From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- Documentation/i2c/busses/i2c-ali1535 | 42 ++++++++ Documentation/i2c/busses/i2c-ali1563 | 27 +++++ Documentation/i2c/busses/i2c-ali15x3 | 112 +++++++++++++++++++++ Documentation/i2c/busses/i2c-amd756 | 25 +++++ Documentation/i2c/busses/i2c-amd8111 | 41 ++++++++ Documentation/i2c/busses/i2c-i801 | 80 +++++++++++++++ Documentation/i2c/busses/i2c-i810 | 46 +++++++++ Documentation/i2c/busses/i2c-nforce2 | 41 ++++++++ Documentation/i2c/busses/i2c-parport | 154 +++++++++++++++++++++++++++++ Documentation/i2c/busses/i2c-parport-light | 11 +++ Documentation/i2c/busses/i2c-pca-isa | 23 +++++ Documentation/i2c/busses/i2c-piix4 | 72 ++++++++++++++ Documentation/i2c/busses/i2c-prosavage | 23 +++++ Documentation/i2c/busses/i2c-savage4 | 26 +++++ Documentation/i2c/busses/i2c-sis5595 | 59 +++++++++++ Documentation/i2c/busses/i2c-sis630 | 49 +++++++++ Documentation/i2c/busses/i2c-sis69x | 73 ++++++++++++++ Documentation/i2c/busses/i2c-via | 34 +++++++ Documentation/i2c/busses/i2c-viapro | 47 +++++++++ Documentation/i2c/busses/i2c-voodoo3 | 62 ++++++++++++ Documentation/i2c/busses/scx200_acb | 14 +++ 21 files changed, 1061 insertions(+) create mode 100644 Documentation/i2c/busses/i2c-ali1535 create mode 100644 Documentation/i2c/busses/i2c-ali1563 create mode 100644 Documentation/i2c/busses/i2c-ali15x3 create mode 100644 Documentation/i2c/busses/i2c-amd756 create mode 100644 Documentation/i2c/busses/i2c-amd8111 create mode 100644 Documentation/i2c/busses/i2c-i801 create mode 100644 Documentation/i2c/busses/i2c-i810 create mode 100644 Documentation/i2c/busses/i2c-nforce2 create mode 100644 Documentation/i2c/busses/i2c-parport create mode 100644 Documentation/i2c/busses/i2c-parport-light create mode 100644 Documentation/i2c/busses/i2c-pca-isa create mode 100644 Documentation/i2c/busses/i2c-piix4 create mode 100644 Documentation/i2c/busses/i2c-prosavage create mode 100644 Documentation/i2c/busses/i2c-savage4 create mode 100644 Documentation/i2c/busses/i2c-sis5595 create mode 100644 Documentation/i2c/busses/i2c-sis630 create mode 100644 Documentation/i2c/busses/i2c-sis69x create mode 100644 Documentation/i2c/busses/i2c-via create mode 100644 Documentation/i2c/busses/i2c-viapro create mode 100644 Documentation/i2c/busses/i2c-voodoo3 create mode 100644 Documentation/i2c/busses/scx200_acb (limited to 'Documentation/i2c/busses') diff --git a/Documentation/i2c/busses/i2c-ali1535 b/Documentation/i2c/busses/i2c-ali1535 new file mode 100644 index 000000000000..0db3b4c74ad1 --- /dev/null +++ b/Documentation/i2c/busses/i2c-ali1535 @@ -0,0 +1,42 @@ +Kernel driver i2c-ali1535 + +Supported adapters: + * Acer Labs, Inc. ALI 1535 (south bridge) + Datasheet: Now under NDA + http://www.ali.com.tw/eng/support/datasheet_request.php + +Authors: + Frodo Looijaard , + Philip Edelbrock , + Mark D. Studebaker , + Dan Eaton , + Stephen Rousset + +Description +----------- + +This is the driver for the SMB Host controller on Acer Labs Inc. (ALI) +M1535 South Bridge. + +The M1535 is a South bridge for portable systems. It is very similar to the +M15x3 South bridges also produced by Acer Labs Inc. Some of the registers +within the part have moved and some have been redefined slightly. +Additionally, the sequencing of the SMBus transactions has been modified to +be more consistent with the sequencing recommended by the manufacturer and +observed through testing. These changes are reflected in this driver and +can be identified by comparing this driver to the i2c-ali15x3 driver. For +an overview of these chips see http://www.acerlabs.com + +The SMB controller is part of the M7101 device, which is an ACPI-compliant +Power Management Unit (PMU). + +The whole M7101 device has to be enabled for the SMB to work. You can't +just enable the SMB alone. The SMB and the ACPI have separate I/O spaces. +We make sure that the SMB is enabled. We leave the ACPI alone. + + +Features +-------- + +This driver controls the SMB Host only. This driver does not use +interrupts. diff --git a/Documentation/i2c/busses/i2c-ali1563 b/Documentation/i2c/busses/i2c-ali1563 new file mode 100644 index 000000000000..99ad4b9bcc32 --- /dev/null +++ b/Documentation/i2c/busses/i2c-ali1563 @@ -0,0 +1,27 @@ +Kernel driver i2c-ali1563 + +Supported adapters: + * Acer Labs, Inc. ALI 1563 (south bridge) + Datasheet: Now under NDA + http://www.ali.com.tw/eng/support/datasheet_request.php + +Author: Patrick Mochel + +Description +----------- + +This is the driver for the SMB Host controller on Acer Labs Inc. (ALI) +M1563 South Bridge. + +For an overview of these chips see http://www.acerlabs.com + +The M1563 southbridge is deceptively similar to the M1533, with a few +notable exceptions. One of those happens to be the fact they upgraded the +i2c core to be SMBus 2.0 compliant, and