diff options
Diffstat (limited to 'arch/arm/plat-pxa')
| -rw-r--r-- | arch/arm/plat-pxa/Kconfig | 5 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/Makefile | 1 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/dma.c | 3 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/include/plat/mfp.h | 7 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/include/plat/ssp.h | 186 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/mfp.c | 1 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/pwm.c | 1 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/ssp.c | 224 |
8 files changed, 427 insertions, 1 deletions
diff --git a/arch/arm/plat-pxa/Kconfig b/arch/arm/plat-pxa/Kconfig index b158e98038ed..da53395a17c6 100644 --- a/arch/arm/plat-pxa/Kconfig +++ b/arch/arm/plat-pxa/Kconfig @@ -1,3 +1,8 @@ if PLAT_PXA +config PXA_SSP + tristate + help + Enable support for PXA2xx SSP ports + endif diff --git a/arch/arm/plat-pxa/Makefile b/arch/arm/plat-pxa/Makefile index f68da35f4fb3..6187edfbcb77 100644 --- a/arch/arm/plat-pxa/Makefile +++ b/arch/arm/plat-pxa/Makefile @@ -9,3 +9,4 @@ obj-$(CONFIG_PXA3xx) += mfp.o obj-$(CONFIG_ARCH_MMP) += mfp.o obj-$(CONFIG_HAVE_PWM) += pwm.o +obj-$(CONFIG_PXA_SSP) += ssp.o diff --git a/arch/arm/plat-pxa/dma.c b/arch/arm/plat-pxa/dma.c index 2975798d411f..2d3c19d7c7b1 100644 --- a/arch/arm/plat-pxa/dma.c +++ b/arch/arm/plat-pxa/dma.c @@ -14,6 +14,7 @@ #include <linux/module.h> #include <linux/init.h> +#include <linux/slab.h> #include <linux/kernel.h> #include <linux/interrupt.h> #include <linux/errno.h> @@ -244,7 +245,7 @@ static void pxa_dma_init_debugfs(void) dbgfs_chan = kmalloc(sizeof(*dbgfs_state) * num_dma_channels, GFP_KERNEL); - if (!dbgfs_state) + if (!dbgfs_chan) goto err_alloc; chandir = debugfs_create_dir("channels", dbgfs_root); diff --git a/arch/arm/plat-pxa/include/plat/mfp.h b/arch/arm/plat-pxa/include/plat/mfp.h index 857a6839071c..9e604c80618f 100644 --- a/arch/arm/plat-pxa/include/plat/mfp.h +++ b/arch/arm/plat-pxa/include/plat/mfp.h @@ -316,6 +316,13 @@ enum { MFP_PIN_PMIC_INT, MFP_PIN_RDY, + /* additional pins on MMP2 */ + MFP_PIN_TWSI1_SCL, + MFP_PIN_TWSI1_SDA, + MFP_PIN_TWSI4_SCL, + MFP_PIN_TWSI4_SDA, + MFP_PIN_CLK_REQ, + MFP_PIN_MAX, }; diff --git a/arch/arm/plat-pxa/include/plat/ssp.h b/arch/arm/plat-pxa/include/plat/ssp.h new file mode 100644 index 000000000000..fe43150690ed --- /dev/null +++ b/arch/arm/plat-pxa/include/plat/ssp.h @@ -0,0 +1,186 @@ +/* + * ssp.h + * + * Copyright (C) 2003 Russell King, All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This driver supports the following PXA CPU/SSP ports:- + * + * PXA250 SSP + * PXA255 SSP, NSSP + * PXA26x SSP, NSSP, ASSP + * PXA27x SSP1, SSP2, SSP3 + * PXA3xx SSP1, SSP2, SSP3, SSP4 + */ + +#ifndef __ASM_ARCH_SSP_H +#define __ASM_ARCH_SSP_H + +#include <linux/list.h> +#include <linux/io.h> + +/* + * SSP Serial Port Registers + * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different. + * PXA255, PXA26x and PXA27x have extra ports, registers and bits. + */ + +#define SSCR0 (0x00) /* SSP Control Register 0 */ +#define SSCR1 (0x04) /* SSP Control Register 1 */ +#define SSSR (0x08) /* SSP Status Register */ +#define SSITR (0x0C) /* SSP Interrupt Test Register */ +#define SSDR (0x10) /* SSP Data Write/Data Read Register */ + +#define SSTO (0x28) /* SSP Time Out Register */ +#define SSPSP (0x2C) /* SSP Programmable Serial Protocol */ +#define SSTSA (0x30) /* SSP Tx Timeslot Active */ +#define SSRSA (0x34) /* SSP Rx Timeslot Active */ +#define SSTSS (0x38) /* SSP Timeslot Status */ +#define SSACD (0x3C) /* SSP Audio Clock Divider */ +#define SSACDD (0x40) /* SSP Audio Clock Dither Divider */ + +/* Common PXA2xx bits first */ +#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */ +#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */ +#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */ +#define SSCR0_Motorola (0x0 << 4) /* Motorola's Serial Peripheral Interface (SPI) */ +#define SSCR0_TI (0x1 << 4) /* Texas Instruments' Synchronous Serial Protocol (SSP) */ +#define SSCR0_National (0x2 << 4) /* National Microwire */ +#define SSCR0_ECS (1 << 6) /* External clock select */ +#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */ +#define SSCR0_SCR(x) ((x) << 8) /* Serial Clock Rate (mask) */ + +/* PXA27x, PXA3xx */ +#define SSCR0_EDSS (1 << 20) /* Extended data size select */ +#define SSCR0_NCS (1 << 21) /* Network clock select */ +#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun interrupt mask */ +#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun interrupt mask */ +#define SSCR0_FRDC (0x07000000) /* Frame rate divider control (mask) */ +#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24) /* Time slots per frame [1..8] */ +#define SSCR0_FPCKE (1 << 29) /* FIFO packing enable */ +#define SSCR0_ACS (1 << 30) /* Audio clock select */ +#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */ + + +#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */ +#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */ +#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */ +#define SSCR1_SPO (1 << 3) /* Motorola SPI SSPSCLK polarity setting */ +#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */ +#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */ +#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */ +#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */ +#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */ +#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */ + +#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */ +#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */ +#define SSSR_BSY (1 << 4) /* SSP Busy */ +#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */ +#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */ +#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */ + + +/* extra bits in PXA255, PXA26x and PXA27x SSP ports */ +#define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */ +#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */ +#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */ +#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */ +#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */ +#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */ +#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */ +#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */ +#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */ +#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */ +#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */ +#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */ +#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */ +#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */ +#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */ +#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */ +#define SSCR1_IFS (1 << 16) /* Invert Frame Signal */ +#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */ +#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */ + +#define SSSR_BCE (1 << 23) /* Bit Count Error */ +#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */ +#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */ +#define SSSR_EOC (1 << 20) /* End Of Chain */ +#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */ +#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */ + + +#define SSPSP_SCMODE(x) ((x) << 0) /* Serial Bit Rate Clock Mode */ +#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */ +#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */ +#define SSPSP_STRTDLY(x) ((x) << 4) /* Start Delay */ +#define SSPSP_DMYSTRT(x) ((x) << 7) /* Dummy Start */ +#define SSPSP_SFRMDLY(x) ((x) << 9) /* Serial Frame Delay */ +#define SSPSP_SFRMWDTH(x) ((x) << 16) /* Serial Frame Width */ +#define SSPSP_DMYSTOP(x) ((x) << 23) /* Dummy Stop */ +#define SSPSP_FSRT (1 << 25) /* Frame Sync Relative Timing */ + +/* PXA3xx */ +#define SSPSP_EDMYSTRT(x) ((x) << 26) /* Extended Dummy Start */ +#define SSPSP_EDMYSTOP(x) ((x) << 28) /* Extended Dummy Stop */ +#define SSPSP_TIMING_MASK (0x7f8001f0) + +#define SSACD_SCDB (1 << 3) /* SSPSYSCLK Divider Bypass */ +#define SSACD_ACPS(x) ((x) << 4) /* Audio clock PLL select */ +#define SSACD_ACDS(x) ((x) << 0) /* Audio clock divider select */ +#define SSACD_SCDX8 (1 << 7) /* SYSCLK division ratio select */ + +enum pxa_ssp_type { + SSP_UNDEFINED = 0, + PXA25x_SSP, /* pxa 210, 250, 255, 26x */ + PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */ + PXA27x_SSP, + PXA168_SSP, +}; + +struct ssp_device { + struct platform_device *pdev; + struct list_head node; + + struct clk *clk; + void __iomem *mmio_base; + unsigned long phys_base; + + const char *label; + int port_id; + int type; + int use_count; + int irq; + int drcmr_rx; + int drcmr_tx; +}; + +/** + * pxa_ssp_write_reg - Write to a SSP register + * + * @dev: SSP device to access + * @reg: Register to write to + * @val: Value to be written. + */ +static inline void pxa_ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val) +{ + __raw_writel(val, dev->mmio_base + reg); +} + +/** + * pxa_ssp_read_reg - Read from a SSP register + * + * @dev: SSP device to access + * @reg: Register to read from + */ +static inline u32 pxa_ssp_read_reg(struct ssp_device *dev, u32 reg) +{ + return __raw_readl(dev->mmio_base + reg); +} + +struct ssp_device *pxa_ssp_request(int port, const char *label); +void pxa_ssp_free(struct ssp_device *); +#endif /* __ASM_ARCH_SSP_H */ diff --git a/arch/arm/plat-pxa/mfp.c b/arch/arm/plat-pxa/mfp.c index be58f9fe65b0..b77e018d36c1 100644 --- a/arch/arm/plat-pxa/mfp.c +++ b/arch/arm/plat-pxa/mfp.c @@ -110,6 +110,7 @@ static const unsigned long mfpr_lpm[] = { MFPR_LPM_PULL_LOW, MFPR_LPM_PULL_HIGH, MFPR_LPM_FLOAT, + MFPR_LPM_INPUT, }; /* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */ diff --git a/arch/arm/plat-pxa/pwm.c b/arch/arm/plat-pxa/pwm.c index 51dc5c8106c0..0732c6c8d511 100644 --- a/arch/arm/plat-pxa/pwm.c +++ b/arch/arm/plat-pxa/pwm.c @@ -14,6 +14,7 @@ #include <linux/module.h> #include <linux/kernel.h> #include <linux/platform_device.h> +#include <linux/slab.h> #include <linux/err.h> #include <linux/clk.h> #include <linux/io.h> diff --git a/arch/arm/plat-pxa/ssp.c b/arch/arm/plat-pxa/ssp.c new file mode 100644 index 000000000000..c6357e554aba --- /dev/null +++ b/arch/arm/plat-pxa/ssp.c @@ -0,0 +1,224 @@ +/* + * linux/arch/arm/mach-pxa/ssp.c + * + * based on linux/arch/arm/mach-sa1100/ssp.c by Russell King + * + * Copyright (C) 2003 Russell King. + * Copyright (C) 2003 Wolfson Microelectronics PLC + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * PXA2xx SSP driver. This provides the generic core for simple + * IO-based SSP applications and allows easy port setup for DMA access. + * + * Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com> + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/mutex.