diff options
Diffstat (limited to 'drivers/net/ethernet/chelsio/cxgb/vsc7326_reg.h')
| -rw-r--r-- | drivers/net/ethernet/chelsio/cxgb/vsc7326_reg.h | 297 |
1 files changed, 297 insertions, 0 deletions
diff --git a/drivers/net/ethernet/chelsio/cxgb/vsc7326_reg.h b/drivers/net/ethernet/chelsio/cxgb/vsc7326_reg.h new file mode 100644 index 000000000000..479edbcabe68 --- /dev/null +++ b/drivers/net/ethernet/chelsio/cxgb/vsc7326_reg.h @@ -0,0 +1,297 @@ +/* $Date: 2006/04/28 19:20:17 $ $RCSfile: vsc7326_reg.h,v $ $Revision: 1.5 $ */ +#ifndef _VSC7321_REG_H_ +#define _VSC7321_REG_H_ + +/* Register definitions for Vitesse VSC7321 (Meigs II) MAC + * + * Straight off the data sheet, VMDS-10038 Rev 2.0 and + * PD0011-01-14-Meigs-II 2002-12-12 + */ + +/* Just 'cause it's in here doesn't mean it's used. */ + +#define CRA(blk,sub,adr) ((((blk) & 0x7) << 13) | (((sub) & 0xf) << 9) | (((adr) & 0xff) << 1)) + +/* System and CPU comm's registers */ +#define REG_CHIP_ID CRA(0x7,0xf,0x00) /* Chip ID */ +#define REG_BLADE_ID CRA(0x7,0xf,0x01) /* Blade ID */ +#define REG_SW_RESET CRA(0x7,0xf,0x02) /* Global Soft Reset */ +#define REG_MEM_BIST CRA(0x7,0xf,0x04) /* mem */ +#define REG_IFACE_MODE CRA(0x7,0xf,0x07) /* Interface mode */ +#define REG_MSCH CRA(0x7,0x2,0x06) /* CRC error count */ +#define REG_CRC_CNT CRA(0x7,0x2,0x0a) /* CRC error count */ +#define REG_CRC_CFG CRA(0x7,0x2,0x0b) /* CRC config */ +#define REG_SI_TRANSFER_SEL CRA(0x7,0xf,0x18) /* SI Transfer Select */ +#define REG_PLL_CLK_SPEED CRA(0x7,0xf,0x19) /* Clock Speed Selection */ +#define REG_SYS_CLK_SELECT CRA(0x7,0xf,0x1c) /* System Clock Select */ +#define REG_GPIO_CTRL CRA(0x7,0xf,0x1d) /* GPIO Control */ +#define REG_GPIO_OUT CRA(0x7,0xf,0x1e) /* GPIO Out */ +#define REG_GPIO_IN CRA(0x7,0xf,0x1f) /* GPIO In */ +#define REG_CPU_TRANSFER_SEL CRA(0x7,0xf,0x20) /* CPU Transfer Select */ +#define REG_LOCAL_DATA CRA(0x7,0xf,0xfe) /* Local CPU Data Register */ +#define REG_LOCAL_STATUS CRA(0x7,0xf,0xff) /* Local CPU Status Register */ + +/* Aggregator registers */ +#define REG_AGGR_SETUP CRA(0x7,0x1,0x00) /* Aggregator Setup */ +#define REG_PMAP_TABLE CRA(0x7,0x1,0x01) /* Port map table */ +#define REG_MPLS_BIT0 CRA(0x7,0x1,0x08) /* MPLS bit0 position */ +#define REG_MPLS_BIT1 CRA(0x7,0x1,0x09) /* MPLS bit1 position */ +#define REG_MPLS_BIT2 CRA(0x7,0x1,0x0a) /* MPLS bit2 position */ +#define REG_MPLS_BIT3 CRA(0x7,0x1,0x0b) /* MPLS bit3 position */ +#define REG_MPLS_BITMASK CRA(0x7,0x1,0x0c) /* MPLS bit mask */ +#define REG_PRE_BIT0POS CRA(0x7,0x1,0x10) /* Preamble bit0 position */ +#define REG_PRE_BIT1POS CRA(0x7,0x1,0x11) /* Preamble bit1 position */ +#define REG_PRE_BIT2POS