happens to be almost identical to +the i2c controller found in the Intel 801 south bridges. + +Features +-------- + +This driver controls the SMB Host only. This driver does not use +interrupts. diff --git a/Documentation/i2c/busses/i2c-ali15x3 b/Documentation/i2c/busses/i2c-ali15x3 new file mode 100644 index 000000000000..ff28d381bebe --- /dev/null +++ b/Documentation/i2c/busses/i2c-ali15x3 @@ -0,0 +1,112 @@ +Kernel driver i2c-ali15x3 + +Supported adapters: + * Acer Labs, Inc. ALI 1533 and 1543C (south bridge) + Datasheet: Now under NDA + http://www.ali.com.tw/eng/support/datasheet_request.php + +Authors: + Frodo Looijaard , + Philip Edelbrock , + Mark D. Studebaker + +Module Parameters +----------------- + +* force_addr: int + Initialize the base address of the i2c controller + + +Notes +----- + +The force_addr parameter is useful for boards that don't set the address in +the BIOS. Does not do a PCI force; the device must still be present in +lspci. Don't use this unless the driver complains that the base address is +not set. + +Example: 'modprobe i2c-ali15x3 force_addr=0xe800' + +SMBus periodically hangs on ASUS P5A motherboards and can only be cleared +by a power cycle. Cause unknown (see Issues below). + + +Description +----------- + +This is the driver for the SMB Host controller on Acer Labs Inc. (ALI) +M1541 and M1543C South Bridges. + +The M1543C is a South bridge for desktop systems. +The M1541 is a South bridge for portable systems. +They are part of the following ALI chipsets: + + * "Aladdin Pro 2" includes the M1621 Slot 1 North bridge with AGP and + 100MHz CPU Front Side bus + * "Aladdin V" includes the M1541 Socket 7 North bridge with AGP and 100MHz + CPU Front Side bus + Some Aladdin V motherboards: + Asus P5A + Atrend ATC-5220 + BCM/GVC VP1541 + Biostar M5ALA + Gigabyte GA-5AX (** Generally doesn't work because the BIOS doesn't + enable the 7101 device! **) + Iwill XA100 Plus + Micronics C200 + Microstar (MSI) MS-5169 + + * "Aladdin IV" includes the M1541 Socket 7 North bridge + with host bus up to 83.3 MHz. + +For an overview of these chips see http://www.acerlabs.com. At this time the +full data sheets on the web site are password protected, however if you +contact the ALI office in San Jose they may give you the password. + +The M1533/M1543C devices appear as FOUR separate devices on the PCI bus. An +output of lspci will show something similar to the following: + + 00:02.0 USB Controller: Acer Laboratories Inc. M5237 (rev 03) + 00:03.0 Bridge: Acer Laboratories Inc. M7101 <= THIS IS THE ONE WE NEED + 00:07.0 ISA bridge: Acer Laboratories Inc. M1533 (rev c3) + 00:0f.0 IDE interface: Acer Laboratories Inc. M5229 (rev c1) + +** IMPORTANT ** +** If you have a M1533 or M1543C on the board and you get +** "ali15x3: Error: Can't detect ali15x3!" +** then run lspci. +** If you see the 1533 and 5229 devices but NOT the 7101 device, +** then you must enable ACPI, the PMU, SMB, or something similar +** in the BIOS. +** The driver won't work if it can't find the M7101 device. + +The SMB controller is part of the M7101 device, which is an ACPI-compliant +Power Management Unit (PMU). + +The whole M7101 device has to be enabled for the SMB to work. You can't +just enable the SMB alone. The SMB and the ACPI have separate I/O spaces. +We make sure that the SMB is enabled. We leave the ACPI alone. + +Features +-------- + +This driver controls the SMB Host only. The SMB Slave +controller on the M15X3 is not enabled. This driver does not use +interrupts. + + +Issues +------ + +This driver requests the I/O space for only the SMB +registers. It doesn't use the ACPI region. + +On the ASUS P5A motherboard, there are several reports that +the SMBus will hang and this can only be resolved by +powering off the computer. It appears to be worse when the board +gets hot, for example under heavy CPU load, or in the summer. +There may be electrical problems on this board. +On the P5A, the W83781D sensor chip is on both the ISA and +SMBus. Therefore the SMBus hangs can generally be avoided +by accessing the W83781D on the ISA bus only. + diff --git a/Documentation/i2c/busses/i2c-amd756 b/Documentation/i2c/busses/i2c-amd756 new file mode 100644 index 000000000000..67f30874d0bf --- /dev/null +++ b/Documentation/i2c/busses/i2c-amd756 @@ -0,0 +1,25 @@ +Kernel driver i2c-amd756 + +Supported adapters: + * AMD 756 + * AMD 766 + * AMD 768 + * AMD 8111 + Datasheets: Publicly available on AMD website + + * nVidia nForce + Datasheet: Unavailable + +Authors: + Frodo Looijaard , + Philip Edelbrock + +Description +----------- + +This driver supports the AMD 756, 766, 768 and 8111 Peripheral Bus +Controllers, and the nVidia nForce. + +Note that for the 8111, there are two SMBus adapters. The SMBus 1.0 adapter +is supported by this driver, and the SMBus 2.0 adapter is supported