| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If irq flags are not cleared for certain operations we
print an error message.
Since this should never occur in normal operation, this
patch is an optional safety-net and debugging tool.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/2de305d3046c7281a7123347899abbaa64c54fb8.1590255176.git.hns@goldelico.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since
commit 27d13da8782a ("w1: omap-hdq: Simplify driver with PM runtime autosuspend")
was applied,
I did see timeouts and wrong values when reading a bq27000 connected
to hdq of the omap3. This occurred mainly after boot but remained and
only sometimes settled down after several reads.
root@letux:~# time cat /sys/class/power_supply/bq27000-battery/uevent
POWER_SUPPLY_NAME=bq27000-battery
POWER_SUPPLY_STATUS=Discharging
POWER_SUPPLY_PRESENT=1
POWER_SUPPLY_VOLTAGE_NOW=0
POWER_SUPPLY_CURRENT_NOW=0
POWER_SUPPLY_CAPACITY=0
POWER_SUPPLY_CAPACITY_LEVEL=Normal
POWER_SUPPLY_TEMP=-2731
POWER_SUPPLY_TIME_TO_EMPTY_NOW=0
POWER_SUPPLY_TIME_TO_EMPTY_AVG=0
POWER_SUPPLY_TIME_TO_FULL_NOW=0
POWER_SUPPLY_TECHNOLOGY=Li-ion
POWER_SUPPLY_CHARGE_FULL=0
POWER_SUPPLY_CHARGE_NOW=0
POWER_SUPPLY_CHARGE_FULL_DESIGN=0
POWER_SUPPLY_CYCLE_COUNT=0
POWER_SUPPLY_ENERGY_NOW=0
POWER_SUPPLY_POWER_AVG=0
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_MANUFACTURER=Texas Instruments
real 0m15.761s
user 0m0.001s
sys 0m0.025s
root@letux:~#
Sometimes the effect did disappear after accessing
the device multiple times, speed went up and results
became correct.
All this indicates that some interrupts from the hdq
controller are lost by the driver.
Enabling debugging revealed that there were spurious tx
and rx timeouts, i.e. the driver does not always recognise
interrupts. The main problem is that rx and tx interrupts
share a single variable which was sometimes reset to
0 wiping out other interrupts. And it was overwritten
by a second interrupt, independent of whether the
previous interrupt was already processed or not.
This patch improves interrupt handling to avoid such
races and loss of interrupt flags.
The ideas are:
* only the hdq_isr() sets bits in hdq_status
* it does not reset any bits
* it does wake_up() if any interrupt is pending
* bits are only reset by the read/write/break functions
if they were waited for
* this makes sure that no interrupts can be lost
* rx/tx/timeout bits are completely decoupled from each
other (and not reset all after waiting for any of them)
* which bits to reset is now specified by a new parameter
to hdq_reset_irqstatus()
* hdq_reset_irqstatus() also returns the state before
resetting so that we can encapsulate the spinlock
* this should now handle the case that the write and read
are both already finished quickly before the hdq_write_byte()
ends.
* Or that two interrupts occur in succession before
they are processed by the driver.
Old code may have reset all status bits making the next
hdq_read_byte() timeout.
* the spinlock now always protects changing of bits in function
hdq_reset_irqstatus() which could become a read-write-modify
problem if the interrupt handler tries to read-modify-write
exactly at the same moment
* we add mutex protection also for hdq_write_byte() just to
be safe to not to disturb a hdq_read_byte() triggered by
some other thread/process.