CRA(0x7,0x1,0x12) /* Preamble bit2 position */ +#define REG_PRE_BIT3POS CRA(0x7,0x1,0x13) /* Preamble bit3 position */ +#define REG_PRE_ERR_CNT CRA(0x7,0x1,0x14) /* Preamble parity error count */ + +/* BIST registers */ +/*#define REG_RAM_BIST_CMD CRA(0x7,0x2,0x00)*/ /* RAM BIST Command Register */ +/*#define REG_RAM_BIST_RESULT CRA(0x7,0x2,0x01)*/ /* RAM BIST Read Status/Result */ +#define REG_RAM_BIST_CMD CRA(0x7,0x1,0x00) /* RAM BIST Command Register */ +#define REG_RAM_BIST_RESULT CRA(0x7,0x1,0x01) /* RAM BIST Read Status/Result */ +#define BIST_PORT_SELECT 0x00 /* BIST port select */ +#define BIST_COMMAND 0x01 /* BIST enable/disable */ +#define BIST_STATUS 0x02 /* BIST operation status */ +#define BIST_ERR_CNT_LSB 0x03 /* BIST error count lo 8b */ +#define BIST_ERR_CNT_MSB 0x04 /* BIST error count hi 8b */ +#define BIST_ERR_SEL_LSB 0x05 /* BIST error select lo 8b */ +#define BIST_ERR_SEL_MSB 0x06 /* BIST error select hi 8b */ +#define BIST_ERROR_STATE 0x07 /* BIST engine internal state */ +#define BIST_ERR_ADR0 0x08 /* BIST error address lo 8b */ +#define BIST_ERR_ADR1 0x09 /* BIST error address lomid 8b */ +#define BIST_ERR_ADR2 0x0a /* BIST error address himid 8b */ +#define BIST_ERR_ADR3 0x0b /* BIST error address hi 8b */ + +/* FIFO registers + * ie = 0 for ingress, 1 for egress + * fn = FIFO number, 0-9 + */ +#define REG_TEST(ie,fn) CRA(0x2,ie&1,0x00+fn) /* Mode & Test Register */ +#define REG_TOP_BOTTOM(ie,fn) CRA(0x2,ie&1,0x10+fn) /* FIFO Buffer Top & Bottom */ +#define REG_TAIL(ie,fn) CRA(0x2,ie&1,0x20+fn) /* FIFO Write Pointer */ +#define REG_HEAD(ie,fn) CRA(0x2,ie&1,0x30+fn) /* FIFO Read Pointer */ +#define REG_HIGH_LOW_WM(ie,fn) CRA(0x2,ie&1,0x40+fn) /* Flow Control Water Marks */ +#define REG_CT_THRHLD(ie,fn) CRA(0x2,ie&1,0x50+fn) /* Cut Through Threshold */ +#define REG_FIFO_DROP_CNT(ie,fn) CRA(0x2,ie&1,0x60+fn) /* Drop & CRC Error Counter */ +#define REG_DEBUG_BUF_CNT(ie,fn) CRA(0x2,ie&1,0x70+fn) /* Input Side Debug Counter */ +#define REG_BUCKI(fn) CRA(0x2,2,0x20+fn) /* Input Side Debug Counter */ +#define REG_BUCKE(fn) CRA(0x2,3,0x20+fn) /* Input Side Debug Counter */ + +/* Traffic shaper buckets + * ie = 0 for ingress, 1 for egress + * bn = bucket number 0-10 (yes, 11 buckets) + */ +/* OK, this one's kinda ugly. Some hardware designers are perverse. */ +#define REG_TRAFFIC_SHAPER_BUCKET(ie,bn) CRA(0x2,ie&1,0x0a + (bn>7) | ((bn&7)<<4)) +#define REG_TRAFFIC_SHAPER_CONTROL(ie) CRA(0x2,ie&1,0x3b) + +#define REG_SRAM_ADR(ie) CRA(0x2,ie&1,0x0e) /* FIFO SRAM address */ +#define REG_SRAM_WR_STRB(ie) CRA(0x2,ie&1,0x1e) /* FIFO SRAM write strobe */ +#define REG_SRAM_RD_STRB(ie) CRA(0x2,ie&1,0x2e) /* FIFO SRAM read strobe */ +#define REG_SRAM_DATA_0(ie) CRA(0x2,ie&1,0x3e) /* FIFO SRAM data lo 8b */ +#define REG_SRAM_DATA_1(ie) CRA(0x2,ie&1,0x4e) /* FIFO SRAM data lomid 8b */ +#define REG_SRAM_DATA_2(ie) CRA(0x2,ie&1,0x5e) /* FIFO SRAM data himid 8b */ +#define REG_SRAM_DATA_3(ie) CRA(0x2,ie&1,0x6e) /* FIFO SRAM data hi 8b */ +#define REG_SRAM_DATA_BLK_TYPE(ie) CRA(0x2,ie&1,0x7e) /* FIFO SRAM tag */ +/* REG_ING_CONTROL equals REG_CONTROL with ie = 0, likewise REG_EGR_CONTROL is ie = 1 */ +#define REG_CONTROL(ie) CRA(0x2,ie&1,0x0f) /* FIFO control */ +#define REG_ING_CONTROL CRA(0x2,0x0,0x0f) /* Ingress control (alias) */ +#define REG_EGR_CONTROL CRA(0x2,0x1,0x0f) /* Egress control (alias) */ +#define REG_AGE_TIMER(ie) CRA(0x2,ie&1,0x1f) /* Aging timer */ +#define REG_AGE_INC(ie) CRA(0x2,ie&1,0x2f) /* Aging increment */ +#define DEBUG_OUT(ie) CRA(0x2,ie&1,0x3f) /* Output debug counter control */ +#define DEBUG_CNT(ie) CRA(0x2,ie&1,0x4f) /* Output debug counter */ + +/* SPI4 interface */ +#define REG_SPI4_MISC CRA(0x5,0x0,0x00) /* Misc Register */ +#define REG_SPI4_STATUS CRA(0x5,0x0,0x01) /* CML Status */ +#define REG_SPI4_ING_SETUP0 CRA(0x5,0x0,0x02) /* Ingress Status Channel Setup */ +#define REG_SPI4_ING_SETUP1 CRA(0x5,0x0,0x03) /* Ingress Data Training Setup */ +#define REG_SPI4_ING_SETUP2 CRA(0x5,0x0,0x04) /* Ingress Data Burst Size Setup */ +#define REG_SPI4_EGR_SETUP0 CRA(0x5,0x0,0x05) /* Egress Status Channel Setup */ +#define REG_SPI4_DBG_CNT(n) CRA(0x5,0x0,0x10+n) /* Debug counters 0-9 */ +#define REG_SPI4_DBG_SETUP CRA(0x5,0x0,0x1A) /* Debug counters setup */ +#define REG_SPI4_TEST CRA(0x5,0x0,0x20) /* Test Setup Register */ +#define REG_TPGEN_UP0 CRA(0x5,0x0,0x21) /* Test Pattern generator user pattern 0 */ +#define REG_TPGEN_UP1 CRA(0x5,0x0,0x22) /* Test Pattern generator user pattern 1 */ +#define REG_TPCHK_UP0 CRA(0x5,0x0,0x23) /* Test Pattern checker user pattern 0 */ +#define REG_TPCHK_UP1 CRA(0x5,0x0,0x24) /* Test Pattern checker user pattern 1 */ +#define REG_TPSAM_P0 CRA(0x5,0x0,0x25) /* Sampled pattern 0 */ +#define REG_TPSAM_P1 CRA(0x5,0x0,0x26) /* Sampled pattern 1 */ +#define REG_TPERR_CNT CRA(0x5,0x0,0x27) /* Pattern checker error counter */ +#define REG_SPI4_STICKY CRA(0x5,0x0,0x30) /* Sticky bits register */ +#define REG_SPI4_DBG_INH CRA(0x5,0x0,0x31) /* Core egress & ingress inhibit */ +#define REG_SPI4_DBG_STATUS CRA(0x5,0x0,0x32) /* Sampled ingress status */ +#define REG_SPI4_DBG_GRANT CRA(0x5,0x0,0x33) /* Ingress cranted credit value */ + +#define REG_SPI4_DESKEW CRA(0x5,0x0,0x43) /* Ingress cranted credit value */ + +/* 10GbE MAC Block Registers */ +/* Note that those registers that are exactly the same for 10GbE as