diff options
Diffstat (limited to 'drivers/mmc/host/sh_mobile_sdhi.c')
-rw-r--r-- | drivers/mmc/host/sh_mobile_sdhi.c | 194 |
1 files changed, 125 insertions, 69 deletions
diff --git a/drivers/mmc/host/sh_mobile_sdhi.c b/drivers/mmc/host/sh_mobile_sdhi.c index 9aa147959276..f750f9494410 100644 --- a/drivers/mmc/host/sh_mobile_sdhi.c +++ b/drivers/mmc/host/sh_mobile_sdhi.c @@ -28,10 +28,12 @@ #include <linux/of_device.h> #include <linux/platform_device.h> #include <linux/mmc/host.h> -#include <linux/mmc/sh_mobile_sdhi.h> #include <linux/mfd/tmio.h> #include <linux/sh_dma.h> #include <linux/delay.h> +#include <linux/pinctrl/consumer.h> +#include <linux/pinctrl/pinctrl-state.h> +#include <linux/regulator/consumer.h> #include "tmio_mmc.h" @@ -48,10 +50,8 @@ struct sh_mobile_sdhi_of_data { unsigned bus_shift; }; -static const struct sh_mobile_sdhi_of_data sh_mobile_sdhi_of_cfg[] = { - { - .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT, - }, +static const struct sh_mobile_sdhi_of_data of_default_cfg = { + .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT, }; static const struct sh_mobile_sdhi_of_data of_rcar_gen1_compatible = { @@ -62,7 +62,7 @@ static const struct sh_mobile_sdhi_of_data of_rcar_gen1_compatible = { static const struct sh_mobile_sdhi_of_data of_rcar_gen2_compatible = { .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_WRPROTECT_DISABLE | - TMIO_MMC_CLK_ACTUAL | TMIO_MMC_FAST_CLK_CHG, + TMIO_MMC_CLK_ACTUAL | TMIO_MMC_MIN_RCAR2, .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ, .dma_buswidth = DMA_SLAVE_BUSWIDTH_4_BYTES, .dma_rx_offset = 0x2000, @@ -70,17 +70,16 @@ static const struct sh_mobile_sdhi_of_data of_rcar_gen2_compatible = { static const struct sh_mobile_sdhi_of_data of_rcar_gen3_compatible = { .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_WRPROTECT_DISABLE | - TMIO_MMC_CLK_ACTUAL | TMIO_MMC_FAST_CLK_CHG, - .capabilities = MMC_CAP_SD_HIGHSPEED, + TMIO_MMC_CLK_ACTUAL | TMIO_MMC_MIN_RCAR2, + .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ, .bus_shift = 2, }; static const struct of_device_id sh_mobile_sdhi_of_match[] = { { .compatible = "renesas,sdhi-shmobile" }, - { .compatible = "renesas,sdhi-sh7372" }, - { .compatible = "renesas,sdhi-sh73a0", .data = &sh_mobile_sdhi_of_cfg[0], }, - { .compatible = "renesas,sdhi-r8a73a4", .data = &sh_mobile_sdhi_of_cfg[0], }, - { .compatible = "renesas,sdhi-r8a7740", .data = &sh_mobile_sdhi_of_cfg[0], }, + { .compatible = "renesas,sdhi-sh73a0", .data = &of_default_cfg, }, + { .compatible = "renesas,sdhi-r8a73a4", .data = &of_default_cfg, }, + { .compatible = "renesas,sdhi-r8a7740", .data = &of_default_cfg, }, { .compatible = "renesas,sdhi-r8a7778", .data = &of_rcar_gen1_compatible, }, { .compatible = "renesas,sdhi-r8a7779", .data = &of_rcar_gen1_compatible, }, { .compatible = "renesas,sdhi-r8a7790", .data = &of_rcar_gen2_compatible, }, @@ -97,6 +96,8 @@ struct sh_mobile_sdhi { struct clk *clk; struct tmio_mmc_data mmc_data; struct tmio_mmc_dma dma_priv; + struct pinctrl *pinctrl; + struct pinctrl_state *pins_default, *pins_uhs; }; static void sh_mobile_sdhi_sdbuf_width(struct tmio_mmc_host *host, int width) @@ -131,16 +132,28 @@ static void sh_mobile_sdhi_sdbuf_width(struct tmio_mmc_host *host, int width) sd_ctrl_write16(host, EXT_ACC, val); } -static int sh_mobile_sdhi_clk_enable(struct platform_device *pdev, unsigned