Merge branch 'master' into for-next

Conflicts:
	MAINTAINERS
	arch/arm/mach-omap2/pm24xx.c
	drivers/scsi/bfa/bfa_fcpim.c

Needed to update to apply fixes for which the old branch was too
outdated.

13 files changed, 95 insertions, 261 deletions

diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 821eb842795f..d13add71f72a 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -24,8 +24,8 @@ obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o
 
 # AT91RM9200 board-specific support
 obj-$(CONFIG_MACH_ONEARM)	+= board-1arm.o
-obj-$(CONFIG_ARCH_AT91RM9200DK)	+= board-dk.o
-obj-$(CONFIG_MACH_AT91RM9200EK)	+= board-ek.o
+obj-$(CONFIG_ARCH_AT91RM9200DK)	+= board-rm9200dk.o
+obj-$(CONFIG_MACH_AT91RM9200EK)	+= board-rm9200ek.o
 obj-$(CONFIG_MACH_CSB337)	+= board-csb337.o
 obj-$(CONFIG_MACH_CSB637)	+= board-csb637.o
 obj-$(CONFIG_MACH_CARMEVA)	+= board-carmeva.o
@@ -65,7 +65,7 @@ obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
 obj-$(CONFIG_MACH_CPU9G20)	+= board-cpu9krea.o
 obj-$(CONFIG_MACH_STAMP9G20)	+= board-stamp9g20.o
 obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
-obj-$(CONFIG_MACH_PCONTROL_G20)	+= board-pcontrol-g20.o
+obj-$(CONFIG_MACH_PCONTROL_G20)	+= board-pcontrol-g20.o board-stamp9g20.o
 
 # AT91SAM9260/AT91SAM9G20 board-specific support
 obj-$(CONFIG_MACH_SNAPPER_9260)	+= board-snapper9260.o
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 9338825cfcd7..7b539228e0ef 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -1106,51 +1106,6 @@ static inline void configure_usart3_pins(unsigned pins)
 static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
 struct platform_device *atmel_default_console_device;	/* the serial console device */
 
-void __init __deprecated at91_init_serial(struct at91_uart_config *config)
-{
-	int i;
-
-	/* Fill in list of supported UARTs */
-	for (i = 0; i < config->nr_tty; i++) {
-		switch (config->tty_map[i]) {
-			case 0:
-				configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
-				at91_uarts[i] = &at91rm9200_uart0_device;
-				at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
-				break;
-			case 1:
-				configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
-				at91_uarts[i] = &at91rm9200_uart1_device;
-				at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
-				break;
-			case 2:
-				configure_usart2_pins(0);
-				at91_uarts[i] = &at91rm9200_uart2_device;
-				at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
-				break;
-			case 3:
-				configure_usart3_pins(0);
-				at91_uarts[i] = &at91rm9200_uart3_device;
-				at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
-				break;
-			case 4:
-				configure_dbgu_pins();
-				at91_uarts[i] = &at91rm9200_dbgu_device;
-				at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart");
-				break;
-			default:
-				continue;
-		}
-		at91_uarts[i]->id = i;		/* update ID number to mapped ID */
-	}
-
-	/* Set serial console device */
-	if (config->console_tty < ATMEL_MAX_UART)
-		atmel_default_console_device = at91_uarts[config->console_tty];
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
-}
-
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 {
 	struct platform_device *pdev;
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index 46bdc82d3fbf..8a3fc84847c1 100644
--- a/arch/arm/mach-at91/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -39,24 +39,24 @@
 #include "generic.h"
 
 
-/*
- * Serial port configuration.
- *    0 .. 3 = USART0 .. USART3
- *    4      = DBGU
- */
-static struct at91_uart_config __initdata onearm_uart_config = {
-	.console_tty	= 0,				/* ttyS0 */
-	.nr_tty		= 3,
-	.tty_map	= { 4, 0, 1, -1, -1 },		/* ttyS0, ..., ttyS4 */
-};
-
 static void __init onearm_map_io(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
 
-	/* Setup the serial ports and console */
-	at91_init_serial(&onearm_uart_config);
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
 }
 
 static void __init onearm_init_irq(void)
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index c0ce79d431a0..d2e1f4ec1fcc 100644
--- a/arch/arm/mach-at91/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -39,17 +39,6 @@
 #include "generic.h"
 
 
-/*
- * Serial port configuration.
- *    0 .. 3 = USART0 .. USART3
- *    4      = DBGU
- */
-static struct at91_uart_config __initdata kafa_uart_config = {
-	.console_tty	= 0,				/* ttyS0 */
-	.nr_tty		= 2,
-	.tty_map	= { 4, 0, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
-};
-
 static void __init kafa_map_io(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
@@ -58,8 +47,14 @@ static void __init kafa_map_io(void)
 	/* Set up the LEDs */
 	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
 
