| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and wireguard.
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind"
* tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
nfp: clean mc addresses in application firmware when closing port
selftests: mptcp: pm_nl_ctl: fix 32-bit support
selftests: mptcp: depend on SYN_COOKIES
selftests: mptcp: userspace_pm: report errors with 'remove' tests
selftests: mptcp: userspace_pm: use correct server port
selftests: mptcp: sockopt: return error if wrong mark
selftests: mptcp: sockopt: use 'iptables-legacy' if available
selftests: mptcp: connect: fail if nft supposed to work
mptcp: do not rely on implicit state check in mptcp_listen()
mptcp: ensure subflow is unhashed before cleaning the backlog
s390/qeth: Fix vipa deletion
octeontx-af: fix hardware timestamp configuration
net: dsa: sja1105: always enable the send_meta options
net: dsa: tag_sja1105: fix MAC DA patching from meta frames
net: Replace strlcpy with strscpy
pptp: Fix fib lookup calls.
mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check
net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
xsk: Honor SO_BINDTODEVICE on bind
ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-07-05
We've added 2 non-merge commits during the last 1 day(s) which contain
a total of 3 files changed, 16 insertions(+), 4 deletions(-).
The main changes are:
1) Fix BTF to warn but not returning an error for a NULL BTF to still be
able to load modules under CONFIG_DEBUG_INFO_BTF, from SeongJae Park.
2) Fix xsk sockets to honor SO_BINDTODEVICE in bind(), from Ilya Maximets.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
xsk: Honor SO_BINDTODEVICE on bind
bpf, btf: Warn but return no error for NULL btf from __register_btf_kfunc_id_set()
====================
Link: https://lore.kernel.org/r/20230705171716.6494-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the blamed commit, closing the first subflow resets the first
subflow socket state to SS_UNCONNECTED.
The current mptcp listen implementation relies only on such
state to prevent touching not-fully-disconnected sockets.
Incoming mptcp fastclose (or paired endpoint removal) unconditionally
closes the first subflow.
All the above allows an incoming fastclose followed by a listen() call
to successfully race with a blocking recvmsg(), potentially causing the
latter to hit a divide by zero bug in cleanup_rbuf/__tcp_select_window().
Address the issue explicitly checking the msk socket state in
mptcp_listen(). An alternative solution would be moving the first
subflow socket state update into mptcp_disconnect(), but in the long
term the first subflow socket should be removed: better avoid relaying
on it for internal consistency check.
Fixes: b29fcfb54cd7 ("mptcp: full disconnect implementation")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/414
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While tacking care of the mptcp-level listener I unintentionally
moved the subflow level unhash after the subflow listener backlog
cleanup.
That could cause some nasty race and makes the code harder to read.
Address the issue restoring the proper order of operations.
Fixes: 57fc0f1ceaa4 ("mptcp: ensure listener is unhashed before updating the sk status")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
incl_srcpt has the limitation, mentioned in commit b4638af8885a ("net:
dsa: sja1105: always enable the INCL_SRCPT option"), that frames with a
MAC DA of 01:80:c2:xx:yy:zz will be received as 01:80:c2:00:00:zz unless
PTP RX timestamping is enabled.
The incl_srcpt option was initially unconditionally enabled, then that
changed with commit 42824463d38d ("net: dsa: sja1105: Limit use of
incl_srcpt to bridge+vlan mode"), then again with b4638af8885a ("net:
dsa: sja1105: always enable the INCL_SRCPT option"). Bottom line is that
it now needs to be always enabled, otherwise the driver does not have a
reliable source of information regarding source_port and switch_id for
link-local traffic (tag_8021q VLANs may be imprecise since now they
identify an entire bridging domain when ports are not standalone).
If we accept that PTP RX timestamping (and therefore, meta frame
generation) is always enabled in hardware, then that limitation could be
avoided and packets with any MAC DA can be properly received, because
meta frames do contain the original bytes from the MAC DA of their
associated link-local packet.
This change enables meta frame generation unconditionally, which also
has the nice side effects of simplifying the switch control path
(a switch reset is no longer required on hwtstamping settings change)
and the tagger data path (it no longer needs to be informed whether to
expect meta frames or not - it always does).
Fixes: 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SJA1105 manual says that at offset 4 into the meta frame payload we
have "MAC destination byte 2" and at offset 5 we have "MAC destination
byte 1". These are counted from the LSB, so byte 1 is h_dest[ETH_HLEN-2]
aka h_dest[4] and byte 2 is h_dest[ETH_HLEN-3] aka h_dest[3].
The sja1105_meta_unpack() function decodes these the other way around,
so a frame with MAC DA 01:80:c2:11:22:33 is received by the network
stack as having 01:80:c2:22:11:33.
Fixes: e53e18a6fe4d ("net: dsa: sja1105: Receive and decode meta frames")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The attribute TCA_PEDIT_PARMS_EX is not be included in pedit_policy and
one malicious user could fake a TCA_PEDIT_PARMS_EX whose length is
smaller than the intended sizeof(struct tc_pedit). Hence, the
dereference in tcf_pedit_init() could access dirty heap data.
static int tcf_pedit_init(...)
{
// ...
pattr = tb[TCA_PEDIT_PARMS]; // TCA_PEDIT_PARMS is included
if (!pattr)
pattr = tb[TCA_PEDIT_PARMS_EX]; // but this is not
// ...
parm = nla_data(pattr);
index = parm->index; // parm is able to be smaller than 4 bytes
// and this dereference gets dirty skb_buff
// data created in netlink_sendmsg
}
This commit adds TCA_PEDIT_PARMS_EX length in pedit_policy which avoid
the above case, just like the TCA_PEDIT_PARMS.
Fixes: 71d0ed7079df ("net/act_pedit: Support using offset relative to the conventional network headers")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Link: https://lore.kernel.org/r/20230703110842.590282-1-linma@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Initial creation of an AF_XDP socket requires CAP_NET_RAW capability. A
privileged process might create the socket and pass it to a non-privileged
process for later use. However, that process will be able to bind the socket
to any network interface. Even though it will not be able to receive any
traffic without modification of the BPF map, the situation is not ideal.
Sockets already have a mechanism that can be used to restrict what interface
they can be attached to. That is SO_BINDTODEVICE.
To change the SO_BINDTODEVICE binding the process will need CAP_NET_RAW.
Make xsk_bind() honor the SO_BINDTODEVICE in order to allow safer workflow
when non-privileged process is using AF_XDP.
The intended workflow is following:
1. First process creates a bare socket with socket(AF_XDP, ...).
2. First process loads the XSK program to the interface.
3. First process adds the socket fd to a BPF map.
4. First process ties socket fd to a particular interface using
SO_BINDTODEVICE.
5. First process sends socket fd to a second process.
6. Second process allocates UMEM.
7. Second process binds socket to the interface with bind(...).
8. Second process sends/receives the traffic.
All the steps above are possible today if the first process is privileged
and the second one has sufficient RLIMIT_MEMLOCK and no capabilities.
However, the second process will be able to bind the socket to any interface
it wants on step 7 and send traffic from it. With the proposed change, the
second process will be able to bind the socket only to a specific interface
chosen by the first process at step 4.
Fixes: 965a99098443 ("xsk: add support for bind for Rx")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/bpf/20230703175329.3259672-1-i.maximets@ovn.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
|
|
request sockets are lockless, __tcp_oow_rate_limited() could be called
on the same object from different cpus. This is harmless.
Add READ_ONCE()/WRITE_ONCE() annotations to avoid a KCSAN report.
Fixes: 4ce7e93cb3fe ("tcp: rate limit ACK sent by SYN_RECV request sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was a regression introduced by the blamed commit, where pinging to
a VLAN-unaware bridge would fail with the repeated message "Couldn't
decode source port" coming from the tagging protocol driver.
When receiving packets with a bridge_vid as determined by
dsa_tag_8021q_bridge_join(), dsa_8021q_rcv() will decode:
- source_port = 0 (which isn't really valid, more like "don't know")
- switch_id = 0 (which isn't really valid, more like "don't know")
- vbid = value in range 1-7
Since the blamed patch has reversed the order of the checks, we are now
going to believe that source_port != -1 and switch_id != -1, so they're
valid, but they aren't.
The minimal solution to the problem is to only populate source_port and
switch_id with what dsa_8021q_rcv() came up with, if the vbid is zero,
i.e. the source port information is trustworthy.
