Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for ARM SoCs.

  A slew of changes this release cycle.  The reset driver tree, that we
  merge through arm-soc for historical reasons, is also sizable this
  time around.

  Among the changes:

   - clps711x: Treewide changes to compatible strings, merged here for simplicity.
   - Qualcomm: SCM firmware driver cleanups, move to platform driver
   - ux500: Major cleanups, removal of old mach-specific infrastructure.
   - Atmel external bus memory driver
   - Move of brcmstb platform to the rest of bcm
   - PMC driver updates for tegra, various fixes and improvements
   - Samsung platform driver updates to support 64-bit Exynos platforms
   - Reset controller cleanups moving to devm_reset_controller_register() APIs
   - Reset controller driver for Amlogic Meson
   - Reset controller driver for Hisilicon hi6220
   - ARM SCPI power domain support"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
  ARM: ux500: consolidate base platform files
  ARM: ux500: move soc_id driver to drivers/soc
  ARM: ux500: call ux500_setup_id later
  ARM: ux500: consolidate soc_device code in id.c
  ARM: ux500: remove cpu_is_u* helpers
  ARM: ux500: use CLK_OF_DECLARE()
  ARM: ux500: move l2x0 init to .init_irq
  mfd: db8500 stop passing around platform data
  ASoC: ab8500-codec: remove platform data based probe
  ARM: ux500: move ab8500_regulator_plat_data into driver
  ARM: ux500: remove unused regulator data
  soc: raspberrypi-power: add CONFIG_OF dependency
  firmware: scpi: add CONFIG_OF dependency
  video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
  input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
  pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
  serial: clps711x: Changing the compatibility string to match with the smallest supported chip
  irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
  clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
  clk: clps711x: Changing the compatibility string to match with the smallest supported chip
  ...

10 files changed, 90 insertions, 1632 deletions

diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index edfff1ae1f8d..56d0eb6e254e 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -2,11 +2,9 @@
 # Makefile for the linux kernel, U8500 machine.
 #
 
