Merge tag 'soc-fixes-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC DT and driver fixes from Arnd Bergmann:
 "Lots of dts fixes for Qualcomm Snapdragon and NXP i.MX platforms,
  including:

   - A regression fix for SDHCI controllers on Inforce 6540, and another
     SDHCI fix on SM8350

   - Reenable cluster idle on sm8250 after the the code fix is upstream

   - multiple fixes for the QMP PHY binding, needing an incompatible dt
     change

   - The reserved memory map is updated on Xiaomi Mi 4C and Huawei Nexus
     6P, to avoid instabilities caused by use of protected memory
     regions

   - Fix i.MX8MP DT for missing GPC Interrupt, power-domain typo and USB
     clock error

   - A couple of verdin-imx8mm DT fixes for audio playback support

   - Fix pca9547 i2c-mux node name for i.MX and Vybrid device trees

   - Fix an imx93-11x11-evk uSDHC pad setting problem that causes Micron
     eMMC CMD8 CRC error in HS400ES/HS400 mode

  The remaining ARM and RISC-V platforms only have very few smaller dts
  bugfixes this time:

   - A fix for the SiFive unmatched board's PCI memory space

   - A revert to fix a regression with GPIO on Marvell Armada

   - A fix for the UART address on Marvell AC5

   - Missing chip-select phandles for stm32 boards

   - Selecting the correct clock for the sam9x60 memory controller

   - Amlogic based Odroid-HC4 needs a revert to restore USB
     functionality.

  And finally, there are some minor code fixes:

   - Build fixes for OMAP1, pxa, riscpc, raspberry pi firmware, and zynq
     firmware

   - memory controller driver fixes for an OMAP regression and older
     bugs on tegra, atmel and mvebu

   - reset controller fixes for ti-sci and uniphier platforms

   - ARM SCMI firmware fixes for a couple of rare corner cases

   - Qualcomm platform driver fixes for incorrect error handling and a
     backwards compatibility fix for the apr driver using older dtb

   - NXP i.MX SoC driver fixes for HDMI output, error handling in the
     imx8 soc-id and missing reference counting on older cpuid code"

* tag 'soc-fixes-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (60 commits)
  firmware: zynqmp: fix declarations for gcc-13
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp151a-prtt1l
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp157c-emstamp-argon
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp15xx-dhcom-som
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp15xx-dhcor-som
  ARM: dts: at91: sam9x60: fix the ddr clock for sam9x60
  ARM: omap1: fix building gpio15xx
  ARM: omap1: fix !ARCH_OMAP1_ANY link failures
  firmware: raspberrypi: Fix type assignment
  arm64: dts: qcom: msm8992-libra: Fix the memory map
  arm64: dts: qcom: msm8992: Don't use sfpb mutex
  PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
  arm64: dts: msm8994-angler: fix the memory map
  arm64: dts: marvell: AC5/AC5X: Fix address for UART1
  ARM: footbridge: drop unnecessary inclusion
  Revert "ARM: dts: armada-39x: Fix compatible string for gpios"
  Revert "ARM: dts: armada-38x: Fix compatible string for gpios"
  ARM: pxa: enable PXA310/PXA320 for DT-only build
  riscv: dts: sifive: fu740: fix size of pcie 32bit memory
  soc: qcom: apr: Make qcom,protection-domain optional again
  ...

61 files changed, 219 insertions, 218 deletions

diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 12933eff419f..446861b6b17b 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -304,7 +304,7 @@
 			};
 
 			gpio0: gpio@18100 {
-				compatible = "marvell,armadaxp-gpio",
+				compatible = "marvell,armada-370-gpio",
 					     "marvell,orion-gpio";
 				reg = <0x18100 0x40>, <0x181c0 0x08>;
 				reg-names = "gpio", "pwm";
@@ -323,7 +323,7 @@
 			};
 
 			gpio1: gpio@18140 {
-				compatible = "marvell,armadaxp-gpio",
+				compatible = "marvell,armada-370-gpio",
 					     "marvell,orion-gpio";
 				reg = <0x18140 0x40>, <0x181c8 0x08>;
 				reg-names = "gpio", "pwm";
diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
index 1e05208d9f34..9d1cac49c022 100644
--- a/arch/arm/boot/dts/armada-39x.dtsi
+++ b/arch/arm/boot/dts/armada-39x.dtsi
@@ -213,7 +213,7 @@
 			};
 
 			gpio0: gpio@18100 {
-				compatible = "marvell,armadaxp-gpio", "marvell,orion-gpio";
+				compatible = "marvell,orion-gpio";
 				reg = <0x18100 0x40>;
 				ngpios = <32>;
 				gpio-controller;
@@ -227,7 +227,7 @@
 			};
 