Fixes: c1ae02d87689 ("net: dsa: tag_sja1105: always prefer source port information from INCL_SRCPT")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the synchronization rules for .ndo_get_stats() as seen in
Documentation/networking/netdevices.rst, acquiring a plain spin_lock()
should not be illegal, but the bridge driver implementation makes it so.
After running these commands, I am being faced with the following
lockdep splat:
$ ip link add link swp0 name macsec0 type macsec encrypt on && ip link set swp0 up
$ ip link add dev br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set macsec0 master br0 && ip link set macsec0 up
========================================================
WARNING: possible irq lock inversion dependency detected
6.4.0-04295-g31b577b4bd4a #603 Not tainted
--------------------------------------------------------
swapper/1/0 just changed the state of lock:
ffff6bd348724cd8 (&br->lock){+.-.}-{3:3}, at: br_forward_delay_timer_expired+0x34/0x198
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&ocelot->stats_lock){+.+.}-{3:3}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Chain exists of:
&br->lock --> &br->hash_lock --> &ocelot->stats_lock
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ocelot->stats_lock);
local_irq_disable();
lock(&br->lock);
lock(&br->hash_lock);
<Interrupt>
lock(&br->lock);
*** DEADLOCK ***
(details about the 3 locks skipped)
swp0 is instantiated by drivers/net/dsa/ocelot/felix.c, and this
only matters to the extent that its .ndo_get_stats64() method calls
spin_lock(&ocelot->stats_lock).
Documentation/locking/lockdep-design.rst says:
| A lock is irq-safe means it was ever used in an irq context, while a lock
| is irq-unsafe means it was ever acquired with irq enabled.
(...)
| Furthermore, the following usage based lock dependencies are not allowed
| between any two lock-classes::
|
| <hardirq-safe> -> <hardirq-unsafe>
| <softirq-safe> -> <softirq-unsafe>
Lockdep marks br->hash_lock as softirq-safe, because it is sometimes
taken in softirq context (for example br_fdb_update() which runs in
NET_RX softirq), and when it's not in softirq context it blocks softirqs
by using spin_lock_bh().
Lockdep marks ocelot->stats_lock as softirq-unsafe, because it never
blocks softirqs from running, and it is never taken from softirq
context. So it can always be interrupted by softirqs.
There is a call path through which a function that holds br->hash_lock:
fdb_add_hw_addr() will call a function that acquires ocelot->stats_lock:
ocelot_port_get_stats64(). This can be seen below:
ocelot_port_get_stats64+0x3c/0x1e0
felix_get_stats64+0x20/0x38
dsa_slave_get_stats64+0x3c/0x60
dev_get_stats+0x74/0x2c8
rtnl_fill_stats+0x4c/0x150
rtnl_fill_ifinfo+0x5cc/0x7b8
rtmsg_ifinfo_build_skb+0xe4/0x150
rtmsg_ifinfo+0x5c/0xb0
__dev_notify_flags+0x58/0x200
__dev_set_promiscuity+0xa0/0x1f8
dev_set_promiscuity+0x30/0x70
macsec_dev_change_rx_flags+0x68/0x88
__dev_set_promiscuity+0x1a8/0x1f8
__dev_set_rx_mode+0x74/0xa8
dev_uc_add+0x74/0xa0
fdb_add_hw_addr+0x68/0xd8
fdb_add_local+0xc4/0x110
br_fdb_add_local+0x54/0x88
br_add_if+0x338/0x4a0
br_add_slave+0x20/0x38
do_setlink+0x3a4/0xcb8
rtnl_newlink+0x758/0x9d0
rtnetlink_rcv_msg+0x2f0/0x550
netlink_rcv_skb+0x128/0x148
rtnetlink_rcv+0x24/0x38
the plain English explanation for it is:
The macsec0 bridge port is created without p->flags & BR_PROMISC,
because it is what br_manage_promisc() decides for a VLAN filtering
bridge with a single auto port.
As part of the br_add_if() procedure, br_fdb_add_local() is called for
the MAC address of the device, and this results in a call to
dev_uc_add() for macsec0 while the softirq-safe br->hash_lock is taken.
Because macsec0 does not have IFF_UNICAST_FLT, dev_uc_add() ends up
calling __dev_set_promiscuity() for macsec0, which is propagated by its
implementation, macsec_dev_change_rx_flags(), to the lower device: swp0.
This triggers the call path:
dev_set_promiscuity(swp0)
-> rtmsg_ifinfo()
-> dev_get_stats()
-> ocelot_port_get_stats64()
with a calling context that lockdep doesn't like (br->hash_lock held).
Normally we don't see this, because even though many drivers that can be
bridge ports don't support IFF_UNICAST_FLT, we need a driver that
(a) doesn't support IFF_UNICAST_FLT, *and*
(b) it forwards the IFF_PROMISC flag to another driver, and
(c) *that* driver implements ndo_get_stats64() using a softirq-unsafe
spinlock.
Condition (b) is necessary because the first __dev_set_rx_mode() calls
__dev_set_promiscuity() with "bool notify=false", and thus, the
rtmsg_ifinfo() code path won't be entered.
The same criteria also hold true for DSA switches which don't report
IFF_UNICAST_FLT. When the DSA master uses a spin_lock() in its
ndo_get_stats64() method, the same lockdep splat can be seen.
I think the deadlock possibility is real, even though I didn't reproduce
it, and I'm thinking of the following situation to support that claim:
fdb_add_hw_addr() runs on a CPU A, in a context with softirqs locally
disabled and br->hash_lock held, and may end up attempting to acquire
ocelot->stats_lock.
In parallel, ocelot->stats_lock is currently held by a thread B (say,
ocelot_check_stats_work()), which is interrupted while holding it by a
softirq which attempts to lock br->hash_lock.
Thread B cannot make progress because br->hash_lock is held by A. Whereas
thread A cannot make progress because ocelot->stats_lock is held by B.
When taking the issue at face value, the bridge can avoid that problem
by simply making the ports promiscuous from a code path with a saner
calling context (br->hash_lock not held). A bridge port without
IFF_UNICAST_FLT is going to become promiscuous as soon as we call
dev_uc_add() on it (which we do unconditionally), so why not be
preemptive and make it promiscuous right from the beginning, so as to
not be taken by surprise.
With this, we've broken the links between code that holds br->hash_lock
or br->lock and code that calls into the ndo_change_rx_flags() or
ndo_get_stats64() ops of the bridge port.
Fixes: 2796d0c648c9 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NFS client updates from Trond Myklebust:
"Stable fixes and other bugfixes:
- nfs: don't report STATX_BTIME in ->getattr
- Revert 'NFSv4: Retry LOCK on OLD_STATEID during delegation return'
since it breaks NFSv4 state recovery.
- NFSv4.1: freeze the session table upon receiving NFS4ERR_BADSESSION
- Fix the NFSv4.2 xattr cache shrinker_id
- Force a ctime update after a NFSv4.2 SETXATTR call
Features and cleanups:
- NFS and RPC over TLS client code from Chuck Lever
- Support for use of abstract unix socket addresses with the rpcbind
daemon
- Sysfs API to allow shutdown of the kernel RPC client and prevent
umount() hangs if the server is known to be permanently down
- XDR cleanups from Anna"
* tag 'nfs-for-6.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (33 commits)
Revert "NFSv4: Retry LOCK on OLD_STATEID during delegation return"
NFS: Don't cleanup sysfs superblock entry if uninitialized
nfs: don't report STATX_BTIME in ->getattr
NFSv4.1: freeze the session table upon receiving NFS4ERR_BADSESSION
NFSv4.2: fix wrong shrinker_id
NFSv4: Clean up some shutdown loops
NFS: Cancel all existing RPC tasks when shutdown
NFS: add sysfs shutdown knob
NFS: add a sysfs link to the acl rpc_client
NFS: add a sysfs link to the lockd rpc_client
NFS: Add sysfs links to sunrpc clients for nfs_clients
NFS: add superblock sysfs entries
NFS: Make all of /sys/fs/nfs network-namespace unique
NFS: Open-code the nfs_kset kset_create_and_add()
NFS: rename nfs_client_kobj to nfs_net_kobj
NFS: rename nfs_client_kset to nfs_kset
NFS: Add an "xprtsec=" NFS mount option
NFS: Have struct nfs_client carry a TLS policy field
SUNRPC: Add a TCP-with-TLS RPC transport class
SUNRPC: Capture CMSG metadata on client-side receive
...
|
|
The ISO Interval on CIS Established Event uses 1.25 ms slots:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 2304:
Time = N * 1.25 ms
In addition to that this always update the QoS settings based on CIS
Established Event.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use kmemdup rather than duplicating its implementation.