int *f) +static int sh_mobile_sdhi_clk_enable(struct tmio_mmc_host *host) { - struct mmc_host *mmc = platform_get_drvdata(pdev); - struct tmio_mmc_host *host = mmc_priv(mmc); + struct mmc_host *mmc = host->mmc; struct sh_mobile_sdhi *priv = host_to_priv(host); int ret = clk_prepare_enable(priv->clk); if (ret < 0) return ret; - *f = clk_get_rate(priv->clk); + /* + * The clock driver may not know what maximum frequency + * actually works, so it should be set with the max-frequency + * property which will already have been read to f_max. If it + * was missing, assume the current frequency is the maximum. + */ + if (!mmc->f_max) + mmc->f_max = clk_get_rate(priv->clk); + + /* + * Minimum frequency is the minimum input clock frequency + * divided by our maximum divider. + */ + mmc->f_min = max(clk_round_rate(priv->clk, 1) / 512, 1L); /* enable 16bit data access on SDBUF as default */ sh_mobile_sdhi_sdbuf_width(host, 16); @@ -148,19 +161,92 @@ static int sh_mobile_sdhi_clk_enable(struct platform_device *pdev, unsigned int return 0; } -static void sh_mobile_sdhi_clk_disable(struct platform_device *pdev) +static unsigned int sh_mobile_sdhi_clk_update(struct tmio_mmc_host *host, + unsigned int new_clock) +{ + struct sh_mobile_sdhi *priv = host_to_priv(host); + unsigned int freq, diff, best_freq = 0, diff_min = ~0; + int i, ret; + + /* tested only on RCar Gen2+ currently; may work for others */ + if (!(host->pdata->flags & TMIO_MMC_MIN_RCAR2)) + return clk_get_rate(priv->clk); + + /* + * We want the bus clock to be as close as possible to, but no + * greater than, new_clock. As we can divide by 1 << i for + * any i in [0, 9] we want the input clock to be as close as + * possible, but no greater than, new_clock << i. + */ + for (i = min(9, ilog2(UINT_MAX / new_clock)); i >= 0; i--) { + freq = clk_round_rate(priv->clk, new_clock << i); + if (freq > (new_clock << i)) { + /* Too fast; look for a slightly slower option */ + freq = clk_round_rate(priv->clk, + (new_clock << i) / 4 * 3); + if (freq > (new_clock << i)) + continue; + } + + diff = new_clock - (freq >> i); + if (diff <= diff_min) { + best_freq = freq; + diff_min = diff; + } + } + + ret = clk_set_rate(priv->clk, best_freq); + + return ret == 0 ? best_freq : clk_get_rate(priv->clk); +} + +static void sh_mobile_sdhi_clk_disable(struct tmio_mmc_host *host) { - struct mmc_host *mmc = platform_get_drvdata(pdev); - struct tmio_mmc_host *host = mmc_priv(mmc); struct sh_mobile_sdhi *priv = host_to_priv(host); + clk_disable_unprepare(priv->clk); } +static int sh_mobile_sdhi_start_signal_voltage_switch(struct mmc_host *mmc, + struct mmc_ios *ios) +{ + struct tmio_mmc_host *host = mmc_priv(mmc); + struct sh_mobile_sdhi *priv = host_to_priv(host); + struct pinctrl_state *pin_state; + int ret; + + switch (ios->signal_voltage) { + case MMC_SIGNAL_VOLTAGE_330: + pin_state = priv->pins_default; + break; + case MMC_SIGNAL_VOLTAGE_180: + pin_state = priv->pins_uhs; + break; + default: + return -EINVAL; + } + + /* + * If anything is missing, assume signal voltage is fixed at + * 3.3V and succeed/fail accordingly. + */ + if (IS_ERR(priv->pinctrl) || IS_ERR(pin_state)) + return ios->signal_voltage == + MMC_SIGNAL_VOLTAGE_330 ? 0 : -EINVAL; + + ret = mmc_regulator_set_vqmmc(host->mmc, ios); + if (ret) + return ret; + + return pinctrl_select_state(priv->pinctrl, pin_state); +} + static int sh_mobile_sdhi_wait_idle(struct tmio_mmc_host *host) { int timeout = 1000; - while (--timeout && !