Age | Commit message (Collapse) | Author | Files | Lines |
|
Use correct HCI ISO data packet header struct when the packet has
timestamp. The timestamp, when present, goes before the other fields
(Core v5.3 4E 5.4.5), so the structs are not compatible.
Fixes: ccf74f2390d6 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Because some transports don't have a dedicated type for ISO packets
(see 14202eff214e1e941fefa0366d4c3bc4b1a0d500) they may use ACL type
when in fact they are ISO packets.
In the past this was left for the driver to detect such thing but it
creates a problem when using the likes of btproxy when used by a VM as
the host would not be aware of the connection the guest is doing it
won't be able to detect such behavior, so this make bt_recv_frame
detect when it happens as it is the common interface to all drivers
including guest VMs.
Fixes: 14202eff214e ("Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packet")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The address resolution should be disabled during the active scan,
so all the advertisements can reach the host. The advertising
has to be paused before disabling the address resolution,
because the advertising will prevent any changes to the resolving
list and the address resolution status. Skipping this will cause
the hci error and the discovery failure.
According to the bluetooth specification:
"7.8.44 LE Set Address Resolution Enable command
This command shall not be used when:
- Advertising (other than periodic advertising) is enabled,
- Scanning is enabled, or
- an HCI_LE_Create_Connection, HCI_LE_Extended_Create_Connection, or
HCI_LE_Periodic_Advertising_Create_Sync command is outstanding."
If the host is using RPA, the controller needs to generate RPA for
the advertising, so the advertising must remain paused during the
active scan.
If the host is not using RPA, the advertising can be resumed after
disabling the address resolution.
Fixes: 9afc675edeeb ("Bluetooth: hci_sync: allow advertise when scan without RPA")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Drivers should not assume skb_mac_header(skb) == skb->data in their
ndo_start_xmit().
Use skb_network_offset() and skb_transport_offset() which
better describe what is needed in erspan_fb_xmit() and
ip6erspan_tunnel_xmit()
syzbot reported:
WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 skb_mac_header include/linux/skbuff.h:2873 [inline]
WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962
Modules linked in:
CPU: 0 PID: 5083 Comm: syz-executor406 Not tainted 6.3.0-rc2-syzkaller-00866-gd4671cb96fa3 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023
RIP: 0010:skb_mac_header include/linux/skbuff.h:2873 [inline]
RIP: 0010:ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962
Code: 04 02 41 01 de 84 c0 74 08 3c 03 0f 8e 1c 0a 00 00 45 89 b4 24 c8 00 00 00 c6 85 77 fe ff ff 01 e9 33 e7 ff ff e8 b4 27 a1 f8 <0f> 0b e9 b6 e7 ff ff e8 a8 27 a1 f8 49 8d bf f0 0c 00 00 48 b8 00
RSP: 0018:ffffc90003b2f830 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 000000000000ffff RCX: 0000000000000000
RDX: ffff888021273a80 RSI: ffffffff88e1bd4c RDI: 0000000000000003
RBP: ffffc90003b2f9d8 R08: 0000000000000003 R09: 000000000000ffff
R10: 000000000000ffff R11: 0000000000000000 R12: ffff88802b28da00
R13: 00000000000000d0 R14: ffff88807e25b6d0 R15: ffff888023408000
FS: 0000555556a61300(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055e5b11eb6e8 CR3: 0000000027c1b000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__netdev_start_xmit include/linux/netdevice.h:4900 [inline]
netdev_start_xmit include/linux/netdevice.h:4914 [inline]
__dev_direct_xmit+0x504/0x730 net/core/dev.c:4300
dev_direct_xmit include/linux/netdevice.h:3088 [inline]
packet_xmit+0x20a/0x390 net/packet/af_packet.c:285
packet_snd net/packet/af_packet.c:3075 [inline]
packet_sendmsg+0x31a0/0x5150 net/packet/af_packet.c:3107
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0xde/0x190 net/socket.c:747
__sys_sendto+0x23a/0x340 net/socket.c:2142
__do_sys_sendto net/socket.c:2154 [inline]
__se_sys_sendto net/socket.c:2150 [inline]
__x64_sys_sendto+0xe1/0x1b0 net/socket.c:2150
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f123aaa1039
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 b1 14 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffc15d12058 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f123aaa1039
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000020000040 R09: 0000000000000014
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f123aa648c0
R13: 431bde82d7b634db R14: 0000000000000000 R15: 0000000000000000
Fixes: 1baf5ebf8954 ("erspan: auto detect truncated packets.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230320163427.8096-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When BCM63xx internal switches are connected to switches with a 4-byte
Broadcom tag, it does not identify the packet as VLAN tagged, so it adds one
based on its PVID (which is likely 0).