by the +i2c-amd8111 driver. diff --git a/Documentation/i2c/busses/i2c-amd8111 b/Documentation/i2c/busses/i2c-amd8111 new file mode 100644 index 000000000000..db294ee7455a --- /dev/null +++ b/Documentation/i2c/busses/i2c-amd8111 @@ -0,0 +1,41 @@ +Kernel driver i2c-adm8111 + +Supported adapters: + * AMD-8111 SMBus 2.0 PCI interface + +Datasheets: + AMD datasheet not yet available, but almost everything can be found + in publically available ACPI 2.0 specification, which the adapter + follows. + +Author: Vojtech Pavlik + +Description +----------- + +If you see something like this: + +00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02) + Subsystem: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 + Flags: medium devsel, IRQ 19 + I/O ports at d400 [size=32] + +in your 'lspci -v', then this driver is for your chipset. + +Process Call Support +-------------------- + +Supported. + +SMBus 2.0 Support +----------------- + +Supported. Both PEC and block process call support is implemented. Slave +mode or host notification are not yet implemented. + +Notes +----- + +Note that for the 8111, there are two SMBus adapters. The SMBus 2.0 adapter +is supported by this driver, and the SMBus 1.0 adapter is supported by the +i2c-amd756 driver. diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 new file mode 100644 index 000000000000..fd4b2712d570 --- /dev/null +++ b/Documentation/i2c/busses/i2c-i801 @@ -0,0 +1,80 @@ +Kernel driver i2c-i801 + +Supported adapters: + * Intel 82801AA and 82801AB (ICH and ICH0 - part of the + '810' and '810E' chipsets) + * Intel 82801BA (ICH2 - part of the '815E' chipset) + * Intel 82801CA/CAM (ICH3) + * Intel 82801DB (ICH4) (HW PEC supported, 32 byte buffer not supported) + * Intel 82801EB/ER (ICH5) (HW PEC supported, 32 byte buffer not supported) + * Intel 6300ESB + * Intel 82801FB/FR/FW/FRW (ICH6) + * Intel ICH7 + Datasheets: Publicly available at the Intel website + +Authors: + Frodo Looijaard , + Philip Edelbrock , + Mark Studebaker + + +Module Parameters +----------------- + +* force_addr: int + Forcibly enable the ICH at the given address. EXTREMELY DANGEROUS! + + +Description +----------- + +The ICH (properly known as the 82801AA), ICH0 (82801AB), ICH2 (82801BA), +ICH3 (82801CA/CAM) and later devices are Intel chips that are a part of +Intel's '810' chipset for Celeron-based PCs, '810E' chipset for +Pentium-based PCs, '815E' chipset, and others. + +The ICH chips contain at least SEVEN separate PCI functions in TWO logical +PCI devices. An output of lspci will show something similar to the +following: + + 00:1e.0 PCI bridge: Intel Corporation: Unknown device 2418 (rev 01) + 00:1f.0 ISA bridge: Intel Corporation: Unknown device 2410 (rev 01) + 00:1f.1 IDE interface: Intel Corporation: Unknown device 2411 (rev 01) + 00:1f.2 USB Controller: Intel Corporation: Unknown device 2412 (rev 01) + 00:1f.3 Unknown class [0c05]: Intel Corporation: Unknown device 2413 (rev 01) + +The SMBus controller is function 3 in device 1f. Class 0c05 is SMBus Serial +Controller. + +If you do NOT see the 24x3 device at function 3, and you can't figure out +any way in the BIOS to enable it, + +The ICH chips are quite similar to Intel's PIIX4 chip, at least in the +SMBus controller. + +See the file i2c-piix4 for some additional information. + + +Process Call Support +-------------------- + +Not supported. + + +I2C Block Read Support +---------------------- + +Not supported at the moment. + + +SMBus 2.0 Support +----------------- + +The 82801DB (ICH4) and later chips support several SMBus 2.0 features. + +********************** +The lm_sensors project gratefully acknowledges the support of Texas +Instruments in the initial development of this driver. + +The lm_sensors project gratefully acknowledges the support of Intel in the +development of SMBus 2.0 / ICH4 features of this driver. diff --git a/Documentation/i2c/busses/i2c-i810 b/Documentation/i2c/busses/i2c-i810 new file mode 100644 index 000000000000..0544eb332887 --- /dev/null +++ b/Documentation/i2c/busses/i2c-i810 @@ -0,0 +1,46 @@ +Kernel driver i2c-i810 + +Supported adapters: + * Intel 82810, 82810-DC100, 82810E, and 82815 (GMCH) + +Authors: + Frodo Looijaard , + Philip Edelbrock , + Kyösti Mälkki , + Ralph Metzler , + Mark D. Studebaker + +Main contact: Mark Studebaker + +Description +----------- + +WARNING: If you have an '810' or '815' motherboard, your standard I2C +temperature sensors are most likely on the 801's I2C bus. You want the +i2c-i801 driver for those, not this driver. + +Now for the i2c-i810... + +The GMCH chip contains two I2C interfaces. + +The first interface is used for DDC (Data Display Channel) which is a +serial channel through the VGA monitor connector to a DDC-compliant +monitor. This interface is defined by the Video Electronics Standards +Association (VESA). The