-obj-y				:= cpu.o id.o pm.o
-obj-$(CONFIG_CACHE_L2X0)	+= cache-l2x0.o
+obj-y				:= pm.o
 obj-$(CONFIG_UX500_SOC_DB8500)	+= cpu-db8500.o
-obj-$(CONFIG_MACH_MOP500)	+= board-mop500-regulators.o \
-				board-mop500-audio.o
+obj-$(CONFIG_MACH_MOP500)	+= board-mop500-audio.o
 obj-$(CONFIG_SMP)		+= platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
 obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o
diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c b/arch/arm/mach-ux500/board-mop500-regulators.c
deleted file mode 100644
index 32d744e91ec2..000000000000
--- a/arch/arm/mach-ux500/board-mop500-regulators.c
+++ /dev/null
@@ -1,1065 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License Terms: GNU General Public License v2
- *
- * Authors: Sundar Iyer <sundar.iyer@stericsson.com>
- *          Bengt Jonsson <bengt.g.jonsson@stericsson.com>
- *          Daniel Willerud <daniel.willerud@stericsson.com>
- *
- * MOP500 board specific initialization for regulators
- */
-#include <linux/kernel.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/ab8500.h>
-#include "board-mop500-regulators.h"
-#include "id.h"
-
-static struct regulator_consumer_supply gpio_en_3v3_consumers[] = {
-       REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-struct regulator_init_data gpio_en_3v3_regulator = {
-       .constraints = {
-               .name = "EN-3V3",
-               .min_uV = 3300000,
-               .max_uV = 3300000,
-               .valid_ops_mask = REGULATOR_CHANGE_STATUS,
-       },
-       .num_consumer_supplies = ARRAY_SIZE(gpio_en_3v3_consumers),
-       .consumer_supplies = gpio_en_3v3_consumers,
-};
-
-/*
- * TPS61052 regulator
- */
-static struct regulator_consumer_supply tps61052_vaudio_consumers[] = {
-	/*
-	 * Boost converter supply to raise voltage on audio speaker, this
-	 * is actually connected to three pins, VInVhfL (left amplifier)
-	 * VInVhfR (right amplifier) and VIntDClassInt - all three must
-	 * be connected to the same voltage.
-	 */
-	REGULATOR_SUPPLY("vintdclassint", "ab8500-codec.0"),
-};
-
-struct regulator_init_data tps61052_regulator = {
-	.constraints = {
-		.name = "vaudio-hf",
-		.min_uV = 4500000,
-		.max_uV = 4500000,
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(tps61052_vaudio_consumers),
-	.consumer_supplies = tps61052_vaudio_consumers,
-};
-
-static struct regulator_consumer_supply ab8500_vaux1_consumers[] = {
-	/* Main display, u8500 R3 uib */
-	REGULATOR_SUPPLY("vddi", "mcde_disp_sony_acx424akp.0"),
-	/* Main display, u8500 uib and ST uib */
-	REGULATOR_SUPPLY("vdd1", "samsung_s6d16d0.0"),
-	/* Secondary display, ST uib */
-	REGULATOR_SUPPLY("vdd1", "samsung_s6d16d0.1"),
-	/* SFH7741 proximity sensor */
-	REGULATOR_SUPPLY("vcc", "gpio-keys.0"),
-	/* BH1780GLS ambient light sensor */
-	REGULATOR_SUPPLY("vcc", "2-0029"),
-	/* lsm303dlh accelerometer */
-	REGULATOR_SUPPLY("vdd", "2-0018"),
-	/* lsm303dlhc accelerometer */
-	REGULATOR_SUPPLY("vdd", "2-0019"),
-	/* lsm303dlh magnetometer */
-	REGULATOR_SUPPLY("vdd", "2-001e"),
-	/* Rohm BU21013 Touchscreen devices */
-	REGULATOR_SUPPLY("avdd", "3-005c"),
-	REGULATOR_SUPPLY("avdd", "3-005d"),
-	/* Synaptics RMI4 Touchscreen device */
-	REGULATOR_SUPPLY("vdd", "3-004b"),
-	/* L3G4200D Gyroscope device */
-	REGULATOR_SUPPLY("vdd", "2-0068"),
-	/* Ambient light sensor device */
-	REGULATOR_SUPPLY("vdd", "3-0029"),
-	/* Pressure sensor device */
-	REGULATOR_SUPPLY("vdd", "2-005c"),
-	/* Cypress TrueTouch Touchscreen device */
-	REGULATOR_SUPPLY("vcpin", "spi8.0"),
-	/* Camera device */
-	REGULATOR_SUPPLY("vaux12v5", "mmio_camera"),
-};
-
-static struct regulator_consumer_supply ab8500_vaux2_consumers[] = {
-	/* On-board eMMC power */
-	REGULATOR_SUPPLY("vmmc", "sdi4"),
-	/* AB8500 audio codec */
-	REGULATOR_SUPPLY("vcc-N2158", "ab8500-codec.0"),
-	/* AB8500 accessory detect 1 */
-	REGULATOR_SUPPLY("vcc-N2158", "ab8500-acc-det.0"),
-	/* AB8500 Tv-out device */
-	REGULATOR_SUPPLY("vcc-N2158", "mcde_tv_ab8500.4"),
-	/* AV8100 HDMI device */
-	REGULATOR_SUPPLY("vcc-N2158", "av8100_hdmi.3"),
-};
-
-static struct regulator_consumer_supply ab8500_vaux3_consumers[] = {
-	REGULATOR_SUPPLY("v-SD-STM", "stm"),
-	/* External MMC slot power */
-	REGULATOR_SUPPLY("vmmc", "sdi0"),
-};
-
-static struct regulator_consumer_supply ab8505_vaux4_consumers[] = {
-};
-
-static struct regulator_consumer_supply ab8505_vaux5_consumers[] = {
-};
-
-static struct regulator_consumer_supply ab8505_vaux6_consumers[] = {
-};
-
-static struct regulator_consumer_supply ab8505_vaux8_consumers[] = {
-	/* AB8500 audio codec device */
-	REGULATOR_SUPPLY("v-aux8", NULL),
-};
-
-static struct regulator_consumer_supply ab8505_vadc_consumers[] = {
-	/* Internal general-purpose ADC */
-	REGULATOR_SUPPLY("vddadc", "ab8500-gpadc.0"),
-	/* ADC for charger */
-	REGULATOR_SUPPLY("vddadc", "ab8500-charger.0"),
-};
-
-static struct regulator_consumer_supply ab8500_vtvout_consumers[] = {
-	/* TV-out DENC supply */
-	REGULATOR_SUPPLY("vtvout", "ab8500-denc.0"),
-	/* Internal general-purpose ADC */
-	REGULATOR_SUPPLY("vddadc", "ab8500-gpadc.0"),
-	/* ADC for charger */
-	REGULATOR_SUPPLY("vddadc", "ab8500-charger.0"),
-	/* AB8500 Tv-out device */
-	REGULATOR_SUPPLY("vtvout", "mcde_tv_ab8500.4"),
-};
-
-static struct regulator_consumer_supply ab8500_vaud_consumers[] = {
-	/* AB8500 audio-codec main supply */
-	REGULATOR_SUPPLY("vaud", "ab8500-codec.0"),
-};
-
-static struct regulator_consumer_supply ab8500_vamic1_consumers[] = {
-	/* AB8500 audio-codec Mic1 supply */
-	REGULATOR_SUPPLY("vamic1", "ab8500-codec.0"),
-};
-
-static struct regulator_consumer_supply ab8500_vamic2_consumers[] = {
-	/* AB8500 audio-codec Mic2 supply */
-	REGULATOR_SUPPLY("vamic2", "ab8500-codec.0"),
-};
-
-static struct regulator_consumer_supply ab8500_vdmic_consumers[] = {
-	/* AB8500 audio-codec DMic supply */
-	REGULATOR_SUPPLY("vdmic", "ab8500-codec.0"),
-};
-
-static struct regulator_consumer_supply ab8500_vintcore_consumers[] = {
-	/* SoC core supply, no device */
-	REGULATOR_SUPPLY("v-intcore", NULL),
-	/* USB Transceiver */
-	REGULATOR_SUPPLY("vddulpivio18", "ab8500-usb.0"),
-	/* Handled by abx500 clk driver */
-	REGULATOR_SUPPLY("v-intcore", "abx500-clk.0"),
-};
-
-static struct regulator_consumer_supply ab8505_usb_consumers[] = {
-	/* HS USB OTG physical interface */
-	REGULATOR_SUPPLY("v-ape", NULL),
-};
-
-static struct regulator_consumer_supply ab8500_vana_consumers[] = {
-	/* DB8500 DSI */
-	REGULATOR_SUPPLY("vdddsi1v2", "mcde"),
-	REGULATOR_SUPPLY("vdddsi1v2", "b2r2_core"),
-	REGULATOR_SUPPLY("vdddsi1v2", "b2r2_1_core"),
-	REGULATOR_SUPPLY("vdddsi1v2", "dsilink.0"),
-	REGULATOR_SUPPLY("vdddsi1v2", "dsilink.1"),
-	REGULATOR_SUPPLY("vdddsi1v2", "dsilink.2"),
-	/* DB8500 CSI */
-	REGULATOR_SUPPLY("vddcsi1v2", "mmio_camera"),
-};
-
-/* ab8500 regulator register initialization */
-static struct ab8500_regulator_reg_init ab8500_reg_init[] = {
-	/*
-	 * VanaRequestCtrl          = HP/LP depending on VxRequest
-	 * VextSupply1RequestCtrl   = HP/LP depending on VxRequest
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL2,       0xf0, 0x00),
-	/*
-	 * VextSupply2RequestCtrl   = HP/LP depending on VxRequest
-	 * VextSupply3RequestCtrl   = HP/LP depending on VxRequest
-	 * Vaux1RequestCtrl         = HP/LP depending on VxRequest
-	 * Vaux2RequestCtrl         = HP/LP depending on VxRequest
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL3,       0xff, 0x00),
-	/*
-	 * Vaux3RequestCtrl         = HP/LP depending on VxRequest
-	 * SwHPReq                  = Control through SWValid disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL4,       0x07, 0x00),
-	/*
-	 * VanaSysClkReq1HPValid    = disabled
-	 * Vaux1SysClkReq1HPValid   = disabled
-	 * Vaux2SysClkReq1HPValid   = disabled
-	 * Vaux3SysClkReq1HPValid   = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID1, 0xe8, 0x00),
-	/*
-	 * VextSupply1SysClkReq1HPValid = disabled
-	 * VextSupply2SysClkReq1HPValid = disabled
-	 * VextSupply3SysClkReq1HPValid = SysClkReq1 controlled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID2, 0x70, 0x40),
-	/*
-	 * VanaHwHPReq1Valid        = disabled
-	 * Vaux1HwHPreq1Valid       = disabled
-	 * Vaux2HwHPReq1Valid       = disabled
-	 * Vaux3HwHPReqValid        = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID1,     0xe8, 0x00),
-	/*
-	 * VextSupply1HwHPReq1Valid = disabled
-	 * VextSupply2HwHPReq1Valid = disabled
-	 * VextSupply3HwHPReq1Valid = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID2,     0x07, 0x00),
-	/*
-	 * VanaHwHPReq2Valid        = disabled
-	 * Vaux1HwHPReq2Valid       = disabled
-	 * Vaux2HwHPReq2Valid       = disabled
-	 * Vaux3HwHPReq2Valid       = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID1,     0xe8, 0x00),
-	/*
-	 * VextSupply1HwHPReq2Valid = disabled
-	 * VextSupply2HwHPReq2Valid = disabled
-	 * VextSupply3HwHPReq2Valid = HWReq2 controlled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID2,     0x07, 0x04),
-	/*
-	 * VanaSwHPReqValid         = disabled