Right now, the packet is received by the BCM63xx internal switch and the 6-byte
tag is properly processed. The next step would to decode the corresponding
4-byte tag. However, the internal switch adds an invalid VLAN tag after the
6-byte tag and the 4-byte tag handling fails.
In order to fix this we need to remove the invalid VLAN tag after the 6-byte
tag before passing it to the 4-byte tag decoding.
Fixes: 964dbf186eaa ("net: dsa: tag_brcm: add support for legacy tags")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230319095540.239064-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We collect the software statistics counters for RX bytes (reported to
/proc/net/dev and to ethtool -S $dev | grep 'rx_bytes: ") at a time when
skb->len has already been adjusted by the eth_type_trans() ->
skb_pull_inline(skb, ETH_HLEN) call to exclude the L2 header.
This means that when connecting 2 DSA interfaces back to back and
sending 1 packet with length 100, the sending interface will report
tx_bytes as incrementing by 100, and the receiving interface will report
rx_bytes as incrementing by 86.
Since accounting for that in scripts is quirky and is something that
would be DSA-specific behavior (requiring users to know that they are
running on a DSA interface in the first place), the proposal is that we
treat it as a bug and fix it.
This design bug has always existed in DSA, according to my analysis:
commit 91da11f870f0 ("net: Distributed Switch Architecture protocol
support") also updates skb->dev->stats.rx_bytes += skb->len after the
eth_type_trans() call. Technically, prior to Florian's commit
a86d8becc3f0 ("net: dsa: Factor bottom tag receive functions"), each and
every vendor-specific tagging protocol driver open-coded the same bug,
until the buggy code was consolidated into something resembling what can
be seen now. So each and every driver should have its own Fixes: tag,
because of their different histories until the convergence point.
I'm not going to do that, for the sake of simplicity, but just blame the
oldest appearance of buggy code.
There are 2 ways to fix the problem. One is the obvious way, and the
other is how I ended up doing it. Obvious would have been to move
dev_sw_netstats_rx_add() one line above eth_type_trans(), and below
skb_push(skb, ETH_HLEN). But DSA processing is not as simple as that.
We count the bytes after removing everything DSA-related from the
packet, to emulate what the packet's length was, on the wire, when the
user port received it.
When eth_type_trans() executes, dsa_untag_bridge_pvid() has not run yet,
so in case the switch driver requests this behavior - commit
412a1526d067 ("net: dsa: untag the bridge pvid from rx skbs") has the
details - the obvious variant of the fix wouldn't have worked, because
the positioning there would have also counted the not-yet-stripped VLAN
header length, something which is absent from the packet as seen on the
wire (there it may be untagged, whereas software will see it as
PVID-tagged).
Fixes: f613ed665bb3 ("net: dsa: Add support for 64-bit statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, wifi and ipsec.
A little more changes than usual, but it's pretty normal for us that
the rc3/rc4 PRs are oversized as people start testing in earnest.
Possibly an extra boost from people deploying the 6.1 LTS but that's
more of an unscientific hunch.
