summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2010-03-24[S390] dasd: fix alignment of transport mode recovery TCWStefan Weinhuber1-3/+4
All TCWs need to be aligned on a 64 byte boundary or the I/O will be rejected. For recovery requests we create fresh TCWs, so we need to do the proper alignment here as well. Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2010-03-24[S390] zcore: CPU registers are not saved under LPARMichael Holzheu1-29/+2
To save the registers for all CPUs a sigp "store status" is done that stores the registers to address absolute zero. To access storage at absolute zero, normally the address of the prefix register of the accessing CPU has to be used. This does not work when large pages are active (currently only under LPAR). In order to fix that problem, instead of memcpy memcpy_real is used, which switches to real mode where prefixing works. Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2010-03-23drm/i915: Stop trying to use ACPI lid status to determine LVDS connection.Eric Anholt1-51/+1
I've been getting more and more quirk reports about this. It seems clear at this point that other OSes are not using this for determining whether the integrated panel should be turned on, and it is not reliable for doing so. Better to light up an unintended panel than to not light up the only usable output on the system. Signed-off-by: Eric Anholt <eric@anholt.net> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-23libata-sff: fix spurious IRQ handlingTejun Heo1-7/+36
Commit 27943620cbd960f710a385ff4a538e14ed3f1922 introduced spurious IRQ handling but it has a race condition where valid completion can be lost while trying to clear spurious IRQ leading to occassional command timeouts. This patch improves SFF interrupt handler such that 1. Once BMDMA HSM is stopped, the condition is never considered spurious. As there's no way to resume stopped BMDMA HSM, if device status doesn't agree with BMDMA status, the only way out is aborting the command (otherwise, it will just end up timing out). 2. ap->ops->sff_check_status() can be safely called to clear spurious device IRQ as it atomically returns completion status but BMDMA IRQ status can't be cleared in safe way if command is in flight. After a spurious IRQ, call ap->ops->sff_irq_clear() only if the respective device is idle and retry completion if sff_check_status() indicates command completion. Please note that ata_piix uses bmdma_status for sff_irq_check() and #2 won't weaken spurious IRQ handling even with in-flight command because if bmdma_status indicates IRQ pending but device status is not on spurious check, the next IRQ handler invocation will abort the command due to #1. This fixes bko#15537. https://bugzilla.kernel.org/show_bug.cgi?id=15537 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Andrew Benton <b3nton@gmail.com> Cc: Petr Uzel <petr.uzel@centrum.cz> Cc: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-23SH: remove superfluous warning from the serial driverGuennadi Liakhovetski1-4/+0
This warning has been introduced during the SCI DMA support developmenr and is not needed any more. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23SH: fix SCIFA SCASCR register bit definitionsGuennadi Liakhovetski1-1/+5
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23serial: sh-sci: fix SH-Mobile SH breakageMagnus Damm1-7/+22
The follwing commit breaks SH-Mobile on non-ARM platforms: "8a77b8d serial: sh-sci: Support ARM-based SH-Mobile CPUs." The commit assumed that CONFIG_ARCH_SHMOBILE only was set on ARM platforms, but it turns out that this kconfig is also set by all SH-based SoCs. Sh7724 and other older SH-Mobile SoCs are all broken without this fix. This patch converts the "defined(CONFIG_ARCH_SHMOBILE)" into one "defined()" per SoC model - similar to existing SH code. Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-22pata_via: Add VIA VX900 supportJosephChan@via.com.tw1-0/+1
Signed-off-by: Joseph Chan <josephchan@via.com.tw> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-22regulator: fix dangling pointersWolfram Sang3-3/+4
Fix I2C-drivers which missed setting clientdata to NULL before freeing the structure it points to. Also fix drivers which do this _after_ the structure was freed already. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22lp3971: Fix BUCK_VOL_CHANGE_SHIFT logicAxel Lin1-1/+1
Given x=0,1,2, current implementation of BUCK_VOL_CHANGE_SHIFT(x) returns 0,4,8. The correct return value should be 0,4,6. This patch fix the logic. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22lp3971: Fix setting val for LDO2 and LDO4Axel Lin1-1/+2
In lp3971_ldo_set_voltage function, it requires val to left shift 4 bits for LDO2 and LDO4. This patch fix this issue. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22regulator: Get rid of lockdep warningAmeya Palande1-0/+1