for + * tri-speed are only defined with the version that needs a port number. + * Pass 0xa in those cases. + * + * Also note that despite the presence of a MAC address register, this part + * does no ingress MAC address filtering. That register is used only for + * pause frame detection and generation. + */ +/* 10GbE specific, and different from tri-speed */ +#define REG_MISC_10G CRA(0x1,0xa,0x00) /* Misc 10GbE setup */ +#define REG_PAUSE_10G CRA(0x1,0xa,0x01) /* Pause register */ +#define REG_NORMALIZER_10G CRA(0x1,0xa,0x05) /* 10G normalizer */ +#define REG_STICKY_RX CRA(0x1,0xa,0x06) /* RX debug register */ +#define REG_DENORM_10G CRA(0x1,0xa,0x07) /* Denormalizer */ +#define REG_STICKY_TX CRA(0x1,0xa,0x08) /* TX sticky bits */ +#define REG_MAX_RXHIGH CRA(0x1,0xa,0x0a) /* XGMII lane 0-3 debug */ +#define REG_MAX_RXLOW CRA(0x1,0xa,0x0b) /* XGMII lane 4-7 debug */ +#define REG_MAC_TX_STICKY CRA(0x1,0xa,0x0c) /* MAC Tx state sticky debug */ +#define REG_MAC_TX_RUNNING CRA(0x1,0xa,0x0d) /* MAC Tx state running debug */ +#define REG_TX_ABORT_AGE CRA(0x1,0xa,0x14) /* Aged Tx frames discarded */ +#define REG_TX_ABORT_SHORT CRA(0x1,0xa,0x15) /* Short Tx frames discarded */ +#define REG_TX_ABORT_TAXI CRA(0x1,0xa,0x16) /* Taxi error frames discarded */ +#define REG_TX_ABORT_UNDERRUN CRA(0x1,0xa,0x17) /* Tx Underrun abort counter */ +#define REG_TX_DENORM_DISCARD CRA(0x1,0xa,0x18) /* Tx denormalizer discards */ +#define REG_XAUI_STAT_A CRA(0x1,0xa,0x20) /* XAUI status A */ +#define REG_XAUI_STAT_B CRA(0x1,0xa,0x21) /* XAUI status B */ +#define REG_XAUI_STAT_C CRA(0x1,0xa,0x22) /* XAUI status C */ +#define REG_XAUI_CONF_A CRA(0x1,0xa,0x23) /* XAUI configuration A */ +#define REG_XAUI_CONF_B CRA(0x1,0xa,0x24) /* XAUI configuration B */ +#define REG_XAUI_CODE_GRP_CNT CRA(0x1,0xa,0x25) /* XAUI code group error count */ +#define REG_XAUI_CONF_TEST_A CRA(0x1,0xa,0x26) /* XAUI test register A */ +#define REG_PDERRCNT CRA(0x1,0xa,0x27) /* XAUI test register B */ + +/* pn = port number 0-9 for tri-speed, 10 for 10GbE */ +/* Both tri-speed and 10GbE */ +#define REG_MAX_LEN(pn) CRA(0x1,pn,0x02) /* Max length */ +#define REG_MAC_HIGH_ADDR(pn) CRA(0x1,pn,0x03) /* Upper 24 bits of MAC addr */ +#define REG_MAC_LOW_ADDR(pn) CRA(0x1,pn,0x04) /* Lower 24 bits of MAC addr */ + +/* tri-speed only + * pn = port number, 0-9 + */ +#define REG_MODE_CFG(pn) CRA(0x1,pn,0x00) /* Mode configuration */ +#define REG_PAUSE_CFG(pn) CRA(0x1,pn,0x01) /* Pause configuration */ +#define REG_NORMALIZER(pn) CRA(0x1,pn,0x05) /* Normalizer */ +#define REG_TBI_STATUS(pn) CRA(0x1,pn,0x06) /* TBI status */ +#define REG_PCS_STATUS_DBG(pn) CRA(0x1,pn,0x07) /* PCS status debug */ +#define REG_PCS_CTRL(pn) CRA(0x1,pn,0x08) /* PCS control */ +#define REG_TBI_CONFIG(pn) CRA(0x1,pn,0x09) /* TBI configuration */ +#define REG_STICK_BIT(pn) CRA(0x1,pn,0x0a) /* Sticky bits */ +#define REG_DEV_SETUP(pn) CRA(0x1,pn,0x0b) /* MAC clock/reset setup */ +#define REG_DROP_CNT(pn) CRA(0x1,pn,0x0c) /* Drop counter */ +#define REG_PORT_POS(pn) CRA(0x1,pn,0x0d) /* Preamble port position */ +#define REG_PORT_FAIL(pn) CRA(0x1,pn,0x0e) /* Preamble port position */ +#define REG_SERDES_CONF(pn) CRA(0x1,pn,0x0f) /* SerDes configuration */ +#define REG_SERDES_TEST(pn) CRA(0x1,pn,0x10) /* SerDes test */ +#define REG_SERDES_STAT(pn) CRA(0x1,pn,0x11) /* SerDes status */ +#define REG_SERDES_COM_CNT(pn) CRA(0x1,pn,0x12) /* SerDes comma counter */ +#define REG_DENORM(pn) CRA(0x1,pn,0x15) /* Frame denormalization */ +#define REG_DBG(pn) CRA(0x1,pn,0x16) /* Device 1G debug */ +#define REG_TX_IFG(pn) CRA(0x1,pn,0x18) /* Tx IFG config */ +#define REG_HDX(pn) CRA(0x1,pn,0x19) /* Half-duplex config */ + +/* Statistics */ +/* CRA(0x4,pn,reg) */ +/* reg below */ +/* pn = port number, 0-a, a = 10GbE */ + +enum { + RxInBytes = 0x00, // # Rx in octets + RxSymbolCarrier = 0x01, // Frames w/ symbol errors + RxPause = 0x02, // # pause frames received + RxUnsupOpcode = 0x03, // # control frames with unsupported opcode + RxOkBytes = 0x04, // # octets in good frames + RxBadBytes = 0x05, // # octets in bad frames + RxUnicast = 0x06, // # good unicast frames + RxMulticast = 0x07, // # good multicast frames + RxBroadcast = 0x08, // # good broadcast frames + Crc = 0x09, // # frames w/ bad CRC only + RxAlignment = 0x0a, // # frames w/ alignment err + RxUndersize = 0x0b, // # frames undersize + RxFragments = 0x0c, // # frames undersize w/ crc err + RxInRangeLengthError = 0x0d, // # frames with length error + RxOutOfRangeError = 0x0e, // # frames with illegal length field + RxOversize = 0x0f, // # frames oversize + RxJabbers = 0x10, // # frames oversize w/ crc err + RxSize64 = 0x11, // # frames 64 octets long + RxSize65To127 = 0x12, // # frames 65-127 octets + RxSize128To255 = 0x13, // # frames 128-255 + RxSize256To511 = 0x14, // # frames 256-511 + RxSize512To1023 = 0x15, // # frames 512-1023 + RxSize1024To1518 = 0x16, // # frames 1024-1518 + RxSize1519ToMax = 0x17, // # frames 1519-max + + TxOutBytes = 0x18, // # octets tx + TxPause = 0x19, // # pause frames sent + TxOkBytes = 0x1a, // # octets tx OK + TxUnicast = 0x1b, // # frames unicast + TxMulticast = 0x1c, // # frames multicast + TxBroadcast = 0x1d, // # frames broadcast + TxMultipleColl = 0x1e, // # frames tx after multiple collisions + TxLateColl = 0x1f, // # late collisions detected + TxXcoll = 