This patch was tested on a GTA04 and results in no
boot problems any more. And first read after boot is now ok:
root@letux:~# time cat /sys/class/power_supply/bq27000-battery/uevent
POWER_SUPPLY_NAME=bq27000-battery
POWER_SUPPLY_STATUS=Discharging
POWER_SUPPLY_PRESENT=1
POWER_SUPPLY_VOLTAGE_NOW=3970000
POWER_SUPPLY_CURRENT_NOW=354144
POWER_SUPPLY_CAPACITY=82
POWER_SUPPLY_CAPACITY_LEVEL=Normal
POWER_SUPPLY_TEMP=266
POWER_SUPPLY_TIME_TO_EMPTY_NOW=7680
POWER_SUPPLY_TIME_TO_EMPTY_AVG=7380
POWER_SUPPLY_TECHNOLOGY=Li-ion
POWER_SUPPLY_CHARGE_FULL=934856
POWER_SUPPLY_CHARGE_NOW=763976
POWER_SUPPLY_CHARGE_FULL_DESIGN=1233792
POWER_SUPPLY_CYCLE_COUNT=82
POWER_SUPPLY_ENERGY_NOW=2852840
POWER_SUPPLY_POWER_AVG=1392840
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_MANUFACTURER=Texas Instruments
real 0m0.233s
user 0m0.000s
sys 0m0.025s
root@letux:~#
It was also tested with dev_dbg enabled and more
printk that all activities behave correctly, especially
hdq_write_byte(), hdq_read_byte(), omap_hdq_break().
Not tested is omap_w1_triplet().
Fixes: 27d13da8782a ("w1: omap-hdq: Simplify driver with PM runtime autosuspend")
Cc: stable@vger.kernel.org # v5.6+
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/68fc8623ae741878beef049273696d2377526165.1590255176.git.hns@goldelico.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
omap_w1_read_byte() should return -1 (or 0xff) in case of
error (e.g. missing battery).
The code accidentially overwrites the variable ret and not val,
which is returned. So it will return the initial value 0 instead
of -1.
Fixes: 27d13da8782a ("w1: omap-hdq: Simplify driver with PM runtime autosuspend")
Cc: stable@vger.kernel.org # v5.6+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/b2c2192b461fbb9b8e9bea4ad514a49557a7210b.1590255176.git.hns@goldelico.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Otherwise it will corrupt the console log during debugging.
Fixes: 7b5362a603a1 ("w1: omap_hdq: Fix some error/debug handling.")
Cc: stable@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/cd0d55749a091214106575f6e1d363c6db56622f.1590255176.git.hns@goldelico.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We've had generic code handling module sysconfig and OCP reset registers
for omap variants for many years now and all the drivers really needs to
do is just call runtime PM functions.
Looks like the omap-hdq driver got only partially updated over the years
to use runtime PM, and still has lots of custom PM code left.
We can replace all the custom code for sysconfig, OCP reset, and PM with
just a few lines of runtime PM autosuspend code.
In order to set the device mode properly when pm_runtime_get_sync() is
called during probe, we need to also move parsing of "ti,mode" to happen
earlier before we call pm_runtime_enable().
Since we now disable interrupts lazily in omap_hdq_runtime_suspend(), we
must remove the call to hdq_disable_interrupt() in omap_w1_read_byte().
And we must clear irqstatus calling wait_event_timeout() on it, so let's
add hdq_reset_irqstatus() for that.
Note that the earlier driver specific usage count limit of four seems
completely artificial and should not be an issue in normal use.