./net/bluetooth/hci_conn.c:1880:7-14: WARNING opportunity for kmemdup.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5597
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the driver core allows for struct class to be in read-only
memory, move the bt_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This rework sync_interval to be sync_factor as having sync_interval in
the order of seconds is sometimes not disarable.
Wit sync_factor the application can tell how many SDU intervals it wants
to send an announcement with PA, the EA interval is set to 2 times that
so a factor of 24 of BIG SDU interval of 10ms would look like the
following:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x01
Properties: 0x0000
Min advertising interval: 480.000 msec (0x0300)
Max advertising interval: 480.000 msec (0x0300)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: Host has no preference (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 2M (0x02)
SID: 0x00
Scan request notifications: Disabled (0x00)
< HCI Command: LE Set Periodic Advertising Parameters (0x08|0x003e) plen 7
Handle: 1
Min interval: 240.00 msec (0x00c0)
Max interval: 240.00 msec (0x00c0)
Properties: 0x0000
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When receiving a scan response there is no way to know if the remote
device is connectable or not, so when it cannot be merged don't
make any assumption and instead just mark it with a new flag defined as
MGMT_DEV_FOUND_SCAN_RSP so userspace can tell it is a standalone
SCAN_RSP.
Link: https://lore.kernel.org/linux-bluetooth/CABBYNZ+CYMsDSPTxBn09Js3BcdC-x7vZFfyLJ3ppZGGwJKmUTw@mail.gmail.com/
Fixes: c70a7e4cc8d2 ("Bluetooth: Add support for Not Connectable flag for Device Found events")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the event has error status, return right error code and don't show
incorrect "response malformed" messages.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When reconfiguring CIG after disconnection of the last CIS, LE Remove
CIG shall be sent before LE Set CIG Parameters. Otherwise, it fails
because CIG is in the inactive state and not configurable (Core v5.3
Vol 6 Part B Sec. 4.5.14.3). This ordering is currently wrong under
suitable timing conditions, because LE Remove CIG is sent via the
hci_sync queue and may be delayed, but Set CIG Parameters is via
hci_send_cmd.
Make the ordering well-defined by sending also Set CIG Parameters via
hci_sync.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
l2cap_sock_release(sk) frees sk. However, sk's children are still alive
and point to the already free'd sk's address.
To fix this, l2cap_sock_release(sk) also cleans sk's children.
==================================================================
BUG: KASAN: use-after-free in l2cap_sock_ready_cb+0xb7/0x100 net/bluetooth/l2cap_sock.c:1650
Read of size 8 at addr ffff888104617aa8 by task kworker/u3:0/276
CPU: 0 PID: 276 Comm: kworker/u3:0 Not tainted 6.2.0-00001-gef397bd4d5fb-dirty #59
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Workqueue: hci2 hci_rx_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x72/0x95 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:306 [inline]
print_report+0x175/0x478 mm/kasan/report.c:417
kasan_report+0xb1/0x130 mm/kasan/report.c:517
l2cap_sock_ready_cb+0xb7/0x100 net/bluetooth/l2cap_sock.c:1650
l2cap_chan_ready+0x10e/0x1e0 net/bluetooth/l2cap_core.c:1386
l2cap_config_req+0x753/0x9f0 net/bluetooth/l2cap_core.c:4480
l2cap_bredr_sig_cmd net/bluetooth/l2cap_core.c:5739 [inline]
l2cap_sig_channel net/bluetooth/l2cap_core.c:6509 [inline]
l2cap_recv_frame+0xe2e/0x43c0 net/bluetooth/l2cap_core.c:7788
l2cap_recv_acldata+0x6ed/0x7e0 net/bluetooth/l2cap_core.c:8506
hci_acldata_packet net/bluetooth/hci_core.c:3813 [inline]
hci_rx_work+0x66e/0xbc0 net/bluetooth/hci_core.c:4048
process_one_work+0x4ea/0x8e0 kernel/workqueue.c:2289
worker_thread+0x364/0x8e0 kernel/workqueue.c:2436
kthread+0x1b9/0x200 kernel/kthread.c:376
ret_from_fork+0x2c/0x50 arch/x86/entry/entry_64.S:308
</TASK>
Allocated by task 288:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
____kasan_kmalloc mm/kasan/common.c:374 [inline]
__kasan_kmalloc+0x82/0x90 mm/kasan/common.c:383
kasan_kmalloc include/linux/kasan.h:211 [inline]
__do_kmalloc_node mm/slab_common.c:968 [inline]
__kmalloc+0x5a/0x140 mm/slab_common.c:981
kmalloc include/linux/slab.h:584 [inline]
sk_prot_alloc+0x113/0x1f0 net/core/sock.c:2040
sk_alloc+0x36/0x3c0 net/core/sock.c:2093
l2cap_sock_alloc.constprop.0+0x39/0x1c0 net/bluetooth/l2cap_sock.c:1852
l2cap_sock_create+0x10d/0x220 net/bluetooth/l2cap_sock.c:1898
bt_sock_create+0x183/0x290 net/bluetooth/af_bluetooth.c:132
__sock_create+0x226/0x380 net/socket.c:1518
sock_create net/socket.c:1569 [inline]
__sys_socket_create net/socket.c:1606 [inline]
__sys_socket_create net/socket.c:1591 [inline]
__sys_socket+0x112/0x200 net/socket.c:1639
__do_sys_socket net/socket.c:1652 [inline]
__se_sys_socket net/socket.c:1650 [inline]
__x64_sys_socket+0x40/0x50 net/socket.c:1650
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 288:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
kasan_save_free_info+0x2e/0x50 mm/kasan/generic.c:523
____kasan_slab_free mm/kasan/common.c:236 [inline]
____kasan_slab_free mm/kasan/common.c:200 [inline]
__kasan_slab_free+0x10a/0x190 mm/kasan/common.c:244
kasan_slab_free include/linux/kasan.h:177 [inline]
slab_free_hook mm/slub.c:1781 [inline]
slab_free_freelist_hook mm/slub.c:1807 [inline]
slab_free mm/slub.c:3787 [inline]
__kmem_cache_free+0x88/0x1f0 mm/slub.c:3800
sk_prot_free net/core/sock.c:2076 [inline]
__sk_destruct+0x347/0x430 net/core/sock.c:2168
sk_destruct+0x9c/0xb0 net/core/sock.c:2183
__sk_free+0x82/0x220 net/core/sock.c:2194
sk_free+0x7c/0xa0 net/core/sock.c:2205
sock_put include/net/sock.h:1991 [inline]
l2cap_sock_kill+0x256/0x2b0 net/bluetooth/l2cap_sock.c:1257
l2cap_sock_release+0x1a7/0x220 net/bluetooth/l2cap_sock.c:1428
__sock_release+0x80/0x150 net/socket.c:650
sock_close+0x19/0x30 net/socket.c:1368
__fput+0x17a/0x5c0 fs/file_table.c:320
task_work_run+0x132/0x1c0 kernel/task_work.c:179
resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
exit_to_user_mode_prepare+0x113/0x120 kernel/entry/common.c:203
__syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
syscall_exit_to_user_mode+0x21/0x50 kernel/entry/common.c:296
do_syscall_64+0x4c/0x90 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x72/0xdc
The buggy address belongs to the object at ffff888104617800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 680 bytes inside of
1024-byte region [ffff888104617800, ffff888104617c00)
The buggy address belongs to the physical page:
page:00000000dbca6a80 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888104614000 pfn:0x104614
head:00000000dbca6a80 order:2 compound_mapcount:0 subpages_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffff888100041dc0 ffffea0004212c10 ffffea0004234b10
raw: ffff888104614000 0000000000080002 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888104617980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888104617a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff888104617a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888104617b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888104617b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Ack: This bug is found by FuzzBT with a modified Syzkaller. Other
contributors are Ruoyu Wu and Hui Peng.
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Devices that lack persistent storage for the device address can indicate
this by setting the HCI_QUIRK_INVALID_BDADDR which causes the controller
to be marked as unconfigured until user space has set a valid address.
The related HCI_QUIRK_USE_BDADDR_PROPERTY was later added to similarly
indicate that the device lacks a valid address but that one may be
specified in the devicetree.
As is clear from commit 7a0e5b15ca45 ("Bluetooth: Add quirk for reading
BD_ADDR from fwnode property") that added and documented this quirk and
commits like de79a9df1692 ("Bluetooth: btqcomsmd: use
HCI_QUIRK_USE_BDADDR_PROPERTY"), the device address of controllers with
this flag should be treated as invalid until user space has had a chance
to configure the controller in case the devicetree property is missing.