-	/* Setup the serial ports and console */
-	at91_init_serial(&kafa_uart_config);
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
 }
 
 static void __init kafa_init_irq(void)
diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index bba5a560e02b..feb65787c30b 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -31,6 +31,7 @@
 
 #include <mach/board.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/stamp9g20.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -38,11 +39,7 @@
 
 static void __init pcontrol_g20_map_io(void)
 {
-	/* Initialize processor: 18.432 MHz crystal */
-	at91sam9260_initialize(18432000);
-
-	/* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */
-	at91_register_uart(0, 0, 0);
+	stamp9g20_map_io();
 
 	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
 	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
@@ -54,9 +51,6 @@ static void __init pcontrol_g20_map_io(void)
 
 	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
 	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 
@@ -66,38 +60,6 @@ static void __init init_irq(void)
 }
 
 
-/*
- * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB
- */
-static struct atmel_nand_data __initdata nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-};
-
-/*
- * Bus timings; unit = 7.57ns
- */
-static struct sam9_smc_config __initdata nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 3,
-};
-
 static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
 	.ncs_read_setup		= 16,
 	.nrd_setup		= 18,
@@ -138,14 +100,6 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
 	.tdf_cycles		= 1,
 } };
 
-static void __init add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &nand_smc_config);
-	at91_add_device_nand(&nand_data);
-}
-
-
 static void __init add_device_pcontrol(void)
 {
 	/* configure chip-select 4 (IO compatible to 8051  X4 ) */
@@ -156,23 +110,6 @@ static void __init add_device_pcontrol(void)
 
 
 /*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-static struct mci_platform_data __initdata mmc_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-	},
-};
-#else
-static struct at91_mmc_data __initdata mmc_data = {
-	.wire4		= 1,
-};
-#endif
-
-
-/*
  * USB Host port
  */
 static struct at91_usbh_data __initdata usbh_data = {
@@ -265,42 +202,13 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = {
 };
 
 
-/*
- * Dallas 1-Wire  DS2431
- */
-static struct w1_gpio_platform_data w1_gpio_pdata = {
-	.pin		= AT91_PIN_PA29,
-	.is_open_drain	= 1,
-};
-
-static struct platform_device w1_device = {
-	.name			= "w1-gpio",
-	.id			= -1,
-	.dev.platform_data	= &w1_gpio_pdata,
-};
-
-static void add_wire1(void)
-{
-	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-	platform_device_register(&w1_device);
-}
-
-
 static void __init pcontrol_g20_board_init(void)
 {
-	at91_add_device_serial();
-	add_device_nand();
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-	at91_add_device_mci(0, &mmc_data);
-#else
-	at91_add_device_mmc(0, &mmc_data);
-#endif
+	stamp9g20_board_init();
 	at91_add_device_usbh(&usbh_data);
 	at91_add_device_eth(&macb_data);
 	at91_add_device_i2c(pcontrol_g20_i2c_devices,
 		ARRAY_SIZE(pcontrol_g20_i2c_devices));
-	add_wire1();
 	add_device_pcontrol();
 	at91_add_device_spi(pcontrol_g20_spi_devices,
 		ARRAY_SIZE(pcontrol_g20_spi_devices));
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index 9d833bbc592d..55dad3a46547 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -43,24 +43,21 @@
 #include "generic.h"
 
 
-/*
- * Serial port configuration.
- *    0 .. 3 = USART0 .. USART3
- *    4      = DBGU
- */
-static struct at91_uart_config __initdata picotux200_uart_config = {
-	.console_tty	= 0,				/* ttyS0 */
-	.nr_tty		= 2,
-	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
-};
-
 static void __init picotux200_map_io(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91rm9200_initialize(18432000, AT91RM9200_BGA);
 
-	/* Setup the serial ports and console */
-	at91_init_serial(&picotux200_uart_config);
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			  | ATMEL_UART_RI);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
 }
 
 static void __init picotux200_init_irq(void)
@@ -77,11 +74,6 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.ports		= 1,
 };
 
-// static struct at91_udc_data __initdata picotux200_udc_data = {
-// 	.vbus_pin	= AT91_PIN_PD4,
-// 	.pullup_pin	= AT91_PIN_PD5,
-// };
-
 static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.det_pin	= AT91_PIN_PB27,
 	.slot_b		= 0,
@@ -89,21 +81,6 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.wp_pin		= AT91_PIN_PA17,
 };
 