Current release - regressions:
- phy: mscc: fix deadlock in phy_ethtool_{get,set}_wol()
- virtio: vsock: don't use skbuff state to account credit
- virtio: vsock: don't drop skbuff on copy failure
- virtio_net: fix page_to_skb() miscalculating the memory size
Current release - new code bugs:
- eth: correct xdp_features after device reconfig
- wifi: nl80211: fix the puncturing bitmap policy
- net/mlx5e: flower:
- fix raw counter initialization
- fix missing error code
- fix cloned flow attribute
- ipa:
- fix some register validity checks
- fix a surprising number of bad offsets
- kill FILT_ROUT_CACHE_CFG IPA register
Previous releases - regressions:
- tcp: fix bind() conflict check for dual-stack wildcard address
- veth: fix use after free in XDP_REDIRECT when skb headroom is small
- ipv4: fix incorrect table ID in IOCTL path
- ipvlan: make skb->skb_iif track skb->dev for l3s mode
- mptcp:
- fix possible deadlock in subflow_error_report
- fix UaFs when destroying unaccepted and listening sockets
- dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290
Previous releases - always broken:
- tcp: tcp_make_synack() can be called from process context, don't
assume preemption is disabled when updating stats
- netfilter: correct length for loading protocol registers
- virtio_net: add checking sq is full inside xdp xmit
- bonding: restore IFF_MASTER/SLAVE flags on bond enslave Ethertype
change
- phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit number
- eth: i40e: fix crash during reboot when adapter is in recovery mode
- eth: ice: avoid deadlock on rtnl lock when auxiliary device
plug/unplug meets bonding
- dsa: mt7530:
- remove now incorrect comment regarding port 5
- set PLL frequency and trgmii only when trgmii is used
- eth: mtk_eth_soc: reset PCS state when changing interface types
Misc:
- ynl: another license adjustment
- move the TCA_EXT_WARN_MSG attribute for tc action"
* tag 'net-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
selftests: bonding: add tests for ether type changes
bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails
bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change
net: renesas: rswitch: Fix GWTSDIE register handling
net: renesas: rswitch: Fix the output value of quote from rswitch_rx()
ethernet: sun: add check for the mdesc_grab()
net: ipa: fix some register validity checks
net: ipa: kill FILT_ROUT_CACHE_CFG IPA register
net: ipa: add two missing declarations
net: ipa: reg: include <linux/bug.h>
net: xdp: don't call notifiers during driver init
net/sched: act_api: add specific EXT_WARN_MSG for tc action
Revert "net/sched: act_api: move TCA_EXT_WARN_MSG to the correct hierarchy"
net: dsa: microchip: fix RGMII delay configuration on KSZ8765/KSZ8794/KSZ8795
ynl: make the tooling check the license
ynl: broaden the license even more
tools: ynl: make definitions optional again
hsr: ratelimit only when errors are printed
qed/qed_mng_tlv: correctly zero out ->min instead of ->hour
selftests: net: devlink_port_split.py: skip test if no suitable device available
...
|
|
Drivers will commonly perform feature setting during init, if they use
the xdp_set_features_flag() helper they'll likely run into an ASSERT_RTNL()
inside call_netdevice_notifiers_info().
Don't call the notifier until the device is actually registered.
Nothing should be tracking the device until its registered and
after its unregistration has started.
Fixes: 4d5ab0ad964d ("net/mlx5e: take into account device reconfiguration for xdp_features flag")
Link: https://lore.kernel.org/r/20230316220234.598091-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In my previous commit 0349b8779cc9 ("sched: add new attr TCA_EXT_WARN_MSG
to report tc extact message") I didn't notice the tc action use different
enum with filter. So we can't use TCA_EXT_WARN_MSG directly for tc action.
Let's add a TCA_ROOT_EXT_WARN_MSG for tc action specifically and put this
param before going to the TCA_ACT_TAB nest.
Fixes: 0349b8779cc9 ("sched: add new attr TCA_EXT_WARN_MSG to report tc extact message")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 923b2e30dc9cd05931da0f64e2e23d040865c035.