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/platform_device.h> +#include <linux/io.h> + +#include <asm/irq.h> +#include <mach/hardware.h> +#include <plat/ssp.h> + +static DEFINE_MUTEX(ssp_lock); +static LIST_HEAD(ssp_list); + +struct ssp_device *pxa_ssp_request(int port, const char *label) +{ + struct ssp_device *ssp = NULL; + + mutex_lock(&ssp_lock); + + list_for_each_entry(ssp, &ssp_list, node) { + if (ssp->port_id == port && ssp->use_count == 0) { + ssp->use_count++; + ssp->label = label; + break; + } + } + + mutex_unlock(&ssp_lock); + + if (&ssp->node == &ssp_list) + return NULL; + + return ssp; +} +EXPORT_SYMBOL(pxa_ssp_request); + +void pxa_ssp_free(struct ssp_device *ssp) +{ + mutex_lock(&ssp_lock); + if (ssp->use_count) { + ssp->use_count--; + ssp->label = NULL; + } else + dev_err(&ssp->pdev->dev, "device already free\n"); + mutex_unlock(&ssp_lock); +} +EXPORT_SYMBOL(pxa_ssp_free); + +static int __devinit pxa_ssp_probe(struct platform_device *pdev) +{ + const struct platform_device_id *id = platform_get_device_id(pdev); + struct resource *res; + struct ssp_device *ssp; + int ret = 0; + + ssp = kzalloc(sizeof(struct ssp_device), GFP_KERNEL); + if (ssp == NULL) { + dev_err(&pdev->dev, "failed to allocate memory"); + return -ENOMEM; + } + ssp->pdev = pdev; + + ssp->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(ssp->clk)) { + ret = PTR_ERR(ssp->clk); + goto err_free; + } + + res = platform_get_resource(pdev, IORESOURCE_DMA, 0); + if (res == NULL) { + dev_err(&pdev->dev, "no SSP RX DRCMR defined\n"); + ret = -ENODEV; + goto err_free_clk; + } + ssp->drcmr_rx = res->start; + + res = platform_get_resource(pdev, IORESOURCE_DMA, 1); + if (res == NULL) { + dev_err(&pdev->dev, "no SSP TX DRCMR defined\n"); + ret = -ENODEV; + goto err_free_clk; + } + ssp->drcmr_tx = res->start; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (res == NULL) { + dev_err(&pdev->dev, "no memory resource defined\n"); + ret = -ENODEV; + goto err_free_clk; + } + + res = request_mem_region(res->start, resource_size(res), + pdev->name); + if (res == NULL) { + dev_err(&pdev->dev, "failed to request memory resource\n"); + ret = -EBUSY; + goto err_free_clk; + } + + ssp->phys_base = res->start; + + ssp->mmio_base = ioremap(res->start, resource_size(res)); + if (ssp->mmio_base == NULL) { + dev_err(&pdev->dev, "failed to ioremap() registers\n"); + ret = -ENODEV; + goto err_free_mem; + } + + ssp->irq = platform_get_irq(pdev, 0); + if (ssp->irq < 0) { + dev_err(&pdev->dev, "no IRQ resource defined\n"); + ret = -ENODEV; + goto err_free_io; + } + + /* PXA2xx/3xx SSP ports starts from 1 and the internal pdev->id + * starts from 0, do a translation here + */ + ssp->port_id = pdev->id + 1; + ssp->use_count = 0; + ssp->type = (int)id->driver_data; + + mutex_lock(&ssp_lock); + list_add(&ssp->node, &ssp_list); + mutex_unlock(&ssp_lock); + + platform_set_drvdata(pdev, ssp); + return 0; + +err_free_io: + iounmap(ssp->mmio_base); +err_free_mem: + release_mem_region(res->start, resource_size(res)); +err_free_clk: + clk_put(ssp->clk); +err_free: + kfree(ssp); + return ret; +} + +static int __devexit pxa_ssp_remove(struct platform_device *pdev) +{ + struct resource *res; + struct ssp_device *ssp; + + ssp = platform_get_drvdata(pdev); + if (ssp == NULL) + return -ENODEV; + + iounmap(ssp->mmio_base); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(res->start, resource_size(res)); + + clk_put(ssp->clk); + + mutex_lock(&ssp_lock); + list_del(&ssp->node); + mutex_unlock(&ssp_lock); + + kfree(ssp); + return 0; +} + +static const struct platform_device_id ssp_id_table[] = { + { "pxa25x-ssp", PXA25x_SSP }, + { "pxa25x-nssp", PXA25x_NSSP }, + { "pxa27x-ssp", PXA27x_SSP }, + { "pxa168-ssp", PXA168_SSP }, + { }, +}; + +static struct platform_driver pxa_ssp_driver = { + .probe = pxa_ssp_probe, + .remove = __devexit_p(pxa_ssp_remove), + .driver = { + .owner = THIS_MODULE, + .name = "pxa2xx-ssp", + }, + .id_table = ssp_id_table, +}; + +static int __init pxa_ssp_init(void) +{ + return platform_driver_register(&pxa_ssp_driver); +} + +static void __exit pxa_ssp_exit(void) +{ + platform_driver_unregister(&pxa_ssp_driver); +} + +arch_initcall(pxa_ssp_init); +module_exit(pxa_ssp_exit); + +MODULE_DESCRIPTION("PXA SSP driver"); +MODULE_AUTHOR("Liam Girdwood"); +MODULE_LICENSE("GPL"); |