diff options
Diffstat (limited to 'drivers/net/ethernet/intel/igb')
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_82575.c | 120 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_defines.h | 30 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_hw.h | 2 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_phy.c | 124 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_phy.h | 20 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/igb_ethtool.c | 34 |
6 files changed, 291 insertions, 39 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c index ff6a17cb1362..f21a91a299a2 100644 --- a/drivers/net/ethernet/intel/igb/e1000_82575.c +++ b/drivers/net/ethernet/intel/igb/e1000_82575.c @@ -401,12 +401,82 @@ static s32 igb_init_mac_params_82575(struct e1000_hw *hw) return 0; } +/** + * igb_set_sfp_media_type_82575 - derives SFP module media type. + * @hw: pointer to the HW structure + * + * The media type is chosen based on SFP module. + * compatibility flags retrieved from SFP ID EEPROM. + **/ +static s32 igb_set_sfp_media_type_82575(struct e1000_hw *hw) +{ + s32 ret_val = E1000_ERR_CONFIG; + u32 ctrl_ext = 0; + struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; + struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags; + u8 tranceiver_type = 0; + s32 timeout = 3; + + /* Turn I2C interface ON and power on sfp cage */ + ctrl_ext = rd32(E1000_CTRL_EXT); + ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA; + wr32(E1000_CTRL_EXT, ctrl_ext | E1000_CTRL_I2C_ENA); + + wrfl(); + + /* Read SFP module data */ + while (timeout) { + ret_val = igb_read_sfp_data_byte(hw, + E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_IDENTIFIER_OFFSET), + &tranceiver_type); + if (ret_val == 0) + break; + msleep(100); + timeout--; + } + if (ret_val != 0) + goto out; + + ret_val = igb_read_sfp_data_byte(hw, + E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_ETH_FLAGS_OFFSET), + (u8 *)eth_flags); + if (ret_val != 0) + goto out; + + /* Check if there is some SFP module plugged and powered */ + if ((tranceiver_type == E1000_SFF_IDENTIFIER_SFP) || + (tranceiver_type == E1000_SFF_IDENTIFIER_SFF)) { + dev_spec->module_plugged = true; + if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) { + hw->phy.media_type = e1000_media_type_internal_serdes; + } else if (eth_flags->e100_base_fx) { + dev_spec->sgmii_active = true; + hw->phy.media_type = e1000_media_type_internal_serdes; + } else if (eth_flags->e1000_base_t) { + dev_spec->sgmii_active = true; + hw->phy.media_type = e1000_media_type_copper; + } else { + hw->phy.media_type = e1000_media_type_unknown; + hw_dbg("PHY module has not been recognized\n"); + goto out; + } + } else { + hw->phy.media_type = e1000_media_type_unknown; + } + ret_val = 0; +out: + /* Restore I2C interface setting */ + wr32(E1000_CTRL_EXT, ctrl_ext); + return ret_val; +} + static s32 igb_get_invariants_82575(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; struct e1000_dev_spec_82575 * dev_spec = &hw->dev_spec._82575; s32 ret_val; u32 ctrl_ext = 0; + u32 link_mode = 0; switch (hw->device_id) { case E1000_DEV_ID_82575EB_COPPER: @@ -470,16 +540,56 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw) */ hw->phy.media_type = e1000_media_type_copper; dev_spec->sgmii_active = false; + dev_spec->module_plugged = false; ctrl_ext = rd32(E1000_CTRL_EXT); - switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { - case E1000_CTRL_EXT_LINK_MODE_SGMII: - dev_spec->sgmii_active = true; - break; + + link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK; + switch (link_mode) { case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: - case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES: hw->phy.media_type = e1000_media_type_internal_serdes; break; + case E1000_CTRL_EXT_LINK_MODE_SGMII: + /* Get phy control interface type set (MDIO vs. I2C)*/ + if (igb_sgmii_uses_mdio_82575(hw)) { + hw->phy.media_type = e1000_media_type_copper; + dev_spec->sgmii_active = true; + break; + } + /* fall through for I2C based SGMII */ + case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES: + /* read media type from SFP EEPROM */ + ret_val = igb_set_sfp_media_type_82575(hw); + if ((ret_val != 0) || + (hw->phy.media_type == e1000_media_type_unknown)) { + /* If media type was not identified then return media + * type defined by the CTRL_EXT settings. + */ + hw->phy.media_type = e1000_media_type_internal_serdes; + + if (link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII) { + hw->phy.media_type = e1000_media_type_copper; + dev_spec->sgmii_active = true; + } + + break; + } + + /* do not change link mode for 100BaseFX */ + if (dev_spec->eth_flags.e100_base_fx) + break; + + /* change current link mode setting */ + ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK; + + if (hw->phy.media_type == e1000_media_type_copper) + ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII; + else + ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES; + + wr32(E1000_CTRL_EXT, ctrl_ext); + + break; default: break; } diff --git a/drivers/net/ethernet/intel/igb/e1000_defines.h b/drivers/net/ethernet/intel/igb/e1000_defines.h index aa176490ddbc..aa201abb8ad2 100644 --- a/drivers/net/ethernet/intel/igb/e1000_defines.h +++ b/drivers/net/ethernet/intel/igb/e1000_defines.h @@ -61,20 +61,22 @@ /* Clear Interrupt timers after IMS clear */ /* packet buffer parity error detection enabled */ /* descriptor FIFO parity error detection enable */ -#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */ -#define E1000_I2CCMD_REG_ADDR_SHIFT 16 -#define E1000_I2CCMD_PHY_ADDR_SHIFT 24 -#define E1000_I2CCMD_OPCODE_READ 0x08000000 -#define E1000_I2CCMD_OPCODE_WRITE 0x00000000 -#define E1000_I2CCMD_READY 0x20000000 -#define E1000_I2CCMD_ERROR 0x80000000 -#define E1000_MAX_SGMII_PHY_REG_ADDR 255 -#define E1000_I2CCMD_PHY_TIMEOUT 200 -#define E1000_IVAR_VALID 0x80 -#define E1000_GPIE_NSICR 0x00000001 -#define E1000_GPIE_MSIX_MODE 0x00000010 -#define E1000_GPIE_EIAME 0x40000000 -#define E1000_GPIE_PBA 0x80000000 +#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */ +#define E1000_I2CCMD_REG_ADDR_SHIFT 16 +#define E1000_I2CCMD_PHY_ADDR_SHIFT 24 +#define E1000_I2CCMD_OPCODE_READ 0x08000000 +#define E1000_I2CCMD_OPCODE_WRITE 0x00000000 +#define E1000_I2CCMD_READY 0x20000000 +#define E1000_I2CCMD_ERROR 0x80000000 +#define E1000_I2CCMD_SFP_DATA_ADDR(a) (0x0000 + (a)) +#define E1000_I2CCMD_SFP_DIAG_ADDR(a) (0x0100 + (a)) +#define E1000_MAX_SGMII_PHY_REG_ADDR 255 +#define E1000_I2CCMD_PHY_TIMEOUT 200 +#define E1000_IVAR_VALID 0x80 +#define E1000_GPIE_NSICR 0x00000001 +#define E1000_GPIE_MSIX_MODE 0x00000010 +#define E1000_GPIE_EIAME 0x40000000 +#define E1000_GPIE_PBA 0x80000000 /* Receive Descriptor bit definitions */ #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ diff --git a/drivers/net/ethernet/intel/igb/e1000_hw.h b/drivers/net/ethernet/intel/igb/e1000_hw.h index 488abb24a54f..94d7866b9c20 100644 --- a/drivers/net/ethernet/intel/igb/e1000_hw.h +++ b/drivers/net/ethernet/intel/igb/e1000_hw.h @@ -528,6 +528,8 @@ struct e1000_dev_spec_82575 { bool global_device_reset; bool eee_disable; bool clear_semaphore_once; + struct e1000_sfp_flags eth_flags; + bool module_plugged; }; struct e1000_hw { diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.c b/drivers/net/ethernet/intel/igb/e1000_phy.c index 115b0da6e013..1d6a401cc5d4 100644 --- a/drivers/net/ethernet/intel/igb/e1000_phy.c +++ b/drivers/net/ethernet/intel/igb/e1000_phy.c @@ -341,6 +341,130 @@ s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data) } /** + * igb_read_sfp_data_byte - Reads SFP module data. + * @hw: pointer to the HW structure + * @offset: byte location offset to be read + * @data: read data buffer pointer + * + * Reads one byte from SFP module data stored + * in SFP resided EEPROM memory or SFP diagnostic area. + * Function should be called with + * E1000_I2CCMD_SFP_DATA_ADDR(<byte offset>) for SFP module database access + * E1000_I2CCMD_SFP_DIAG_ADDR(<byte offset>) for SFP diagnostics parameters + * access + **/ +s32 igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data) +{ + u32 i = 0; + u32 i2ccmd = 0; + u32 data_local = 0; + + if (offset > E1000_I2CCMD_SFP_DIAG_ADDR(255)) { + hw_dbg("I2CCMD command address exceeds upper limit\n"); + return -E1000_ERR_PHY; + } + + /* Set up Op-code, EEPROM Address,in the I2CCMD + * register. The MAC will take care of interfacing with the + * EEPROM to retrieve the desired data. + */ + i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) | + E1000_I2CCMD_OPCODE_READ); + + wr32(E1000_I2CCMD, i2ccmd); + + /* Poll the ready bit to see if the I2C read completed */ + for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) { + udelay(50); + data_local = rd32(E1000_I2CCMD); + if (data_local & E1000_I2CCMD_READY) + break; + } + if (!(data_local & E1000_I2CCMD_READY)) { + hw_dbg("I2CCMD Read did not complete\n"); + return -E1000_ERR_PHY; + } + if (data_local & E1000_I2CCMD_ERROR) { + hw_dbg("I2CCMD Error bit set\n"); + return -E1000_ERR_PHY; + } + *data = (u8) data_local & 0xFF; + + return 0; +} + +/** + * e1000_write_sfp_data_byte - Writes SFP module data. + * @hw: pointer to the HW structure + * @offset: byte location offset to write to + * @data: data to write + * + * Writes one byte to SFP module data stored + * in SFP resided EEPROM memory or SFP diagnostic area. + * Function should be called with + * E1000_I2CCMD_SFP_DATA_ADDR(<byte offset>) for SFP module database access + * E1000_I2CCMD_SFP_DIAG_ADDR(<byte offset>) for SFP diagnostics parameters + * access + **/ +s32 e1000_write_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 data) +{ + u32 i = 0; + u32 i2ccmd = 0; + u32 data_local = 0; + + if (offset > E1000_I2CCMD_SFP_DIAG_ADDR(255)) { + hw_dbg("I2CCMD command address exceeds upper limit\n"); + return -E1000_ERR_PHY; + } + /* The programming interface is 16 bits wide + * so we need to read the whole word first + * then update appropriate byte lane and write + * the updated word back. + */ + /* Set up Op-code, EEPROM Address,in the I2CCMD + * register. The MAC will take care of interfacing + * with an EEPROM to write the data given. + */ + i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) | + E1000_I2CCMD_OPCODE_READ); + /* Set a command to read single word */ + wr32(E1000_I2CCMD, i2ccmd); + for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) { + udelay(50); + /* Poll the ready bit to see if lastly + * launched I2C operation completed + */ + i2ccmd = rd32(E1000_I2CCMD); + if (i2ccmd & E1000_I2CCMD_READY) { + /* Check if this is READ or WRITE phase */ + if ((i2ccmd & E1000_I2CCMD_OPCODE_READ) == + E1000_I2CCMD_OPCODE_READ) { + /* Write the selected byte + * lane and update whole word + */ + data_local = i2ccmd & 0xFF00; + data_local |= data; + i2ccmd = ((offset << + E1000_I2CCMD_REG_ADDR_SHIFT) | + E1000_I2CCMD_OPCODE_WRITE | data_local); + wr32(E1000_I2CCMD, i2ccmd); + } else { + break; + } + } + } + if (!