0x20, // # frames lost, excessive collisions + TxDefer = 0x21, // # frames deferred on first tx attempt + TxXdefer = 0x22, // # frames excessively deferred + TxCsense = 0x23, // carrier sense errors at frame end + TxSize64 = 0x24, // # frames 64 octets long + TxSize65To127 = 0x25, // # frames 65-127 octets + TxSize128To255 = 0x26, // # frames 128-255 + TxSize256To511 = 0x27, // # frames 256-511 + TxSize512To1023 = 0x28, // # frames 512-1023 + TxSize1024To1518 = 0x29, // # frames 1024-1518 + TxSize1519ToMax = 0x2a, // # frames 1519-max + TxSingleColl = 0x2b, // # frames tx after single collision + TxBackoff2 = 0x2c, // # frames tx ok after 2 backoffs/collisions + TxBackoff3 = 0x2d, // after 3 backoffs/collisions + TxBackoff4 = 0x2e, // after 4 + TxBackoff5 = 0x2f, // after 5 + TxBackoff6 = 0x30, // after 6 + TxBackoff7 = 0x31, // after 7 + TxBackoff8 = 0x32, // after 8 + TxBackoff9 = 0x33, // after 9 + TxBackoff10 = 0x34, // after 10 + TxBackoff11 = 0x35, // after 11 + TxBackoff12 = 0x36, // after 12 + TxBackoff13 = 0x37, // after 13 + TxBackoff14 = 0x38, // after 14 + TxBackoff15 = 0x39, // after 15 + TxUnderrun = 0x3a, // # frames dropped from underrun + // Hole. See REG_RX_XGMII_PROT_ERR below. + RxIpgShrink = 0x3c, // # of IPG shrinks detected + // Duplicate. See REG_STAT_STICKY10G below. + StatSticky1G = 0x3e, // tri-speed sticky bits + StatInit = 0x3f // Clear all statistics +}; + +#define REG_RX_XGMII_PROT_ERR CRA(0x4,0xa,0x3b) /* # protocol errors detected on XGMII interface */ +#define REG_STAT_STICKY10G CRA(0x4,0xa,StatSticky1G) /* 10GbE sticky bits */ + +#define REG_RX_OK_BYTES(pn) CRA(0x4,pn,RxOkBytes) +#define REG_RX_BAD_BYTES(pn) CRA(0x4,pn,RxBadBytes) +#define REG_TX_OK_BYTES(pn) CRA(0x4,pn,TxOkBytes) + +/* MII-Management Block registers */ +/* These are for MII-M interface 0, which is the bidirectional LVTTL one. If + * we hooked up to the one with separate directions, the middle 0x0 needs to + * change to 0x1. And the current errata states that MII-M 1 doesn't work. + */ + +#define REG_MIIM_STATUS CRA(0x3,0x0,0x00) /* MII-M Status */ +#define REG_MIIM_CMD CRA(0x3,0x0,0x01) /* MII-M Command */ +#define REG_MIIM_DATA CRA(0x3,0x0,0x02) /* MII-M Data */ +#define REG_MIIM_PRESCALE CRA(0x3,0x0,0x03) /* MII-M MDC Prescale */ + +#define REG_ING_FFILT_UM_EN CRA(0x2, 0, 0xd) +#define REG_ING_FFILT_BE_EN CRA(0x2, 0, 0x1d) +#define REG_ING_FFILT_VAL0 CRA(0x2, 0, 0x2d) +#define REG_ING_FFILT_VAL1 CRA(0x2, 0, 0x3d) +#define REG_ING_FFILT_MASK0 CRA(0x2, 0, 0x4d) +#define REG_ING_FFILT_MASK1 CRA(0x2, 0, 0x5d) +#define REG_ING_FFILT_MASK2 CRA(0x2, 0, 0x6d) +#define REG_ING_FFILT_ETYPE CRA(0x2, 0, 0x7d) + + +/* Whew. */ + +#endif |