 			gpio1: gpio@18140 {
-				compatible = "marvell,armadaxp-gpio", "marvell,orion-gpio";
+				compatible = "marvell,orion-gpio";
 				reg = <0x18140 0x40>;
 				ngpios = <28>;
 				gpio-controller;
diff --git a/arch/arm/boot/dts/imx53-ppd.dts b/arch/arm/boot/dts/imx53-ppd.dts
index 37d0cffea99c..70c4a4852256 100644
--- a/arch/arm/boot/dts/imx53-ppd.dts
+++ b/arch/arm/boot/dts/imx53-ppd.dts
@@ -488,7 +488,7 @@
 	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
index 4bc4371e6bae..4b81a975c979 100644
--- a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
@@ -632,7 +632,6 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
 	rts-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6ul-pico-dwarf.dts b/arch/arm/boot/dts/imx6ul-pico-dwarf.dts
index 162dc259edc8..5a74c7f68eb6 100644
--- a/arch/arm/boot/dts/imx6ul-pico-dwarf.dts
+++ b/arch/arm/boot/dts/imx6ul-pico-dwarf.dts
@@ -32,7 +32,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx7d-pico-dwarf.dts b/arch/arm/boot/dts/imx7d-pico-dwarf.dts
index 5162fe227d1e..fdc10563f147 100644
--- a/arch/arm/boot/dts/imx7d-pico-dwarf.dts
+++ b/arch/arm/boot/dts/imx7d-pico-dwarf.dts
@@ -32,7 +32,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -52,7 +52,7 @@
 };
 
 &i2c4 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx7d-pico-nymph.dts b/arch/arm/boot/dts/imx7d-pico-nymph.dts
index 104a85254adb..5afb1674e012 100644
--- a/arch/arm/boot/dts/imx7d-pico-nymph.dts
+++ b/arch/arm/boot/dts/imx7d-pico-nymph.dts
@@ -43,7 +43,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -64,7 +64,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
index 44cd72f1b1be..116e59a3b76d 100644
--- a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
+++ b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
@@ -19,16 +19,16 @@
 		serial@f995e000 {
 			status = "okay";
 		};
+	};
+};
 
-		sdhci@f9824900 {
-			bus-width = <8>;
-			non-removable;
-			status = "okay";
-		};
+&sdhc_1 {
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
 
-		sdhci@f98a4900 {
-			cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
-			bus-width = <4>;
-		};
-	};
+&sdhc_2 {
+	cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
 };
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index fe30abfff90a..4b0d2b4f4b6a 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -421,7 +421,7 @@
 			status = "disabled";
 		};
 
-		mmc@f9824900 {
+		sdhc_1: mmc@f9824900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
 			reg-names = "hc", "core";
@@ -434,7 +434,7 @@
 			status = "disabled";
 		};
 
-		mmc@f98a4900 {
+		sdhc_2: mmc@f98a4900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
 			reg-names = "hc", "core";
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index 8f5477e307dd..37a5d96aaf64 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -564,7 +564,7 @@
 			mpddrc: mpddrc@ffffe800 {
 				compatible = "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
 				reg = <0xffffe800 0x200>;
-				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 49>;
 				clock-names = "ddrck", "mpddr";
 			};
 
diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi b/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi
index d865ab5d866b..dd23de85100c 100644
--- a/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi
+++ b/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi
@@ -101,8 +101,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;
diff --git a/arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi b/arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi
index aef02e6421a3..7d11c50b9e40 100644
--- a/arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi
@@ -391,8 +391,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index 002f221f1694..c06edd2eacb0 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -428,8 +428,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
index 134a798ad3f2..bb40fb46da81 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -247,8 +247,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
 	#address-cells = <1>;
 	#size-cells = <0>;
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
index 42ed4a04a12e..6280c5e86a12 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
@@ -345,7 +345,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
index f892977da9e4..c00d39562a10 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
+++ b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
@@ -340,7 +340,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
diff --git a/arch/arm/mach-footbridge/isa-rtc.c b/arch/arm/mach-footbridge/isa-rtc.c
index b8f741a3a37e..237b828dd2f1 100644
--- a/arch/arm/mach-footbridge/isa-rtc.c
+++ b/arch/arm/mach-footbridge/isa-rtc.c
@@ -20,7 +20,6 @@
 
 #include <linux/init.h>
 #include <linux/mc146818rtc.h>
-#include <linux/bcd.h>
 #include <linux/io.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-imx/cpu-imx25.c b/arch/arm/mach-imx/cpu-imx25.c
index 3e63445cde06..cc86977d0a34 100644
--- a/arch/arm/mach-imx/cpu-imx25.c
+++ b/arch/arm/mach-imx/cpu-imx25.c
@@ -23,6 +23,7 @@ static int mx25_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx25-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 	rev = readl(iim_base + MXC_IIMSREV);
 	iounmap(iim_base);
diff --git a/arch/arm/mach-imx/cpu-imx27.c b/arch/arm/mach-imx/cpu-imx27.c
index bf70e13bbe9e..1d2893908368 100644
--- a/arch/arm/mach-imx/cpu-imx27.c
+++ b/arch/arm/mach-imx/cpu-imx27.c
@@ -28,6 +28,7 @@ static int mx27_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx27-ccm");
 	ccm_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!ccm_base);
 	/*
 	 * now we have access to the IO registers. As we need
diff --git a/arch/arm/mach-imx/cpu-imx31.c b/arch/arm/mach-imx/cpu-imx31.c
index b9c24b851d1a..35c544924e50 100644
--- a/arch/arm/mach-imx/cpu-imx31.c
+++ b/arch/arm/mach-imx/cpu-imx31.c
@@ -39,6 +39,7 @@ static int mx31_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx31-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 
 	/* read SREV register from IIM module */
diff --git a/arch/arm/mach-imx/cpu-imx35.c b/arch/arm/mach-imx/cpu-imx35.c
index 80e7d8ab9f1b..1fe75b39c2d9 100644
--- a/arch/arm/mach-imx/cpu-imx35.c
+++ b/arch/arm/mach-imx/cpu-imx35.c
@@ -21,6 +21,7 @@ static int mx35_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx35-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 
 	rev = imx_readl(iim_base + MXC_IIMSREV);
diff --git a/arch/arm/mach-imx/cpu-imx5.c b/arch/arm/mach-imx/cpu-imx5.c
index ad56263778f9..a67c89bf155d 100644
--- a/arch/arm/mach-imx/cpu-imx5.c
+++ b/arch/arm/mach-imx/cpu-imx5.c
@@ -28,6 +28,7 @@ static u32 imx5_read_srev_reg(const char *compat)
 