standards are available for purchase at +http://www.vesa.org . + +The second interface is a general-purpose I2C bus. It may be connected to a +TV-out chip such as the BT869 or possibly to a digital flat-panel display. + +Features +-------- + +Both busses use the i2c-algo-bit driver for 'bit banging' +and support for specific transactions is provided by i2c-algo-bit. + +Issues +------ + +If you enable bus testing in i2c-algo-bit (insmod i2c-algo-bit bit_test=1), +the test may fail; if so, the i2c-i810 driver won't be inserted. However, +we think this has been fixed. diff --git a/Documentation/i2c/busses/i2c-nforce2 b/Documentation/i2c/busses/i2c-nforce2 new file mode 100644 index 000000000000..e379e182e64f --- /dev/null +++ b/Documentation/i2c/busses/i2c-nforce2 @@ -0,0 +1,41 @@ +Kernel driver i2c-nforce2 + +Supported adapters: + * nForce2 MCP 10de:0064 + * nForce2 Ultra 400 MCP 10de:0084 + * nForce3 Pro150 MCP 10de:00D4 + * nForce3 250Gb MCP 10de:00E4 + * nForce4 MCP 10de:0052 + +Datasheet: not publically available, but seems to be similar to the + AMD-8111 SMBus 2.0 adapter. + +Authors: + Hans-Frieder Vogt , + Thomas Leibold , + Patrick Dreker + +Description +----------- + +i2c-nforce2 is a driver for the SMBuses included in the nVidia nForce2 MCP. + +If your 'lspci -v' listing shows something like the following, + +00:01.1 SMBus: nVidia Corporation: Unknown device 0064 (rev a2) + Subsystem: Asustek Computer, Inc.: Unknown device 0c11 + Flags: 66Mhz, fast devsel, IRQ 5 + I/O ports at c000 [size=32] + Capabilities: + +then this driver should support the SMBuses of your motherboard. + + +Notes +----- + +The SMBus adapter in the nForce2 chipset seems to be very similar to the +SMBus 2.0 adapter in the AMD-8111 southbridge. However, I could only get +the driver to work with direct I/O access, which is different to the EC +interface of the AMD-8111. Tested on Asus A7N8X. The ACPI DSDT table of the +Asus A7N8X lists two SMBuses, both of which are supported by this driver. diff --git a/Documentation/i2c/busses/i2c-parport b/Documentation/i2c/busses/i2c-parport new file mode 100644 index 000000000000..9f1d0082da18 --- /dev/null +++ b/Documentation/i2c/busses/i2c-parport @@ -0,0 +1,154 @@ +Kernel driver i2c-parport + +Author: Jean Delvare + +This is a unified driver for several i2c-over-parallel-port adapters, +such as the ones made by Philips, Velleman or ELV. This driver is +meant as a replacement for the older, individual drivers: + * i2c-philips-par + * i2c-elv + * i2c-velleman + * video/i2c-parport (NOT the same as this one, dedicated to home brew + teletext adapters) + +It currently supports the following devices: + * Philips adapter + * home brew teletext adapter + * Velleman K8000 adapter + * ELV adapter + * Analog Devices evaluation boards (ADM1025, ADM1030, ADM1031, ADM1032) + +These devices use different pinout configurations, so you have to tell +the driver what you have, using the type module parameter. There is no +way to autodetect the devices. Support for different pinout configurations +can be easily added when needed. + + +Building your own adapter +------------------------- + +If you want to build you own i2c-over-parallel-port adapter, here is +a sample electronics schema (credits go to Sylvain Munaut): + +Device PC +Side ___________________Vdd (+) Side + | | | + --- --- --- + | | | | | | + |R| |R| |R| + | | | | | | + --- --- --- + | | | + | | /| | +SCL ----------x--------o |-----------x------------------- pin 2 + | \| | | + | | | + | |\ | | +SDA ----------x----x---| o---x--------------------------- pin 13 + | |/ | + | | + | /| | + ---------o |----------------x-------------- pin 3 + \| | | + | | + --- --- + | | | | + |R| |R| + | | | | + --- --- + | | + ### ### + GND GND + +Remarks: + - This is the exact pinout and electronics used on the Analog Devices + evaluation boards. + /| + - All inverters -o |- must be 74HC05, they must be open collector output. + \| + - All resitors are 10k. + - Pins 18-25 of the parallel port connected to GND. + - Pins 4-9 (D2-D7) could be used as VDD is the driver drives them high. + The ADM1032 evaluation board uses D4-D7. Beware that the amount of + current you can draw from the parallel port is limited. Also note that + all connected lines MUST BE driven at the same state, else you'll short + circuit the output buffers! So plugging the I2C adapter after loading + the i2c-parport module might be a good safety since data line state + prior to init may be unknown. + - This is 5V! + - Obviously you cannot read SCL (so it's not really standard-compliant). + Pretty easy to add, just copy the SDA part and use another input pin. + That would give (ELV compatible pinout): + + +Device PC +Side ______________________________Vdd (+) Side + | | | | + --- --- --- --- + | | | | | | | | + |R| |R| |R| |R| + | | | | | | | | + --- --- --- --- + | | | | + | | |\ | | +SCL ----------x--------x--| o---x------------------------ pin 15 + | | |/ | + | | | + | | /| | + | ---o |-------------x-------------- pin 2 + | \| | | + | | | + | | | + | |\ | | +SDA ---------------x---x--| o--------x------------------- pin 10 + | |/ | + | | + | /| | + ---o |------------------x--------- pin 3 + \| | | + | | + --- --- + | | | | + |R| |R| + | | | | + --- --- + | | + ### ### + GND GND + + +If possible, you should use the same pinout configuration as existing +adapters do, so you won't even have to change the code. + + +Similar (but different) drivers +------------------------------- + +This driver is NOT the same as the i2c-pport driver found in the i2c +package. The i2c-pport driver makes use of modern parallel port features so +that you don't need additional electronics. It has other restrictions +however, and was not ported to Linux 2.6 (yet). + +This driver is also NOT the same as the i2c-pcf-epp driver found in the +lm_sensors package. The i2c-pcf-epp driver doesn't use the parallel port as +an I2C bus directly. Instead, it uses it to control an external I2C bus +master. That driver was not ported to Linux 2.6 (yet) either. + + +Legacy documentation for Velleman adapter +----------------------------------------- + +Useful links: +Velleman http://www.velleman.be/ +Velleman K8000 Howto http://howto.htlw16.ac.at/k8000-howto.html + +The project has lead to new libs for the Velleman K8000 and K8005: + LIBK8000 v1.99.1 and LIBK8005 v0.21 +With these libs, you can control the K8000 interface card and the K8005 +stepper motor card with the simple commands which are in the original +Velleman software, like SetIOchannel, ReadADchannel, SendStepCCWFull and +many more, using /dev/velleman. + http://home.wanadoo.nl/hihihi/libk8000.htm + http://home.wanadoo.nl/hihihi/libk8005.htm + http://struyve.mine.nu:8080/index.php?block=k8000 + http://sourceforge.net/projects/libk8005/ diff --git a/Documentation/i2c/busses/i2c-parport-light b/Documentation/i2c/busses/i2c-parport-light new file mode 100644 index 000000000000..287436478520 --- /dev/null +++ b/Documentation/i2c/busses/i2c-parport-light @@ -0,0 +1,11 @@ +Kernel driver i2c-parport-light + +Author: Jean Delvare + +This driver is a light version of i2c-parport. It doesn't depend +on the parport driver, and uses direct I/O access instead. This might be +prefered on embedded systems where wasting memory for the clean but heavy +parport handling is not an option. The drawback is a reduced portability +and the impossibility to daisy-chain other parallel port devices. + +Please see i2c-parport for documentation. diff --git a/Documentation/i2c/busses/i2c-pca-isa b/Documentation/i2c/busses/i2c-pca-isa new file mode 100644 index 000000000000..6fc8f4c27c3c --- /dev/null +++ b/Documentation/i2c/busses/i2c-pca-isa @@ -0,0 +1,23 @@ +Kernel driver i2c-pca-isa + +Supported adapters: +This driver supports ISA boards using the Philips PCA 9564 +Parallel bus to I2C bus controller + +Author: Ian Campbell , Arcom Control Systems + +Module Parameters +----------------- + +* base int + I/O base address +* irq int + IRQ interrupt +* clock int + Clock rate as described in table 1 of PCA9564 datasheet + +Description +----------- + +This driver supports ISA boards using the Philips PCA 9564 +Parallel bus to I2C bus controller diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4 new file mode 100644 index 000000000000..856b4b8b962c --- /dev/null +++ b/Documentation/i2c/busses/i2c-piix4 @@ -0,0 +1,72 @@ +Kernel driver i2c-piix4 + +Supported adapters: + * Intel 82371AB PIIX4 and PIIX4E + * Intel 82443MX (440MX) + Datasheet: Publicly available at the Intel website + * ServerWorks OSB4, CSB5 and CSB6 southbridges + Datasheet: Only available via NDA from ServerWorks + * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge + Datasheet: Publicly available at the SMSC website http://www.smsc.com + +Authors: + Frodo Looijaard + Philip Edelbrock + + +Module Parameters +----------------- + +* force: int + Forcibly enable the PIIX4. DANGEROUS! +* force_addr: int + Forcibly enable the PIIX4 at the given address. EXTREMELY DANGEROUS! +* fix_hstcfg: int + Fix config register. Needed on some boards (Force CPCI735). + + +Description +----------- + +The PIIX4 (properly known as the 82371AB) is an Intel chip with a lot of +functionality. Among other things, it implements the PCI bus. One of its +minor functions is implementing a System Management Bus. This is a true +SMBus - you can not access it on I2C levels. The good news is that it +natively understands SMBus commands and you do not have to worry about +timing problems. The bad news is that non-SMBus devices connected to it can +confuse it mightily. Yes, this is known to happen... + +Do 'lspci -v' and see whether it contains an entry like this: + +0000:00:02.