From 8887ca5474bd9ddb56cabc88856bb035774e0041 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 20 Jul 2021 14:33:49 +0100 Subject: net: phy: at803x: simplify custom phy id matching The at803x driver contains a function, at803x_match_phy_id(), which tests whether the PHY ID matches the value passed, comparing phy_id with phydev->phy_id and testing all bits that in the driver's mask. This is the same test that is used to match the driver, with phy_id replaced with the driver specified ID, phydev->drv->phy_id. Hence, we already know the value of the bits being tested if we look at phydev->drv->phy_id directly, and we do not require a complicated test to check them. Test directly against phydev->drv->phy_id instead. Signed-off-by: Russell King Reviewed-by: Fabio Estevam Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- drivers/net/phy/at803x.c | 16 +++++----------- 1 file changed, 5 insertions(+), 11 deletions(-) (limited to 'drivers/net/phy') diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 5d62b85a4024..0790ffcd3db6 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -532,12 +532,6 @@ static int at8031_register_regulators(struct phy_device *phydev) return 0; } -static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id) -{ - return (phydev->phy_id & phydev->drv->phy_id_mask) - == (phy_id & phydev->drv->phy_id_mask); -} - static int at803x_parse_dt(struct phy_device *phydev) { struct device_node *node = phydev->mdio.dev.of_node; @@ -602,8 +596,8 @@ static int at803x_parse_dt(struct phy_device *phydev) * to the AR8030 so there might be a good chance it works on * the AR8030 too. */ - if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) || - at803x_match_phy_id(phydev, ATH8035_PHY_ID)) { + if (phydev->drv->phy_id == ATH8030_PHY_ID || + phydev->drv->phy_id == ATH8035_PHY_ID) { priv->clk_25m_reg &= AT8035_CLK_OUT_MASK; priv->clk_25m_mask &= AT8035_CLK_OUT_MASK; } @@ -631,7 +625,7 @@ static int at803x_parse_dt(struct phy_device *phydev) /* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping * options. */ - if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + if (phydev->drv->phy_id == ATH8031_PHY_ID) { if (of_property_read_bool(node, "qca,keep-pll-enabled")) priv->flags |= AT803X_KEEP_PLL_ENABLED; @@ -676,7 +670,7 @@ static int at803x_probe(struct phy_device *phydev) * Switch to the copper page, as otherwise we read * the PHY capabilities from the fiber side. */ - if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + if (phydev->drv->phy_id == ATH8031_PHY_ID) { phy_lock_mdio_bus(phydev); ret = at803x_write_page(phydev, AT803X_PAGE_COPPER); phy_unlock_mdio_bus(phydev); @@ -820,7 +814,7 @@ static int at803x_config_init(struct phy_device *phydev) if (ret < 0) return ret; - if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + if (phydev->drv->phy_id == ATH8031_PHY_ID) { ret = at8031_pll_config(phydev); if (ret < 0) return ret; -- cgit v1.2.3