(i2ccmd & E1000_I2CCMD_READY)) { + hw_dbg("I2CCMD Write did not complete\n"); + return -E1000_ERR_PHY; + } + if (i2ccmd & E1000_I2CCMD_ERROR) { + hw_dbg("I2CCMD Error bit set\n"); + return -E1000_ERR_PHY; + } + return 0; +} + +/** * igb_read_phy_reg_igp - Read igp PHY register * @hw: pointer to the HW structure * @offset: register offset to be read diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.h b/drivers/net/ethernet/intel/igb/e1000_phy.h index 784fd1c40989..6a0873f2095a 100644 --- a/drivers/net/ethernet/intel/igb/e1000_phy.h +++ b/drivers/net/ethernet/intel/igb/e1000_phy.h @@ -69,6 +69,8 @@ s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data); s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data); s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data); s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data); +s32 igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data); +s32 e1000_write_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 data); s32 igb_copper_link_setup_82580(struct e1000_hw *hw); s32 igb_get_phy_info_82580(struct e1000_hw *hw); s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw); @@ -157,4 +159,22 @@ s32 igb_check_polarity_m88(struct e1000_hw *hw); #define GS40G_CS_POWER_DOWN 0x0002 #define GS40G_LINE_LB 0x4000 +/* SFP modules ID memory locations */ +#define E1000_SFF_IDENTIFIER_OFFSET 0x00 +#define E1000_SFF_IDENTIFIER_SFF 0x02 +#define E1000_SFF_IDENTIFIER_SFP 0x03 + +#define E1000_SFF_ETH_FLAGS_OFFSET 0x06 +/* Flags for SFP modules compatible with ETH up to 1Gb */ +struct e1000_sfp_flags { + u8 e1000_base_sx:1; + u8 e1000_base_lx:1; + u8 e1000_base_cx:1; + u8 e1000_base_t:1; + u8 e100_base_lx:1; + u8 e100_base_fx:1; + u8 e10_base_bx10:1; + u8 e10_base_px:1; +}; + #endif diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c index 7876240fa74e..4e54f847ac92 100644 --- a/drivers/net/ethernet/intel/igb/igb_ethtool.c +++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c @@ -142,6 +142,8 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) { struct igb_adapter *adapter = netdev_priv(netdev); struct e1000_hw *hw = &adapter->hw; + struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; + struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags; u32 status; if (hw->phy.media_type == e1000_media_type_copper) { @@ -181,30 +183,22 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) ecmd->phy_address = hw->phy.addr; ecmd->transceiver = XCVR_INTERNAL; } else { - ecmd->supported = (SUPPORTED_1000baseT_Full | - SUPPORTED_100baseT_Full | - SUPPORTED_FIBRE | + ecmd->supported = (SUPPORTED_FIBRE | SUPPORTED_Autoneg | SUPPORTED_Pause); - if (hw->mac.type == e1000_i354) - ecmd->supported |= SUPPORTED_2500baseX_Full; - ecmd->advertising = ADVERTISED_FIBRE; - - switch (adapter->link_speed) { - case SPEED_2500: - ecmd->advertising = ADVERTISED_2500baseX_Full; - break; - case SPEED_1000: - ecmd->advertising = ADVERTISED_1000baseT_Full; - break; - case SPEED_100: - ecmd->advertising = ADVERTISED_100baseT_Full; - break; - default: - break; + if (hw->mac.type == e1000_i354) { + ecmd->supported |= SUPPORTED_2500baseX_Full; + ecmd->advertising |= ADVERTISED_2500baseX_Full; + } + if ((eth_flags->e1000_base_lx) || (eth_flags->e1000_base_sx)) { + ecmd->supported |= SUPPORTED_1000baseT_Full; + ecmd->advertising |= ADVERTISED_1000baseT_Full; + } + if (eth_flags->e100_base_fx) { + ecmd->supported |= SUPPORTED_100baseT_Full; + ecmd->advertising |= ADVERTISED_100baseT_Full; } - if (hw->mac.autoneg == 1) ecmd->advertising |= ADVERTISED_Autoneg; |