 	np = of_find_compatible_node(NULL, NULL, compat);
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	WARN_ON(!iim_base);
 
 	srev = readl(iim_base + IIM_SREV) & 0xff;
diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig
index 538a960257cc..7ec7ada287e0 100644
--- a/arch/arm/mach-omap1/Kconfig
+++ b/arch/arm/mach-omap1/Kconfig
@@ -4,6 +4,7 @@ menuconfig ARCH_OMAP1
 	depends on ARCH_MULTI_V4T || ARCH_MULTI_V5
 	depends on CPU_LITTLE_ENDIAN
 	depends on ATAGS
+	select ARCH_OMAP
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_OMAP
 	select CLKSRC_MMIO
@@ -45,10 +46,6 @@ config ARCH_OMAP16XX
 	select CPU_ARM926T
 	select OMAP_DM_TIMER
 
-config ARCH_OMAP1_ANY
-	select ARCH_OMAP
-	def_bool ARCH_OMAP730 || ARCH_OMAP850 || ARCH_OMAP15XX || ARCH_OMAP16XX
-
 config ARCH_OMAP
 	bool
 
diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile
index 506074b86333..0615cb0ba580 100644
--- a/arch/arm/mach-omap1/Makefile
+++ b/arch/arm/mach-omap1/Makefile
@@ -3,8 +3,6 @@
 # Makefile for the linux kernel.
 #
 
-ifdef CONFIG_ARCH_OMAP1_ANY
-
 # Common support
 obj-y := io.o id.o sram-init.o sram.o time.o irq.o mux.o flash.o \
 	 serial.o devices.o dma.o omap-dma.o fb.o
@@ -59,5 +57,3 @@ obj-$(CONFIG_ARCH_OMAP730)		+= gpio7xx.o
 obj-$(CONFIG_ARCH_OMAP850)		+= gpio7xx.o
 obj-$(CONFIG_ARCH_OMAP15XX)		+= gpio15xx.o
 obj-$(CONFIG_ARCH_OMAP16XX)		+= gpio16xx.o
-
-endif
diff --git a/arch/arm/mach-omap1/gpio15xx.c b/arch/arm/mach-omap1/gpio15xx.c
index c675f11de99d..61fa26efd865 100644
--- a/arch/arm/mach-omap1/gpio15xx.c
+++ b/arch/arm/mach-omap1/gpio15xx.c
@@ -11,6 +11,7 @@
 #include <linux/gpio.h>
 #include <linux/platform_data/gpio-omap.h>
 #include <linux/soc/ti/omap1-soc.h>
+#include <asm/irq.h>
 
 #include "irqs.h"
 
diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c
index d2db9b8aed3f..0074b011a05a 100644
--- a/arch/arm/mach-omap1/io.c
+++ b/arch/arm/mach-omap1/io.c
@@ -22,17 +22,14 @@
  * The machine specific code may provide the extra mapping besides the
  * default mapping provided here.
  */
-static struct map_desc omap_io_desc[] __initdata = {
+#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
+static struct map_desc omap7xx_io_desc[] __initdata = {
 	{
 		.virtual	= OMAP1_IO_VIRT,
 		.pfn		= __phys_to_pfn(OMAP1_IO_PHYS),
 		.length		= OMAP1_IO_SIZE,
 		.type		= MT_DEVICE
-	}
-};
-
-#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
-static struct map_desc omap7xx_io_desc[] __initdata = {
+	},
 	{
 		.virtual	= OMAP7XX_DSP_BASE,
 		.pfn		= __phys_to_pfn(OMAP7XX_DSP_START),
@@ -50,6 +47,12 @@ static struct map_desc omap7xx_io_desc[] __initdata = {
 #ifdef CONFIG_ARCH_OMAP15XX
 static struct map_desc omap1510_io_desc[] __initdata = {
 	{
+		.virtual	= OMAP1_IO_VIRT,
+		.pfn		= __phys_to_pfn(OMAP1_IO_PHYS),
+		.length		= OMAP1_IO_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
 		.virtual	= OMAP1510_DSP_BASE,
 		.pfn		= __phys_to_pfn(OMAP1510_DSP_START),
 		.length		= OMAP1510_DSP_SIZE,
@@ -66,6 +69,12 @@ static struct map_desc omap1510_io_desc[] __initdata = {
 #if defined(CONFIG_ARCH_OMAP16XX)
 static struct map_desc omap16xx_io_desc[] __initdata = {
 	{
+		.virtual	= OMAP1_IO_VIRT,
+		.pfn		= __phys_to_pfn(OMAP1_IO_PHYS),
+		.length		= OMAP1_IO_SIZE,
+		.type		= MT_DEVICE
+	},
+	{
 		.virtual	= OMAP16XX_DSP_BASE,
 		.pfn		= __phys_to_pfn(OMAP16XX_DSP_START),
 		.length		= OMAP16XX_DSP_SIZE,
@@ -79,18 +88,9 @@ static struct map_desc omap16xx_io_desc[] __initdata = {
 };
 #endif
 