As it does not make sense to allow controllers with invalid addresses,
restore the original semantics, which also makes sure that the
implementation is consistent (e.g. get_missing_options() indicates that
the address must be set) and matches the documentation (including
comments in the code, such as, "In case any of them is set, the
controller has to start up as unconfigured.").
Fixes: e668eb1e1578 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Devices that lack persistent storage for the device address can indicate
this by setting the HCI_QUIRK_INVALID_BDADDR which causes the controller
to be marked as unconfigured until user space has set a valid address.
Once configured, the device address must be set on every setup for
controllers with HCI_QUIRK_NON_PERSISTENT_SETUP to avoid marking the
controller as unconfigured and requiring the address to be set again.
Fixes: 740011cfe948 ("Bluetooth: Add new quirk for non-persistent setup settings")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix potential use-after-free in l2cap_le_command_rej.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the sja1105 tagging protocol prefers using the source port
information from the VLAN header if that is available, falling back to
the INCL_SRCPT option if it isn't. The VLAN header is available for all
frames except for META frames initiated by the switch (containing RX
timestamps), and thus, the "if (is_link_local)" branch is practically
dead.
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port. With incorrect
source port reporting, for example PTP traffic over 2 bridged ports will
all be seen on sockets opened on the first such port, which is incorrect.
Now that the tagging protocol has been changed to make link-local frames
always contain source port information, we can reverse the order of the
checks so that we always give precedence to that information (which is
always precise) in lieu of the tag_8021q VID which is only precise for a
standalone port.
Fixes: d7f9787a763f ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fcec ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
xtables relies on skb being owned by ip stack, i.e. with ipv4
check in place skb->cb is supposed to be IPCB.
I don't see an immediate problem (REJECT target cannot be used anymore
now that PRE/POSTROUTING hook validation has been fixed), but better be
safe than sorry.
A much better patch would be to either mark act_ipt as
"depends on BROKEN" or remove it altogether. I plan to do this
for -next in the near future.
This tc extension is broken in the sense that tc lacks an
equivalent of NF_STOLEN verdict.
With NF_STOLEN, target function takes complete ownership of skb, caller
cannot dereference it anymore.
ACT_STOLEN cannot be used for this: it has a different meaning, caller
is allowed to dereference the skb.
At this time NF_STOLEN won't be returned by any targets as far as I can
see, but this may change in the future.
It might be possible to work around this via list of allowed
target extensions known to only return DROP or ACCEPT verdicts, but this
is error prone/fragile.
Existing selftest only validates xt_LOG and act_ipt is restricted
to ipv4 so I don't think this action is used widely.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Netfilter targets make assumptions on the skb state, for example
iphdr is supposed to be in the linear area.
This is normally done by IP stack, but in act_ipt case no
such checks are made.
Some targets can even assume that skb_dst will be valid.
Make a minimum effort to check for this:
- Don't call the targets eval function for non-ipv4 skbs.
- Don't call the targets eval function for POSTROUTING
emulation when the skb has no dst set.
v3: use skb_protocol helper (Davide Caratti)
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Looks like "tc" hard-codes "mangle" as the only supported table
name, but on kernel side there are no checks.
This is wrong. Not all xtables targets are safe to call from tc.
E.g. "nat" targets assume skb has a conntrack object assigned to it.
Normally those get called from netfilter nat core which consults the
nat table to obtain the address mapping.
"tc" userspace either sets PRE or POSTROUTING as hook number, but there
is no validation of this on kernel side, so update netlink policy to
reject bogus numbers. Some targets may assume skb_dst is set for
input/forward hooks, so prevent those from being used.
act_ipt uses the hook number in two places:
1. the state hook number, this is fine as-is
2. to set par.hook_mask
The latter is a bit mask, so update the assignment to make
xt_check_target() to the right thing.
Followup patch adds required checks for the skb/packet headers before
calling the targets evaluation function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As &net->sctp.addr_wq_lock is also acquired by the timer
sctp_addr_wq_timeout_handler() in protocal.c, the same lock acquisition
at sctp_auto_asconf_init() seems should disable irq since it is called
from sctp_accept() under process context.
Possible deadlock scenario:
sctp_accept()
-> sctp_sock_migrate()
-> sctp_auto_asconf_init()
-> spin_lock(&net->sctp.addr_wq_lock)
<timer interrupt>
-> sctp_addr_wq_timeout_handler()
-> spin_lock_bh(&net->sctp.addr_wq_lock); (deadlock here)
This flaw was found using an experimental static analysis tool we are
developing for irq-related deadlock.
The tentative patch fix the potential deadlock by spin_lock_bh().
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Fixes: 34e5b0118685 ("sctp: delay auto_asconf init until binding the first addr")
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20230627120340.19432-1-dg573847474@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
- Yosry Ahmed brought back some cgroup v1 stats in OOM logs
- Yosry has also eliminated cgroup's atomic rstat flushing
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning
- Lorenzo Stoakes has done some maintanance work on the
get_user_pages() interface
- Liam Howlett continues with cleanups and maintenance work to the
maple tree code. Peng Zhang also does some work on maple tree
- Johannes Weiner has done some cleanup work on the compaction code
- David Hildenbrand has contributed additional selftests for
get_user_pages()
- Thomas Gleixner has contributed some maintenance and optimization
work for the vmalloc code
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting
- Christoph Hellwig has some cleanups for the filemap/directio code
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the
provided APIs rather than open-coding accesses
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings
- John Hubbard has a series of fixes to the MM selftesting code
- ZhangPeng continues the folio conversion campaign
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment
from 128 to 8
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code
- Vishal Moola also has done some folio conversion work
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch
* tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (380 commits)
mm/hugetlb: remove hugetlb_set_page_subpool()
mm: nommu: correct the range of mmap_sem_read_lock in task_mem()
hugetlb: revert use of page_cache_next_miss()
Revert "page cache: fix page_cache_next/prev_miss off by one"
mm/vmscan: fix root proactive reclaim unthrottling unbalanced node
mm: memcg: rename and document global_reclaim()
mm: kill [add|del]_page_to_lru_list()
mm: compaction: convert to use a folio in isolate_migratepages_block()
mm: zswap: fix double invalidate with exclusive loads
mm: remove unnecessary pagevec includes
mm: remove references to pagevec
mm: rename invalidate_mapping_pagevec to mapping_try_invalidate
mm: remove struct pagevec
net: convert sunrpc from pagevec to folio_batch
i915: convert i915_gpu_error to use a folio_batch
pagevec: rename fbatch_count()
mm: remove check_move_unevictable_pages()
drm: convert drm_gem_put_pages() to use a folio_batch
i915: convert shmem_sg_free_table() to use a folio_batch
scatterlist: add sg_set_folio()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"There are three areas of note:
A bunch of strlcpy()->strscpy() conversions ended up living in my tree
since they were either Acked by maintainers for me to carry, or got
ignored for multiple weeks (and were trivial changes).
The compiler option '-fstrict-flex-arrays=3' has been enabled
globally, and has been in -next for the entire devel cycle. This
changes compiler diagnostics (though mainly just -Warray-bounds which
is disabled) and potential UBSAN_BOUNDS and FORTIFY _warning_
coverage. In other words, there are no new restrictions, just
potentially new warnings. Any new FORTIFY warnings we've seen have
been fixed (usually in their respective subsystem trees). For more
details, see commit df8fc4e934c12b.
The under-development compiler attribute __counted_by has been added
so that we can start annotating flexible array members with their
associated structure member that tracks the count of flexible array
elements at run-time. It is possible (likely?) that the exact syntax
of the attribute will change before it is finalized, but GCC and Clang
are working together to sort it out. Any changes can be made to the
macro while we continue to add annotations.
As an example of that last case, I have a treewide commit waiting with
such annotations found via Coccinelle:
https://git.kernel.org/linus/adc5b3cb48a049563dc673f348eab7b6beba8a9b
Also see commit dd06e72e68bcb4 for more details.
