mmc: tmio: improve checkpatch cleanness

Trivial updates to improve checkpatch cleanness.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

1 files changed, 16 insertions, 17 deletions

diff --git a/include/linux/mfd/tmio.h b/include/linux/mfd/tmio.h
index c83c16b931a8..26e8f8c0a6db 100644
--- a/include/linux/mfd/tmio.h
+++ b/include/linux/mfd/tmio.h
@@ -13,15 +13,15 @@
 #define tmio_ioread16(addr) readw(addr)
 #define tmio_ioread16_rep(r, b, l) readsw(r, b, l)
 #define tmio_ioread32(addr) \
-	(((u32) readw((addr))) | (((u32) readw((addr) + 2)) << 16))
+	(((u32)readw((addr))) | (((u32)readw((addr) + 2)) << 16))
 
 #define tmio_iowrite8(val, addr) writeb((val), (addr))
 #define tmio_iowrite16(val, addr) writew((val), (addr))
 #define tmio_iowrite16_rep(r, b, l) writesw(r, b, l)
 #define tmio_iowrite32(val, addr) \
 	do { \
-	writew((val),       (addr)); \
-	writew((val) >> 16, (addr) + 2); \
+		writew((val),       (addr)); \
+		writew((val) >> 16, (addr) + 2); \
 	} while (0)
 
 #define CNF_CMD     0x04
@@ -55,57 +55,57 @@
 	} while (0)
 
 /* tmio MMC platform flags */
-#define TMIO_MMC_WRPROTECT_DISABLE	(1 << 0)
+#define TMIO_MMC_WRPROTECT_DISABLE	BIT(0)
 /*
  * Some controllers can support a 2-byte block size when the bus width
  * is configured in 4-bit mode.
  */
-#define TMIO_MMC_BLKSZ_2BYTES		(1 << 1)
+#define TMIO_MMC_BLKSZ_2BYTES		BIT(1)
 /*
  * Some controllers can support SDIO IRQ signalling.
  */
-#define TMIO_MMC_SDIO_IRQ		(1 << 2)
+#define TMIO_MMC_SDIO_IRQ		BIT(2)
 
 /* Some features are only available or tested on R-Car Gen2 or later */
-#define TMIO_MMC_MIN_RCAR2		(1 << 3)
+#define TMIO_MMC_MIN_RCAR2		BIT(3)
 
 /*
  * Some controllers require waiting for the SD bus to become
  * idle before writing to some registers.
  */
-#define TMIO_MMC_HAS_IDLE_WAIT		(1 << 4)
+#define TMIO_MMC_HAS_IDLE_WAIT		BIT(4)
 /*
  * A GPIO is used for card hotplug detection. We need an extra flag for this,
  * because 0 is a valid GPIO number too, and requiring users to specify
  * cd_gpio < 0 to disable GPIO hotplug would break backwards compatibility.
  */
-#define TMIO_MMC_USE_GPIO_CD		(1 << 5)
+#define TMIO_MMC_USE_GPIO_CD		BIT(5)
 
 /*
  * Some controllers doesn't have over 0x100 register.
  * it is used to checking accessibility of
  * CTL_SD_CARD_CLK_CTL / CTL_CLK_AND_WAIT_CTL
  */
-#define TMIO_MMC_HAVE_HIGH_REG		(1 << 6)
+#define TMIO_MMC_HAVE_HIGH_REG		BIT(6)
 
 /*
  * Some controllers have CMD12 automatically
  * issue/non-issue register
  */
-#define TMIO_MMC_HAVE_CMD12_CTRL	(1 << 7)
+#define TMIO_MMC_HAVE_CMD12_CTRL	BIT(7)
 
 /* Controller has some SDIO status bits which must be 1 */
-#define TMIO_MMC_SDIO_STATUS_SETBITS	(1 << 8)
+#define TMIO_MMC_SDIO_STATUS_SETBITS	BIT(8)
 
 /*
  * Some controllers have a 32-bit wide data port register
  */
-#define TMIO_MMC_32BIT_DATA_PORT	(1 << 9)
+#define TMIO_MMC_32BIT_DATA_PORT	BIT(9)
 
 /*
  * Some controllers allows to set SDx actual clock
  */
-#define TMIO_MMC_CLK_ACTUAL		(1 << 10)
+#define TMIO_MMC_CLK_ACTUAL		BIT(10)
 
 int tmio_core_mmc_enable(void __iomem *cnf, int shift, unsigned long base);
 int tmio_core_mmc_resume(void __iomem *cnf, int shift, unsigned long base);
@@ -146,9 +146,9 @@ struct tmio_nand_data {
 
 struct tmio_fb_data {
 	int			(*lcd_set_power)(struct platform_device *fb_dev,
-								bool on);
+						 bool on);
 	int			(*lcd_mode)(struct platform_device *fb_dev,
-					const struct fb_videomode *mode);
+					    const struct fb_videomode *mode);
 	int			num_modes;
 	struct fb_videomode	*modes;
 
@@ -157,5 +157,4 @@ struct tmio_fb_data {
 	int			width;
 };
 
-
 #endif