-/*
- * Maps common IO regions for omap1
- */
-static void __init omap1_map_common_io(void)
-{
-	iotable_init(omap_io_desc, ARRAY_SIZE(omap_io_desc));
-}
-
 #if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
 void __init omap7xx_map_io(void)
 {
-	omap1_map_common_io();
 	iotable_init(omap7xx_io_desc, ARRAY_SIZE(omap7xx_io_desc));
 }
 #endif
@@ -98,7 +98,6 @@ void __init omap7xx_map_io(void)
 #ifdef CONFIG_ARCH_OMAP15XX
 void __init omap15xx_map_io(void)
 {
-	omap1_map_common_io();
 	iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));
 }
 #endif
@@ -106,7 +105,6 @@ void __init omap15xx_map_io(void)
 #if defined(CONFIG_ARCH_OMAP16XX)
 void __init omap16xx_map_io(void)
 {
-	omap1_map_common_io();
 	iotable_init(omap16xx_io_desc, ARRAY_SIZE(omap16xx_io_desc));
 }
 #endif
diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c
index 05c25c432449..b1632cbe37e6 100644
--- a/arch/arm/mach-omap1/mcbsp.c
+++ b/arch/arm/mach-omap1/mcbsp.c
@@ -89,7 +89,6 @@ static struct omap_mcbsp_ops omap1_mcbsp_ops = {
 #define OMAP1610_MCBSP2_BASE	0xfffb1000
 #define OMAP1610_MCBSP3_BASE	0xe1017000
 
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
 struct resource omap7xx_mcbsp_res[][6] = {
 	{
 		{
@@ -159,14 +158,7 @@ static struct omap_mcbsp_platform_data omap7xx_mcbsp_pdata[] = {
 };
 #define OMAP7XX_MCBSP_RES_SZ		ARRAY_SIZE(omap7xx_mcbsp_res[1])
 #define OMAP7XX_MCBSP_COUNT		ARRAY_SIZE(omap7xx_mcbsp_res)
-#else
-#define omap7xx_mcbsp_res_0		NULL
-#define omap7xx_mcbsp_pdata		NULL
-#define OMAP7XX_MCBSP_RES_SZ		0
-#define OMAP7XX_MCBSP_COUNT		0
-#endif
 
-#ifdef CONFIG_ARCH_OMAP15XX
 struct resource omap15xx_mcbsp_res[][6] = {
 	{
 		{
@@ -266,14 +258,7 @@ static struct omap_mcbsp_platform_data omap15xx_mcbsp_pdata[] = {
 };
 #define OMAP15XX_MCBSP_RES_SZ		ARRAY_SIZE(omap15xx_mcbsp_res[1])
 #define OMAP15XX_MCBSP_COUNT		ARRAY_SIZE(omap15xx_mcbsp_res)
-#else
-#define omap15xx_mcbsp_res_0		NULL
-#define omap15xx_mcbsp_pdata		NULL
-#define OMAP15XX_MCBSP_RES_SZ		0
-#define OMAP15XX_MCBSP_COUNT		0
-#endif
 
-#ifdef CONFIG_ARCH_OMAP16XX
 struct resource omap16xx_mcbsp_res[][6] = {
 	{
 		{
@@ -373,12 +358,6 @@ static struct omap_mcbsp_platform_data omap16xx_mcbsp_pdata[] = {
 };
 #define OMAP16XX_MCBSP_RES_SZ		ARRAY_SIZE(omap16xx_mcbsp_res[1])
 #define OMAP16XX_MCBSP_COUNT		ARRAY_SIZE(omap16xx_mcbsp_res)
-#else
-#define omap16xx_mcbsp_res_0		NULL
-#define omap16xx_mcbsp_pdata		NULL
-#define OMAP16XX_MCBSP_RES_SZ		0
-#define OMAP16XX_MCBSP_COUNT		0
-#endif
 
 static void omap_mcbsp_register_board_cfg(struct resource *res, int res_count,
 			struct omap_mcbsp_platform_data *config, int size)
diff --git a/arch/arm/mach-omap1/pm.h b/arch/arm/mach-omap1/pm.h
index d9165709c532..0d1f092821ff 100644
--- a/arch/arm/mach-omap1/pm.h
+++ b/arch/arm/mach-omap1/pm.h
@@ -106,13 +106,6 @@
 #define OMAP7XX_IDLECT3		0xfffece24
 #define OMAP7XX_IDLE_LOOP_REQUEST	0x0C00
 
