multi_drive(unsigned pin, int is_on) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + (is_on ? PIO_MDER : PIO_MDDR)); - return 0; -} -EXPORT_SYMBOL(at91_set_multi_drive); - -/* - * enable/disable the pull-down. - * If pull-up already enabled while calling the function, we disable it. - */ -int __init_or_module at91_set_pulldown(unsigned pin, int is_on) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio || !has_pio3()) - return -EINVAL; - - /* Disable pull-up anyway */ - __raw_writel(mask, pio + PIO_PUDR); - __raw_writel(mask, pio + (is_on ? PIO_PPDER : PIO_PPDDR)); - return 0; -} -EXPORT_SYMBOL(at91_set_pulldown); - -/* - * disable Schmitt trigger - */ -int __init_or_module at91_disable_schmitt_trig(unsigned pin) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio || !has_pio3()) - return -EINVAL; - - __raw_writel(__raw_readl(pio + PIO_SCHMITT) | mask, pio + PIO_SCHMITT); - return 0; -} -EXPORT_SYMBOL(at91_disable_schmitt_trig); - -/* - * assuming the pin is muxed as a gpio output, set its value. - */ -int at91_set_gpio_value(unsigned pin, int value) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); - return 0; -} -EXPORT_SYMBOL(at91_set_gpio_value); - - -/* - * read the pin's value (works even if it's not muxed as a gpio). - */ -int at91_get_gpio_value(unsigned pin) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - u32 pdsr; - - if (!pio) - return -EINVAL; - pdsr = __raw_readl(pio + PIO_PDSR); - return (pdsr & mask) != 0; -} -EXPORT_SYMBOL(at91_get_gpio_value); - -/*--------------------------------------------------------------------------*/ - -#ifdef CONFIG_PM - -static u32 wakeups[MAX_GPIO_BANKS]; -static u32 backups[MAX_GPIO_BANKS]; - -static int gpio_irq_set_wake(struct irq_data *d, unsigned state) -{ - struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d); - unsigned mask = 1 << d->hwirq; - unsigned bank = at91_gpio->pioc_idx; - - if (unlikely(bank >= MAX_GPIO_BANKS)) - return -EINVAL; - - if (state) - wakeups[bank] |= mask; - else - wakeups[bank] &= ~mask; - - irq_set_irq_wake(at91_gpio->pioc_virq, state); - - return 0; -} - -void at91_gpio_suspend(void) -{ - int i; - - for (i = 0; i < gpio_banks; i++) { - void __iomem *pio = gpio_chip[i].regbase; - - backups[i] = __raw_readl(pio + PIO_IMR); - __raw_writel(backups[i], pio + PIO_IDR); - __raw_writel(wakeups[i], pio + PIO_IER); - - if (!wakeups[i]) { - clk_unprepare(gpio_chip[i].clock); - clk_disable(gpio_chip[i].clock); - } else { -#ifdef CONFIG_PM_DEBUG - printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]); -#endif - } - } -} - -void at91_gpio_resume(void) -{ - int i; - - for (i = 0; i < gpio_banks; i++) { - void __iomem *pio = gpio_chip[i].regbase; - - if (!wakeups[i]) { - if (clk_prepare(gpio_chip[i].clock) == 0) - clk_enable(gpio_chip[i].clock); - } - - __raw_writel(wakeups[i], pio + PIO_IDR); - __raw_writel(backups[i], pio + PIO_IER); - } -} - -#else -#define gpio_irq_set_wake NULL -#endif - - -/* Several AIC controller irqs are dispatched through this GPIO handler. - * To use any AT91_PIN_* as an externally triggered IRQ, first call - * at91_set_gpio_input() then maybe enable its glitch filter. - * Then just request_irq() with the pin ID; it works like any ARM IRQ - * handler. - * First implementation always triggers on rising and falling edges - * whereas the newer PIO3 can be additionally configured to trigger on - * level, edge with any polarity. - * - * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after - * configuring them with at91_set_a_periph() or at91_set_b_periph(). - * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering. - */ - -static void gpio_irq_mask(struct irq_data *d) -{ - struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << d->hwirq; - - if (pio) - __raw_writel(mask, pio + PIO_IDR); -} - -static void gpio_irq_unmask(struct irq_data *d) -{ - struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << d->hwirq; - - if (pio) - __raw_writel(mask, pio + PIO_IER); -} - -static int gpio_irq_type(struct irq_data *d, unsigned type) -{ - switch (type) { - case IRQ_TYPE_NONE: - case IRQ_TYPE_EDGE_BOTH: - return 0; - default: - return -EINVAL; - } -} - -/* Alternate irq type for PIO3 support */ -static int alt_gpio_irq_type(struct irq_data *d, unsigned type) -{ - struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << d->hwirq; - - switch (type) { - case IRQ_TYPE_EDGE_RISING: - __raw_writel(mask, pio + PIO_ESR); - __raw_writel(mask, pio + PIO_REHLSR); - break; - case IRQ_TYPE_EDGE_FALLING: - __raw_writel(mask, pio + PIO_ESR); - __raw_writel(mask, pio + PIO_FELLSR); - break; - case IRQ_TYPE_LEVEL_LOW: - __raw_writel(mask, pio + PIO_LSR); - __raw_writel(mask, pio + PIO_FELLSR); - break; - case IRQ_TYPE_LEVEL_HIGH: - __raw_writel(mask, pio + PIO_LSR); - __raw_writel(mask, pio + PIO_REHLSR); - break; - case IRQ_TYPE_EDGE_BOTH: - /* - * disable additional interrupt modes: - * fall back to default behavior - */ - __raw_writel(mask, pio + PIO_AIMDR); - return 0; - case IRQ_TYPE_NONE: - default: - pr_warn("AT91: No type for irq %d\n", gpio_to_irq(d->irq)); - return -EINVAL; - } - - /* enable additional interrupt modes */ - __raw_writel(mask, pio + PIO_AIMER); - - return 0; -} - -static struct irq_chip gpio_irqchip = { - .name = "GPIO", - .irq_disable = gpio_irq_mask, - .irq_mask = gpio_irq_mask, - .irq_unmask = gpio_irq_unmask, - /* .irq_set_type is set dynamically */ - .irq_set_wake = gpio_irq_set_wake, -}; - -static void gpio_irq_handler(unsigned irq, struct irq_desc *desc) -{ - struct irq_chip *chip = irq_desc_get_chip(desc); - struct irq_data *idata = irq_desc_get_irq_data(desc); - struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata); - void __iomem *pio = at91_gpio->regbase; - unsigned long isr; - int n; - - chained_irq_enter(chip, desc); - for (;;) { - /* Reading ISR acks pending (edge triggered) GPIO interrupts. - * When there none are pending, we're finished unless we need - * to process multiple banks (like ID_PIOCDE on sam9263). - */ - isr = __raw_readl(pio + PIO_ISR) & __raw_readl(pio + PIO_IMR); - if (!isr) { - if (!at91_gpio->next) - break; - at91_gpio = at91_gpio->next; - pio = at91_gpio->regbase; - continue; - } - - n = find_first_bit(&isr, BITS_PER_LONG); - while (n < BITS_PER_LONG) { - generic_handle_irq(irq_find_mapping(at91_gpio->domain, n)); - n = find_next_bit(&isr, BITS_PER_LONG, n + 1); - } - } - chained_irq_exit(chip, desc); - /* now it may re-trigger */ -} - -/*--------------------------------------------------------------------------*/ - -#ifdef CONFIG_DEBUG_FS - -static void gpio_printf(struct seq_file *s, void __iomem *pio, unsigned mask) -{ - char *trigger = NULL; - char *polarity = NULL; - - if (__raw_readl(pio + PIO_IMR) & mask) { - if (!has_pio3() || !(__raw_readl(pio + PIO_AIMMR) & mask )) { - trigger = "edge"; - polarity = "both"; - } else { - if (__raw_readl(pio + PIO_ELSR) & mask) { - trigger = "level"; - polarity = __raw_readl(pio + PIO_FRLHSR) & mask ? - "high" : "low"; - } else { - trigger = "edge"; - polarity = __raw_readl(pio + PIO_FRLHSR) & mask ? - "rising" : "falling"; - } - } - seq_printf(s, "IRQ:%s-%s\t", trigger, polarity); - } else { - seq_printf(s, "GPIO:%s\t\t", - __raw_readl(pio + PIO_PDSR) & mask ? "1" : "0"); - } -} - -static int at91_gpio_show(struct seq_file *s, void *unused) -{ - int bank, j; - - /* print heading */ - seq_printf(s, "Pin\t"); - for (bank = 0; bank < gpio_banks; bank++) { - seq_printf(s, "PIO%c\t\t", 'A' + bank); - }; - seq_printf(s, "\n\n"); - - /* print pin status */ - for (j = 0; j < 32; j++) { - seq_printf(s, "%i:\t", j); - - for (bank = 0; bank < gpio_banks; bank++) { - unsigned pin = (32 * bank) + j; - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (__raw_readl(pio + PIO_PSR) & mask) - gpio_printf(s, pio, mask); - else - seq_printf(s, "%c\t\t", - peripheral_function(pio, mask)); - } - - seq_printf(s, "\n"); - } - - return 0; -} - -static int at91_gpio_open(struct inode *inode, struct file *file) -{ - return single_open(file, at91_gpio_show, NULL); -} - -static const struct file_operations at91_gpio_operations = { - .open = at91_gpio_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; - -static int __init at91_gpio_debugfs_init(void) -{ - /* /sys/kernel/debug/at91_gpio */ - (void) debugfs_create_file("at91_gpio", S_IFREG | S_IRUGO, NULL, NULL, &at91_gpio_operations); - return 0; -} -postcore_initcall(at91_gpio_debugfs_init); - -#endif - -/*--------------------------------------------------------------------------*/ - -/* - * This lock class tells lockdep that GPIO irqs are in a different - * category than their parents, so it won't report false recursion. - */ -static struct lock_class_key gpio_lock_class; - -/* - * irqdomain initialization: pile up irqdomains on top of AIC range - */ -static void __init at91_gpio_irqdomain(struct at91_gpio_chip *at91_gpio) -{ - int irq_base; - - irq_base = irq_alloc_descs(-1, 0, at91_gpio->chip.ngpio, 0); - if (irq_base < 0) - panic("at91_gpio.%d: error %d: couldn't allocate IRQ numbers.\n", - at91_gpio->pioc_idx, irq_base); - at91_gpio->domain = irq_domain_add_legacy(NULL, at91_gpio->chip.ngpio, - irq_base, 0, - &irq_domain_simple_ops, NULL); - if (!at91_gpio->domain) - panic("at91_gpio.%d: couldn't allocate irq domain.\n", - at91_gpio->pioc_idx); -} - -/* - * Called from the processor-specific init to enable GPIO interrupt support. - */ -void __init at91_gpio_irq_setup(void) -{ - unsigned pioc; - int gpio_irqnbr = 0; - struct at91_gpio_chip *this, *prev; - - /* Setup proper .irq_set_type function */ - if (has_pio3()) - gpio_irqchip.irq_set_type = alt_gpio_irq_type; - else - gpio_irqchip.irq_set_type = gpio_irq_type; - - for (pioc = 0, this = gpio_chip, prev = NULL; - pioc++ < gpio_banks; - prev = this, this++) { - int offset; - - __raw_writel(~0, this->regbase + PIO_IDR); - - /* setup irq domain for this GPIO controller */ - at91_gpio_irqdomain(this); - - for (offset = 0; offset < this->chip.ngpio; offset++) { - unsigned int virq = irq_find_mapping(this->domain, offset); - irq_set_lockdep_class(virq, &gpio_lock_class); - - /* - * Can use the "simple" and not "edge" handler since it's - * shorter, and the AIC handles interrupts sanely. - */ - irq_set_chip_and_handler(virq, &gpio_irqchip, - handle_simple_irq); - set_irq_flags(virq, IRQF_VALID); - irq_set_chip_data(virq, this); - - gpio_irqnbr++; - } - - /* The toplevel handler handles one bank of GPIOs, except - * on some SoC it can handles up to three... - * We only set up the handler for the first of the list. - */ - if (prev && prev->next == this) - continue; - - this->pioc_virq = irq_create_mapping(NULL, this->pioc_hwirq); - irq_set_chip_data(this->pioc_virq, this); - irq_set_chained_handler(this->pioc_virq, gpio_irq_handler); - } - pr_info("AT91: %d gpio irqs in %d banks\n", gpio_irqnbr, gpio_banks); -} - -/* gpiolib support */ -static int at91_gpiolib_request(struct gpio_chip *chip, unsigned offset) -{ - struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << offset; - - __raw_writel(mask, pio + PIO_PER); - return 0; -} - -static int at91_gpiolib_get_direction(struct gpio_chip *chip, unsigned offset) -{ - struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << offset; - u32 osr; - - osr = __raw_readl(pio + PIO_OSR); - return !