Cc: Adam Ford <aford173@gmail.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Kemnade <andreas@kemnade.info> # gta04
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191217004048.46298-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190802135010.24052-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bus master was not removed after unloading the module
or unbinding the driver. That lead to oopses like this
[ 127.842987] Unable to handle kernel paging request at virtual address bf01d04c
[ 127.850646] pgd = 70e3cd9a
[ 127.853698] [bf01d04c] *pgd=8f908811, *pte=00000000, *ppte=00000000
[ 127.860412] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[ 127.866668] Modules linked in: bq27xxx_battery overlay [last unloaded: omap_hdq]
[ 127.874542] CPU: 0 PID: 1022 Comm: w1_bus_master1 Not tainted 4.19.0-rc4-00001-g2d51da718324 #12
[ 127.883819] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[ 127.890441] PC is at 0xbf01d04c
[ 127.893798] LR is at w1_search_process_cb+0x4c/0xfc
[ 127.898956] pc : [<bf01d04c>] lr : [<c05f9580>] psr: a0070013
[ 127.905609] sp : cf885f48 ip : bf01d04c fp : ddf1e11c
[ 127.911132] r10: cf8fe040 r9 : c05f8d00 r8 : cf8fe040
[ 127.916656] r7 : 000000f0 r6 : cf8fe02c r5 : cf8fe000 r4 : cf8fe01c
[ 127.923553] r3 : c05f8d00 r2 : 000000f0 r1 : cf8fe000 r0 : dde1ef10
[ 127.930450] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 127.938018] Control: 10c5387d Table: 8f8f0019 DAC: 00000051
[ 127.944091] Process w1_bus_master1 (pid: 1022, stack limit = 0x9135699f)
[ 127.951171] Stack: (0xcf885f48 to 0xcf886000)
[ 127.955810] 5f40: cf8fe000 00000000 cf884000 cf8fe090 000003e8 c05f8d00
[ 127.964477] 5f60: dde5fc34 c05f9700 ddf1e100 ddf1e540 cf884000 cf8fe000 c05f9694 00000000
[ 127.973114] 5f80: dde5fc34 c01499a4 00000000 ddf1e540 c0149874 00000000 00000000 00000000
[ 127.981781] 5fa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
[ 127.990447] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 127.999114] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 128.007781] [<c05f9580>] (w1_search_process_cb) from [<c05f9700>] (w1_process+0x6c/0x118)
[ 128.016479] [<c05f9700>] (w1_process) from [<c01499a4>] (kthread+0x130/0x148)
[ 128.024047] [<c01499a4>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[ 128.031677] Exception stack(0xcf885fb0 to 0xcf885ff8)
[ 128.037017] 5fa0: 00000000 00000000 00000000 00000000
[ 128.045684] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 128.054351] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 128.061340] Code: bad PC value
[ 128.064697] ---[ end trace af066e33c0e14119 ]---
Cc: <stable@vger.kernel.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() returns an error code, but the omap_hdq
driver ignores it and always returns -ENXIO. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error.
Print error message and propagate the return value of
platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Like other subsystems we should be able to define slave devices outside
of the w1 directory. To do this we move public facing interface
definitions to include/linux/w1.h and rename the internal definition
file to w1_internal.h.
As w1_family.h and w1_int.h contained almost entirely public
driver interface definitions we simply removed these files and
moved the remaining definitions into w1_internal.h.
With this we can now start to move slave devices out of w1/slaves and
into the subsystem based on the function they implement, again like
other drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Structures and functions should be ordered such that forward declaration
use is minimized.
MODULE_* macros should immediately follow the structures and functions
upon which they act.
Remaining MODULE_* macros should be at the end of the file in
alphabetical order.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of error returned by '_omap_hdq_reset()', free resources as done
elsewhere in this function.
This patch slighly changes the semantic of the code. It now propagates the
error code returned by '_omap_hdq_reset()' instead of returning -EINVAL
unconditionally.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e93762bbf681 ("w1: masters: omap_hdq: add support for 1-wire
mode") added a statement to clear the hdq_irqstatus flags in
hdq_read_byte().
If the hdq reading process is scheduled slowly or interrupts are
disabled for a while the hardware read activity might already be
finished on entry of hdq_read_byte(). And hdq_isr() already has set the
hdq_irqstatus to 0x6 (can be seen in debug mode) denoting that both, the
TXCOMPLETE and RXCOMPLETE interrupts occurred in parallel.
This means there is no need to wait and the hdq_read_byte() can just
read the byte from the hdq controller.
By resetting hdq_irqstatus to 0 the read process is forced to be always
waiting again (because the if statement always succeeds) but the
hardware will not issue another RXCOMPLETE interrupt. This results in a
false timeout.
After such a situation the hdq bus hangs.
Link: http://lkml.kernel.org/r/b724765f87ad276a69625bc19806c8c8844c4590.1469513669.git.hns@goldelico.com
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
hdq_usecount was set to zero after a successful read, so
omap_hdq_put could not properly free resources which leads
e.g. to increasing usecounts in lsmod output
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver has no 'compatible' string and so is not found when
using device-tree.