(sd_ctrl_read16(host, CTL_STATUS2) & (1 << 13))) + while (--timeout && !(sd_ctrl_read16_and_16_as_32(host, CTL_STATUS) + & TMIO_STAT_SCLKDIVEN)) udelay(1); if (!timeout) { @@ -226,7 +312,6 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev) struct tmio_mmc_host *host; struct resource *res; int irq, ret, i = 0; - bool multiplexed_isr = true; struct tmio_mmc_dma *dma_priv; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -247,6 +332,14 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev) goto eprobe; } + priv->pinctrl = devm_pinctrl_get(&pdev->dev); + if (!IS_ERR(priv->pinctrl)) { + priv->pins_default = pinctrl_lookup_state(priv->pinctrl, + PINCTRL_STATE_DEFAULT); + priv->pins_uhs = pinctrl_lookup_state(priv->pinctrl, + "state_uhs"); + } + host = tmio_mmc_host_alloc(pdev); if (!host) { ret = -ENOMEM; @@ -267,8 +360,10 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev) host->dma = dma_priv; host->write16_hook = sh_mobile_sdhi_write16_hook; host->clk_enable = sh_mobile_sdhi_clk_enable; + host->clk_update = sh_mobile_sdhi_clk_update; host->clk_disable = sh_mobile_sdhi_clk_disable; host->multi_io_quirk = sh_mobile_sdhi_multi_io_quirk; + host->start_signal_voltage_switch = sh_mobile_sdhi_start_signal_voltage_switch; /* Orginally registers were 16 bit apart, could be 32 or 64 nowadays */ if (!host->bus_shift && resource_size(res) > 0x100) /* old way to determine the shift */ @@ -308,63 +403,24 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev) if (ret < 0) goto efree; - /* - * Allow one or more specific (named) ISRs or - * one or more multiplexed (un-named) ISRs. - */ - - irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_CARD_DETECT); - if (irq >= 0) { - multiplexed_isr = false; - ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_card_detect_irq, 0, - dev_name(&pdev->dev), host); - if (ret) - goto eirq; - } - - irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_SDIO); - if (irq >= 0) { - multiplexed_isr = false; - ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_sdio_irq, 0, + while (1) { + irq = platform_get_irq(pdev, i); + if (irq < 0) + break; + i++; + ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_irq, 0, dev_name(&pdev->dev), host); if (ret) goto eirq; } - irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_SDCARD); - if (irq >= 0) { - multiplexed_isr = false; - ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_sdcard_irq, 0, - dev_name(&pdev->dev), host); - if (ret) - goto eirq; - } else if (!multiplexed_isr) { - dev_err(&pdev->dev, - "Principal SD-card IRQ is missing among named interrupts\n"); + /* There must be at least one IRQ source */ + if (!i) { ret = irq; goto eirq; } - if (multiplexed_isr) { - while (1) { - irq = platform_get_irq(pdev, i); - if (irq < 0) - break; - i++; - ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_irq, 0, - dev_name(&pdev->dev), host); - if (ret) - goto eirq; - } - - /* There must be at least one IRQ source */ - if (!i) { - ret = irq; - goto eirq; - } - } - - dev_info(&pdev->dev, "%s base at 0x%08lx clock rate %u MHz\n", + dev_info(&pdev->dev, "%s base at 0x%08lx max clock rate %u MHz\n", mmc_hostname(host->mmc), (unsigned long) (platform_get_resource(pdev, IORESOURCE_MEM, 0)->start), host->mmc->f_max / 1000000); |