-#if     !defined(CONFIG_ARCH_OMAP730) && \
-	!defined(CONFIG_ARCH_OMAP850) && \
-	!defined(CONFIG_ARCH_OMAP15XX) && \
-	!defined(CONFIG_ARCH_OMAP16XX)
-#warning "Power management for this processor not implemented yet"
-#endif
-
 #ifndef __ASSEMBLER__
 
 #include <linux/clk.h>
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index b90d98bae68d..03e25af6f48c 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -45,6 +45,8 @@ config MACH_PXA27X_DT
 config MACH_PXA3XX_DT
 	bool "Support PXA3xx platforms from device tree"
 	select CPU_PXA300
+	select CPU_PXA310
+	select CPU_PXA320
 	select PINCTRL
 	select POWER_SUPPLY
 	select PXA3xx
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
index e3486f60645a..a1f0c38ccadd 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
@@ -131,10 +131,6 @@
 };
 
 &usb {
-	phys = <&usb2_phy1>;
-	phy-names = "usb2-phy1";
-};
-
-&usb2_phy0 {
-	status = "disabled";
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
index 5a8d85a7d161..bbdf989058ff 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
@@ -110,7 +110,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
index 9b726c2a4842..dda27ed7aaf2 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
@@ -89,7 +89,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
index b2fcbba60d3a..3b0ed9305f2b 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
@@ -88,7 +88,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts
index 41d8b15f25a5..aa52ff73ff9e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts
@@ -53,7 +53,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
index 1bfbce69cc8b..ee8e932628d1 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
@@ -136,7 +136,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
index ef6c8967533e..d4867d6cf47c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
@@ -245,7 +245,7 @@
 &i2c3 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9540";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
index f598669e742f..52c5a43b30a0 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
@@ -103,7 +103,7 @@
 
 &i2c0 {
 	status = "okay";
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
index 3d9647b3da14..537cecb13dd0 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
@@ -44,7 +44,7 @@
 
 &i2c0 {
 	status = "okay";
-	pca9547@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9547";
 		reg = <0x75>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi
index afb455210bd0..d32a52ab00a4 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi
@@ -54,7 +54,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
index 03266bd90a06..169f047fbca5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
@@ -120,7 +120,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeprom@0 {
@@ -316,7 +316,7 @@
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
 			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x41
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13              0x41
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
index 24f61db33eba..752f409a30b1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
@@ -275,7 +275,7 @@
 		compatible = "rohm,bd71847";
 		reg = <0x4b>;
 		#clock-cells = <0>;
-		clocks = <&clk_xtal32k 0>;
+		clocks = <&clk_xtal32k>;
 		clock-output-names = "clk-32k-out";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pmic>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts
index 74c09891600f..6357078185ed 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts
@@ -214,7 +214,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	i2cmux@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9540";
 		reg = <0x70>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
index 750a1f07ecb7..6433c205f8dd 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
@@ -771,6 +771,7 @@
 &usbotg2 {
 	dr_mode = "host";
 	vbus-supply = <&reg_usb2_vbus>;
+	over-current-active-low;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
index c2a5c2f7b204..7c3f5c54f040 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
@@ -9,6 +9,7 @@
 		simple-audio-card,bitclock-master = <&dailink_master>;
 		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,mclk-fs = <256>;
 		simple-audio-card,name = "imx8mm-wm8904";
 		simple-audio-card,routing =
 			"Headphone Jack", "HPOUTL",
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
index 73cc3fafa018..b2bcd2282170 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
@@ -11,6 +11,7 @@
 		simple-audio-card,bitclock-master = <&dailink_master>;
 		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,mclk-fs = <256>;
 		simple-audio-card,name = "imx8mm-nau8822";
 		simple-audio-card,routing =
 			"Headphones", "LHP",
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
index d4c7ca16abd0..f2d93437084b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
@@ -36,8 +36,8 @@
 
 	pcie0_refclk: pcie0-refclk {
 		compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <100000000>;
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
 	};
 
 	reg_can1_stby: regulator-can1-stby {
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
index 79b290a002c1..ecc4bce6db97 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
@@ -99,7 +99,6 @@
 
 		regulators {
 			buck1: BUCK1 {
-				regulator-compatible = "BUCK1";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <2187500>;
 				regulator-boot-on;
@@ -108,7 +107,6 @@
 			};
 
 			buck2: BUCK2 {
-				regulator-compatible = "BUCK2";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <2187500>;
 				regulator-boot-on;
@@ -119,7 +117,6 @@
 			};
 
 			buck4: BUCK4 {
-				regulator-compatible = "BUCK4";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -127,7 +124,6 @@
 			};
 
 			buck5: BUCK5 {
-				regulator-compatible = "BUCK5";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -135,7 +131,6 @@
 			};
 
 			buck6: BUCK6 {
-				regulator-compatible = "BUCK6";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -143,7 +138,6 @@
 			};
 
 			ldo1: LDO1 {
-				regulator-compatible = "LDO1";
 				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -151,7 +145,6 @@
 			};
 
 			ldo2: LDO2 {
-				regulator-compatible = "LDO2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1150000>;
 				regulator-boot-on;
@@ -159,7 +152,6 @@
 			};
 
 			ldo3: LDO3 {
-				regulator-compatible = "LDO3";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -167,13 +159,11 @@
 			};
 
 			ldo4: LDO4 {
-				regulator-compatible = "LDO4";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo5: LDO5 {
-				regulator-compatible = "LDO5";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 7a6e6221f421..03034b439c1f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -524,6 +524,7 @@
 				compatible = "fsl,imx8mp-gpc";
 				reg = <0x303a0000 0x1000>;
 				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-controller;
 				#interrupt-cells = <3>;
 