Add one with value to match
hdqw1w: 1w@480b2000 {
device in omap3.dtsi.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Let the driver compile everywhere while
also removing unnecessary headers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
trivial patch, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
this lets us remove a bit of boilerplate code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
trivial patch, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
we have the helpful resource_size() macro to
calculate the size of the memory resource for
us, let's use it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
trivial patch, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
|
|
Convert the OMAP HDQ driver to use runtime PM. Compile- and boot-tested,
but not tested in actual use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Tested-by: NeilBrown <neilb@suse.de>
|
|
HDQ/1-wire registers are 32 bits long, even if the register contents
fit into 8 bits, so accesses must be 32-bit aligned. Evidently the
OMAP2/3 interconnects allowed the driver to get away with 8 bit accesses,
but the OMAP4 puts a stop to that:
[ 1.488800] Driver for 1-wire Dallas network protocol.
[ 1.495025] Bad mode in data abort handler detected
[ 1.500122] Internal error: Oops - bad mode: 0 [#1] SMP
[ 1.505615] Modules linked in:
[ 1.508819] CPU: 0 Not tainted (3.3.0-rc1-00008-g45030e9 #992)
[ 1.515289] PC is at 0xffff0018
[ 1.518615] LR is at omap_hdq_probe+0xd4/0x2cc
The OMAP4430 ES2 Rev X TRM does warn about this restriction in section
23.2.6.2 "HDQ/1-Wire Registers".
Fixes the crash on OMAP4430 ES2 Pandaboard. Tested also on OMAP34xx and
OMAP2420; it seems to work fine on those chips, although due to the lack
of boards with HDQ/1-wire devices here, a more indepth test was not
possible.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
|
|
There is no gain in having a loop - there is no risk of missing the
interrupt with wait_event_timeout.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
- some debug messages missed spaces
- sometimes no error was returned when it should have been
- sometimes a message is printed when there is no error, rather
than when there is one.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
This code makes two calls to clk_get, then test both return values and
fails if either failed.
The problem is that in the first inner if, where the first call to
clk_get has failed, it don't know if the second call has failed as well.
So it don't know whether clk_get should be called on the result of the
second call. Of course, it would be possible to test that value again.
A simpler solution is just to test the result of calling clk_get
directly after each call.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
position p1,p2;
expression e;
statement S;
@@
e = clk_get@p1(...)
...
if@p2 (IS_ERR(e)) S
@@
expression e;
statement S;
identifier l;
position r.p1, p2 != r.p2;
@@
*e = clk_get@p1(...)
... when != clk_put(e)
*if@p2 (...)
{
... when != clk_put(e)
* return ...;
}// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes the following error:
drivers/w1/masters/omap_hdq.c: In function 'hdq_wait_for_flag':
drivers/w1/masters/omap_hdq.c:137: error: implicit declaration of function 'schedule_timeout_uninterruptible'
drivers/w1/masters/omap_hdq.c: In function 'hdq_write_byte':
drivers/w1/masters/omap_hdq.c:177: error: 'TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
drivers/w1/masters/omap_hdq.c:177: error: (Each undeclared identifier is reported only once
drivers/w1/masters/omap_hdq.c:177: error: for each function it appears in.)
drivers/w1/masters/omap_hdq.c:177: error: implicit declaration of function 'schedule_timeout'
drivers/w1/masters/omap_hdq.c: In function 'hdq_isr':
drivers/w1/masters/omap_hdq.c:221: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/w1/masters/omap_hdq.c: In function 'omap_hdq_break':
drivers/w1/masters/omap_hdq.c:316: error: 'TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
A pointer to omap_hdq_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This was found using a semantic patch, more info can be found at:
http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
OMAP LDP boot crash. This is because w1 subsystem changed the search
interface, so update omap_hdq's search interface to follow the change.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols. These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).
This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