-	 * Vaux1SwHPReqValid        = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID1,      0xa0, 0x00),
-	/*
-	 * Vaux2SwHPReqValid        = disabled
-	 * Vaux3SwHPReqValid        = disabled
-	 * VextSupply1SwHPReqValid  = disabled
-	 * VextSupply2SwHPReqValid  = disabled
-	 * VextSupply3SwHPReqValid  = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID2,      0x1f, 0x00),
-	/*
-	 * SysClkReq2Valid1         = SysClkReq2 controlled
-	 * SysClkReq3Valid1         = disabled
-	 * SysClkReq4Valid1         = SysClkReq4 controlled
-	 * SysClkReq5Valid1         = disabled
-	 * SysClkReq6Valid1         = SysClkReq6 controlled
-	 * SysClkReq7Valid1         = disabled
-	 * SysClkReq8Valid1         = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID1,    0xfe, 0x2a),
-	/*
-	 * SysClkReq2Valid2         = disabled
-	 * SysClkReq3Valid2         = disabled
-	 * SysClkReq4Valid2         = disabled
-	 * SysClkReq5Valid2         = disabled
-	 * SysClkReq6Valid2         = SysClkReq6 controlled
-	 * SysClkReq7Valid2         = disabled
-	 * SysClkReq8Valid2         = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID2,    0xfe, 0x20),
-	/*
-	 * VTVoutEna                = disabled
-	 * Vintcore12Ena            = disabled
-	 * Vintcore12Sel            = 1.25 V
-	 * Vintcore12LP             = inactive (HP)
-	 * VTVoutLP                 = inactive (HP)
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUMISC1,              0xfe, 0x10),
-	/*
-	 * VaudioEna                = disabled
-	 * VdmicEna                 = disabled
-	 * Vamic1Ena                = disabled
-	 * Vamic2Ena                = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VAUDIOSUPPLY,           0x1e, 0x00),
-	/*
-	 * Vamic1_dzout             = high-Z when Vamic1 is disabled
-	 * Vamic2_dzout             = high-Z when Vamic2 is disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUCTRL1VAMIC,         0x03, 0x00),
-	/*
-	 * VPll                     = Hw controlled (NOTE! PRCMU bits)
-	 * VanaRegu                 = force off
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VPLLVANAREGU,           0x0f, 0x02),
-	/*
-	 * VrefDDREna               = disabled
-	 * VrefDDRSleepMode         = inactive (no pulldown)
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VREFDDR,                0x03, 0x00),
-	/*
-	 * VextSupply1Regu          = force LP
-	 * VextSupply2Regu          = force OFF
-	 * VextSupply3Regu          = force HP (-> STBB2=LP and TPS=LP)
-	 * ExtSupply2Bypass         = ExtSupply12LPn ball is 0 when Ena is 0
-	 * ExtSupply3Bypass         = ExtSupply3LPn ball is 0 when Ena is 0
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU,          0xff, 0x13),
-	/*
-	 * Vaux1Regu                = force HP
-	 * Vaux2Regu                = force off
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VAUX12REGU,             0x0f, 0x01),
-	/*
-	 * Vaux3Regu                = force off
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3REGU,          0x03, 0x00),
-	/*
-	 * Vaux1Sel                 = 2.8 V
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VAUX1SEL,               0x0f, 0x0C),
-	/*
-	 * Vaux2Sel                 = 2.9 V
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VAUX2SEL,               0x0f, 0x0d),
-	/*
-	 * Vaux3Sel                 = 2.91 V
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3SEL,           0x07, 0x07),
-	/*
-	 * VextSupply12LP           = disabled (no LP)
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUCTRL2SPARE,         0x01, 0x00),
-	/*
-	 * Vaux1Disch               = short discharge time
-	 * Vaux2Disch               = short discharge time
-	 * Vaux3Disch               = short discharge time
-	 * Vintcore12Disch          = short discharge time
-	 * VTVoutDisch              = short discharge time
-	 * VaudioDisch              = short discharge time
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH,          0xfc, 0x00),
-	/*
-	 * VanaDisch                = short discharge time
-	 * VdmicPullDownEna         = pulldown disabled when Vdmic is disabled
-	 * VdmicDisch               = short discharge time
-	 */
-	INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH2,         0x16, 0x00),
-};
-
-/* AB8500 regulators */
-static struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
-	/* supplies to the display/camera */
-	[AB8500_LDO_AUX1] = {
-		.supply_regulator = "ab8500-ext-supply3",
-		.constraints = {
-			.name = "V-DISPLAY",
-			.min_uV = 2800000,
-			.max_uV = 3300000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS,
-			.boot_on = 1, /* display is on at boot */
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux1_consumers),
-		.consumer_supplies = ab8500_vaux1_consumers,
-	},
-	/* supplies to the on-board eMMC */
-	[AB8500_LDO_AUX2] = {
-		.supply_regulator = "ab8500-ext-supply3",
-		.constraints = {
-			.name = "V-eMMC1",
-			.min_uV = 1100000,
-			.max_uV = 3300000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux2_consumers),
-		.consumer_supplies = ab8500_vaux2_consumers,
-	},
-	/* supply for VAUX3, supplies to SDcard slots */
-	[AB8500_LDO_AUX3] = {
-		.supply_regulator = "ab8500-ext-supply3",
-		.constraints = {
-			.name = "V-MMC-SD",
-			.min_uV = 1100000,
-			.max_uV = 3300000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux3_consumers),
-		.consumer_supplies = ab8500_vaux3_consumers,
-	},
-	/* supply for tvout, gpadc, TVOUT LDO */
-	[AB8500_LDO_TVOUT] = {
-		.constraints = {
-			.name = "V-TVOUT",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vtvout_consumers),
-		.consumer_supplies = ab8500_vtvout_consumers,
-	},
-	/* supply for ab8500-vaudio, VAUDIO LDO */
-	[AB8500_LDO_AUDIO] = {
-		.constraints = {
-			.name = "V-AUD",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaud_consumers),
-		.consumer_supplies = ab8500_vaud_consumers,
-	},
-	/* supply for v-anamic1 VAMic1-LDO */
-	[AB8500_LDO_ANAMIC1] = {
-		.constraints = {
-			.name = "V-AMIC1",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vamic1_consumers),
-		.consumer_supplies = ab8500_vamic1_consumers,
-	},
-	/* supply for v-amic2, VAMIC2 LDO, reuse constants for AMIC1 */
-	[AB8500_LDO_ANAMIC2] = {
-		.constraints = {
-			.name = "V-AMIC2",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vamic2_consumers),
-		.consumer_supplies = ab8500_vamic2_consumers,
-	},
-	/* supply for v-dmic, VDMIC LDO */
-	[AB8500_LDO_DMIC] = {
-		.constraints = {
-			.name = "V-DMIC",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vdmic_consumers),
-		.consumer_supplies = ab8500_vdmic_consumers,
-	},
-	/* supply for v-intcore12, VINTCORE12 LDO */
-	[AB8500_LDO_INTCORE] = {
-		.constraints = {
-			.name = "V-INTCORE",
-			.min_uV = 1250000,
-			.max_uV = 1350000,
-			.input_uV = 1800000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE |
-					  REGULATOR_CHANGE_DRMS,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vintcore_consumers),
-		.consumer_supplies = ab8500_vintcore_consumers,
-	},
-	/* supply for U8500 CSI-DSI, VANA LDO */
-	[AB8500_LDO_ANA] = {
-		.constraints = {
-			.name = "V-CSI-DSI",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vana_consumers),
-		.consumer_supplies = ab8500_vana_consumers,
-	},
-};
-
-/* supply for VextSupply3 */
-static struct regulator_consumer_supply ab8500_ext_supply3_consumers[] = {
-	/* SIM supply for 3 V SIM cards */
-	REGULATOR_SUPPLY("vinvsim", "sim-detect.0"),
-};
-
-/* extended configuration for VextSupply2, only used for HREFP_V20 boards */
-static struct ab8500_ext_regulator_cfg ab8500_ext_supply2 = {
-	.hwreq = true,
-};
-
-/*
- * AB8500 external regulators
- */
-static struct regulator_init_data ab8500_ext_regulators[] = {
-	/* fixed Vbat supplies VSMPS1_EXT_1V8 */
-	[AB8500_EXT_SUPPLY1] = {
-		.constraints = {
-			.name = "ab8500-ext-supply1",
-			.min_uV = 1800000,
-			.max_uV = 1800000,
-			.initial_mode = REGULATOR_MODE_IDLE,
-			.boot_on = 1,
-			.always_on = 1,
-		},
-	},
-	/* fixed Vbat supplies VSMPS2_EXT_1V36 and VSMPS5_EXT_1V15 */
-	[AB8500_EXT_SUPPLY2] = {
-		.constraints = {
-			.name = "ab8500-ext-supply2",
-			.min_uV = 1360000,
-			.max_uV = 1360000,
-		},
-	},
-	/* fixed Vbat supplies VSMPS3_EXT_3V4 and VSMPS4_EXT_3V4 */
-	[AB8500_EXT_SUPPLY3] = {
-		.constraints = {
-			.name = "ab8500-ext-supply3",
-			.min_uV = 3400000,
-			.max_uV = 3400000,
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-			.boot_on = 1,
-		},
-		.num_consumer_supplies =
-			ARRAY_SIZE(ab8500_ext_supply3_consumers),
-		.consumer_supplies = ab8500_ext_supply3_consumers,
-	},
-};
-
-/* ab8505 regulator register initialization */
-static struct ab8500_regulator_reg_init ab8505_reg_init[] = {
-	/*
-	 * VarmRequestCtrl
-	 * VsmpsCRequestCtrl
-	 * VsmpsARequestCtrl
-	 * VsmpsBRequestCtrl
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL1,       0x00, 0x00),
-	/*
-	 * VsafeRequestCtrl
-	 * VpllRequestCtrl
-	 * VanaRequestCtrl          = HP/LP depending on VxRequest
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL2,       0x30, 0x00),
-	/*
-	 * Vaux1RequestCtrl         = HP/LP depending on VxRequest