@@ -590,7 +591,7 @@
 						reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY2>;
 					};
 
-					pgc_hsiomix: power-domains@17 {
+					pgc_hsiomix: power-domain@17 {
 						#power-domain-cells = <0>;
 						reg = <IMX8MP_POWER_DOMAIN_HSIOMIX>;
 						clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
@@ -1297,7 +1298,7 @@
 			reg = <0x32f10100 0x8>,
 			      <0x381f0000 0x20>;
 			clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
-				 <&clk IMX8MP_CLK_USB_ROOT>;
+				 <&clk IMX8MP_CLK_USB_SUSP>;
 			clock-names = "hsio", "suspend";
 			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
@@ -1310,9 +1311,9 @@
 			usb_dwc3_0: usb@38100000 {
 				compatible = "snps,dwc3";
 				reg = <0x38100000 0x10000>;
-				clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+				clocks = <&clk IMX8MP_CLK_USB_ROOT>,
 					 <&clk IMX8MP_CLK_USB_CORE_REF>,
-					 <&clk IMX8MP_CLK_USB_ROOT>;
+					 <&clk IMX8MP_CLK_USB_SUSP>;
 				clock-names = "bus_early", "ref", "suspend";
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy0>, <&usb3_phy0>;
@@ -1339,7 +1340,7 @@
 			reg = <0x32f10108 0x8>,
 			      <0x382f0000 0x20>;
 			clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
-				 <&clk IMX8MP_CLK_USB_ROOT>;
+				 <&clk IMX8MP_CLK_USB_SUSP>;
 			clock-names = "hsio", "suspend";
 			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
@@ -1352,9 +1353,9 @@
 			usb_dwc3_1: usb@38200000 {
 				compatible = "snps,dwc3";
 				reg = <0x38200000 0x10000>;
-				clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+				clocks = <&clk IMX8MP_CLK_USB_ROOT>,
 					 <&clk IMX8MP_CLK_USB_CORE_REF>,
-					 <&clk IMX8MP_CLK_USB_ROOT>;
+					 <&clk IMX8MP_CLK_USB_SUSP>;
 				clock-names = "bus_early", "ref", "suspend";
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy1>, <&usb3_phy1>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index 9dda2a1554c3..8614c18b5998 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -133,7 +133,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	i2cmux@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c1_pca9546>;
@@ -216,7 +216,7 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
-	pca9546: i2cmux@70 {
+	pca9546: i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts b/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
index 5d5aa6537225..6e6182709d22 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
@@ -339,7 +339,7 @@
 	bus-width = <4>;
 	non-removable;
 	no-sd;
-	no-emmc;
+	no-mmc;
 	status = "okay";
 
 	brcmf: wifi@1 {
@@ -359,7 +359,7 @@
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	no-sdio;
-	no-emmc;
+	no-mmc;
 	disable-wp;
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index 07d8dd8160f6..afa883389456 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -61,7 +61,7 @@
 	pinctrl-0 = <&pinctrl_lpi2c1 &pinctrl_ioexp_rst>;
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9646", "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
index 69786c326db0..27f9a9f33134 100644
--- a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
@@ -74,7 +74,7 @@
 
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
-			MX93_PAD_SD1_CLK__USDHC1_CLK		0x17fe
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x15fe
 			MX93_PAD_SD1_CMD__USDHC1_CMD		0x13fe
 			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x13fe
 			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x13fe
@@ -84,7 +84,7 @@
 			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x13fe
 			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x13fe
 			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x13fe
-			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x17fe
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x15fe
 		>;
 	};
 
@@ -102,7 +102,7 @@
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX93_PAD_SD2_CLK__USDHC2_CLK		0x17fe
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x15fe
 			MX93_PAD_SD2_CMD__USDHC2_CMD		0x13fe
 			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x13fe
 			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x13fe
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
index 7308f7b6b22c..8bce64069138 100644
--- a/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
@@ -98,7 +98,7 @@
 
 			uart1: serial@12100 {
 				compatible = "snps,dw-apb-uart";
-				reg = <0x11000 0x100>;
+				reg = <0x12100 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 				reg-io-width = <1>;
diff --git a/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi
index 87c90e93667f..79de9cc395c4 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi
@@ -3,6 +3,7 @@
  * Copyright (c) 2015, LGE Inc. All rights reserved.
  * Copyright (c) 2016, The Linux Foundation. All rights reserved.
  * Copyright (c) 2021, Petr Vorel <petr.vorel@gmail.com>
+ * Copyright (c) 2022, Dominik Kobinski <dominikkobinski314@gmail.com>
  */
 
 /dts-v1/;
@@ -51,6 +52,11 @@
 			reg = <0 0x03400000 0 0x1200000>;
 			no-map;
 		};
+
+		removed_region: reserved@5000000 {
+			reg = <0 0x05000000 0 0x2200000>;
+			no-map;
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
index b242c272d2af..fcca1ba94da6 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
+++ b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
@@ -11,6 +11,12 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/gpio-keys.h>
 
