| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Zefan Li requested [1] to perform the following cleanup/refactoring:
- Split cgroupfs classid handling into net core to better express a
possible more generic use.
- Disable module support for cgroupfs bits as the majority of other
cgroupfs subsystems do not have that, and seems to be not wished
from cgroup side. Zefan probably might want to follow-up for netprio
later on.
- By this, code can be further reduced which previously took care of
functionality built when compiled as module.
cgroupfs bits are being placed under net/core/netclassid_cgroup.c, so
that we are consistent with {netclassid,netprio}_cgroup naming that is
under net/core/ as suggested by Zefan.
No change in functionality, but only code refactoring that is being
done here.
[1] http://patchwork.ozlabs.org/patch/304825/
Suggested-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
|
|
The names of the two struct cgroup_subsys_state accessors -
cgroup_subsys_state() and task_subsys_state() - are somewhat awkward.
The former clashes with the type name and the latter doesn't even
indicate it's somehow related to cgroup.
We're about to revamp large portion of cgroup API, so, let's rename
them so that they're less awkward. Most per-controller usages of the
accessors are localized in accessor wrappers and given the amount of
scheduled changes, this isn't gonna add any noticeable headache.
Rename cgroup_subsys_state() to cgroup_css() and task_subsys_state()
to task_css(). This patch is pure rename.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The callers always pass current to sock_update_classid().
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the real implementation got updated.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sock_update_classid() assumes that the update operation always are
applied on the current task. sock_update_classid() needs to know on
which tasks to work on in order to be able to migrate task between
cgroups using the struct cgroup_subsys attach() callback.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Joe Perches <joe@perches.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <netdev@vger.kernel.org>
Cc: <cgroups@vger.kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The classid type used throughout the kernel is u32.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <netdev@vger.kernel.org>
Cc: <cgroups@vger.kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARNING: With this change it is impossible to load external built
controllers anymore.
In case where CONFIG_NETPRIO_CGROUP=m and CONFIG_NET_CLS_CGROUP=m is
set, corresponding subsys_id should also be a constant. Up to now,
net_prio_subsys_id and net_cls_subsys_id would be of the type int and
the value would be assigned during runtime.
By switching the macro definition IS_SUBSYS_ENABLED from IS_BUILTIN
to IS_ENABLED, all *_subsys_id will have constant value. That means we
need to remove all the code which assumes a value can be assigned to
net_prio_subsys_id and net_cls_subsys_id.
A close look is necessary on the RCU part which was introduces by
following patch:
commit f845172531fb7410c7fb7780b1a6e51ee6df7d52
Author: Herbert Xu <herbert@gondor.apana.org.au> Mon May 24 09:12:34 2010
Committer: David S. Miller <davem@davemloft.net> Mon May 24 09:12:34 2010
cls_cgroup: Store classid in struct sock
Tis code was added to init_cgroup_cls()
/* We can't use rcu_assign_pointer because this is an int. */
smp_wmb();
net_cls_subsys_id = net_cls_subsys.subsys_id;
respectively to exit_cgroup_cls()
net_cls_subsys_id = -1;
synchronize_rcu();
and in module version of task_cls_classid()
rcu_read_lock();
id = rcu_dereference(net_cls_subsys_id);
if (id >= 0)
classid = container_of(task_subsys_state(p, id),
struct cgroup_cls_state, css)->classid;
rcu_read_unlock();
Without an explicit explaination why the RCU part is needed. (The
rcu_deference was fixed by exchanging it to rcu_derefence_index_check()
in a later commit, but that is a minor detail.)
So here is my pondering why it was introduced and why it safe to
remove it now. Note that this code was copied over to net_prio the
reasoning holds for that subsystem too.
The idea behind the RCU use for net_cls_subsys_id is to make sure we
get a valid pointer back from task_subsys_state(). task_subsys_state()
is just blindly accessing the subsys array and returning the
pointer. Obviously, passing in -1 as id into task_subsys_state()
returns an invalid value (out of lower bound).