-	 * Vaux2RequestCtrl         = HP/LP depending on VxRequest
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL3,       0xf0, 0x00),
-	/*
-	 * Vaux3RequestCtrl         = HP/LP depending on VxRequest
-	 * SwHPReq                  = Control through SWValid disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUREQUESTCTRL4,       0x07, 0x00),
-	/*
-	 * VsmpsASysClkReq1HPValid
-	 * VsmpsBSysClkReq1HPValid
-	 * VsafeSysClkReq1HPValid
-	 * VanaSysClkReq1HPValid    = disabled
-	 * VpllSysClkReq1HPValid
-	 * Vaux1SysClkReq1HPValid   = disabled
-	 * Vaux2SysClkReq1HPValid   = disabled
-	 * Vaux3SysClkReq1HPValid   = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQ1HPVALID1, 0xe8, 0x00),
-	/*
-	 * VsmpsCSysClkReq1HPValid
-	 * VarmSysClkReq1HPValid
-	 * VbbSysClkReq1HPValid
-	 * VsmpsMSysClkReq1HPValid
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQ1HPVALID2, 0x00, 0x00),
-	/*
-	 * VsmpsAHwHPReq1Valid
-	 * VsmpsBHwHPReq1Valid
-	 * VsafeHwHPReq1Valid
-	 * VanaHwHPReq1Valid        = disabled
-	 * VpllHwHPReq1Valid
-	 * Vaux1HwHPreq1Valid       = disabled
-	 * Vaux2HwHPReq1Valid       = disabled
-	 * Vaux3HwHPReqValid        = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ1VALID1,     0xe8, 0x00),
-	/*
-	 * VsmpsMHwHPReq1Valid
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ1VALID2,     0x00, 0x00),
-	/*
-	 * VsmpsAHwHPReq2Valid
-	 * VsmpsBHwHPReq2Valid
-	 * VsafeHwHPReq2Valid
-	 * VanaHwHPReq2Valid        = disabled
-	 * VpllHwHPReq2Valid
-	 * Vaux1HwHPReq2Valid       = disabled
-	 * Vaux2HwHPReq2Valid       = disabled
-	 * Vaux3HwHPReq2Valid       = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ2VALID1,     0xe8, 0x00),
-	/*
-	 * VsmpsMHwHPReq2Valid
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUHWHPREQ2VALID2,     0x00, 0x00),
-	/**
-	 * VsmpsCSwHPReqValid
-	 * VarmSwHPReqValid
-	 * VsmpsASwHPReqValid
-	 * VsmpsBSwHPReqValid
-	 * VsafeSwHPReqValid
-	 * VanaSwHPReqValid
-	 * VanaSwHPReqValid         = disabled
-	 * VpllSwHPReqValid
-	 * Vaux1SwHPReqValid        = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUSWHPREQVALID1,      0xa0, 0x00),
-	/*
-	 * Vaux2SwHPReqValid        = disabled
-	 * Vaux3SwHPReqValid        = disabled
-	 * VsmpsMSwHPReqValid
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUSWHPREQVALID2,      0x03, 0x00),
-	/*
-	 * SysClkReq2Valid1         = SysClkReq2 controlled
-	 * SysClkReq3Valid1         = disabled
-	 * SysClkReq4Valid1         = SysClkReq4 controlled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQVALID1,    0x0e, 0x0a),
-	/*
-	 * SysClkReq2Valid2         = disabled
-	 * SysClkReq3Valid2         = disabled
-	 * SysClkReq4Valid2         = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUSYSCLKREQVALID2,    0x0e, 0x00),
-	/*
-	 * Vaux4SwHPReqValid
-	 * Vaux4HwHPReq2Valid
-	 * Vaux4HwHPReq1Valid
-	 * Vaux4SysClkReq1HPValid
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUVAUX4REQVALID,    0x00, 0x00),
-	/*
-	 * VadcEna                  = disabled
-	 * VintCore12Ena            = disabled
-	 * VintCore12Sel            = 1.25 V
-	 * VintCore12LP             = inactive (HP)
-	 * VadcLP                   = inactive (HP)
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUMISC1,              0xfe, 0x10),
-	/*
-	 * VaudioEna                = disabled
-	 * Vaux8Ena                 = disabled
-	 * Vamic1Ena                = disabled
-	 * Vamic2Ena                = disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VAUDIOSUPPLY,           0x1e, 0x00),
-	/*
-	 * Vamic1_dzout             = high-Z when Vamic1 is disabled
-	 * Vamic2_dzout             = high-Z when Vamic2 is disabled
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUCTRL1VAMIC,         0x03, 0x00),
-	/*
-	 * VsmpsARegu
-	 * VsmpsASelCtrl
-	 * VsmpsAAutoMode
-	 * VsmpsAPWMMode
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSAREGU,    0x00, 0x00),
-	/*
-	 * VsmpsBRegu
-	 * VsmpsBSelCtrl
-	 * VsmpsBAutoMode
-	 * VsmpsBPWMMode
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSBREGU,    0x00, 0x00),
-	/*
-	 * VsafeRegu
-	 * VsafeSelCtrl
-	 * VsafeAutoMode
-	 * VsafePWMMode
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSAFEREGU,    0x00, 0x00),
-	/*
-	 * VPll                     = Hw controlled (NOTE! PRCMU bits)
-	 * VanaRegu                 = force off
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VPLLVANAREGU,           0x0f, 0x02),
-	/*
-	 * VextSupply1Regu          = force OFF (OTP_ExtSupply12LPnPolarity 1)
-	 * VextSupply2Regu          = force OFF (OTP_ExtSupply12LPnPolarity 1)
-	 * VextSupply3Regu          = force OFF (OTP_ExtSupply3LPnPolarity 0)
-	 * ExtSupply2Bypass         = ExtSupply12LPn ball is 0 when Ena is 0
-	 * ExtSupply3Bypass         = ExtSupply3LPn ball is 0 when Ena is 0
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_EXTSUPPLYREGU,          0xff, 0x30),
-	/*
-	 * Vaux1Regu                = force HP
-	 * Vaux2Regu                = force off
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VAUX12REGU,             0x0f, 0x01),
-	/*
-	 * Vaux3Regu                = force off
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VRF1VAUX3REGU,          0x03, 0x00),
-	/*
-	 * VsmpsASel1
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSASEL1,    0x00, 0x00),
-	/*
-	 * VsmpsASel2
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSASEL2,    0x00, 0x00),
-	/*
-	 * VsmpsASel3
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSASEL3,    0x00, 0x00),
-	/*
-	 * VsmpsBSel1
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSBSEL1,    0x00, 0x00),
-	/*
-	 * VsmpsBSel2
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSBSEL2,    0x00, 0x00),
-	/*
-	 * VsmpsBSel3
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSMPSBSEL3,    0x00, 0x00),
-	/*
-	 * VsafeSel1
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSAFESEL1,    0x00, 0x00),
-	/*
-	 * VsafeSel2
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSAFESEL2,    0x00, 0x00),
-	/*
-	 * VsafeSel3
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VSAFESEL3,    0x00, 0x00),
-	/*
-	 * Vaux1Sel                 = 2.8 V
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VAUX1SEL,               0x0f, 0x0C),
-	/*
-	 * Vaux2Sel                 = 2.9 V
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VAUX2SEL,               0x0f, 0x0d),
-	/*
-	 * Vaux3Sel                 = 2.91 V
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VRF1VAUX3SEL,           0x07, 0x07),
-	/*
-	 * Vaux4RequestCtrl
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VAUX4REQCTRL,    0x00, 0x00),
-	/*
-	 * Vaux4Regu
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VAUX4REGU,    0x00, 0x00),
-	/*
-	 * Vaux4Sel
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_VAUX4SEL,    0x00, 0x00),
-	/*
-	 * Vaux1Disch               = short discharge time
-	 * Vaux2Disch               = short discharge time
-	 * Vaux3Disch               = short discharge time
-	 * Vintcore12Disch          = short discharge time
-	 * VTVoutDisch              = short discharge time
-	 * VaudioDisch              = short discharge time
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUCTRLDISCH,          0xfc, 0x00),
-	/*
-	 * VanaDisch                = short discharge time
-	 * Vaux8PullDownEna         = pulldown disabled when Vaux8 is disabled
-	 * Vaux8Disch               = short discharge time
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUCTRLDISCH2,         0x16, 0x00),
-	/*
-	 * Vaux4Disch               = short discharge time
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_REGUCTRLDISCH3,         0x01, 0x00),
-	/*
-	 * Vaux5Sel
-	 * Vaux5LP
-	 * Vaux5Ena
-	 * Vaux5Disch
-	 * Vaux5DisSfst
-	 * Vaux5DisPulld
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_CTRLVAUX5,              0x00, 0x00),
-	/*
-	 * Vaux6Sel
-	 * Vaux6LP
-	 * Vaux6Ena
-	 * Vaux6DisPulld
-	 */
-	INIT_REGULATOR_REGISTER(AB8505_CTRLVAUX6,              0x00, 0x00),
-};
-
-static struct regulator_init_data ab8505_regulators[AB8505_NUM_REGULATORS] = {
-	/* supplies to the display/camera */
-	[AB8505_LDO_AUX1] = {
-		.constraints = {
-			.name = "V-DISPLAY",
-			.min_uV = 2800000,
-			.max_uV = 3300000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS,
-			.boot_on = 1, /* display is on at boot */
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux1_consumers),
-		.consumer_supplies = ab8500_vaux1_consumers,
-	},
-	/* supplies to the on-board eMMC */
-	[AB8505_LDO_AUX2] = {
-		.constraints = {
-			.name = "V-eMMC1",
-			.min_uV = 1100000,
-			.max_uV = 3300000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux2_consumers),
-		.consumer_supplies = ab8500_vaux2_consumers,
-	},
-	/* supply for VAUX3, supplies to SDcard slots */
-	[AB8505_LDO_AUX3] = {
-		.constraints = {
-			.name = "V-MMC-SD",
-			.min_uV = 1100000,
-			.max_uV = 3300000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux3_consumers),
-		.consumer_supplies = ab8500_vaux3_consumers,
-	},
-	/* supply for VAUX4, supplies to NFC and standalone secure element */
