diff options
Diffstat (limited to 'arch/ppc/platforms/sandpoint.h')
| -rw-r--r-- | arch/ppc/platforms/sandpoint.h | 75 |
1 files changed, 0 insertions, 75 deletions
diff --git a/arch/ppc/platforms/sandpoint.h b/arch/ppc/platforms/sandpoint.h deleted file mode 100644 index ed83759e4044..000000000000 --- a/arch/ppc/platforms/sandpoint.h +++ /dev/null @@ -1,75 +0,0 @@ -/* - * Definitions for Motorola SPS Sandpoint Test Platform - * - * Author: Mark A. Greer - * mgreer@mvista.com - * - * 2000-2003 (c) MontaVista, Software, Inc. This file is licensed under - * the terms of the GNU General Public License version 2. This program - * is licensed "as is" without any warranty of any kind, whether express - * or implied. - */ - -/* - * Sandpoint uses the CHRP map (Map B). - */ - -#ifndef __PPC_PLATFORMS_SANDPOINT_H -#define __PPC_PLATFORMS_SANDPOINT_H - -#include <asm/ppcboot.h> - -#if 0 -/* The Sandpoint X3 allows the IDE interrupt to be directly connected - * from the Windbond (PCI INTC or INTD) to the serial EPIC. Someday - * we should try this, but it was easier to use the existing 83c553 - * initialization than change it to route the different interrupts :-). - * -- Dan - */ -#define SANDPOINT_IDE_INT0 23 /* EPIC 7 */ -#define SANDPOINT_IDE_INT1 24 /* EPIC 8 */ -#endif - -/* - * The sandpoint boards have processor modules that either have an 8240 or - * an MPC107 host bridge on them. These bridges have an IDSEL line that allows - * them to respond to PCI transactions as if they were a normal PCI devices. - * However, the processor on the processor side of the bridge can not reach - * out onto the PCI bus and then select the bridge or bad things will happen - * (documented in the 8240 and 107 manuals). - * Because of this, we always skip the bridge PCI device when accessing the - * PCI bus. The PCI slot that the bridge occupies is defined by the macro - * below. - */ -#define SANDPOINT_HOST_BRIDGE_IDSEL 12 - -/* - * Serial defines. - */ -#define SANDPOINT_SERIAL_0 0xfe0003f8 -#define SANDPOINT_SERIAL_1 0xfe0002f8 - -#define RS_TABLE_SIZE 2 - -/* Rate for the 1.8432 Mhz clock for the onboard serial chip */ -#define BASE_BAUD ( 1843200 / 16 ) -#define UART_CLK 1843200 - -#ifdef CONFIG_SERIAL_DETECT_IRQ -#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF|ASYNC_AUTO_IRQ) -#else -#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF) -#endif - -#define STD_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, SANDPOINT_SERIAL_0, 4, STD_COM_FLAGS, /* ttyS0 */ \ - iomem_base: (u8 *)SANDPOINT_SERIAL_0, \ - io_type: SERIAL_IO_MEM }, \ - { 0, BASE_BAUD, SANDPOINT_SERIAL_1, 3, STD_COM_FLAGS, /* ttyS1 */ \ - iomem_base: (u8 *)SANDPOINT_SERIAL_1, \ - io_type: SERIAL_IO_MEM }, - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DFNS - -#endif /* __PPC_PLATFORMS_SANDPOINT_H */ |