(osr & mask); -} - -static int at91_gpiolib_direction_input(struct gpio_chip *chip, - unsigned offset) -{ - struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << offset; - - __raw_writel(mask, pio + PIO_ODR); - return 0; -} - -static int at91_gpiolib_direction_output(struct gpio_chip *chip, - unsigned offset, int val) -{ - struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << offset; - - __raw_writel(mask, pio + (val ? PIO_SODR : PIO_CODR)); - __raw_writel(mask, pio + PIO_OER); - return 0; -} - -static int at91_gpiolib_get(struct gpio_chip *chip, unsigned offset) -{ - struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << offset; - u32 pdsr; - - pdsr = __raw_readl(pio + PIO_PDSR); - return (pdsr & mask) != 0; -} - -static void at91_gpiolib_set(struct gpio_chip *chip, unsigned offset, int val) -{ - struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip); - void __iomem *pio = at91_gpio->regbase; - unsigned mask = 1 << offset; - - __raw_writel(mask, pio + (val ? PIO_SODR : PIO_CODR)); -} - -static void at91_gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip) -{ - int i; - - for (i = 0; i < chip->ngpio; i++) { - unsigned pin = chip->base + i; - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - const char *gpio_label; - - gpio_label = gpiochip_is_requested(chip, i); - if (gpio_label) { - seq_printf(s, "[%s] GPIO%s%d: ", - gpio_label, chip->label, i); - if (__raw_readl(pio + PIO_PSR) & mask) - seq_printf(s, "[gpio] %s\n", - at91_get_gpio_value(pin) ? - "set" : "clear"); - else - seq_printf(s, "[periph %c]\n", - peripheral_function(pio, mask)); - } - } -} - -static int at91_gpiolib_to_irq(struct gpio_chip *chip, unsigned offset) -{ - struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip); - int virq; - - if (offset < chip->ngpio) - virq = irq_create_mapping(at91_gpio->domain, offset); - else - virq = -ENXIO; - - dev_dbg(chip->dev, "%s: request IRQ for GPIO %d, return %d\n", - chip->label, offset + chip->base, virq); - return virq; -} - -static int __init at91_gpio_setup_clk(int idx) -{ - struct at91_gpio_chip *at91_gpio = &gpio_chip[idx]; - - /* retreive PIO controller's clock */ - at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label); - if (IS_ERR(at91_gpio->clock)) { - pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", idx); - goto err; - } - - if (clk_prepare(at91_gpio->clock)) - goto clk_prep_err; - - /* enable PIO controller's clock */ - if (clk_enable(at91_gpio->clock)) { - pr_err("at91_gpio.%d, failed to enable clock, ignoring.\n", idx); - goto clk_err; - } - - return 0; - -clk_err: - clk_unprepare(at91_gpio->clock); -clk_prep_err: - clk_put(at91_gpio->clock); -err: - return -EINVAL; -} - -static void __init at91_gpio_init_one(int idx, u32 regbase, int pioc_hwirq) -{ - struct at91_gpio_chip *at91_gpio = &gpio_chip[idx]; - - at91_gpio->chip.base = idx * MAX_NB_GPIO_PER_BANK; - at91_gpio->pioc_hwirq = pioc_hwirq; - at91_gpio->pioc_idx = idx; - - at91_gpio->regbase = ioremap(regbase, 512); - if (!at91_gpio->regbase) { - pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", idx); - return; - } - - if (at91_gpio_setup_clk(idx)) - goto ioremap_err; - - gpio_banks = max(gpio_banks, idx + 1); - return; - -ioremap_err: - iounmap(at91_gpio->regbase); -} - -/* - * Called from the processor-specific init to enable GPIO pin support. - */ -void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks) -{ - unsigned i; - struct at91_gpio_chip *at91_gpio, *last = NULL; - - BUG_ON(nr_banks > MAX_GPIO_BANKS); - - if (of_have_populated_dt()) - return; - - for (i = 0; i < nr_banks; i++) - at91_gpio_init_one(i, data[i].regbase, data[i].id); - - for (i = 0; i < gpio_banks; i++) { - at91_gpio = &gpio_chip[i]; - - /* - * GPIO controller are grouped on some SoC: - * PIOC, PIOD and PIOE can share the same IRQ line - */ - if (last && last->pioc_hwirq == at91_gpio->pioc_hwirq) - last->next = at91_gpio; - last = at91_gpio; - - gpiochip_add(&at91_gpio->chip); - } -} diff --git a/arch/arm/mach-at91/gpio.h b/arch/arm/mach-at91/gpio.h deleted file mode 100644 index eed465ab0dd7..000000000000 --- a/arch/arm/mach-at91/gpio.h +++ /dev/null @@ -1,214 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/gpio.h - * - * Copyright (C) 2005 HP Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#ifndef __ASM_ARCH_AT91RM9200_GPIO_H -#define __ASM_ARCH_AT91RM9200_GPIO_H - -#include <linux/kernel.h> -#include <asm/irq.h> - -#define MAX_GPIO_BANKS 5 -#define NR_BUILTIN_GPIO (MAX_GPIO_BANKS * 32) - -/* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */ - -#define AT91_PIN_PA0 (0x00 + 0) -#define AT91_PIN_PA1 (0x00 + 1) -#define AT91_PIN_PA2 (0x00 + 2) -#define AT91_PIN_PA3 (0x00 + 3) -#define AT91_PIN_PA4 (0x00 + 4) -#define AT91_PIN_PA5 (0x00 + 5) -#define AT91_PIN_PA6 (0x00 + 6) -#define AT91_PIN_PA7 (0x00 + 7) -#define AT91_PIN_PA8 (0x00 + 8) -#define AT91_PIN_PA9 (0x00 + 9) -#define AT91_PIN_PA10 (0x00 + 10) -#define AT91_PIN_PA11 (0x00 + 11) -#define AT91_PIN_PA12 (0x00 + 12) -#define AT91_PIN_PA13 (0x00 + 13) -#define AT91_PIN_PA14 (0x00 + 14) -#define AT91_PIN_PA15 (0x00 + 15) -#define AT91_PIN_PA16 (0x00 + 16) -#define AT91_PIN_PA17 (0x00 + 17) -#define AT91_PIN_PA18 (0x00 + 18) -#define AT91_PIN_PA19 (0x00 + 19) -#define AT91_PIN_PA20 (0x00 + 20) -#define AT91_PIN_PA21 (0x00 + 21) -#define AT91_PIN_PA22 (0x00 + 22) -#define AT91_PIN_PA23 (0x00 + 23) -#define AT91_PIN_PA24 (0x00 + 24) -#define AT91_PIN_PA25 (0x00 + 25) -#define AT91_PIN_PA26 (0x00 + 26) -#define AT91_PIN_PA27 (0x00 + 27) -#define AT91_PIN_PA28 (0x00 + 28) -#define AT91_PIN_PA29 (0x00 + 29) -#define AT91_PIN_PA30 (0x00 + 30) -#define AT91_PIN_PA31 (0x00 + 31) - -#define AT91_PIN_PB0 (0x20 + 0) -#define AT91_PIN_PB1 (0x20 + 1) -#define AT91_PIN_PB2 (0x20 + 2) -#define AT91_PIN_PB3 (0x20 + 3) -#define AT91_PIN_PB4 (0x20 + 4) -#define AT91_PIN_PB5 (0x20 + 5) -#define AT91_PIN_PB6 (0x20 + 6) -#define AT91_PIN_PB7 (0x20 + 7) -#define AT91_PIN_PB8 (0x20 + 8) -#define AT91_PIN_PB9 (0x20 + 9) -#define AT91_PIN_PB10 (0x20 + 10) -#define AT91_PIN_PB11 (0x20 + 11) -#define AT91_PIN_PB12 (0x20 + 12) -#define AT91_PIN_PB13 (0x20 + 13) -#define AT91_PIN_PB14 (0x20 + 14) -#define AT91_PIN_PB15 (0x20 + 15) -#define AT91_PIN_PB16 (0x20 + 16) -#define AT91_PIN_PB17 (0x20 + 17) -#define AT91_PIN_PB18 (0x20 + 18) -#define AT91_PIN_PB19 (0x20 + 19) -#define AT91_PIN_PB20 (0x20 + 20) -#define AT91_PIN_PB21 (0x20 + 21) -#define AT91_PIN_PB22 (0x20 + 22) -#define AT91_PIN_PB23 (0x20 + 23) -#define AT91_PIN_PB24 (0x20 + 24) -#define AT91_PIN_PB25 (0x20 + 25) -#define AT91_PIN_PB26 (0x20 + 26) -#define AT91_PIN_PB27 (0x20 + 27) -#define AT91_PIN_PB28 (0x20 + 28) -#define AT91_PIN_PB29 (0x20 + 29) -#define AT91_PIN_PB30 (0x20 + 30) -#define AT91_PIN_PB31 (0x20 + 31) - -#define AT91_PIN_PC0 (0x40 + 0) -#define AT91_PIN_PC1 (0x40 + 1) -#define AT91_PIN_PC2 (0x40 + 2) -#define AT91_PIN_PC3 (0x40 + 3) -#define AT91_PIN_PC4 (0x40 + 4) -#define AT91_PIN_PC5 (0x40 + 5) -#define AT91_PIN_PC6 (0x40 + 6) -#define AT91_PIN_PC7 (0x40 + 7) -#define AT91_PIN_PC8 (0x40 + 8) -#define AT91_PIN_PC9 (0x40 + 9) -#define AT91_PIN_PC10 (0x40 + 10) -#define AT91_PIN_PC11 (0x40 + 11) -#define AT91_PIN_PC12 (0x40 + 12) -#define AT91_PIN_PC13 (0x40 + 13) -#define AT91_PIN_PC14 (0x40 + 14) -#define AT91_PIN_PC15 (0x40 + 15) -#define AT91_PIN_PC16 (0x40 + 16) -#define AT91_PIN_PC17 (0x40 + 17) -#define AT91_PIN_PC18 (0x40 + 18) -#define AT91_PIN_PC19 (0x40 + 19) -#define AT91_PIN_PC20 (0x40 + 20) -#define AT91_PIN_PC21 (0x40 + 21) -#define AT91_PIN_PC22 (0x40 + 22) -#define AT91_PIN_PC23 (0x40 + 23) -#define AT91_PIN_PC24 (0x40 + 24) -#define AT91_PIN_PC25 (0x40 + 25) -#define