This is not a correct fix as TCA_EXT_WARN_MSG is not a hierarchy to
TCA_ACT_TAB. I didn't notice the TC actions use different enum when adding
TCA_EXT_WARN_MSG. To fix the difference I will add a new WARN enum in
TCA_ROOT_MAX as Jamal suggested.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I relicensed Netlink spec code to GPL-2.0 OR BSD-3-Clause but
we still put a slightly different license on the uAPI header
than the rest of the code. Use the Linux-syscall-note on all
the specs and all generated code. It's moot for kernel code,
but should not hurt. This way the licenses match everywhere.
Cc: Chuck Lever <chuck.lever@oracle.com>
Fixes: 37d9df224d1e ("ynl: re-license uniformly under GPL-2.0 OR BSD-3-Clause")
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recently, when automatically merging -net and net-next in MPTCP devel
tree, our CI reported [1] a conflict in hsr, the same as the one
reported by Stephen in netdev [2].
When looking at the conflict, I noticed it is in fact the v1 [3] that
has been applied in -net and the v2 [4] in net-next. Maybe the v1 was
applied by accident.
As mentioned by Jakub Kicinski [5], the new condition makes more sense
before the net_ratelimit(), not to update net_ratelimit's state which is
unnecessary if we're not going to print either way.
Here, this modification applies the v2 but in -net.
Link: https://github.com/multipath-tcp/mptcp_net-next/actions/runs/4423171069 [1]
Link: https://lore.kernel.org/netdev/20230315100914.53fc1760@canb.auug.org.au/ [2]
Link: https://lore.kernel.org/netdev/20230307133229.127442-1-koverskeid@gmail.com/ [3]
Link: https://lore.kernel.org/netdev/20230309092302.179586-1-koverskeid@gmail.com/ [4]
Link: https://lore.kernel.org/netdev/20230308232001.2fb62013@kernel.org/ [5]
Fixes: 28e8cabe80f3 ("net: hsr: Don't log netdev_err message on unknown prp dst node")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230315-net-20230315-hsr_framereg-ratelimit-v1-1-61d2ef176d11@tessares.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
iucv_irq_data needs to be 4 bytes larger.
These bytes are not used by the iucv module, but written by
the z/VM hypervisor in case a CPU is deconfigured.
Reported as:
BUG dma-kmalloc-64 (Not tainted): kmalloc Redzone overwritten
-----------------------------------------------------------------------------
0x0000000000400564-0x0000000000400567 @offset=1380. First byte 0x80 instead of 0xcc
Allocated in iucv_cpu_prepare+0x44/0xd0 age=167839 cpu=2 pid=1
__kmem_cache_alloc_node+0x166/0x450
kmalloc_node_trace+0x3a/0x70
iucv_cpu_prepare+0x44/0xd0
cpuhp_invoke_callback+0x156/0x2f0
cpuhp_issue_call+0xf0/0x298
__cpuhp_setup_state_cpuslocked+0x136/0x338
__cpuhp_setup_state+0xf4/0x288
iucv_init+0xf4/0x280
do_one_initcall+0x78/0x390
do_initcalls+0x11a/0x140
kernel_init_freeable+0x25e/0x2a0
kernel_init+0x2e/0x170
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
Freed in iucv_init+0x92/0x280 age=167839 cpu=2 pid=1
__kmem_cache_free+0x308/0x358
iucv_init+0x92/0x280
do_one_initcall+0x78/0x390
do_initcalls+0x11a/0x140
kernel_init_freeable+0x25e/0x2a0
kernel_init+0x2e/0x170
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
Slab 0x0000037200010000 objects=32 used=30 fp=0x0000000000400640 flags=0x1ffff00000010200(slab|head|node=0|zone=0|
Object 0x0000000000400540 @offset=1344 fp=0x0000000000000000
Redzone 0000000000400500: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400510: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400520: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400530: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 0000000000400540: 00 01 00 03 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object 0000000000400550: f3 86 81 f2 f4 82 f8 82 f0 f0 f0 f0 f0 f0 f0 f2 ................
