diff options
Diffstat (limited to 'arch/mips/au1000/pb1000/board_setup.c')
-rw-r--r-- | arch/mips/au1000/pb1000/board_setup.c | 117 |
1 files changed, 57 insertions, 60 deletions
diff --git a/arch/mips/au1000/pb1000/board_setup.c b/arch/mips/au1000/pb1000/board_setup.c index 33f15acc1b1..25df167a95b 100644 --- a/arch/mips/au1000/pb1000/board_setup.c +++ b/arch/mips/au1000/pb1000/board_setup.c @@ -1,7 +1,6 @@ /* - * Copyright 2000 MontaVista Software Inc. - * Author: MontaVista Software, Inc. - * ppopov@mvista.com or source@mvista.com + * Copyright 2000, 2008 MontaVista Software Inc. + * Author: MontaVista Software, Inc. <source@mvista.com> * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the @@ -40,128 +39,126 @@ void __init board_setup(void) u32 sys_freqctrl, sys_clksrc; u32 prid = read_c0_prid(); - // set AUX clock to 12MHz * 8 = 96 MHz + /* Set AUX clock to 12 MHz * 8 = 96 MHz */ au_writel(8, SYS_AUXPLL); au_writel(0, SYS_PINSTATERD); udelay(100); #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) - /* zero and disable FREQ2 */ + /* Zero and disable FREQ2 */ sys_freqctrl = au_readl(SYS_FREQCTRL0); sys_freqctrl &= ~0xFFF00000; au_writel(sys_freqctrl, SYS_FREQCTRL0); - /* zero and disable USBH/USBD clocks */ + /* Zero and disable USBH/USBD clocks */ sys_clksrc = au_readl(SYS_CLKSRC); - sys_clksrc &= ~0x00007FE0; + sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK | + SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK); au_writel(sys_clksrc, SYS_CLKSRC); sys_freqctrl = au_readl(SYS_FREQCTRL0); sys_freqctrl &= ~0xFFF00000; sys_clksrc = au_readl(SYS_CLKSRC); - sys_clksrc &= ~0x00007FE0; + sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK | + SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK); - switch (prid & 0x000000FF) - { + switch (prid & 0x000000FF) { case 0x00: /* DA */ case 0x01: /* HA */ case 0x02: /* HB */ - /* CPU core freq to 48MHz to slow it way down... */ - au_writel(4, SYS_CPUPLL); + /* CPU core freq to 48 MHz to slow it way down... */ + au_writel(4, SYS_CPUPLL); - /* - * Setup 48MHz FREQ2 from CPUPLL for USB Host - */ - /* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */ - sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20)); - au_writel(sys_freqctrl, SYS_FREQCTRL0); + /* + * Setup 48 MHz FREQ2 from CPUPLL for USB Host + * FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz + */ + sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2; + au_writel(sys_freqctrl, SYS_FREQCTRL0); - /* CPU core freq to 384MHz */ - au_writel(0x20, SYS_CPUPLL); + /* CPU core freq to 384 MHz */ + au_writel(0x20, SYS_CPUPLL); - printk("Au1000: 48MHz OHCI workaround enabled\n"); + printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n"); break; - default: /* HC and newer */ - // FREQ2 = aux/2 = 48 MHz - sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20)); - au_writel(sys_freqctrl, SYS_FREQCTRL0); + default: /* HC and newer */ + /* FREQ2 = aux / 2 = 48 MHz */ + sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | + SYS_FC_FE2 | SYS_FC_FS2; + au_writel(sys_freqctrl, SYS_FREQCTRL0); break; } /* - * Route 48MHz FREQ2 into USB Host and/or Device + * Route 48 MHz FREQ2 into USB Host and/or Device */ -#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) - sys_clksrc |= ((4<<12) | (0<<11) | (0<<10)); -#endif + sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT; au_writel(sys_clksrc, SYS_CLKSRC); - // configure pins GPIO[14:9] as GPIO - pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8080); + /* Configure pins GPIO[14:9] as GPIO */ + pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB); - // 2nd USB port is USB host - pin_func |= 0x8000; + /* 2nd USB port is USB host */ + pin_func |= SYS_PF_USB; au_writel(pin_func, SYS_PINFUNC); au_writel(0x2800, SYS_TRIOUTCLR); au_writel(0x0030, SYS_OUTPUTCLR); #endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */ - // make gpio 15 an input (for interrupt line) - pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x100); - // we don't need I2S, so make it available for GPIO[31:29] - pin_func |= (1<<5); + /* Make GPIO 15 an input (for interrupt line) */ + pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF; + /* We don't need I2S, so make it available for GPIO[31:29] */ + pin_func |= SYS_PF_I2S; au_writel(pin_func, SYS_PINFUNC); au_writel(0x8000, SYS_TRIOUTCLR); - static_cfg0 = au_readl(MEM_STCFG0) & (u32)(~0xc00); + static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00; au_writel(static_cfg0, MEM_STCFG0); - // configure RCE2* for LCD + /* configure RCE2* for LCD */ au_writel(0x00000004, MEM_STCFG2); - // MEM_STTIME2 + /* MEM_STTIME2 */ au_writel(0x09000000, MEM_STTIME2); - // Set 32-bit base address decoding for RCE2* + /* Set 32-bit base address decoding for RCE2* */ au_writel(0x10003ff0, MEM_STADDR2); - // PCI CPLD setup - // expand CE0 to cover PCI + /* + * PCI CPLD setup + * Expand CE0 to cover PCI + */ au_writel(0x11803e40, MEM_STADDR1); - // burst visibility on + /* Burst visibility on */ au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0); - au_writel(0x83, MEM_STCFG1); // ewait enabled, flash timing - au_writel(0x33030a10, MEM_STTIME1); // slower timing for FPGA + au_writel(0x83, MEM_STCFG1); /* ewait enabled, flash timing */ + au_writel(0x33030a10, MEM_STTIME1); /* slower timing for FPGA */ - /* setup the static bus controller */ + /* Setup the static bus controller */ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */ -#ifdef CONFIG_PCI - au_writel(0, PCI_BRIDGE_CONFIG); // set extend byte to 0 - au_writel(0, SDRAM_MBAR); // set mbar to 0 - au_writel(0x2, SDRAM_CMD); // enable memory accesses - au_sync_delay(1); -#endif - - /* Enable Au1000 BCLK switching - note: sed1356 must not use - * its BCLK (Au1000 LCLK) for any timings */ - switch (prid & 0x000000FF) - { + /* + * Enable Au1000 BCLK switching - note: sed1356 must not use + * its BCLK (Au1000 LCLK) for any timings + */ + switch (prid & 0x000000FF) { case 0x00: /* DA */ case 0x01: /* HA */ case 0x02: /* HB */ break; default: /* HC and newer */ - /* Enable sys bus clock divider when IDLE state or no bus - activity. */ + /* + * Enable sys bus clock divider when IDLE state or no bus + * activity. + */ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL); break; } |