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) + Flags: medium devsel, IRQ 9 + +Bus and device numbers may differ, but the function number must be +identical (like many PCI devices, the PIIX4 incorporates a number of +different 'functions', which can be considered as separate devices). If you +find such an entry, you have a PIIX4 SMBus controller. + +On some computers (most notably, some Dells), the SMBus is disabled by +default. If you use the insmod parameter 'force=1', the kernel module will +try to enable it. THIS IS VERY DANGEROUS! If the BIOS did not set up a +correct address for this module, you could get in big trouble (read: +crashes, data corruption, etc.). Try this only as a last resort (try BIOS +updates first, for example), and backup first! An even more dangerous +option is 'force_addr='. This will not only enable the PIIX4 like +'force' foes, but it will also set a new base I/O port address. The SMBus +parts of the PIIX4 needs a range of 8 of these addresses to function +correctly. If these addresses are already reserved by some other device, +you will get into big trouble! DON'T USE THIS IF YOU ARE NOT VERY SURE +ABOUT WHAT YOU ARE DOING! + +The PIIX4E is just an new version of the PIIX4; it is supported as well. +The PIIX/PIIX3 does not implement an SMBus or I2C bus, so you can't use +this driver on those mainboards. + +The ServerWorks Southbridges, the Intel 440MX, and the Victory766 are +identical to the PIIX4 in I2C/SMBus support. + +A few OSB4 southbridges are known to be misconfigured by the BIOS. In this +case, you have you use the fix_hstcfg module parameter. Do not use it +unless you know you have to, because in some cases it also breaks +configuration on southbridges that don't need it. diff --git a/Documentation/i2c/busses/i2c-prosavage b/Documentation/i2c/busses/i2c-prosavage new file mode 100644 index 000000000000..703687902511 --- /dev/null +++ b/Documentation/i2c/busses/i2c-prosavage @@ -0,0 +1,23 @@ +Kernel driver i2c-prosavage + +Supported adapters: + + S3/VIA KM266/VT8375 aka ProSavage8 + S3/VIA KM133/VT8365 aka Savage4 + +Author: Henk Vergonet + +Description +----------- + +The Savage4 chips contain two I2C interfaces (aka a I2C 'master' or +'host'). + +The first interface is used for DDC (Data Display Channel) which is a +serial channel through the VGA monitor connector to a DDC-compliant +monitor. This interface is defined by the Video Electronics Standards +Association (VESA). The standards are available for purchase at +http://www.vesa.org . The second interface is a general-purpose I2C bus. + +Usefull for gaining access to the TV Encoder chips. + diff --git a/Documentation/i2c/busses/i2c-savage4 b/Documentation/i2c/busses/i2c-savage4 new file mode 100644 index 000000000000..6ecceab618d3 --- /dev/null +++ b/Documentation/i2c/busses/i2c-savage4 @@ -0,0 +1,26 @@ +Kernel driver i2c-savage4 + +Supported adapters: + * Savage4 + * Savage2000 + +Authors: + Alexander Wold , + Mark D. Studebaker + +Description +----------- + +The Savage4 chips contain two I2C interfaces (aka a I2C 'master' +or 'host'). + +The first interface is used for DDC (Data Display Channel) which is a +serial channel through the VGA monitor connector to a DDC-compliant +monitor. This interface is defined by the Video Electronics Standards +Association (VESA). The standards are available for purchase at +http://www.vesa.org . The DDC bus is not yet supported because its register +is not directly memory-mapped. + +The second interface is a general-purpose I2C bus. This is the only +interface supported by the driver at the moment. + diff --git a/Documentation/i2c/busses/i2c-sis5595 b/Documentation/i2c/busses/i2c-sis5595 new file mode 100644 index 000000000000..cc47db7d00a9 --- /dev/null +++ b/Documentation/i2c/busses/i2c-sis5595 @@ -0,0 +1,59 @@ +Kernel driver i2c-sis5595 + +Authors: + Frodo Looijaard , + Mark D. Studebaker , + Philip Edelbrock + +Supported adapters: + * Silicon Integrated Systems Corp. SiS5595 Southbridge + Datasheet: Publicly available at the Silicon Integrated Systems Corp. site. + +Note: all have mfr. ID 0x1039. + + SUPPORTED PCI ID + 5595 0008 + + Note: these chips contain a 0008 device which is incompatible with the + 5595. We recognize these by the presence of the listed + "blacklist" PCI ID and refuse to load. + + NOT SUPPORTED PCI ID BLACKLIST PCI ID + 540 0008 0540 + 550 0008 0550 + 5513 0008 5511 + 5581 0008 5597 + 5582 0008 5597 + 5597 0008 5597 + 5598 0008 5597/5598 + 630 0008 0630 + 645 0008 0645 + 646 0008 0646 + 648 0008 0648 + 650 0008 0650 + 651 0008 0651 + 730 0008 0730 + 735 0008 0735 + 745 0008 0745 + 746 0008 0746 + +Module Parameters +----------------- + +* force_addr=0xaddr Set the I/O base address. Useful for boards + that don't set the address in the BIOS. Does not