WARNING: at kernel/lockdep.c:2706 sysfs_add_file_mode+0x4c/0xa8() Difference between v1 and v2: Moved sysfs_attr_init() call as first one to access the structure. Signed-off-by: Ameya Palande <ameya.palande@nokia.com> CC: Liam Girdwood <lrg@slimlogic.co.uk> CC: Mark Brown <broonie@opensource.wolfsonmicro.com> CC: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22regulator: handle kcalloc() failureDan Carpenter1-0/+5
Return -ENOMEM if kcalloc() fails Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22Regulators: max8925-regulator - clean up driver data after removalDmitry Torokhov1-2/+4
It is a good tone to reset driver data after unbinding the device. Also change find_regulator_info() fro inline to __devinit - let compiler figure out if it wants it to be inlined or not. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22Merge branch 'for-linus' of ↵Linus Torvalds1-2/+13
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: virtio: console: Check if port is valid in resize_console virtio: console: Generate a kobject CHANGE event on adding 'name' attribute
2010-03-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds20-137/+229
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (38 commits) ip_gre: include route header_len in max_headroom calculation if_tunnel.h: add missing ams/byteorder.h include ipv4: Don't drop redirected route cache entry unless PTMU actually expired net: suppress lockdep-RCU false positive in FIB trie. Bluetooth: Fix kernel crash on L2CAP stress tests Bluetooth: Convert debug files to actually use debugfs instead of sysfs Bluetooth: Fix potential bad memory access with sysfs files netfilter: ctnetlink: fix reliable event delivery if message building fails netlink: fix NETLINK_RECV_NO_ENOBUFS in netlink_set_err() NET_DMA: free skbs periodically netlink: fix unaligned access in nla_get_be64() tcp: Fix tcp_mark_head_lost() with packets == 0 net: ipmr/ip6mr: fix potential out-of-bounds vif_table access KS8695: update ksp->next_rx_desc_read at the end of rx loop igb: Add support for 82576 ET2 Quad Port Server Adapter ixgbevf: Message formatting cleanups ixgbevf: Shorten up delay timer for watchdog task ixgbevf: Fix VF Stats accounting after reset ixgbe: Set IXGBE_RSC_CB(skb)->DMA field to zero after unmapping the address ixgbe: fix for real_num_tx_queues update issue ...
2010-03-22edac, mce: Filter out invalid valuesBorislav Petkov1-1/+6
Print the CPU associated with the error only when the field is valid. Cc: <stable@kernel.org> # .32.x .33.x Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2010-03-22pxa168fb: fix incorrect resource calculationDan Carpenter1-1/+1
The size calculation is not correct. It should be end - start + 1. Use resource_size() to caculate it. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2010-03-22virtio: console: Check if port is valid in resize_consoleAmit Shah1-0/+4
The console port could have been hot-unplugged. Check if it is valid before working on it. Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2010-03-22virtio: console: Generate a kobject CHANGE event on adding 'name' attributeAmit Shah1-2/+9
When the host lets us know what 'name' a port is assigned, we create the sysfs 'name' attribute. Generate a 'change' event after this so that udev wakes up and acts on the rules for virtio-ports (currently there's only one rule that creates a symlink from the 'name' to the actual char device). Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2010-03-20Merge branch 'vhost' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostDavid S. Miller2-10/+18
2010-03-19KS8695: update ksp->next_rx_desc_read at the end of rx loopYegor Yefremov1-15/+9
There is no need to adjust the next rx descriptor after each packet, so do it only once at the end of the routine. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2010-03-19igb: Add support for 82576 ET2 Quad Port Server AdapterCarolyn Wyborny3-0/+3
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-19ixgbevf: Message formatting cleanupsGreg Rose1-2/+2
Clean up some text output formatting. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-19ixgbevf: Shorten up delay timer for watchdog taskGreg Rose1-1/+1
The recovery from PF reset works better when you shorten up the delay until the watchdog task executes. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-19ixgbevf: Fix VF Stats accounting after resetGreg Rose3-38/+78