Summary:
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex
arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members"
* tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (54 commits)
netfilter: ipset: Replace strlcpy with strscpy
uml: Replace strlcpy with strscpy
um: Use HOST_DIR for mrproper
kallsyms: Replace all non-returning strlcpy with strscpy
sh: Replace all non-returning strlcpy with strscpy
of/flattree: Replace all non-returning strlcpy with strscpy
sparc64: Replace all non-returning strlcpy with strscpy
Hexagon: Replace all non-returning strlcpy with strscpy
kobject: Use return value of strreplace()
lib/string_helpers: Change returned value of the strreplace()
jbd2: Avoid printing outside the boundary of the buffer
checkpatch: Check for 0-length and 1-element arrays
riscv/purgatory: Do not use fortified string functions
s390/purgatory: Do not use fortified string functions
x86/purgatory: Do not use fortified string functions
acpi: Replace struct acpi_table_slit 1-element array with flex-array
clocksource: Replace all non-returning strlcpy with strscpy
string: use __builtin_memcpy() in strlcpy/strlcat
staging: most: Replace all non-returning strlcpy with strscpy
drm/i2c: tda998x: Replace all non-returning strlcpy with strscpy
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux updates from Paul Moore:
- Thanks to help from the MPTCP folks, it looks like we have finally
sorted out a proper solution to the MPTCP socket labeling issue, see
the new security_mptcp_add_subflow() LSM hook.
- Fix the labeled NFS handling such that a labeled NFS share mounted
prior to the initial SELinux policy load is properly labeled once a
policy is loaded; more information in the commit description.
- Two patches to security/selinux/Makefile, the first took the cleanups
in v6.4 a bit further and the second removed the grouped targets
support as that functionality doesn't appear to be properly supported
prior to make v4.3.
- Deprecate the "fs" object context type in SELinux policies. The fs
object context type was an old vestige that was introduced back in
v2.6.12-rc2 but never really used.
- A number of small changes that remove dead code, clean up some
awkward bits, and generally improve the quality of the code. See the
individual commit descriptions for more information.
* tag 'selinux-pr-20230626' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: avoid bool as identifier name
selinux: fix Makefile for versions of make < v4.3
selinux: make labeled NFS work when mounted before policy load
selinux: cleanup exit_sel_fs() declaration
selinux: deprecated fs ocon
selinux: make header files self-including
selinux: keep context struct members in sync
selinux: Implement mptcp_add_subflow hook
security, lsm: Introduce security_mptcp_add_subflow()
selinux: small cleanups in selinux_audit_rule_init()
selinux: declare read-only data arrays const
selinux: retain const qualifier on string literal in avtab_hash_eval()
selinux: drop return at end of void function avc_insert()
selinux: avc: drop unused function avc_disable()
selinux: adjust typos in comments
selinux: do not leave dangling pointer behind
selinux: more Makefile tweaks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull ordered workqueue creation updates from Tejun Heo:
"For historical reasons, unbound workqueues with max concurrency limit
of 1 are considered ordered, even though the concurrency limit hasn't
been system-wide for a long time.
This creates ambiguity around whether ordered execution is actually
required for correctness, which was actually confusing for e.g. btrfs
(btrfs updates are being routed through the btrfs tree).
There aren't that many users in the tree which use the combination and
there are pending improvements to unbound workqueue affinity handling
which will make inadvertent use of ordered workqueue a bigger loss.
This clarifies the situation for most of them by updating the ones
which require ordered execution to use alloc_ordered_workqueue().
There are some conversions being routed through subsystem-specific
trees and likely a few stragglers. Once they're all converted,
workqueue can trigger a warning on unbound + @max_active==1 usages and
eventually drop the implicit ordered behavior"
* tag 'wq-for-6.5-cleanup-ordered' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
rxrpc: Use alloc_ordered_workqueue() to create ordered workqueues
net: qrtr: Use alloc_ordered_workqueue() to create ordered workqueues
net: wwan: t7xx: Use alloc_ordered_workqueue() to create ordered workqueues
dm integrity: Use alloc_ordered_workqueue() to create ordered workqueues
media: amphion: Use alloc_ordered_workqueue() to create ordered workqueues
scsi: NCR5380: Use default @max_active for hostdata->work_q
media: coda: Use alloc_ordered_workqueue() to create ordered workqueues
crypto: octeontx2: Use alloc_ordered_workqueue() to create ordered workqueues
wifi: ath10/11/12k: Use alloc_ordered_workqueue() to create ordered workqueues
wifi: mwifiex: Use default @max_active for workqueues
wifi: iwlwifi: Use default @max_active for trans_pcie->rba.alloc_wq
xen/pvcalls: Use alloc_ordered_workqueue() to create ordered workqueues
virt: acrn: Use alloc_ordered_workqueue() to create ordered workqueues
net: octeontx2: Use alloc_ordered_workqueue() to create ordered workqueues
net: thunderx: Use alloc_ordered_workqueue() to create ordered workqueues
greybus: Use alloc_ordered_workqueue() to create ordered workqueues
powerpc, workqueue: Use alloc_ordered_workqueue() to create ordered workqueues
|
|
Recently, our friends from bluetooth subsystem reported [1] that after
commit 5e2ff6704a27 ("scm: add SO_PASSPIDFD and SCM_PIDFD") scm_recv()
helper become unusable in kernel modules (because it uses unexported
pidfd_prepare() API).
We were aware of this issue and workarounded it in a hard way
by commit 97154bcf4d1b ("af_unix: Kconfig: make CONFIG_UNIX bool").
But recently a new functionality was added in the scope of commit
817efd3cad74 ("Bluetooth: hci_sock: Forward credentials to monitor")
and after that bluetooth can't be compiled as a kernel module.
After some discussion in [1] we decided to split scm_recv() into
two helpers, one won't support SCM_PIDFD (used for unix sockets),
and another one will be completely the same as it was before commit
5e2ff6704a27 ("scm: add SO_PASSPIDFD and SCM_PIDFD").
Link: https://lore.kernel.org/lkml/CAJqdLrpFcga4n7wxBhsFqPQiN8PKFVr6U10fKcJ9W7AcZn+o6Q@mail.gmail.com/ [1]
Fixes: 5e2ff6704a27 ("scm: add SO_PASSPIDFD and SCM_PIDFD")
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230627174314.67688-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge in late fixes to prepare for the 6.5 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported a warning in __local_bh_enable_ip(). [0]
Commit 8d61f926d420 ("netlink: fix potential deadlock in
netlink_set_err()") converted read_lock(&nl_table_lock) to
read_lock_irqsave() in __netlink_diag_dump() to prevent a deadlock.
However, __netlink_diag_dump() calls sock_i_ino() that uses
read_lock_bh() and read_unlock_bh(). If CONFIG_TRACE_IRQFLAGS=y,
read_unlock_bh() finally enables IRQ even though it should stay
disabled until the following read_unlock_irqrestore().
Using read_lock() in sock_i_ino() would trigger a lockdep splat
in another place that was fixed in commit f064af1e500a ("net: fix
a lockdep splat"), so let's add __sock_i_ino() that would be safe
to use under BH disabled.
[0]:
WARNING: CPU: 0 PID: 5012 at kernel/softirq.c:376 __local_bh_enable_ip+0xbe/0x130 kernel/softirq.c:376
Modules linked in:
CPU: 0 PID: 5012 Comm: syz-executor487 Not tainted 6.4.0-rc7-syzkaller-00202-g6f68fc395f49 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
RIP: 0010:__local_bh_enable_ip+0xbe/0x130 kernel/softirq.c:376
Code: 45 bf 01 00 00 00 e8 91 5b 0a 00 e8 3c 15 3d 00 fb 65 8b 05 ec e9 b5 7e 85 c0 74 58 5b 5d c3 65 8b 05 b2 b6 b4 7e 85 c0 75 a2 <0f> 0b eb 9e e8 89 15 3d 00 eb 9f 48 89 ef e8 6f 49 18 00 eb a8 0f
RSP: 0018:ffffc90003a1f3d0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000201 RCX: 1ffffffff1cf5996
RDX: 0000000000000000 RSI: 0000000000000201 RDI: ffffffff8805c6f3
RBP: ffffffff8805c6f3 R08: 0000000000000001 R09: ffff8880152b03a3
R10: ffffed1002a56074 R11: 0000000000000005 R12: 00000000000073e4
R13: dffffc0000000000 R14: 0000000000000002 R15: 0000000000000000
FS: 0000555556726300(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000045ad50 CR3: 000000007c646000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
sock_i_ino+0x83/0xa0 net/core/sock.c:2559
__netlink_diag_dump+0x45c/0x790 net/netlink/diag.c:171
netlink_diag_dump+0xd6/0x230 net/netlink/diag.c:207
netlink_dump+0x570/0xc50 net/netlink/af_netlink.c:2269
__netlink_dump_start+0x64b/0x910 net/netlink/af_netlink.c:2374
netlink_dump_start include/linux/netlink.h:329 [inline]
netlink_diag_handler_dump+0x1ae/0x250 net/netlink/diag.c:238
__sock_diag_cmd net/core/sock_diag.c:238 [inline]
sock_diag_rcv_msg+0x31e/0x440 net/core/sock_diag.c:269
netlink_rcv_skb+0x165/0x440 net/netlink/af_netlink.c:2547
sock_diag_rcv+0x2a/0x40 net/core/sock_diag.c:280
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x547/0x7f0 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x925/0xe30 net/netlink/af_netlink.c:1914
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0xde/0x190 net/socket.c:747
____sys_sendmsg+0x71c/0x900 net/socket.c:2503
___sys_sendmsg+0x110/0x1b0 net/socket.c:2557
__sys_sendmsg+0xf7/0x1c0 net/socket.c:2586
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f5303aaabb9
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffc7506e548 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5303aaabb9
RDX: 0000000000000000 RSI: 0000000020000180 RDI: 0000000000000003
RBP: 00007f5303a6ed60 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f5303a6edf0
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Fixes: 8d61f926d420 ("netlink: fix potential deadlock in netlink_set_err()")
Reported-by: syzbot+5da61cf6a9bc1902d422@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=5da61cf6a9bc1902d422
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230626164313.52528-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When using the felix driver (the only one which supports UC filtering
and MC filtering) as a DSA master for a random other DSA switch, one can
see the following stack trace when the downstream switch ports join a
VLAN-aware bridge:
=============================
WARNING: suspicious RCU usage
-----------------------------
net/8021q/vlan_core.c:238 suspicious rcu_dereference_protected() usage!