+/delete-node/ &adsp_mem;
+/delete-node/ &audio_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &peripheral_region;
+/delete-node/ &rmtfs_mem;
+
 / {
 	model = "Xiaomi Mi 4C";
 	compatible = "xiaomi,libra", "qcom,msm8992";
@@ -70,25 +76,67 @@
 		#size-cells = <2>;
 		ranges;
 
-		/* This is for getting crash logs using Android downstream kernels */
-		ramoops@dfc00000 {
-			compatible = "ramoops";
-			reg = <0x0 0xdfc00000 0x0 0x40000>;
-			console-size = <0x10000>;
-			record-size = <0x10000>;
-			ftrace-size = <0x10000>;
-			pmsg-size = <0x20000>;
+		memory_hole: hole@6400000 {
+			reg = <0 0x06400000 0 0x600000>;
+			no-map;
+		};
+
+		memory_hole2: hole2@6c00000 {
+			reg = <0 0x06c00000 0 0x2400000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@9000000 {
+			reg = <0 0x09000000 0 0x5a00000>;
+			no-map;
+		};
+
+		tzapp: tzapp@ea00000 {
+			reg = <0 0x0ea00000 0 0x1900000>;
+			no-map;
+		};
+
+		mdm_rfsa_mem: mdm-rfsa@ca0b0000 {
+			reg = <0 0xca0b0000 0 0x10000>;
+			no-map;
+		};
+
+		rmtfs_mem: rmtfs@ca100000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xca100000 0 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
 		};
 
-		modem_region: modem_region@9000000 {
-			reg = <0x0 0x9000000 0x0 0x5a00000>;
+		audio_mem: audio@cb400000 {
+			reg = <0 0xcb000000 0 0x400000>;
+			no-mem;
+		};
+
+		qseecom_mem: qseecom@cb400000 {
+			reg = <0 0xcb400000 0 0x1c00000>;
+			no-mem;
+		};
+
+		adsp_rfsa_mem: adsp-rfsa@cd000000 {
+			reg = <0 0xcd000000 0 0x10000>;
 			no-map;
 		};
 
-		tzapp: modem_region@ea00000 {
-			reg = <0x0 0xea00000 0x0 0x1900000>;
+		sensor_rfsa_mem: sensor-rfsa@cd010000 {
+			reg = <0 0xcd010000 0 0x10000>;
 			no-map;
 		};
+
+		ramoops@dfc00000 {
+			compatible = "ramoops";
+			reg = <0 0xdfc00000 0 0x40000>;
+			console-size = <0x10000>;
+			record-size = <0x10000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x20000>;
+		};
 	};
 };
 
@@ -130,11 +178,6 @@
 	status = "okay";
 };
 
-&peripheral_region {
-	reg = <0x0 0x7400000 0x0 0x1c00000>;
-	no-map;
-};
-
 &pm8994_spmi_regulators {
 	VDD_APC0: s8 {
 		regulator-min-microvolt = <680000>;
diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
index 10adb4986ef1..02fc3795dbfd 100644
--- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -37,10 +37,6 @@
 	compatible = "qcom,rpmcc-msm8992", "qcom,rpmcc";
 };
 
-&tcsr_mutex {
-	compatible = "qcom,sfpb-mutex";
-};
-
 &timer {
 	interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
diff --git a/arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts
index 85abff0e9b3f..7b0f62144c3e 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts
@@ -9,9 +9,6 @@
 
 #include "msm8994.dtsi"
 
-/* Angler's firmware does not report where the memory is allocated */
-/delete-node/ &cont_splash_mem;
-
 / {
 	model = "Huawei Nexus 6P";
 	compatible = "huawei,angler", "qcom,msm8994";
@@ -28,6 +25,22 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		tzapp_mem: tzapp@4800000 {
+			reg = <0 0x04800000 0 0x1900000>;
+			no-map;
+		};
+
+		removed_region: reserved@6300000 {
+			reg = <0 0x06300000 0 0xD00000>;
+			no-map;
+		};
+	};
 };
 
 &blsp1_uart2 {
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index 109c9d2b684d..71cf81a8eb4d 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -10,6 +10,7 @@
 #include <dt-bindings/interconnect/qcom,sc8280xp.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/phy/phy-qcom-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -762,7 +763,7 @@
 				 <0>,
 				 <0>,
 				 <0>,
-				 <&usb_0_ssphy>,
+				 <&usb_0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
 				 <0>,
 				 <0>,
 				 <0>,
@@ -770,7 +771,7 @@
 				 <0>,
 				 <0>,
 				 <0>,
-				 <&usb_1_ssphy>,
+				 <&usb_1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
 				 <0>,
 				 <0>,
 				 <0>,
@@ -1673,42 +1674,26 @@
 			};
 		};
 
-		usb_0_qmpphy: phy-wrapper@88ec000 {
+		usb_0_qmpphy: phy@88eb000 {
 			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
-			reg = <0 0x088ec000 0 0x1e4>,
-			      <0 0x088eb000 0 0x40>,
-			      <0 0x088ed000 0 0x1c8>;
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			reg = <0 0x088eb000 0 0x4000>;
 