do a + PCI force; the device must still be present in lspci. + Don't use this unless the driver complains that the + base address is not set. + +Description +----------- + +i2c-sis5595 is a true SMBus host driver for motherboards with the SiS5595 +southbridges. + +WARNING: If you are trying to access the integrated sensors on the SiS5595 +chip, you want the sis5595 driver for those, not this driver. This driver +is a BUS driver, not a CHIP driver. A BUS driver is used by other CHIP +drivers to access chips on the bus. + diff --git a/Documentation/i2c/busses/i2c-sis630 b/Documentation/i2c/busses/i2c-sis630 new file mode 100644 index 000000000000..9aca6889f748 --- /dev/null +++ b/Documentation/i2c/busses/i2c-sis630 @@ -0,0 +1,49 @@ +Kernel driver i2c-sis630 + +Supported adapters: + * Silicon Integrated Systems Corp (SiS) + 630 chipset (Datasheet: available at http://amalysh.bei.t-online.de/docs/SIS/) + 730 chipset + * Possible other SiS chipsets ? + +Author: Alexander Malysh + +Module Parameters +----------------- + +* force = [1|0] Forcibly enable the SIS630. DANGEROUS! + This can be interesting for chipsets not named + above to check if it works for you chipset, but DANGEROUS! + +* high_clock = [1|0] Forcibly set Host Master Clock to 56KHz (default, + what your BIOS use). DANGEROUS! This should be a bit + faster, but freeze some systems (i.e. my Laptop). + + +Description +----------- + +This SMBus only driver is known to work on motherboards with the above +named chipsets. + +If you see something like this: + +00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 31) +00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 + +or like this: + +00:00.0 Host bridge: Silicon Integrated Systems [SiS] 730 Host (rev 02) +00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 + +in your 'lspci' output , then this driver is for your chipset. + +Thank You +--------- +Philip Edelbrock +- testing SiS730 support +Mark M. Hoffman +- bug fixes + +To anyone else which I forgot here ;), thanks! + diff --git a/Documentation/i2c/busses/i2c-sis69x b/Documentation/i2c/busses/i2c-sis69x new file mode 100644 index 000000000000..5be48769f65b --- /dev/null +++ b/Documentation/i2c/busses/i2c-sis69x @@ -0,0 +1,73 @@ +Kernel driver i2c-sis96x + +Replaces 2.4.x i2c-sis645 + +Supported adapters: + * Silicon Integrated Systems Corp (SiS) + Any combination of these host bridges: + 645, 645DX (aka 646), 648, 650, 651, 655, 735, 745, 746 + and these south bridges: + 961, 962, 963(L) + +Author: Mark M. Hoffman + +Description +----------- + +This SMBus only driver is known to work on motherboards with the above +named chipset combinations. The driver was developed without benefit of a +proper datasheet from SiS. The SMBus registers are assumed compatible with +those of the SiS630, although they are located in a completely different +place. Thanks to Alexander Malysh for providing the +SiS630 datasheet (and driver). + +The command "lspci" as root should produce something like these lines: + +00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645 +00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 +00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016 + +or perhaps this... + +00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645 +00:02.0 ISA bridge: Silicon Integrated Systems [SiS]: Unknown device 0961 +00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016 + +(kernel versions later than 2.4.18 may fill in the "Unknown"s) + +If you cant see it please look on quirk_sis_96x_smbus +(drivers/pci/quirks.c) (also if southbridge detection fails) + +I suspect that this driver could be made to work for the following SiS +chipsets as well: 635, and 635T. If anyone owns a board with those chips +AND is willing to risk crashing & burning an otherwise well-behaved kernel +in the name of progress... please contact me at or +via the project's mailing list: . Please +send bug reports and/or success stories as well. + + +TO DOs +------ + +* The driver does not support SMBus block reads/writes; I may add them if a +scenario is found where they're needed. + + +Thank You +--------- + +Mark D. Studebaker + - design hints and bug fixes +Alexander Maylsh + - ditto, plus an important datasheet... almost the one I really wanted +Hans-Günter Lütke Uphues + - patch for SiS735 +Robert Zwerus + - testing for SiS645DX +Kianusch Sayah Karadji + - patch for SiS645DX/962 +Ken Healy + - patch for SiS655 + +To anyone else who has written w/ feedback, thanks! + diff --git a/Documentation/i2c/busses/i2c-via b/Documentation/i2c/busses/i2c-via new file mode 100644 index 000000000000..55edfe1a640b --- /dev/null +++ b/Documentation/i2c/busses/i2c-via @@ -0,0 +1,34 @@ +Kernel driver i2c-via + +Supported adapters: + * VIA Technologies, InC. VT82C586B + Datasheet: Publicly available at the VIA website + +Author: Kyösti Mälkki + +Description +----------- + +i2c-via is an i2c bus driver for motherboards with VIA chipset. + +The following VIA pci chipsets are supported: + - MVP3, VP3, VP2/97, VPX/97 + - others with South bridge VT82C586B + +Your lspci listing must show this : + + Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10) + + Problems? + + Q: You have VT82C586B on the motherboard, but not in the listing. + + A: Go to your BIOS setup, section PCI devices or similar. + Turn USB support on, and try again. + + Q: No error messages, but still i2c doesn't seem to work. + + A: This can happen. This driver uses the pins VIA recommends in their + datasheets, but there are several ways the motherboard manufacturer + can actually wire the lines. + diff --git a/Documentation/i2c/busses/i2c-viapro b/Documentation/i2c/busses/i2c-viapro new file mode 100644 index 000000000000..702f5ac68c09 --- /dev/null +++ b/Documentation/i2c/busses/i2c-viapro @@ -0,0 +1,47 @@ +Kernel driver i2c-viapro + +Supported adapters: + * VIA Technologies, Inc. VT82C596A/B + Datasheet: Sometimes available at the VIA website + + * VIA Technologies, Inc. VT82C686A/B + Datasheet: Sometimes available at the VIA website + + * VIA Technologies, Inc. VT8231, VT8233, VT8233A, VT8235, VT8237 + Datasheet: available on request from Via + +Authors: + Frodo Looijaard , + Philip Edelbrock , + Kyösti Mälkki , + Mark D. Studebaker + +Module Parameters +----------------- + +* force: int + Forcibly enable the SMBus controller. DANGEROUS! +* force_addr: int + Forcibly enable the SMBus at the given address. EXTREMELY DANGEROUS! + +Description +----------- + +i2c-viapro is a true SMBus host driver for motherboards with one of the +supported VIA southbridges. + +Your lspci -n listing must show one of these : + + device 1106:3050 (VT82C596 function 3) + device 1106:3051 (VT82C596 function 3) + device 1106:3057 (VT82C686 function 4) + device 1106:3074 (VT8233) + device 1106:3147 (VT8233A) + device 1106:8235 (VT8231) + devide 1106:3177 (VT8235) + devide 1106:3227 (VT8237) + +If none of these show up, you should look in the BIOS for settings like +enable ACPI / SMBus or even USB. + + diff --git a/Documentation/i2c/busses/i2c-voodoo3 b/Documentation/i2c/busses/i2c-voodoo3 new file mode 100644 index 000000000000..62d90a454d39 --- /dev/null +++ b/Documentation/i2c/busses/i2c-voodoo3 @@ -0,0 +1,62 @@ +Kernel driver i2c-voodoo3 + +Supported adapters: + * 3dfx Voodoo3 based cards + * Voodoo Banshee based cards + +Authors: + Frodo Looijaard , + Philip Edelbrock , + Ralph Metzler , + Mark D. Studebaker + +Main contact: Philip Edelbrock + +The code is based upon Ralph's test code (he did the hard stuff ;') + +Description +----------- + +The 3dfx Voodoo3 chip contains two I2C interfaces (aka a I2C 'master' or +'host'). + +The first interface is used for DDC (Data Display Channel) which is a +serial channel through the VGA monitor connector to a DDC-compliant +monitor. This interface is defined by the Video Electronics Standards +Association (VESA). The standards are available for purchase at +http://www.vesa.org . + +The second interface is a general-purpose I2C bus. The intent by 3dfx was +to allow manufacturers to add extra chips to the video card such as a +TV-out chip such as the BT869 or possibly even I2C based temperature +sensors like the ADM1021 or LM75. + +Stability +--------- + +Seems to be stable on the test machine, but needs more testing on other +machines. Simultaneous accesses of the DDC and I2C busses may cause errors. + +Supported Devices +----------------- + +Specifically, this driver was written and tested on the '3dfx Voodoo3 AGP +3000' which has a tv-out feature (s-video or composite). According to the +docs and discussions, this code should work for any Voodoo3 based cards as +well as Voodoo Banshee based cards. The DDC interface has been tested on a +Voodoo Banshee card. + +Issues +------ + +Probably many, but it seems to work OK on my system. :') + + +External Device Connection +-------------------------- + +The digital video input jumpers give availability to the I2C bus. +Specifically, pins 13 and 25 (bottom row middle, and bottom right-end) are +the I2C clock and I2C data lines, respectively. +5V and GND are probably +also easily available making the addition of extra I2C/SMBus devices easy +to implement. diff --git a/Documentation/i2c/busses/scx200_acb b/Documentation/i2c/busses/scx200_acb new file mode 100644 index 000000000000..08c8cd1df60c --- /dev/null +++ b/Documentation/i2c/busses/scx200_acb @@ -0,0 +1,14 @@ +Kernel driver scx200_acb + +Author: Christer Weinigel + +Module Parameters +----------------- + +* base: int + Base addresses for the ACCESS.bus controllers + +Description +----------- + +Enable the use of the ACCESS.bus controllers of a SCx200 processor. -- cgit v1.2.3