stack backtrace:
Workqueue: dsa_ordered dsa_slave_switchdev_event_work
Call trace:
lockdep_rcu_suspicious+0x170/0x210
vlan_for_each+0x8c/0x188
dsa_slave_sync_uc+0x128/0x178
__hw_addr_sync_dev+0x138/0x158
dsa_slave_set_rx_mode+0x58/0x70
__dev_set_rx_mode+0x88/0xa8
dev_uc_add+0x74/0xa0
dsa_port_bridge_host_fdb_add+0xec/0x180
dsa_slave_switchdev_event_work+0x7c/0x1c8
process_one_work+0x290/0x568
What it's saying is that vlan_for_each() expects rtnl_lock() context and
it's not getting it, when it's called from the DSA master's ndo_set_rx_mode().
The caller of that - dsa_slave_set_rx_mode() - is the slave DSA
interface's dsa_port_bridge_host_fdb_add() which comes from the deferred
dsa_slave_switchdev_event_work().
We went to great lengths to avoid the rtnl_lock() context in that call
path in commit 0faf890fc519 ("net: dsa: drop rtnl_lock from
dsa_slave_switchdev_event_work"), and calling rtnl_lock() is simply not
an option due to the possibility of deadlocking when calling
dsa_flush_workqueue() from the call paths that do hold rtnl_lock() -
basically all of them.
So, when the DSA master calls vlan_for_each() from its ndo_set_rx_mode(),
the state of the 8021q driver on this device is really not protected
from concurrent access by anything.
Looking at net/8021q/, I don't think that vlan_info->vid_list was
particularly designed with RCU traversal in mind, so introducing an RCU
read-side form of vlan_for_each() - vlan_for_each_rcu() - won't be so
easy, and it also wouldn't be exactly what we need anyway.
In general I believe that the solution isn't in net/8021q/ anyway;
vlan_for_each() is not cut out for this task. DSA doesn't need rtnl_lock()
to be held per se - since it's not a netdev state change that we're
blocking, but rather, just concurrent additions/removals to a VLAN list.
We don't even need sleepable context - the callback of vlan_for_each()
just schedules deferred work.
The proposed escape is to remove the dependency on vlan_for_each() and
to open-code a non-sleepable, rtnl-free alternative to that, based on
copies of the VLAN list modified from .ndo_vlan_rx_add_vid() and
.ndo_vlan_rx_kill_vid().
Fixes: 64fdc5f341db ("net: dsa: sync unicast and multicast addresses for VLAN filters too")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230626154402.3154454-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 3f5f118bb657f94641ea383c7c1b8c09a5d46ea2.
Konrad reported that desktop environment below cannot be reached after
commit 3f5f118bb657 ("af_unix: Call scm_recv() only after scm_set_cred().")
- postmarketOS (Alpine Linux w/ musl 1.2.4)
- busybox 1.36.1
- GNOME 44.1
- networkmanager 1.42.6
- openrc 0.47
Regarding to the warning of SO_PASSPIDFD, I'll post another patch to
suppress it by skipping SCM_PIDFD if scm->pid == NULL in scm_pidfd_recv().
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/netdev/8c7f9abd-4f84-7296-2788-1e130d6304a0@kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20230626205837.82086-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the mishandling of MSG_DONTWAIT and also reinstates the per-page
checking of the source pages (which might have come from a DIO write by
userspace) by partially reverting the changes to support MSG_SPLICE_PAGES
and doing things a little differently. In messenger_v1:
(1) The ceph_tcp_sendpage() is resurrected and the callers reverted to use
that.
(2) The callers now pass MSG_MORE unconditionally. Previously, they were
passing in MSG_MORE|MSG_SENDPAGE_NOTLAST and then degrading that to
just MSG_MORE on the last call to ->sendpage().
(3) Make ceph_tcp_sendpage() a wrapper around sendmsg() rather than
sendpage(), setting MSG_SPLICE_PAGES if sendpage_ok() returns true on
the page.
In messenger_v2:
(4) Bring back do_try_sendpage() and make the callers use that.
(5) Make do_try_sendpage() use sendmsg() for both cases and set
MSG_SPLICE_PAGES if sendpage_ok() is set.
Fixes: 40a8c17aa770 ("ceph: Use sendmsg(MSG_SPLICE_PAGES) rather than sendpage")
Fixes: fa094ccae1e7 ("ceph: Use sendmsg(MSG_SPLICE_PAGES) rather than sendpage()")
Reported-by: Ilya Dryomov <idryomov@gmail.com>
Link: https://lore.kernel.org/r/CAOi1vP9vjLfk3W+AJFeexC93jqPaPUn2dD_4NrzxwoZTbYfOnw@mail.gmail.com/
Link: https://lore.kernel.org/r/CAOi1vP_Bn918j24S94MuGyn+Gxk212btw7yWeDrRcW1U8pc_BA@mail.gmail.com/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Xiubo Li <xiubli@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Link: https://lore.kernel.org/r/3101881.1687801973@warthog.procyon.org.uk/ # v1
Link: https://lore.kernel.org/r/3111635.1687813501@warthog.procyon.org.uk/ # v2
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Link: https://lore.kernel.org/r/3199652.1687873788@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
1) Allow slightly larger IPVS connection table size from Kconfig for
64-bit arch, from Abhijeet Rastogi.
2) Since IPVS connection table might be larger than 2^20 after previous
patch, allow to limit it depending on the available memory.
Moreover, use kvmalloc. From Julian Anastasov.
3) Do not rebuild VLAN header in nft_payload when matching source and
destination MAC address.
4) Remove nested rcu read lock side in ip_set_test(), from Florian Westphal.
5) Allow to update set size, also from Florian.
6) Improve NAT tuple selection when connection is closing,
from Florian Westphal.
7) Support for resetting set element stateful expression, from Phil Sutter.
8) Use NLA_POLICY_MAX to narrow down maximum attribute value in nf_tables,
from Florian Westphal.
* tag 'nf-next-23-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_tables: limit allowed range via nla_policy
netfilter: nf_tables: Introduce NFT_MSG_GETSETELEM_RESET
netfilter: snat: evict closing tcp entries on reply tuple collision
netfilter: nf_tables: permit update of set size
netfilter: ipset: remove rcu_read_lock_bh pair from ip_set_test
netfilter: nft_payload: rebuild vlan header when needed
ipvs: dynamically limit the connection hash table
ipvs: increase ip_vs_conn_tab_bits range for 64BIT
====================
Link: https://lore.kernel.org/r/20230626064749.75525-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull io_uring updates from Jens Axboe:
"Nothing major in this release, just a bunch of cleanups and some
optimizations around networking mostly.