-	[AB8505_LDO_AUX4] = {
-		.constraints = {
-			.name = "V-NFC-SE",
-			.min_uV = 1100000,
-			.max_uV = 3300000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8505_vaux4_consumers),
-		.consumer_supplies = ab8505_vaux4_consumers,
-	},
-	/* supply for VAUX5, supplies to TBD */
-	[AB8505_LDO_AUX5] = {
-		.constraints = {
-			.name = "V-AUX5",
-			.min_uV = 1050000,
-			.max_uV = 2790000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8505_vaux5_consumers),
-		.consumer_supplies = ab8505_vaux5_consumers,
-	},
-	/* supply for VAUX6, supplies to TBD */
-	[AB8505_LDO_AUX6] = {
-		.constraints = {
-			.name = "V-AUX6",
-			.min_uV = 1050000,
-			.max_uV = 2790000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8505_vaux6_consumers),
-		.consumer_supplies = ab8505_vaux6_consumers,
-	},
-	/* supply for gpadc, ADC LDO */
-	[AB8505_LDO_ADC] = {
-		.constraints = {
-			.name = "V-ADC",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8505_vadc_consumers),
-		.consumer_supplies = ab8505_vadc_consumers,
-	},
-	/* supply for ab8500-vaudio, VAUDIO LDO */
-	[AB8505_LDO_AUDIO] = {
-		.constraints = {
-			.name = "V-AUD",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaud_consumers),
-		.consumer_supplies = ab8500_vaud_consumers,
-	},
-	/* supply for v-anamic1 VAMic1-LDO */
-	[AB8505_LDO_ANAMIC1] = {
-		.constraints = {
-			.name = "V-AMIC1",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vamic1_consumers),
-		.consumer_supplies = ab8500_vamic1_consumers,
-	},
-	/* supply for v-amic2, VAMIC2 LDO, reuse constants for AMIC1 */
-	[AB8505_LDO_ANAMIC2] = {
-		.constraints = {
-			.name = "V-AMIC2",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vamic2_consumers),
-		.consumer_supplies = ab8500_vamic2_consumers,
-	},
-	/* supply for v-aux8, VAUX8 LDO */
-	[AB8505_LDO_AUX8] = {
-		.constraints = {
-			.name = "V-AUX8",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8505_vaux8_consumers),
-		.consumer_supplies = ab8505_vaux8_consumers,
-	},
-	/* supply for v-intcore12, VINTCORE12 LDO */
-	[AB8505_LDO_INTCORE] = {
-		.constraints = {
-			.name = "V-INTCORE",
-			.min_uV = 1250000,
-			.max_uV = 1350000,
-			.input_uV = 1800000,
-			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE |
-					  REGULATOR_CHANGE_DRMS,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vintcore_consumers),
-		.consumer_supplies = ab8500_vintcore_consumers,
-	},
-	/* supply for LDO USB */
-	[AB8505_LDO_USB] = {
-		.constraints = {
-			.name = "V-USB",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_MODE,
-			.valid_modes_mask = REGULATOR_MODE_NORMAL |
-					    REGULATOR_MODE_IDLE,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8505_usb_consumers),
-		.consumer_supplies = ab8505_usb_consumers,
-	},
-	/* supply for U8500 CSI-DSI, VANA LDO */
-	[AB8505_LDO_ANA] = {
-		.constraints = {
-			.name = "V-CSI-DSI",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(ab8500_vana_consumers),
-		.consumer_supplies = ab8500_vana_consumers,
-	},
-};
-
-struct ab8500_regulator_platform_data ab8500_regulator_plat_data = {
-	.reg_init               = ab8500_reg_init,
-	.num_reg_init           = ARRAY_SIZE(ab8500_reg_init),
-	.regulator              = ab8500_regulators,
-	.num_regulator          = ARRAY_SIZE(ab8500_regulators),
-	.ext_regulator          = ab8500_ext_regulators,
-	.num_ext_regulator      = ARRAY_SIZE(ab8500_ext_regulators),
-};
-
-struct ab8500_regulator_platform_data ab8505_regulator_plat_data = {
-	.reg_init               = ab8505_reg_init,
-	.num_reg_init           = ARRAY_SIZE(ab8505_reg_init),
-	.regulator              = ab8505_regulators,
-	.num_regulator          = ARRAY_SIZE(ab8505_regulators),
-};
-
-static void ab8500_modify_reg_init(int id, u8 mask, u8 value)
-{
-	int i;
-
-	if (cpu_is_u8520()) {
-		for (i = ARRAY_SIZE(ab8505_reg_init) - 1; i >= 0; i--) {
-			if (ab8505_reg_init[i].id == id) {
-				u8 initval = ab8505_reg_init[i].value;
-				initval = (initval & ~mask) | (value & mask);
-				ab8505_reg_init[i].value = initval;
-
-				BUG_ON(mask & ~ab8505_reg_init[i].mask);
-				return;
-			}
-		}
-	} else {
-		for (i = ARRAY_SIZE(ab8500_reg_init) - 1; i >= 0; i--) {
-			if (ab8500_reg_init[i].id == id) {
-				u8 initval = ab8500_reg_init[i].value;
-				initval = (initval & ~mask) | (value & mask);
-				ab8500_reg_init[i].value = initval;
-
-				BUG_ON(mask & ~ab8500_reg_init[i].mask);
-				return;
-			}
-		}
-	}
-
-	BUG_ON(1);
-}
-
-void mop500_regulator_init(void)
-{
-	struct regulator_init_data *regulator;
-
-	/*
-	 * Temporarily turn on Vaux2 on 8520 machine
-	 */
-	if (cpu_is_u8520()) {
-		/* Vaux2 initialized to be on */
-		ab8500_modify_reg_init(AB8505_VAUX12REGU, 0x0f, 0x05);
-	}
-
-	/*
-	 * Handle AB8500_EXT_SUPPLY2 on HREFP_V20_V50 boards (do it for
-	 * all HREFP_V20 boards)
-	 */
-	if (cpu_is_u8500v20()) {
-		/* VextSupply2RequestCtrl =  HP/OFF depending on VxRequest */
-		ab8500_modify_reg_init(AB8500_REGUREQUESTCTRL3, 0x01, 0x01);
-
-		/* VextSupply2SysClkReq1HPValid = SysClkReq1 controlled */
-		ab8500_modify_reg_init(AB8500_REGUSYSCLKREQ1HPVALID2,
-			0x20, 0x20);
-
-		/* VextSupply2 = force HP at initialization */
-		ab8500_modify_reg_init(AB8500_EXTSUPPLYREGU, 0x0c, 0x04);
-
-		/* enable VextSupply2 during platform active */
-		regulator = &ab8500_ext_regulators[AB8500_EXT_SUPPLY2];
-		regulator->constraints.always_on = 1;
-
-		/* disable VextSupply2 in suspend */
-		regulator = &ab8500_ext_regulators[AB8500_EXT_SUPPLY2];
-		regulator->constraints.state_mem.disabled = 1;
-		regulator->constraints.state_standby.disabled = 1;
-
-		/* enable VextSupply2 HW control (used in suspend) */
-		regulator->driver_data = (void *)&ab8500_ext_supply2;
-	}
-}
diff --git a/arch/arm/mach-ux500/board-mop500-regulators.h b/arch/arm/mach-ux500/board-mop500-regulators.h
deleted file mode 100644
index 9bece38fe933..000000000000
--- a/arch/arm/mach-ux500/board-mop500-regulators.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License Terms: GNU General Public License v2
- *
- * Author: Bengt Jonsson <bengt.g.jonsson@stericsson.com> for ST-Ericsson
- *
- * MOP500 board specific initialization for regulators
- */
-
-#ifndef __BOARD_MOP500_REGULATORS_H
-#define __BOARD_MOP500_REGULATORS_H
-
-#include <linux/regulator/machine.h>
-#include <linux/regulator/ab8500.h>
-
-extern struct ab8500_regulator_platform_data ab8500_regulator_plat_data;
-extern struct ab8500_regulator_platform_data ab8505_regulator_plat_data;
-extern struct regulator_init_data tps61052_regulator;
-extern struct regulator_init_data gpio_en_3v3_regulator;
-
-void mop500_regulator_init(void);
-
-#endif
diff --git a/arch/arm/mach-ux500/cache-l2x0.c b/arch/arm/mach-ux500/cache-l2x0.c
deleted file mode 100644
index 780bd13cd7e3..000000000000
--- a/arch/arm/mach-ux500/cache-l2x0.c
+++ /dev/null
@@ -1,67 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2011
- *
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-
-#include <asm/outercache.h>
-#include <asm/hardware/cache-l2x0.h>
-
-#include "db8500-regs.h"
-#include "id.h"
-
-static int __init ux500_l2x0_unlock(void)
-{
-	int i;
-	struct device_node *np;
-	void __iomem *l2x0_base;
-
-	np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
-	l2x0_base = of_iomap(np, 0);
-	of_node_put(np);
-	if (!l2x0_base)
-		return -ENODEV;
-
-	/*
-	 * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
-	 * apparently locks both caches before jumping to the kernel. The
-	 * l2x0 core will not touch the unlock registers if the l2x0 is
-	 * already enabled, so we do it right here instead. The PL310 has
-	 * 8 sets of registers, one per possible CPU.
-	 */
-	for (i = 0; i < 8; i++) {
-		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
-			       i * L2X0_LOCKDOWN_STRIDE);
-		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
-			       i * L2X0_LOCKDOWN_STRIDE);
-	}
-	iounmap(l2x0_base);
-	return 0;
-}
-
-static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
-{
-	/*
-	 * We can't write to secure registers as we are in non-secure
-	 * mode, until we have some SMI service available.
-	 */
-}
-
-static int __init ux500_l2x0_init(void)
-{
-	/* Multiplatform guard */
-	if (!((cpu_is_u8500_family() || cpu_is_ux540_family())))
-		return -ENODEV;
-
-	/* Unlock before init */
-	ux500_l2x0_unlock();
-	outer_cache.write_sec = ux500_l2c310_write_sec;
-	l2x0_of_init(0, ~0);
-
-	return 0;
-}
-early_initcall(ux500_l2x0_init);
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index a557955472ea..46b1da1bf5d2 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -12,41 +12,107 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/amba/bus.h>
+#include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/irqchip/arm-gic.h>
+#include <linux/mfd/dbx500-prcmu.h>
+#include <linux/platform_data/arm-ux500-pm.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/mfd/abx500/ab8500.h>
-#include <linux/mfd/dbx500-prcmu.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/perf/arm_pmu.h>
 #include <linux/regulator/machine.h>
-#include <linux/random.h>
 
