| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Add tables to support MT7622 NAND flash controller.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
MT7622 uses an MTK's earlier NAND flash controller IP which support
different sector size, max spare size per sector and paraity bits...,
some register's offset and definition also been changed in the NAND
flash controller, this patch is the preparation to support MT7622
NAND flash controller.
MT7622 NFC and ECC engine are similar to MT2701's, except below
differences:
(1)MT7622 NFC's max sector size(ECC data size) is 512 bytes, and
MT2701's is 1024, and MT7622's max sector number is 8.
(2)The parity bit of MT7622 is 13, MT2701 is 14.
(3)MT7622 ECC supports less ECC strength, max to 16 bit ecc strength.
(4)MT7622 supports less spare size per sector, max spare size per
sector is 28 bytes.
(5)Some register's offset are different, include ECC_ENCIRQ_EN,
ECC_ENCIRQ_STA, ECC_DECDONE, ECC_DECIRQ_EN and ECC_DECIRQ_STA.
(6)ENC_MODE of ECC_ENCCNFG register is moved from bit 5-6 to bit 4-5.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core currently send the READ0 and SEQIN+PAGEPROG commands in
nand_do_read/write_ops(). This is inconsistent with
->read/write_oob[_raw]() hooks behavior which are expected to send
these commands.
There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core
that a specific controller wants to send the READ/SEQIN+PAGEPROG
commands on its own, but it's an opt-in flag, and existing drivers are
unlikely to be updated to pass it.
Moreover, some controllers cannot dissociate the READ/PAGEPROG commands
from the associated data transfer and ECC engine activation, and
developers have to hack things in their ->cmdfunc() implementation to
handle such complex cases, or have to accept the perf penalty of sending
twice the same command.
To address this problem we are planning on adding a new interface which
is passed all information about a NAND operation (including the amount
of data to transfer) and replacing all calls to ->cmdfunc() to calls to
this new ->exec_op() hook. But, in order to do that, we need to have all
->cmdfunc() calls placed near their associated ->read/write_buf/byte()
calls.
Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS
the default case, and remove this flag.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: tested, fixed and rebased on nand/next]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.
Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Previously, we only select chips and then send reset command to a NAND
device during resuming nand driver. There is a lack of deselecting chips.
It is advised to reset and initialize a NAND device using nand_reset().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
|
|
Currently, we use the fixed ACC timing 0x10804211. This is not the best
setting for each case. Actually, MTK NAND controller can adapt ACC timings
dynamically according to nfi clock frequence.
Implement the ->setup_data_interface() hook to optimize driver performance.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
chip->select_chip will do nfc runtime configuration. There is no need to
do mtk_nfc_hw_init before it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
MT2712 NAND FLASH Controller is similar to MT2701 except those following:
(1) MT2712 supports up to 148B spare size per 1KB size sector (the same
with 74B spare size per 512B size sector). There are three new spare
format: 61, 67, 74.
(2) MT2712 supports up to 80 bit ecc strength. There are three new ecc
strength level: 68, 72, 80.
(3) MT2712 ECC encode parity data register's start offset is 0x300, and
different with 0x10 of MT2701.
(4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE,
MT2701 will generate ecc irq number the same with ecc steps during
page read. However, MT2712 can only generate one ecc irq.
Changes of this patch are:
(1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct
mtk_ecc_caps.
(2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG.
(3) add ecc strength array of mt2712.
(4) add spare size array of mt2712.
(5) add mt2712 nfc and ecc device compatiable and data.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
ECC strength and spare size supported may be different among MTK NAND
FLASH Controller IPs.
This patch contains changes as following:
(1) add new struct mtk_nfc_caps to support different spare size.
(2) add new struct mtk_ecc_caps to support different ecc strength.
(3) remove ECC_CNFG_xBIT define, use a for loop to do ecc strength config.
(4) remove PAGEFMT_SPARE_ define, use a for loop to do spare format config.
(5) malloc ecc->eccdata buffer according to max ecc strength of this IP.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The register NFI_PAGEFMT is always 32 bits length, so it is better to
do register program using writel() compare with writew().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENODEV.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When mtk_nfc_do_write_page() comparing the sector number,because the
sector number field is at the 12th-bit position of NFI_BYTELEN
register,the masked register should be shifted 12 bits before being
compared.The result of this bug may cause the second subpage has
incomplete ECC parity bytes.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Fixes: 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Add support for mediatek's SDG1 NFC nand controller embedded in SoC
2701
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Xiaolei Li <xiaolei.li@mediatek.com>
|