 			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
-				 <&rpmhcc RPMH_CXO_CLK>,
 				 <&gcc GCC_USB4_EUD_CLKREF_CLK>,
-				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
-			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
 
 			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
-				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
+				 <&gcc GCC_USB4_DP_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			power-domains = <&gcc USB30_PRIM_GDSC>;
+			#clock-cells = <1>;
+			#phy-cells = <1>;
 
 			status = "disabled";
-
-			usb_0_ssphy: usb3-phy@88eb400 {
-				reg = <0 0x088eb400 0 0x100>,
-				      <0 0x088eb600 0 0x3ec>,
-				      <0 0x088ec400 0 0x364>,
-				      <0 0x088eba00 0 0x100>,
-				      <0 0x088ebc00 0 0x3ec>,
-				      <0 0x088ec200 0 0x18>;
-				#phy-cells = <0>;
-				#clock-cells = <0>;
-				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb0_phy_pipe_clk_src";
-			};
 		};
 
 		usb_1_hsphy: phy@8902000 {
@@ -1725,42 +1710,26 @@
 			status = "disabled";
 		};
 
-		usb_1_qmpphy: phy-wrapper@8904000 {
+		usb_1_qmpphy: phy@8903000 {
 			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
-			reg = <0 0x08904000 0 0x1e4>,
-			      <0 0x08903000 0 0x40>,
-			      <0 0x08905000 0 0x1c8>;
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			reg = <0 0x08903000 0 0x4000>;
 
 			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
-				 <&rpmhcc RPMH_CXO_CLK>,
 				 <&gcc GCC_USB4_CLKREF_CLK>,
-				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
-			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+			power-domains = <&gcc USB30_SEC_GDSC>;
 
 			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
 				 <&gcc GCC_USB4_1_DP_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			power-domains = <&gcc USB30_SEC_GDSC>;
+			#clock-cells = <1>;
+			#phy-cells = <1>;
 
 			status = "disabled";
-
-			usb_1_ssphy: usb3-phy@8903400 {
-				reg = <0 0x08903400 0 0x100>,
-				      <0 0x08903600 0 0x3ec>,
-				      <0 0x08904400 0 0x364>,
-				      <0 0x08903a00 0 0x100>,
-				      <0 0x08903c00 0 0x3ec>,
-				      <0 0x08904200 0 0x18>;
-				#phy-cells = <0>;
-				#clock-cells = <0>;
-				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb1_phy_pipe_clk_src";
-			};
 		};
 
 		pmu@9091000 {
@@ -1910,7 +1879,7 @@
 				reg = <0 0x0a600000 0 0xcd00>;
 				interrupts = <GIC_SPI 803 IRQ_TYPE_LEVEL_HIGH>;
 				iommus = <&apps_smmu 0x820 0x0>;
-				phys = <&usb_0_hsphy>, <&usb_0_ssphy>;
+				phys = <&usb_0_hsphy>, <&usb_0_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
 			};
 		};
@@ -1964,7 +1933,7 @@
 				reg = <0 0x0a800000 0 0xcd00>;
 				interrupts = <GIC_SPI 810 IRQ_TYPE_LEVEL_HIGH>;
 				iommus = <&apps_smmu 0x860 0x0>;
-				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
 			};
 		};
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index dab5579946f3..927032863e2f 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -334,7 +334,6 @@
 				exit-latency-us = <6562>;
 				min-residency-us = <9987>;
 				local-timer-stop;
-				status = "disabled";
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 245dce24ec59..fb3cd20a82b5 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -2382,8 +2382,8 @@
 				 <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "iface", "core", "xo";
 			resets = <&gcc GCC_SDCC2_BCR>;
-			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
-					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
+			interconnects = <&aggre2_noc MASTER_SDCC_2 &mc_virt SLAVE_EBI1>,
+					<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_SDCC_2>;
 			interconnect-names = "sdhc-ddr","cpu-sdhc";
 			iommus = <&apps_smmu 0x4a0 0x0>;
 			power-domains = <&rpmhpd SM8350_CX>;
diff --git a/arch/riscv/boot/dts/sifive/fu740-c000.dtsi b/arch/riscv/boot/dts/sifive/fu740-c000.dtsi
index 43bed6c0a84f..5235fd1c9cb6 100644
--- a/arch/riscv/boot/dts/sifive/fu740-c000.dtsi
+++ b/arch/riscv/boot/dts/sifive/fu740-c000.dtsi
@@ -328,7 +328,7 @@
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000  0x0 0x60080000  0x0 0x60080000 0x0 0x10000>,      /* I/O */
 				 <0x82000000  0x0 0x60090000  0x0 0x60090000 0x0 0xff70000>,    /* mem */
-				 <0x82000000  0x0 0x70000000  0x0 0x70000000 0x0 0x1000000>,    /* mem */
+				 <0x82000000  0x0 0x70000000  0x0 0x70000000 0x0 0x10000000>,    /* mem */
 				 <0xc3000000 0x20 0x00000000 0x20 0x00000000 0x20 0x00000000>;  /* mem prefetchable */
 			num-lanes = <0x8>;
 			interrupts = <56>, <57>, <58>, <59>, <60>, <61>, <62>, <63>, <64>;