+#include <asm/outercache.h>
+#include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/map.h>
+#include <asm/mach/arch.h>
 
 #include "setup.h"
 
-#include "board-mop500-regulators.h"
 #include "board-mop500.h"
 #include "db8500-regs.h"
-#include "id.h"
 
-static struct ab8500_platform_data ab8500_platdata = {
-	.regulator	= &ab8500_regulator_plat_data,
-};
+static int __init ux500_l2x0_unlock(void)
+{
+	int i;
+	struct device_node *np;
+	void __iomem *l2x0_base;
 
-static struct prcmu_pdata db8500_prcmu_pdata = {
-	.ab_platdata	= &ab8500_platdata,
-	.version_offset	= DB8500_PRCMU_FW_VERSION_OFFSET,
-	.legacy_offset	= DB8500_PRCMU_LEGACY_OFFSET,
-};
+	np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
+	l2x0_base = of_iomap(np, 0);
+	of_node_put(np);
+	if (!l2x0_base)
+		return -ENODEV;
+
+	/*
+	 * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
+	 * apparently locks both caches before jumping to the kernel. The
+	 * l2x0 core will not touch the unlock registers if the l2x0 is
+	 * already enabled, so we do it right here instead. The PL310 has
+	 * 8 sets of registers, one per possible CPU.
+	 */
+	for (i = 0; i < 8; i++) {
+		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
+			       i * L2X0_LOCKDOWN_STRIDE);
+		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
+			       i * L2X0_LOCKDOWN_STRIDE);
+	}
+	iounmap(l2x0_base);
+	return 0;
+}
+
+static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
+{
+	/*
+	 * We can't write to secure registers as we are in non-secure
+	 * mode, until we have some SMI service available.
+	 */
+}
 
-static void __init u8500_map_io(void)
+/*
+ * FIXME: Should we set up the GPIO domain here?
+ *
+ * The problem is that we cannot put the interrupt resources into the platform
+ * device until the irqdomain has been added. Right now, we set the GIC interrupt
+ * domain from init_irq(), then load the gpio driver from
+ * core_initcall(nmk_gpio_init) and add the platform devices from
+ * arch_initcall(customize_machine).
+ *
+ * This feels fragile because it depends on the gpio device getting probed
+ * _before_ any device uses the gpio interrupts.
+*/
+static void __init ux500_init_irq(void)
+{
+	struct device_node *np;
+	struct resource r;
+
+	irqchip_init();
+	np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
+	of_address_to_resource(np, 0, &r);
+	of_node_put(np);
+	if (!r.start) {
+		pr_err("could not find PRCMU base resource\n");
+		return;
+	}
+	prcmu_early_init(r.start, r.end-r.start);
+	ux500_pm_init(r.start, r.end-r.start);
+
+	/* Unlock before init */
+	ux500_l2x0_unlock();
+	outer_cache.write_sec = ux500_l2c310_write_sec;
+}
+
+static void ux500_restart(enum reboot_mode mode, const char *cmd)
 {
-	debug_ll_io_init();
-	ux500_setup_id();
+	local_irq_disable();
+	local_fiq_disable();
+
+	prcmu_system_reset(0);
 }
 
 /*
@@ -73,31 +139,6 @@ static struct arm_pmu_platdata db8500_pmu_platdata = {
 	.handle_irq		= db8500_pmu_handler,
 };
 