-// static struct spi_board_info picotux200_spi_devices[] = {
-// 	{	/* DataFlash chip */
-// 		.modalias	= "mtd_dataflash",
-// 		.chip_select	= 0,
-// 		.max_speed_hz	= 15 * 1000 * 1000,
-// 	},
-// #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-// 	{	/* DataFlash card */
-// 		.modalias	= "mtd_dataflash",
-// 		.chip_select	= 3,
-// 		.max_speed_hz	= 15 * 1000 * 1000,
-// 	},
-// #endif
-// };
-
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0
 #define PICOTUX200_FLASH_SIZE	SZ_4M
 
@@ -135,21 +112,11 @@ static void __init picotux200_board_init(void)
 	at91_add_device_eth(&picotux200_eth_data);
 	/* USB Host */
 	at91_add_device_usbh(&picotux200_usbh_data);
-	/* USB Device */
-	// at91_add_device_udc(&picotux200_udc_data);
-	// at91_set_multi_drive(picotux200_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	// at91_add_device_spi(picotux200_spi_devices, ARRAY_SIZE(picotux200_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-	/* DataFlash card */
-	at91_set_gpio_output(AT91_PIN_PB22, 0);
-#else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
 	at91_add_device_mmc(0, &picotux200_mmc_data);
-#endif
 	/* NOR Flash */
 	platform_device_register(&picotux200_flash);
 }
diff --git a/arch/arm/mach-at91/board-dk.c b/arch/arm/mach-at91/board-rm9200dk.c
index e14f0e165680..4c1047c8200d 100644
--- a/arch/arm/mach-at91/board-dk.c
+++ b/arch/arm/mach-at91/board-rm9200dk.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91/board-dk.c
+ * linux/arch/arm/mach-at91/board-rm9200dk.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -91,10 +91,12 @@ static struct at91_cf_data __initdata dk_cf_data = {
 	// .vcc_pin	= ... always powered
 };
 
+#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
 static struct at91_mmc_data __initdata dk_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 };
+#endif
 
 static struct spi_board_info dk_spi_devices[] = {
 	{	/* DataFlash chip */
diff --git a/arch/arm/mach-at91/board-ek.c b/arch/arm/mach-at91/board-rm9200ek.c
index 56e92c4bbc2a..9df1be8818c0 100644
--- a/arch/arm/mach-at91/board-ek.c
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91/board-ek.c
+ * linux/arch/arm/mach-at91/board-rm9200ek.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -84,12 +84,14 @@ static struct at91_udc_data __initdata ek_udc_data = {
 	.pullup_pin	= AT91_PIN_PD5,
 };
 
+#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.det_pin	= AT91_PIN_PB27,
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
 };
+#endif
 
 static struct spi_board_info ek_spi_devices[] = {
 	{	/* DataFlash chip */
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
index 5206eef4a67e..f8902b118960 100644
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ b/arch/arm/mach-at91/board-stamp9g20.c
@@ -32,7 +32,7 @@
 #include "generic.h"
 
 
-static void __init portuxg20_map_io(void)
+void __init stamp9g20_map_io(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91sam9260_initialize(18432000);
@@ -40,6 +40,24 @@ static void __init portuxg20_map_io(void)
 	/* DGBU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
 
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init stamp9g20evb_map_io(void)
+{
+	stamp9g20_map_io();
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+						| ATMEL_UART_DTR | ATMEL_UART_DSR
+						| ATMEL_UART_DCD | ATMEL_UART_RI);
+}
+
+static void __init portuxg20_map_io(void)
+{
+	stamp9g20_map_io();
+
 	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
 	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
 						| ATMEL_UART_DTR | ATMEL_UART_DSR
@@ -56,26 +74,6 @@ static void __init portuxg20_map_io(void)
 
 	/* USART5 on ttyS6. (Rx, Tx only) */
 	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-}
-
-static void __init stamp9g20_map_io(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91sam9260_initialize(18432000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-						| ATMEL_UART_DTR | ATMEL_UART_DSR
-						| ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static void __init init_irq(void)
@@ -156,7 +154,7 @@ static struct at91_udc_data __initdata portuxg20_udc_data = {
 	.pullup_pin	= 0,		/* pull-up driven by UDC */
 };
 
-static struct at91_udc_data __initdata stamp9g20_udc_data = {
+static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
 	.pullup_pin	= 0,		/* pull-up driven by UDC */
 };
@@ -190,7 +188,7 @@ static struct gpio_led portuxg20_leds[] = {
 	}
 };
 
-static struct gpio_led stamp9g20_leds[] = {
+static struct gpio_led stamp9g20evb_leds[] = {
 	{
 		.name			= "D8",
 		.gpio			= AT91_PIN_PB18,
@@ -250,7 +248,7 @@ void add_w1(void)
 }
 