AT91_PIN_PC26 (0x40 + 26) -#define AT91_PIN_PC27 (0x40 + 27) -#define AT91_PIN_PC28 (0x40 + 28) -#define AT91_PIN_PC29 (0x40 + 29) -#define AT91_PIN_PC30 (0x40 + 30) -#define AT91_PIN_PC31 (0x40 + 31) - -#define AT91_PIN_PD0 (0x60 + 0) -#define AT91_PIN_PD1 (0x60 + 1) -#define AT91_PIN_PD2 (0x60 + 2) -#define AT91_PIN_PD3 (0x60 + 3) -#define AT91_PIN_PD4 (0x60 + 4) -#define AT91_PIN_PD5 (0x60 + 5) -#define AT91_PIN_PD6 (0x60 + 6) -#define AT91_PIN_PD7 (0x60 + 7) -#define AT91_PIN_PD8 (0x60 + 8) -#define AT91_PIN_PD9 (0x60 + 9) -#define AT91_PIN_PD10 (0x60 + 10) -#define AT91_PIN_PD11 (0x60 + 11) -#define AT91_PIN_PD12 (0x60 + 12) -#define AT91_PIN_PD13 (0x60 + 13) -#define AT91_PIN_PD14 (0x60 + 14) -#define AT91_PIN_PD15 (0x60 + 15) -#define AT91_PIN_PD16 (0x60 + 16) -#define AT91_PIN_PD17 (0x60 + 17) -#define AT91_PIN_PD18 (0x60 + 18) -#define AT91_PIN_PD19 (0x60 + 19) -#define AT91_PIN_PD20 (0x60 + 20) -#define AT91_PIN_PD21 (0x60 + 21) -#define AT91_PIN_PD22 (0x60 + 22) -#define AT91_PIN_PD23 (0x60 + 23) -#define AT91_PIN_PD24 (0x60 + 24) -#define AT91_PIN_PD25 (0x60 + 25) -#define AT91_PIN_PD26 (0x60 + 26) -#define AT91_PIN_PD27 (0x60 + 27) -#define AT91_PIN_PD28 (0x60 + 28) -#define AT91_PIN_PD29 (0x60 + 29) -#define AT91_PIN_PD30 (0x60 + 30) -#define AT91_PIN_PD31 (0x60 + 31) - -#define AT91_PIN_PE0 (0x80 + 0) -#define AT91_PIN_PE1 (0x80 + 1) -#define AT91_PIN_PE2 (0x80 + 2) -#define AT91_PIN_PE3 (0x80 + 3) -#define AT91_PIN_PE4 (0x80 + 4) -#define AT91_PIN_PE5 (0x80 + 5) -#define AT91_PIN_PE6 (0x80 + 6) -#define AT91_PIN_PE7 (0x80 + 7) -#define AT91_PIN_PE8 (0x80 + 8) -#define AT91_PIN_PE9 (0x80 + 9) -#define AT91_PIN_PE10 (0x80 + 10) -#define AT91_PIN_PE11 (0x80 + 11) -#define AT91_PIN_PE12 (0x80 + 12) -#define AT91_PIN_PE13 (0x80 + 13) -#define AT91_PIN_PE14 (0x80 + 14) -#define AT91_PIN_PE15 (0x80 + 15) -#define AT91_PIN_PE16 (0x80 + 16) -#define AT91_PIN_PE17 (0x80 + 17) -#define AT91_PIN_PE18 (0x80 + 18) -#define AT91_PIN_PE19 (0x80 + 19) -#define AT91_PIN_PE20 (0x80 + 20) -#define AT91_PIN_PE21 (0x80 + 21) -#define AT91_PIN_PE22 (0x80 + 22) -#define AT91_PIN_PE23 (0x80 + 23) -#define AT91_PIN_PE24 (0x80 + 24) -#define AT91_PIN_PE25 (0x80 + 25) -#define AT91_PIN_PE26 (0x80 + 26) -#define AT91_PIN_PE27 (0x80 + 27) -#define AT91_PIN_PE28 (0x80 + 28) -#define AT91_PIN_PE29 (0x80 + 29) -#define AT91_PIN_PE30 (0x80 + 30) -#define AT91_PIN_PE31 (0x80 + 31) - -#ifndef __ASSEMBLY__ -/* setup setup routines, called from board init or driver probe() */ -extern int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_gpio_output(unsigned pin, int value); -extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on); -extern int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div); -extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on); -extern int __init_or_module at91_set_pulldown(unsigned pin, int is_on); -extern int __init_or_module at91_disable_schmitt_trig(unsigned pin); - -/* callable at any time */ -extern int at91_set_gpio_value(unsigned pin, int value); -extern int at91_get_gpio_value(unsigned pin); - -/* callable only from core power-management code */ -extern void at91_gpio_suspend(void); -extern void at91_gpio_resume(void); - -#endif /* __ASSEMBLY__ */ - -#endif diff --git a/arch/arm/mach-at91/gsia18s.h b/arch/arm/mach-at91/gsia18s.h deleted file mode 100644 index 307c194926f9..000000000000 --- a/arch/arm/mach-at91/gsia18s.h +++ /dev/null @@ -1,33 +0,0 @@ -/* Buttons */ -#define GPIO_TRIG_NET_IN AT91_PIN_PB21 -#define GPIO_CARD_UNMOUNT_0 AT91_PIN_PB13 -#define GPIO_CARD_UNMOUNT_1 AT91_PIN_PB12 -#define GPIO_KEY_POWER AT91_PIN_PA25 - -/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */ -#define GS_IA18_S_PCF_GPIO_BASE0 NR_BUILTIN_GPIO -#define PCF_GPIO_HDC_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 