- clean up file request flags handling (Christoph)
- clean up request freeing and CQ locking (Pavel)
- support for using pre-registering the io_uring fd at setup time
(Josh)
- Add support for user allocated ring memory, rather than having the
kernel allocate it. Mostly for packing rings into a huge page (me)
- avoid an unnecessary double retry on receive (me)
- maintain ordering for task_work, which also improves performance
(me)
- misc cleanups/fixes (Pavel, me)"
* tag 'for-6.5/io_uring-2023-06-23' of git://git.kernel.dk/linux: (39 commits)
io_uring: merge conditional unlock flush helpers
io_uring: make io_cq_unlock_post static
io_uring: inline __io_cq_unlock
io_uring: fix acquire/release annotations
io_uring: kill io_cq_unlock()
io_uring: remove IOU_F_TWQ_FORCE_NORMAL
io_uring: don't batch task put on reqs free
io_uring: move io_clean_op()
io_uring: inline io_dismantle_req()
io_uring: remove io_free_req_tw
io_uring: open code io_put_req_find_next
io_uring: add helpers to decode the fixed file file_ptr
io_uring: use io_file_from_index in io_msg_grab_file
io_uring: use io_file_from_index in __io_sync_cancel
io_uring: return REQ_F_ flags from io_file_get_flags
io_uring: remove io_req_ffs_set
io_uring: remove a confusing comment above io_file_get_flags
io_uring: remove the mode variable in io_file_get_flags
io_uring: remove __io_file_supports_nowait
io_uring: wait interruptibly for request completions on exit
...
|
|
Pull splice updates from Jens Axboe:
"This kills off ITER_PIPE to avoid a race between truncate,
iov_iter_revert() on the pipe and an as-yet incomplete DMA to a bio
with unpinned/unref'ed pages from an O_DIRECT splice read. This causes
memory corruption.
Instead, we either use (a) filemap_splice_read(), which invokes the
buffered file reading code and splices from the pagecache into the
pipe; (b) copy_splice_read(), which bulk-allocates a buffer, reads
into it and then pushes the filled pages into the pipe; or (c) handle
it in filesystem-specific code.
Summary:
- Rename direct_splice_read() to copy_splice_read()
- Simplify the calculations for the number of pages to be reclaimed
in copy_splice_read()
- Turn do_splice_to() into a helper, vfs_splice_read(), so that it
can be used by overlayfs and coda to perform the checks on the
lower fs
- Make vfs_splice_read() jump to copy_splice_read() to handle
direct-I/O and DAX
- Provide shmem with its own splice_read to handle non-existent pages
in the pagecache. We don't want a ->read_folio() as we don't want
to populate holes, but filemap_get_pages() requires it
- Provide overlayfs with its own splice_read to call down to a lower
layer as overlayfs doesn't provide ->read_folio()
- Provide coda with its own splice_read to call down to a lower layer
as coda doesn't provide ->read_folio()
- Direct ->splice_read to copy_splice_read() in tty, procfs, kernfs
and random files as they just copy to the output buffer and don't
splice pages
- Provide wrappers for afs, ceph, ecryptfs, ext4, f2fs, nfs, ntfs3,
ocfs2, orangefs, xfs and zonefs to do locking and/or revalidation
- Make cifs use filemap_splice_read()
- Replace pointers to generic_file_splice_read() with pointers to
filemap_splice_read() as DIO and DAX are handled in the caller;
filesystems can still provide their own alternate ->splice_read()
op
- Remove generic_file_splice_read()
- Remove ITER_PIPE and its paraphernalia as generic_file_splice_read
was the only user"
* tag 'for-6.5/splice-2023-06-23' of git://git.kernel.dk/linux: (31 commits)
splice: kdoc for filemap_splice_read() and copy_splice_read()
iov_iter: Kill ITER_PIPE
splice: Remove generic_file_splice_read()
splice: Use filemap_splice_read() instead of generic_file_splice_read()
cifs: Use filemap_splice_read()
trace: Convert trace/seq to use copy_splice_read()
zonefs: Provide a splice-read wrapper
xfs: Provide a splice-read wrapper
orangefs: Provide a splice-read wrapper
ocfs2: Provide a splice-read wrapper
ntfs3: Provide a splice-read wrapper
nfs: Provide a splice-read wrapper
f2fs: Provide a splice-read wrapper
ext4: Provide a splice-read wrapper
ecryptfs: Provide a splice-read wrapper
ceph: Provide a splice-read wrapper
afs: Provide a splice-read wrapper
9p: Add splice_read wrapper
net: Make sock_splice_read() use copy_splice_read() by default
tty, proc, kernfs, random: Use copy_splice_read()
...
|
|
Pull nfsd updates from Chuck Lever:
- Clean-ups in the READ path in anticipation of MSG_SPLICE_PAGES
- Better NUMA awareness when allocating pages and other objects
- A number of minor clean-ups to XDR encoding
- Elimination of a race when accepting a TCP socket
- Numerous observability enhancements
* tag 'nfsd-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux: (46 commits)
nfsd: remove redundant assignments to variable len
svcrdma: Fix stale comment
NFSD: Distinguish per-net namespace initialization
nfsd: move init of percpu reply_cache_stats counters back to nfsd_init_net
SUNRPC: Address RCU warning in net/sunrpc/svc.c
SUNRPC: Use sysfs_emit in place of strlcpy/sprintf
SUNRPC: Remove transport class dprintk call sites
SUNRPC: Fix comments for transport class registration
svcrdma: Remove an unused argument from __svc_rdma_put_rw_ctxt()
svcrdma: trace cc_release calls
svcrdma: Convert "might sleep" comment into a code annotation
NFSD: Add an nfsd4_encode_nfstime4() helper
SUNRPC: Move initialization of rq_stime
SUNRPC: Optimize page release in svc_rdma_sendto()
svcrdma: Prevent page release when nothing was received
svcrdma: Revert 2a1e4f21d841 ("svcrdma: Normalize Send page handling")
SUNRPC: Revert 579900670ac7 ("svcrdma: Remove unused sc_pages field")
SUNRPC: Revert cc93ce9529a6 ("svcrdma: Retain the page backing rq_res.head[0].iov_base")
NFSD: add encoding of op_recall flag for write delegation
NFSD: Add "official" reviewers for this subsystem
...
|
|
Set element addition error path decrements reference counter on chains
twice: once on element release and again via nft_data_release().
Then, d6b478666ffa ("netfilter: nf_tables: fix underflow in object
reference counter") incorrectly fixed this by removing the stateful
object reference count decrement.
Restore the stateful object decrement as in b91d90368837 ("netfilter:
nf_tables: fix leaking object reference count") and let
nft_data_release() decrement the chain reference counter, so this is
done only once.
Fixes: d6b478666ffa ("netfilter: nf_tables: fix underflow in object reference counter")
Fixes: 628bd3e49cba ("netfilter: nf_tables: drop map element references from preparation phase")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Otherwise a dangling reference to a rule object that is gone remains
in the set binding list.
Fixes: 26b5a5712eb8 ("netfilter: nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
value.
ct_sip_parse_numerical_param() returns only 0 or 1 now.
But process_register_request() and process_register_response() imply
checking for a negative value if parsing of a numerical header parameter
failed.
The invocation in nf_nat_sip() looks correct:
if (ct_sip_parse_numerical_param(...) > 0 &&
...) { ... }
Make the return value of the function ct_sip_parse_numerical_param()
a tristate to fix all the cases
a) return 1 if value is found; *val is set
b) return 0 if value is not found; *val is unchanged
c) return -1 on error; *val is undefined
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: 0f32a40fc91a ("[NETFILTER]: nf_conntrack_sip: create signalling expectations")
Signed-off-by: Ilia.Gavrilov <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
basic one
Eric Dumazet says:
nf_conntrack_dccp_packet() has an unique:
dh = skb_header_pointer(skb, dataoff, sizeof(_dh), &_dh);
And nothing more is 'pulled' from the packet, depending on the content.
dh->dccph_doff, and/or dh->dccph_x ...)
So dccp_ack_seq() is happily reading stuff past the _dh buffer.
BUG: KASAN: stack-out-of-bounds in nf_conntrack_dccp_packet+0x1134/0x11c0
Read of size 4 at addr ffff000128f66e0c by task syz-executor.2/29371
[..]
Fix this by increasing the stack buffer to also include room for
the extra sequence numbers and all the known dccp packet type headers,
then pull again after the initial validation of the basic header.
While at it, mark packets invalid that lack 48bit sequence bit but
where RFC says the type MUST use them.
Compile tested only.
v2: first skb_header_pointer() now needs to adjust the size to
only pull the generic header. (Eric)
Heads-up: I intend to remove dccp conntrack support later this year.