-static const char *db8500_read_soc_id(void)
-{
-	void __iomem *uid;
-	const char *retstr;
-
-	uid = ioremap(U8500_BB_UID_BASE, 0x20);
-	if (!uid)
-		return NULL;
-	/* Throw these device-specific numbers into the entropy pool */
-	add_device_randomness(uid, 0x14);
-	retstr = kasprintf(GFP_KERNEL, "%08x%08x%08x%08x%08x",
-			 readl((u32 *)uid+0),
-			 readl((u32 *)uid+1), readl((u32 *)uid+2),
-			 readl((u32 *)uid+3), readl((u32 *)uid+4));
-	iounmap(uid);
-	return retstr;
-}
-
-static struct device * __init db8500_soc_device_init(void)
-{
-	const char *soc_id = db8500_read_soc_id();
-
-	return ux500_soc_device_init(soc_id);
-}
-
 static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	/* Requires call-back bindings. */
 	OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
@@ -111,8 +152,7 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000,
 		       "ux500-msp-i2s.3", &msp3_platform_data),
 	/* Requires non-DT:able platform data. */
-	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
-			&db8500_prcmu_pdata),
+	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu", NULL),
 	OF_DEV_AUXDATA("stericsson,ux500-cryp", 0xa03cb000, "cryp1", NULL),
 	OF_DEV_AUXDATA("stericsson,ux500-hash", 0xa03c2000, "hash1", NULL),
 	OF_DEV_AUXDATA("stericsson,snd-soc-mop500", 0, "snd-soc-mop500.0",
@@ -121,8 +161,7 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 };
 
 static struct of_dev_auxdata u8540_auxdata_lookup[] __initdata = {
-	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
-			&db8500_prcmu_pdata),
+	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu", NULL),
 	{},
 };
 
@@ -136,15 +175,13 @@ static const struct of_device_id u8500_local_bus_nodes[] = {
 
 static void __init u8500_init_machine(void)
 {
-	struct device *parent = db8500_soc_device_init();
-
 	/* automatically probe child nodes of dbx5x0 devices */
 	if (of_machine_is_compatible("st-ericsson,u8540"))
 		of_platform_populate(NULL, u8500_local_bus_nodes,
-				     u8540_auxdata_lookup, parent);
+				     u8540_auxdata_lookup, NULL);
 	else
 		of_platform_populate(NULL, u8500_local_bus_nodes,
-				     u8500_auxdata_lookup, parent);
+				     u8500_auxdata_lookup, NULL);
 }
 
 static const char * stericsson_dt_platform_compat[] = {
@@ -156,10 +193,10 @@ static const char * stericsson_dt_platform_compat[] = {
 };
 
 DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)")
-	.map_io		= u8500_map_io,
+	.l2c_aux_val    = 0,
+	.l2c_aux_mask	= ~0,
 	.init_irq	= ux500_init_irq,
 	.init_machine	= u8500_init_machine,
-	.init_late	= NULL,
 	.dt_compat      = stericsson_dt_platform_compat,
 	.restart        = ux500_restart,
 MACHINE_END
diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c
deleted file mode 100644
index 82156cbc22ce..000000000000
--- a/arch/arm/mach-ux500/cpu.c
+++ /dev/null
@@ -1,148 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * Author: Lee Jones <lee.jones@linaro.org> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/mfd/dbx500-prcmu.h>
-#include <linux/sys_soc.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-#include <linux/stat.h>
-#include <linux/of.h>
-#include <linux/of_irq.h>
-#include <linux/of_address.h>
-#include <linux/irq.h>
-#include <linux/irqchip.h>
-#include <linux/irqchip/arm-gic.h>
-#include <linux/platform_data/clk-ux500.h>
-#include <linux/platform_data/arm-ux500-pm.h>
-
-#include <asm/mach/map.h>
-
-#include "setup.h"
-
-#include "board-mop500.h"
-#include "db8500-regs.h"
-#include "id.h"
-
-void ux500_restart(enum reboot_mode mode, const char *cmd)
-{
-	local_irq_disable();
-	local_fiq_disable();
-
-	prcmu_system_reset(0);
-}
-
-/*
- * FIXME: Should we set up the GPIO domain here?
- *
- * The problem is that we cannot put the interrupt resources into the platform
- * device until the irqdomain has been added. Right now, we set the GIC interrupt
- * domain from init_irq(), then load the gpio driver from
- * core_initcall(nmk_gpio_init) and add the platform devices from
- * arch_initcall(customize_machine).
- *
- * This feels fragile because it depends on the gpio device getting probed
- * _before_ any device uses the gpio interrupts.
-*/
-void __init ux500_init_irq(void)
-{
-	struct device_node *np;
-	struct resource r;
-
-	irqchip_init();
-	np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
-	of_address_to_resource(np, 0, &r);
-	of_node_put(np);
-	if (!r.start) {
-		pr_err("could not find PRCMU base resource\n");
-		return;
-	}
-	prcmu_early_init(r.start, r.end-r.start);
-	ux500_pm_init(r.start, r.end-r.start);
-
-	/*
-	 * Init clocks here so that they are available for system timer
-	 * initialization.
-	 */
-	if (cpu_is_u8500_family())
-		u8500_clk_init();
-	else if (cpu_is_u9540())
-		u9540_clk_init();
-	else if (cpu_is_u8540())
-		u8540_clk_init();
-}
-
-static const char * __init ux500_get_machine(void)
-{
-	return kasprintf(GFP_KERNEL, "DB%4x", dbx500_partnumber());
-}
-
-static const char * __init ux500_get_family(void)
-{
-	return kasprintf(GFP_KERNEL, "ux500");
-}
-
-static const char * __init ux500_get_revision(void)
-{
-	unsigned int rev = dbx500_revision();
-
-	if (rev == 0x01)
-		return kasprintf(GFP_KERNEL, "%s", "ED");
-	else if (rev >= 0xA0)
-		return kasprintf(GFP_KERNEL, "%d.%d",
-				 (rev >> 4) - 0xA + 1, rev & 0xf);
-
-	return kasprintf(GFP_KERNEL, "%s", "Unknown");
-}
-
-static ssize_t ux500_get_process(struct device *dev,
-					struct device_attribute *attr,
-					char *buf)
-{
-	if (dbx500_id.process == 0x00)
-		return sprintf(buf, "Standard\n");
-
-	return sprintf(buf, "%02xnm\n", dbx500_id.process);
-}
-
-static void __init soc_info_populate(struct soc_device_attribute *soc_dev_attr,
-				     const char *soc_id)
-{
-	soc_dev_attr->soc_id   = soc_id;
-	soc_dev_attr->machine  = ux500_get_machine();
-	soc_dev_attr->family   = ux500_get_family();
-	soc_dev_attr->revision = ux500_get_revision();
-}
-
-static const struct device_attribute ux500_soc_attr =
-	__ATTR(process,  S_IRUGO, ux500_get_process,  NULL);
-
-struct device * __init ux500_soc_device_init(const char *soc_id)
-{
-	struct device *parent;
-	struct soc_device *soc_dev;
-	struct soc_device_attribute *soc_dev_attr;
-
-	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
-	if (!soc_dev_attr)
-		return ERR_PTR(-ENOMEM);
-
-	soc_info_populate(soc_dev_attr, soc_id);
-
-	soc_dev = soc_device_register(soc_dev_attr);
-	if (IS_ERR(soc_dev)) {
-	        kfree(soc_dev_attr);
-		return NULL;
-	}
-
-	parent = soc_device_to_device(soc_dev);
-	device_create_file(parent, &ux500_soc_attr);
-
-	return parent;
-}
diff --git a/arch/arm/mach-ux500/id.c b/arch/arm/mach-ux500/id.c
deleted file mode 100644
index 1e81e990044b..000000000000
--- a/arch/arm/mach-ux500/id.c
+++ /dev/null
@@ -1,116 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/io.h>
-
-#include <asm/cputype.h>
-#include <asm/tlbflush.h>
-#include <asm/cacheflush.h>
-#include <asm/mach/map.h>
-
-#include "setup.h"
-
-#include "db8500-regs.h"
-#include "id.h"
-
-struct dbx500_asic_id dbx500_id;
-
-static unsigned int __init ux500_read_asicid(phys_addr_t addr)
-{
-	phys_addr_t base = addr & ~0xfff;
-	struct map_desc desc = {
-		.virtual	= (unsigned long)UX500_VIRT_ROM,
-		.pfn		= __phys_to_pfn(base),
-		.length		= SZ_16K,
-		.type		= MT_DEVICE,
-	};
-
-	iotable_init(&desc, 1);
-
-	/* As in devicemaps_init() */
-	local_flush_tlb_all();
-	flush_cache_all();
-
-	return readl(UX500_VIRT_ROM + (addr & 0xfff));
-}
-
-static void ux500_print_soc_info(unsigned int asicid)
-{
-	unsigned int rev = dbx500_revision();
-
-	pr_info("DB%4x ", dbx500_partnumber());
-
-	if (rev == 0x01)
-		pr_cont("Early Drop");
-	else if (rev >= 0xA0)
-		pr_cont("v%d.%d" , (rev >> 4) - 0xA + 1, rev & 0xf);
-	else
-		pr_cont("Unknown");
-
-	pr_cont(" [%#010x]\n", asicid);
-}
-
-static unsigned int partnumber(unsigned int asicid)
-{
-	return (asicid >> 8) & 0xffff;
-}
-
-/*
- * SOC		MIDR		ASICID ADDRESS		ASICID VALUE
- * DB8500ed	0x410fc090	0x9001FFF4		0x00850001
- * DB8500v1	0x411fc091	0x9001FFF4		0x008500A0
- * DB8500v1.1	0x411fc091	0x9001FFF4		0x008500A1
- * DB8500v2	0x412fc091	0x9001DBF4		0x008500B0
- * DB8520v2.2	0x412fc091	0x9001DBF4		0x008500B2
- * DB5500v1	0x412fc091	0x9001FFF4		0x005500A0
- * DB9540	0x413fc090	0xFFFFDBF4		0x009540xx
- */
-
-void __init ux500_setup_id(void)
-{
-	unsigned int cpuid = read_cpuid_id();
-	unsigned int asicid = 0;
-	phys_addr_t addr = 0;
-
-	switch (cpuid) {
-	case 0x410fc090: /* DB8500ed */
-	case 0x411fc091: /* DB8500v1 */
-		addr = 0x9001FFF4;
-		break;
-
-	case 0x412fc091: /* DB8520 / DB8500v2 / DB5500v1 */
-		asicid = ux500_read_asicid(0x9001DBF4);
-		if (partnumber(asicid) == 0x8500 ||
-		    partnumber(asicid) == 0x8520)
-			/* DB8500v2 */
-			break;
-
-		/* DB5500v1 */
-		addr = 0x9001FFF4;
-		break;
-
-	case 0x413fc090: /* DB9540 */
-		addr = 0xFFFFDBF4;
-		break;
-	}
-
-	if (addr)
-		asicid = ux500_read_asicid(addr);
-
-	if (!asicid) {
-		pr_err("Unable to identify SoC\n");
-		ux500_unknown_soc();
-	}
-
-	dbx500_id.process = asicid >> 24;
-	dbx500_id.partnumber = partnumber(asicid);
-	dbx500_id.revision = asicid & 0xff;
-
-	ux500_print_soc_info(asicid);
-}
diff --git a/arch/arm/mach-ux500/id.h b/arch/arm/mach-ux500/id.h
deleted file mode 100644
index bcc58a8cccbc..000000000000
--- a/arch/arm/mach-ux500/id.h
+++ /dev/null
@@ -1,144 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#ifndef __MACH_UX500_ID
-#define __MACH_UX500_ID
-
-/**
- * struct dbx500_asic_id - fields of the ASIC ID
- * @process: the manufacturing process, 0x40 is 40 nm 0x00 is "standard"
- * @partnumber: hithereto 0x8500 for DB8500
- * @revision: version code in the series
- */
-struct dbx500_asic_id {
-	u16	partnumber;
-	u8	revision;
-	u8	process;
-};
-
-extern struct dbx500_asic_id dbx500_id;
-
-static inline unsigned int __attribute_const__ dbx500_partnumber(void)
-{
-	return dbx500_id.partnumber;
-}
-
-static inline unsigned int __attribute_const__ dbx500_revision(void)
-{
-	return dbx500_id.revision;
-}
-
-/*
- * SOCs
- */
-
-static inline bool __attribute_const__ cpu_is_u8500(void)
-{
-	return dbx500_partnumber() == 0x8500;
-}
-
-static inline bool __attribute_const__ cpu_is_u8520(void)
-{
-	return dbx500_partnumber() == 0x8520;
-}
-
-static inline bool cpu_is_u8500_family(void)
-{
-	return cpu_is_u8500() || cpu_is_u8520();
-}
-
-static inline bool __attribute_const__ cpu_is_u9540(void)
-{
-	return dbx500_partnumber() == 0x9540;
-}
-
-static inline bool __attribute_const__ cpu_is_u8540(void)
-{
-	return dbx500_partnumber() == 0x8540;
-}
-
-static inline bool __attribute_const__ cpu_is_u8580(void)
-{
-	return dbx500_partnumber() == 0x8580;
-}
-
-static inline bool cpu_is_ux540_family(void)
-{
-	return cpu_is_u9540() || cpu_is_u8540() || cpu_is_u8580();
-}
-
-/*
- * 8500 revisions
- */
-
-static inline bool __attribute_const__ cpu_is_u8500ed(void)
-{
-	return cpu_is_u8500() && dbx500_revision() == 0x00;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v1(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() & 0xf0) == 0xA0;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v10(void)
-{
-	return cpu_is_u8500() && dbx500_revision() == 0xA0;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v11(void)
-{
-	return cpu_is_u8500() && dbx500_revision() == 0xA1;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v2(void)
-{
-	return cpu_is_u8500() && ((dbx500_revision() & 0xf0) == 0xB0);
-}
-
-static inline bool cpu_is_u8500v20(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() == 0xB0);
-}
-
-static inline bool cpu_is_u8500v21(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() == 0xB1);
-}
-
-static inline bool cpu_is_u8500v22(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() == 0xB2);
-}
-
-static inline bool cpu_is_u8500v20_or_later(void)
-{
-	return (cpu_is_u8500() && !cpu_is_u8500v10() && !cpu_is_u8500v11());
-}
-
-/*
- * 8540 revisions
- */
-
-static inline bool __attribute_const__ cpu_is_u8540v10(void)
-{
-	return cpu_is_u8540() && dbx500_revision() == 0xA0;
-}
-
-static inline bool __attribute_const__ cpu_is_u8580v10(void)
-{
-	return cpu_is_u8580() && dbx500_revision() == 0xA0;
-}
-
-static inline bool ux500_is_svp(void)
-{
-	return false;
-}
-
-#define ux500_unknown_soc()	BUG()
-
-#endif
diff --git a/arch/arm/mach-ux500/platsmp.c b/arch/arm/mach-ux500/platsmp.c
index 88b8ab4f300c..8f2f615ff958 100644
--- a/arch/arm/mach-ux500/platsmp.c
+++ b/arch/arm/mach-ux500/platsmp.c
@@ -26,7 +26,6 @@
 #include "setup.h"
 
 #include "db8500-regs.h"
-#include "id.h"
 
 /* Magic triggers in backup RAM */
 #define UX500_CPU1_JUMPADDR_OFFSET 0x1FF4
diff --git a/arch/arm/mach-ux500/setup.h b/arch/arm/mach-ux500/setup.h
index c704254ab67c..988e7c77068d 100644
--- a/arch/arm/mach-ux500/setup.h
+++ b/arch/arm/mach-ux500/setup.h
@@ -11,18 +11,6 @@
 #ifndef __ASM_ARCH_SETUP_H
 #define __ASM_ARCH_SETUP_H
 
-#include <asm/mach/arch.h>
-#include <linux/init.h>
-#include <linux/mfd/abx500/ab8500.h>
-
-void ux500_restart(enum reboot_mode mode, const char *cmd);
-
-void __init ux500_setup_id(void);
-
-extern void __init ux500_init_irq(void);
-
-extern struct device *ux500_soc_device_init(const char *soc_id);
-
 extern void ux500_cpu_die(unsigned int cpu);
 
 #endif /*  __ASM_ARCH_SETUP_H */