0) -#define PCF_GPIO_WIFI_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 1) -#define PCF_GPIO_WIFI_ENABLE (GS_IA18_S_PCF_GPIO_BASE0 + 2) -#define PCF_GPIO_WIFI_RESET (GS_IA18_S_PCF_GPIO_BASE0 + 3) -#define PCF_GPIO_ETH_DETECT 4 /* this is a GPI */ -#define PCF_GPIO_GPS_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 5) -#define PCF_GPIO_GPS_STANDBY (GS_IA18_S_PCF_GPIO_BASE0 + 6) -#define PCF_GPIO_GPS_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 7) - -/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */ -#define GS_IA18_S_PCF_GPIO_BASE1 (GS_IA18_S_PCF_GPIO_BASE0 + 8) -#define PCF_GPIO_ALARM1 (GS_IA18_S_PCF_GPIO_BASE1 + 0) -#define PCF_GPIO_ALARM2 (GS_IA18_S_PCF_GPIO_BASE1 + 1) -#define PCF_GPIO_ALARM3 (GS_IA18_S_PCF_GPIO_BASE1 + 2) -#define PCF_GPIO_ALARM4 (GS_IA18_S_PCF_GPIO_BASE1 + 3) -/* bits 4, 5, 6 not used */ -#define PCF_GPIO_ALARM_V_RELAY_ON (GS_IA18_S_PCF_GPIO_BASE1 + 7) - -/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */ -#define GS_IA18_S_PCF_GPIO_BASE2 (GS_IA18_S_PCF_GPIO_BASE1 + 8) -#define PCF_GPIO_MODEM_POWER (GS_IA18_S_PCF_GPIO_BASE2 + 0) -#define PCF_GPIO_MODEM_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 3) -/* bits 1, 2, 4, 5 not used */ -#define PCF_GPIO_TRX_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 6) -/* bit 7 not used */ diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h index a57c1c52a574..cacbaa52418f 100644 --- a/arch/arm/mach-at91/include/mach/hardware.h +++ b/arch/arm/mach-at91/include/mach/hardware.h @@ -127,13 +127,8 @@ * called as part of the generic suspend/resume path. */ #ifndef __ASSEMBLY__ -#ifdef CONFIG_PINCTRL_AT91 extern void at91_pinctrl_gpio_suspend(void); extern void at91_pinctrl_gpio_resume(void); -#else -static inline void at91_pinctrl_gpio_suspend(void) {} -static inline void at91_pinctrl_gpio_resume(void) {} -#endif #endif #endif diff --git a/arch/arm/mach-at91/leds.c b/arch/arm/mach-at91/leds.c deleted file mode 100644 index eb22e3357e87..000000000000 --- a/arch/arm/mach-at91/leds.c +++ /dev/null @@ -1,56 +0,0 @@ -/* - * LED driver for Atmel AT91-based boards. - * - * Copyright (C) SAN People (Pty) Ltd - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. -*/ - -#include <linux/gpio.h> -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/platform_device.h> - -#include "board.h" -#include "gpio.h" - - -/* ------------------------------------------------------------------------- */ - -#if defined(CONFIG_NEW_LEDS) - -/* - * New cross-platform LED support. - */ - -static struct gpio_led_platform_data led_data; - -static struct platform_device at91_gpio_leds_device = { - .name = "leds-gpio", - .id = -1, - .dev.platform_data = &led_data, -}; - -void __init at91_gpio_leds(struct gpio_led *leds, int nr) -{ - int i; - - if (!nr) - return; - - for (i = 0; i < nr; i++) - at91_set_gpio_output(leds[i].gpio, leds[i].active_low); - - led_data.leds = leds; - led_data.num_leds = nr; - platform_device_register(&at91_gpio_leds_device); -} - -#else -void __init at91_gpio_leds(struct gpio_led *leds, int nr) {} -#endif - diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index a42360f69127..9b15169a1c62 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -31,7 +31,6 @@ #include "generic.h" #include "pm.h" -#include "gpio.h" static void (*at91_pm_standby)(void); @@ -130,10 +129,7 @@ extern u32 at91_slow_clock_sz; static int at91_pm_enter(suspend_state_t state) { - if (of_have_populated_dt()) - at91_pinctrl_gpio_suspend(); - else - at91_gpio_suspend(); + at91_pinctrl_gpio_suspend(); switch (state) { /* @@ -201,10 +197,7 @@ static int at91_pm_enter(suspend_state_t state) error: target_state = PM_SUSPEND_ON; - if (of_have_populated_dt()) - at91_pinctrl_gpio_resume(); - else - at91_gpio_resume(); + at91_pinctrl_gpio_resume(); return 0; } diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c index 6c3013e3309b..ce25e85720fb 100644 --- a/arch/arm/mach-at91/setup.c +++ b/arch/arm/mach-at91/setup.c @@ -42,31 +42,9 @@ void __init at91rm9200_set_type(int type) at91_get_soc_subtype(&at91_soc_initdata)); } -void __init at91_init_irq_default(void) -{ - at91_init_interrupts(at91_boot_soc.default_irq_priority); -} - -void __init at91_init_interrupts(unsigned int *priority) -{ - /* Enable GPIO interrupts */ - at91_gpio_irq_setup(); -} - void __iomem *at91_ramc_base[2]; EXPORT_SYMBOL_GPL(at91_ramc_base); -void __init at91_ioremap_ramc(int id, u32 addr, u32 size) -{ - if (id < 0 || id > 1) { - pr_emerg("Wrong RAM controller id (%d), cannot continue\n", id); - BUG(); - } - at91_ramc_base[id] = ioremap(addr, size); - if (!at91_ramc_base[id]) - panic(pr_fmt("Impossible to ioremap ramc.%d 0x%x\n"), id, addr); -} - static struct map_desc sram_desc[2] __initdata; void __init at91_init_sram(int bank, unsigned long base, unsigned int length) @@ -414,7 +392,6 @@ void __init at91_ioremap_matrix(u32 base_addr) panic(pr_fmt("Impossible to ioremap at91_matrix_base\n")); } -#if defined(CONFIG_OF) static struct of_device_id ramc_ids[] = { { .compatible = "atmel,at91rm9200-sdramc", .data = at91rm9200_standby }, { .compatible = "atmel,at91sam9260-sdramc", .data = at91sam9_sdram_standby }, @@ -456,10 +433,6 @@ void __init at91rm9200_dt_initialize(void) { at91_dt_ramc(); - /* Register the processor-specific clocks */ - if (at91_boot_soc.register_clocks) - at91_boot_soc.register_clocks(); - at91_boot_soc.init(); } @@ -467,33 +440,6 @@ void __init at91_dt_initialize(void) { at91_dt_ramc(); - /* Register the processor-specific clocks */ - if (at91_boot_soc.register_clocks) - at91_boot_soc.register_clocks(); - if (at91_boot_soc.init) at91_boot_soc.init(); } -#endif - -void __init at91_initialize(unsigned long main_clock) -{ - at91_boot_soc.ioremap_registers(); - - /* Register the processor-specific clocks */ - at91_boot_soc.register_clocks(); - - at91_boot_soc.init(); - - pinctrl_provide_dummies(); -} - -void __init at91_register_devices(void) -{ - at91_boot_soc.register_devices(); -} - -void __init at91_init_time(void) -{ - at91_boot_soc.init_time(); -} diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h index 9a8fd97a8bef..ae6c0b2f1146 100644 --- a/arch/arm/mach-at91/soc.h +++ b/arch/arm/mach-at91/soc.h @@ -6,14 +6,8 @@ struct at91_init_soc { int builtin; - u32 extern_irq; - unsigned int *default_irq_priority; void (*map_io)(void); - void (*ioremap_registers)(void); - void (*register_clocks)(void); - void (*register_devices)(void); void (*init)(void); - void (*init_time)(void); }; extern struct at91_init_soc at91_boot_soc; diff --git a/drivers/clocksource/timer-atmel-pit.c b/drivers/clocksource/timer-atmel-pit.c index d5289098b3df..b5b4d4585c9a 100644 --- a/drivers/clocksource/timer-atmel-pit.c +++ b/drivers/clocksource/timer-atmel-pit.c @@ -262,35 +262,3 @@ static void __init at91sam926x_pit_dt_init(struct device_node *node) } CLOCKSOURCE_OF_DECLARE(at91sam926x_pit, "atmel,at91sam9260-pit", at91sam926x_pit_dt_init); - -static void __iomem *pit_base_addr; - -void __init at91sam926x_pit_init(int irq) -{ - struct pit_data *data; - - data = kzalloc(sizeof(*data), GFP_KERNEL); - if (!data) - panic(pr_fmt("Unable to allocate memory\n")); - - data->base = pit_base_addr; - - data->mck = clk_get(NULL, "mck"); - if (IS_ERR(data->mck)) - panic(pr_fmt("Unable to get mck clk\n")); - - data->irq = irq; - - at91sam926x_pit_common_init(data); -} - -void __init at91sam926x_ioremap_pit(u32 addr) -{ - if (of_have_populated_dt()) - return; - - pit_base_addr = ioremap(addr, 16); - - if (!pit_base_addr) - panic(pr_fmt("Impossible to ioremap PIT\n")); -} |