The counters in the 82599 Virtual Function are not clear on read. They accumulate to the maximum value and then roll over. They are also not cleared when the VF executes a soft reset, so it is possible they are non-zero when the driver loads and starts. This has all been accounted for in the code that keeps the stats up to date but there is one case that is not. When the PF driver is reset the counters in the VF are all reset to zero. This adds an additional accounting overhead into the VF driver when the PF is reset under its feet. This patch adds additional counters that are used by the VF driver to accumulate and save stats after a PF reset has been detected. Prior to this patch displaying the stats in the VF after the PF has reset would show bogus data. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-19ixgbe: Set IXGBE_RSC_CB(skb)->DMA field to zero after unmapping the addressMallikarjuna R Chilakala1-2/+6
As per Simon Horman's feedback set IXGBE_RSC_CB(skb)->dma to zero after unmapping HWRSC DMA address to avoid double freeing. Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-19ixgbe: fix for real_num_tx_queues update issueVasu Dev1-3/+3
Currently netdev_features_change is called before fcoe tx queues setup is done, so this patch moves calling of netdev_features_change after tx queues setup is done in ixgbe_init_interrupt_scheme, so that real_num_tx_queues is updated correctly on each fcoe enable or disable. This allows additional fcoe queues updated correctly in vlan driver for their correct queue selection. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds2-2/+30
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: serial: sh-sci: remove duplicated #include sh: Export uncached helper symbols. sh: Fix up NUMA build for 29-bit. serial: sh-sci: Fix build failure for non-sh architectures. sh: Fix up uncached offset for legacy 29-bit mode. sh: Support CPU affinity masks for INTC controllers.
2010-03-19Merge branch 'for-upstream' of ↵Linus Torvalds3-51/+69
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb * 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: uwb: remove duplicate cpu_to_le16() uwb: declare MODULE_FIRMWARE() in i1480 DFU driver uwb: make USB device id table constant uwb: wlp: refactor wlp_get_<attribute>() macros
2010-03-19Merge branch 'zerolen' of ↵Linus Torvalds1-0/+0
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6 * 'zerolen' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6: Delete zero-length file drivers/mtd/maps/omap_nor.c
2010-03-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6Linus Torvalds6-35/+46
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: tty_port,usb-console: Fix usb serial console open/close regression tty: cpm_uart: use resource_size() tty_buffer: Fix distinct type warning hvc_console: Fix race between hvc_close and hvc_remove uartlite: Fix build on sparc. tty: Take a 256 byte padding into account when buffering below sub-page units Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
2010-03-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6Linus Torvalds10-18/+62
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: driver core: numa: fix BUILD_BUG_ON for node_read_distance driver-core: document ERR_PTR() return values kobject: documentation: Update to refer to kset-example.c. sysdev: the cpu probe/release attributes should be sysdev_class_attributes kobject: documentation: Fix erroneous example in kobject doc. driver-core: fix missing kernel-doc in firmware_class Driver core: Early platform kernel-doc update sysfs: fix sysfs lockdep warning in mlx4 code sysfs: fix sysfs lockdep warning in infiniband code sysfs: fix sysfs lockdep warning in ipmi code sysfs: Initialised pci bus legacy_mem field before use sysfs: use sysfs_bin_attr_init in firmware class driver
2010-03-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds30-142/+321
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (45 commits) USB: gadget/multi: cdc_do_config: remove redundant check usb: r8a66597-hcd: fix removed from an attached hub USB: xhci: Make endpoint interval debugging clearer. USB: Fix usb_fill_int_urb for SuperSpeed devices USB: cp210x: Remove double usb_control_msg from cp210x_set_config USB: Remove last bit of CONFIG_USB_BERRY_CHARGE USB: gadget: add gadget controller number for s3c-hsotg driver USB: ftdi_sio: Fix locking for change_speed() function USB: g_mass_storage: fixed module name in Kconfig USB: gadget: f_mass_storage::fsg_bind(): fix error handling USB: g_mass_storage: fix section mismatch warnings USB: gadget: fix Blackfin builds after gadget cleansing USB: goku_udc: remove potential null dereference USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is 0xff USB: serial: Fix module name typo for qcaux Kconfig entry. usb: cdc-wdm: Fix deadlock between write and resume usb: cdc-wdm: Fix order in disconnect and fix locking usb: cdc-wdm:Fix loss of data due to autosuspend usb: cdc-wdm: Fix submission of URB after suspension usb: cdc-wdm: Fix race between disconnect and debug messages ...