So this code makes sure that only after module is loaded and the
subsystem registered, the id is assigned.
Before unregistering the module all old readers must have left the
critical section. This is done by assigning -1 to the id and issuing a
synchronized_rcu(). Any new readers wont call task_subsys_state()
anymore and therefore it is safe to unregister the subsystem.
The new code relies on the same trick, but it looks at the subsys
pointer return by task_subsys_state() (remember the id is constant
and therefore we allways have a valid index into the subsys
array).
No precautions need to be taken during module loading
module. Eventually, all CPUs will get a valid pointer back from
task_subsys_state() because rebind_subsystem() which is called after
the module init() function will assigned subsys[net_cls_subsys_id] the
newly loaded module subsystem pointer.
When the subsystem is about to be removed, rebind_subsystem() will
called before the module exit() function. In this case,
rebind_subsys() will assign subsys[net_cls_subsys_id] a NULL pointer
and then it calls synchronize_rcu(). All old readers have left by then
the critical section. Any new reader wont access the subsystem
anymore. At this point we are safe to unregister the subsystem. No
synchronize_rcu() call is needed.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
|
|
task_cls_classid() should not be defined in case the configuration is
CONFIG_NET_CLS_CGROUP=n. The reason is that in a following patch the
net_cls_subsys_id will only be defined if CONFIG_NET_CLS_CGROUP!=n.
When net_cls is not built at all a callee should only get an empty
task_cls_classid() without any references to net_cls_subsys_id.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
|
|
The only user of sock_update_classid() is net/socket.c which happens
to include cls_cgroup.h directly.
tj: Fix build breakage due to missing cls_cgroup.h inclusion in
drivers/net/tun.c reported in linux-next by Stephen.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
|
|
Merge reason: Update from -rc3 to -rc7.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Dave reported an rcu lockdep warning on 2.6.35.4 kernel
task->cgroups and task->cgroups->subsys[i] are protected by RCU.
So we avoid accessing invalid pointers here. This might happen,
for example, when you are deref-ing those pointers while someone
move @task from one cgroup to another.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The task_cls_classid() function applies rcu_dereference() to integers,
which does not work with the shiny new sparse-based checking in
rcu_dereference(). This commit therefore moves to the new RCU API
rcu_dereference_index_check().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the cls_cgroup module is not loaded, task_cls_classid will
return an uninitialised classid instead of zero.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a typo in cgroup_cls_state when cls_cgroup is built-in.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now cls_cgroup has relied on fetching the classid out of
the current executing thread. This runs into trouble when a packet
processing is delayed in which case it may execute out of another
thread's context.
Furthermore, even when a packet is not delayed we may fail to
classify it if soft IRQs have been disabled, because this scenario
is indistinguishable from one where a packet unrelated to the
current thread is processed by a real soft IRQ.
In fact, the current semantics is inherently broken, as a single
skb may be constructed out of the writes of two different tasks.
A different manifestation of this problem is when the TCP stack
transmits in response of an incoming ACK. This is currently
unclassified.
As we already have a concept of packet ownership for accounting
purposes in the skb->sk pointer, this is a natural place to store
the classid in a persistent manner.
This patch adds the cls_cgroup classid in struct sock, filling up
an existing hole on 64-bit :)
The value is set at socket creation time. So all sockets created
via socket(2) automatically gains the ID of the thread creating it.
Whenever another process touches the socket by either reading or
writing to it, we will change the socket classid to that of the
process if it has a valid (non-zero) classid.
For sockets created on inbound connections through accept(2), we
inherit the classid of the original listening socket through
sk_clone, possibly preceding the actual accept(2) call.
In order to minimise risks, I have not made this the authoritative
classid. For now it is only used as a backup when we execute
with soft IRQs disabled. Once we're completely happy with its
semantics we can use it as the sole classid.
Footnote: I have rearranged the error path on cls_group module
creation. If we didn't do this, then there is a window where
someone could create a tc rule using cls_group before the cgroup
subsystem has been registered.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