Fixes: 2bc780499aa3 ("[NETFILTER]: nf_conntrack: add DCCP protocol support")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This commit fixes several use-after-free that caused by function
nfc_llcp_find_local(). For example, one UAF can happen when below buggy
time window occurs.
// nfc_genl_llc_get_params | // nfc_unregister_device
|
dev = nfc_get_device(idx); | device_lock(...)
if (!dev) | dev->shutting_down = true;
return -ENODEV; | device_unlock(...);
|
device_lock(...); | // nfc_llcp_unregister_device
| nfc_llcp_find_local()
nfc_llcp_find_local(...); |
| local_cleanup()
if (!local) { |
rc = -ENODEV; | // nfc_llcp_local_put
goto exit; | kref_put(.., local_release)
} |
| // local_release
| list_del(&local->list)
// nfc_genl_send_params | kfree()
local->dev->idx !!!UAF!!! |
|
and the crash trace for the one of the discussed UAF like:
BUG: KASAN: slab-use-after-free in nfc_genl_llc_get_params+0x72f/0x780 net/nfc/netlink.c:1045
Read of size 8 at addr ffff888105b0e410 by task 20114
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x72/0xa0 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:319 [inline]
print_report+0xcc/0x620 mm/kasan/report.c:430
kasan_report+0xb2/0xe0 mm/kasan/report.c:536
nfc_genl_send_params net/nfc/netlink.c:999 [inline]
nfc_genl_llc_get_params+0x72f/0x780 net/nfc/netlink.c:1045
genl_family_rcv_msg_doit.isra.0+0x1ee/0x2e0 net/netlink/genetlink.c:968
genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline]
genl_rcv_msg+0x503/0x7d0 net/netlink/genetlink.c:1065
netlink_rcv_skb+0x161/0x430 net/netlink/af_netlink.c:2548
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x644/0x900 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x934/0xe70 net/netlink/af_netlink.c:1913
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0x1b6/0x200 net/socket.c:747
____sys_sendmsg+0x6e9/0x890 net/socket.c:2501
___sys_sendmsg+0x110/0x1b0 net/socket.c:2555
__sys_sendmsg+0xf7/0x1d0 net/socket.c:2584
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7f34640a2389
RSP: 002b:00007f3463415168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f34641c1f80 RCX: 00007f34640a2389
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000006
RBP: 00007f34640ed493 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffe38449ecf R14: 00007f3463415300 R15: 0000000000022000
</TASK>
Allocated by task 20116:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
____kasan_kmalloc mm/kasan/common.c:374 [inline]
__kasan_kmalloc+0x7f/0x90 mm/kasan/common.c:383
kmalloc include/linux/slab.h:580 [inline]
kzalloc include/linux/slab.h:720 [inline]
nfc_llcp_register_device+0x49/0xa40 net/nfc/llcp_core.c:1567
nfc_register_device+0x61/0x260 net/nfc/core.c:1124
nci_register_device+0x776/0xb20 net/nfc/nci/core.c:1257
virtual_ncidev_open+0x147/0x230 drivers/nfc/virtual_ncidev.c:148
misc_open+0x379/0x4a0 drivers/char/misc.c:165
chrdev_open+0x26c/0x780 fs/char_dev.c:414
do_dentry_open+0x6c4/0x12a0 fs/open.c:920
do_open fs/namei.c:3560 [inline]
path_openat+0x24fe/0x37e0 fs/namei.c:3715
do_filp_open+0x1ba/0x410 fs/namei.c:3742
do_sys_openat2+0x171/0x4c0 fs/open.c:1356
do_sys_open fs/open.c:1372 [inline]
__do_sys_openat fs/open.c:1388 [inline]
__se_sys_openat fs/open.c:1383 [inline]
__x64_sys_openat+0x143/0x200 fs/open.c:1383
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 20115:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
kasan_save_free_info+0x2e/0x50 mm/kasan/generic.c:521
____kasan_slab_free mm/kasan/common.c:236 [inline]
____kasan_slab_free mm/kasan/common.c:200 [inline]
__kasan_slab_free+0x10a/0x190 mm/kasan/common.c:244
kasan_slab_free include/linux/kasan.h:162 [inline]
slab_free_hook mm/slub.c:1781 [inline]
slab_free_freelist_hook mm/slub.c:1807 [inline]
slab_free mm/slub.c:3787 [inline]
__kmem_cache_free+0x7a/0x190 mm/slub.c:3800
local_release net/nfc/llcp_core.c:174 [inline]
kref_put include/linux/kref.h:65 [inline]
nfc_llcp_local_put net/nfc/llcp_core.c:182 [inline]
nfc_llcp_local_put net/nfc/llcp_core.c:177 [inline]
nfc_llcp_unregister_device+0x206/0x290 net/nfc/llcp_core.c:1620
nfc_unregister_device+0x160/0x1d0 net/nfc/core.c:1179
virtual_ncidev_close+0x52/0xa0 drivers/nfc/virtual_ncidev.c:163
__fput+0x252/0xa20 fs/file_table.c:321
task_work_run+0x174/0x270 kernel/task_work.c:179
resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
exit_to_user_mode_prepare+0x108/0x110 kernel/entry/common.c:204
__syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
syscall_exit_to_user_mode+0x21/0x50 kernel/entry/common.c:297
do_syscall_64+0x4c/0x90 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Last potentially related work creation:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
__kasan_record_aux_stack+0x95/0xb0 mm/kasan/generic.c:491
kvfree_call_rcu+0x29/0xa80 kernel/rcu/tree.c:3328
drop_sysctl_table+0x3be/0x4e0 fs/proc/proc_sysctl.c:1735
unregister_sysctl_table.part.0+0x9c/0x190 fs/proc/proc_sysctl.c:1773
unregister_sysctl_table+0x24/0x30 fs/proc/proc_sysctl.c:1753
neigh_sysctl_unregister+0x5f/0x80 net/core/neighbour.c:3895
addrconf_notify+0x140/0x17b0 net/ipv6/addrconf.c:3684
notifier_call_chain+0xbe/0x210 kernel/notifier.c:87
call_netdevice_notifiers_info+0xb5/0x150 net/core/dev.c:1937
call_netdevice_notifiers_extack net/core/dev.c:1975 [inline]
call_netdevice_notifiers net/core/dev.c:1989 [inline]
dev_change_name+0x3c3/0x870 net/core/dev.c:1211
dev_ifsioc+0x800/0xf70 net/core/dev_ioctl.c:376
dev_ioctl+0x3d9/0xf80 net/core/dev_ioctl.c:542
sock_do_ioctl+0x160/0x260 net/socket.c:1213
sock_ioctl+0x3f9/0x670 net/socket.c:1316
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x19e/0x210 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
The buggy address belongs to the object at ffff888105b0e400
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 16 bytes inside of
freed 1024-byte region [ffff888105b0e400, ffff888105b0e800)
The buggy address belongs to the physical page:
head:ffffea000416c200 order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffff8881000430c0 ffffea00044c7010 ffffea0004510e10
raw: 0000000000000000 00000000000a000a 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888105b0e300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888105b0e380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff888105b0e400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888105b0e480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888105b0e500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
In summary, this patch solves those use-after-free by
1. Re-implement the nfc_llcp_find_local(). The current version does not
grab the reference when getting the local from the linked list. For
example, the llcp_sock_bind() gets the reference like below:
// llcp_sock_bind()
local = nfc_llcp_find_local(dev); // A
..... \
| raceable
..... /
llcp_sock->local = nfc_llcp_local_get(local); // B
There is an apparent race window that one can drop the reference
and free the local object fetched in (A) before (B) gets the reference.
2. Some callers of the nfc_llcp_find_local() do not grab the reference
at all. For example, the nfc_genl_llc_{{get/set}_params/sdreq} functions.
We add the nfc_llcp_local_put() for them. Moreover, we add the necessary
error handling function to put the reference.
3. Add the nfc_llcp_remove_local() helper. The local object is removed
from the linked list in local_release() when all reference is gone. This
patch removes it when nfc_llcp_unregister_device() is called.
Therefore, every caller of nfc_llcp_find_local() will get a reference
even when the nfc_llcp_unregister_device() is called. This promises no
use-after-free for the local object is ever possible.
Fixes: 52feb444a903 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support")
Fixes: c7aa12252f51 ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These NLA_U32 types get stored in u8 fields, reject invalid values
instead of silently casting to u8.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