2010-03-19Delete zero-length file drivers/mtd/maps/omap_nor.cJeff Garzik1-0/+0
The content was deleted in cc87edb173effdf74e680ee6d622a935ff0c1d6f, but the file remained as a zero-length file. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-19USB: gadget/multi: cdc_do_config: remove redundant checkPeter Korsgaard1-2/+0
cdc_do_config() had a double ret check after fsg_add(). Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19usb: r8a66597-hcd: fix removed from an attached hubYoshihiro Shimoda1-5/+11
fix the problem that when a USB hub is attached to the r8a66597-hcd and a device is removed from that hub, it's likely that a kernel panic follows. Reported-by: Markus Pietrek <Markus.Pietrek@emtrion.de> Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: xhci: Make endpoint interval debugging clearer.Sarah Sharp1-2/+7
The xHCI hardware can only handle polling intervals that are a power of two. When we add a new endpoint during a bandwidth allocation, and the polling interval is rounded down to a power of two, print the original polling interval in the endpoint descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: Fix usb_fill_int_urb for SuperSpeed devicesMatthew Wilcox1-0/+1
USB 3 and Wireless USB specify a logarithmic encoding of the endpoint interval that matches the USB 2 specification. usb_fill_int_urb() didn't know that and was filling in the interval as if it was USB 1.1. Fix usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case alone, because David Vrabel wants to keep the old encoding. Update the struct urb kernel doc to note that SuperSpeed URBs must have urb->interval specified in microframes. Add a missing break statement in the usb_submit_urb() interrupt URB checking, since wireless USB and SuperSpeed USB encode urb->interval differently. This allows xHCI roothubs to actually register with khubd. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: cp210x: Remove double usb_control_msg from cp210x_set_configMichael Brunner1-5/+0
This patch removes a double usb_control_msg that sets the cp210x configuration registers a second time when calling cp210x_set_config. For data sizes >2 the second write gets corrupted. The patch has been created against 2.6.34-rc1, but all cp210x driver revisions are affected. Signed-off-by: Michael Brunner <mibru@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: Remove last bit of CONFIG_USB_BERRY_CHARGEChristoph Egger1-14/+0
One last bit was missed while removing the USB_BERRY_CHARGE config option in a8d4211f33a9573f7b1bdcfd9c9c48631d1515ee which gets dropped by this patch. Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: gadget: add gadget controller number for s3c-hsotg driverMaurus Cuelenaere1-0/+8
This prevents some drivers from complaining that no bcdDevice id was set. Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: ftdi_sio: Fix locking for change_speed() functionAlessio Igor Bogani1-2/+4
The change_speed() function should be serialized against multiple calls. Use the cfg_lock mutex to do this. Signed-off-by: Alessio Igor Bogani <abogani@texware.it> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: g_mass_storage: fixed module name in KconfigMichal Nazarewicz1-1/+1
The Kconfig help message for Mass Storage Gadget claimed the module will be named "g_file_storage" whereas it should be "g_mass_storage". Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: gadget: f_mass_storage::fsg_bind(): fix error handlingPeter Korsgaard1-1/+0
Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors, which decreases refcount and frees the fsg_dev structure, causing trouble when fsg_add does the same. Fix it by simply leaving up cleanup to fsg_add(). Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: g_mass_storage: fix section mismatch warningsMike Frysinger1-1/+1
The recent commit (0e530b45783f75) that moved usb_ep_autoconfig from the __devinit section to the __init section missed the mass storage device. Its fsg_bind() function uses the usb_ep_autoconfig() function from non __init context leading to: WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in reference from the function _fsg_bind() to the function .init.text:_usb_ep_autoconfig() So move fsg_bind() into __init as well. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: gadget: fix Blackfin builds after gadget cleansingMike Frysinger1-1/+1
The recent change to clean out dead gadget drivers (90f7976880bbbf99) missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN. This causes Blackfin gadget builds to fail since the function no longer exists anywhere. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: goku_udc: remove potential null dereferenceDan Carpenter1-1/+1
"dev" is always null here. In the end it's only used to get the pci_name() of "pdev" which is redundant information and so I removed it. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is ↵spark1-0/+43
0xff Signed-off-by: spark <spark@bandrich.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: serial: Fix module name typo for qcaux Kconfig entry.Stefan Schmidt1-2/+2
The module is called qcaux and not moto_modem. Also use help instead of ---help-- to be in sync with the other Kconfig entries. Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-25 06:56:43 +0000