 
-static void __init generic_board_init(void)
+void __init stamp9g20_board_init(void)
 {
 	/* Serial */
 	at91_add_device_serial();
@@ -262,34 +260,40 @@ static void __init generic_board_init(void)
 #else
 	at91_add_device_mmc(0, &mmc_data);
 #endif
-	/* USB Host */
-	at91_add_device_usbh(&usbh_data);
-	/* Ethernet */
-	at91_add_device_eth(&macb_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
 	/* W1 */
 	add_w1();
 }
 
 static void __init portuxg20_board_init(void)
 {
-	generic_board_init();
-	/* SPI */
-	at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices));
+	stamp9g20_board_init();
+	/* USB Host */
+	at91_add_device_usbh(&usbh_data);
 	/* USB Device */
 	at91_add_device_udc(&portuxg20_udc_data);
+	/* Ethernet */
+	at91_add_device_eth(&macb_data);
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
+	/* SPI */
+	at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices));
 	/* LEDs */
 	at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds));
 }
 
-static void __init stamp9g20_board_init(void)
+static void __init stamp9g20evb_board_init(void)
 {
-	generic_board_init();
+	stamp9g20_board_init();
+	/* USB Host */
+	at91_add_device_usbh(&usbh_data);
 	/* USB Device */
-	at91_add_device_udc(&stamp9g20_udc_data);
+	at91_add_device_udc(&stamp9g20evb_udc_data);
+	/* Ethernet */
+	at91_add_device_eth(&macb_data);
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
 	/* LEDs */
-	at91_gpio_leds(stamp9g20_leds, ARRAY_SIZE(stamp9g20_leds));
+	at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
 }
 
 MACHINE_START(PORTUXG20, "taskit PortuxG20")
@@ -305,7 +309,7 @@ MACHINE_START(STAMP9G20, "taskit Stamp9G20")
 	/* Maintainer: taskit GmbH */
 	.boot_params	= AT91_SDRAM_BASE + 0x100,
 	.timer		= &at91sam926x_timer,
-	.map_io		= stamp9g20_map_io,
+	.map_io		= stamp9g20evb_map_io,
 	.init_irq	= init_irq,
-	.init_machine	= stamp9g20_board_init,
+	.init_machine	= stamp9g20evb_board_init,
 MACHINE_END
diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c
index 89df00a9d2f7..e0f0080eb639 100644
--- a/arch/arm/mach-at91/board-yl-9200.c
+++ b/arch/arm/mach-at91/board-yl-9200.c
@@ -387,7 +387,7 @@ static struct spi_board_info yl9200_spi_devices[] = {
  * EPSON S1D13806 FB (discontinued chip)
  * EPSON S1D13506 FB
  */
-#if defined(CONFIG_FB_S1D135XX) || defined(CONFIG_FB_S1D13XXX_MODULE)
+#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
 #include <video/s1d13xxxfb.h>
 
 
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index 7525cee3983f..9113da6845f1 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -658,7 +658,7 @@ static void __init at91_upll_usbfs_clock_init(unsigned long main_clock)
 	/* Now set uhpck values */
 	uhpck.parent = &utmi_clk;
 	uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
-	uhpck.rate_hz = utmi_clk.parent->rate_hz;
+	uhpck.rate_hz = utmi_clk.rate_hz;
 	uhpck.rate_hz /= 1 + ((at91_sys_read(AT91_PMC_USB) & AT91_PMC_OHCIUSBDIV) >> 8);
 }
 
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 58528aa9c8a8..2b499eb343a1 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -137,13 +137,7 @@ extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_de
 extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
 extern void __init at91_set_serial_console(unsigned portnr);
 
-struct at91_uart_config {
-	unsigned short	console_tty;	/* tty number of serial console */
-	unsigned short	nr_tty;		/* number of serial tty's */
-	short		tty_map[];	/* map UART to tty number */
-};
 extern struct platform_device *atmel_default_console_device;
-extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
 
 struct atmel_uart_data {
 	short			use_dma_tx;	/* use transmit DMA? */
diff --git a/arch/arm/mach-at91/include/mach/stamp9g20.h b/arch/arm/mach-at91/include/mach/stamp9g20.h
new file mode 100644
index 000000000000..6120f9c46d59
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/stamp9g20.h
@@ -0,0 +1,7 @@
+#ifndef __MACH_STAMP9G20_H
+#define __MACH_STAMP9G20_H
+
+void stamp9g20_map_io(void);
+void stamp9g20_board_init(void);
+
+#endif