Object 0000000000400560: 00 00 00 00 80 00 00 00 cc cc cc cc cc cc cc cc ................
Object 0000000000400570: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Redzone 0000000000400580: cc cc cc cc cc cc cc cc ........
Padding 00000000004005d4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Padding 00000000004005e4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Padding 00000000004005f4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZ
CPU: 6 PID: 121030 Comm: 116-pai-crypto. Not tainted 6.3.0-20230221.rc0.git4.99b8246b2d71.300.fc37.s390x+debug #1
Hardware name: IBM 3931 A01 704 (z/VM 7.3.0)
Call Trace:
[<000000032aa034ec>] dump_stack_lvl+0xac/0x100
[<0000000329f5a6cc>] check_bytes_and_report+0x104/0x140
[<0000000329f5aa78>] check_object+0x370/0x3c0
[<0000000329f5ede6>] free_debug_processing+0x15e/0x348
[<0000000329f5f06a>] free_to_partial_list+0x9a/0x2f0
[<0000000329f5f4a4>] __slab_free+0x1e4/0x3a8
[<0000000329f61768>] __kmem_cache_free+0x308/0x358
[<000000032a91465c>] iucv_cpu_dead+0x6c/0x88
[<0000000329c2fc66>] cpuhp_invoke_callback+0x156/0x2f0
[<000000032aa062da>] _cpu_down.constprop.0+0x22a/0x5e0
[<0000000329c3243e>] cpu_device_down+0x4e/0x78
[<000000032a61dee0>] device_offline+0xc8/0x118
[<000000032a61e048>] online_store+0x60/0xe0
[<000000032a08b6b0>] kernfs_fop_write_iter+0x150/0x1e8
[<0000000329fab65c>] vfs_write+0x174/0x360
[<0000000329fab9fc>] ksys_write+0x74/0x100
[<000000032aa03a5a>] __do_syscall+0x1da/0x208
[<000000032aa177b2>] system_call+0x82/0xb0
INFO: lockdep is turned off.
FIX dma-kmalloc-64: Restoring kmalloc Redzone 0x0000000000400564-0x0000000000400567=0xcc
FIX dma-kmalloc-64: Object at 0x0000000000400540 not freed
Fixes: 2356f4cb1911 ("[S390]: Rewrite of the IUCV base code, part 2")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20230315131435.4113889-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit f96a3d74554d ("ipv4: Fix incorrect route flushing when source
address is deleted") started to take the table ID field in the FIB info
structure into account when determining if two structures are identical
or not. This field is initialized using the 'fc_table' field in the
route configuration structure, which is not set when adding a route via
IOCTL.
The above can result in user space being able to install two identical
routes that only differ in the table ID field of their associated FIB
info.
Fix by initializing the table ID field in the route configuration
structure in the IOCTL path.
Before the fix:
# ip route add default via 192.0.2.2
# route add default gw 192.0.2.2
# ip -4 r show default
# default via 192.0.2.2 dev dummy10
# default via 192.0.2.2 dev dummy10
After the fix:
# ip route add default via 192.0.2.2
# route add default gw 192.0.2.2
SIOCADDRT: File exists
# ip -4 r show default
default via 192.0.2.2 dev dummy10
Audited the code paths to ensure there are no other paths that do not
properly initialize the route configuration structure when installing a
route.
Fixes: 5a56a0b3a45d ("net: Don't delete routes in different VRFs")
Fixes: f96a3d74554d ("ipv4: Fix incorrect route flushing when source address is deleted")
Reported-by: gaoxingwang <gaoxingwang1@huawei.com>
Link: https://lore.kernel.org/netdev/20230314144159.2354729-1-gaoxingwang1@huawei.com/
Tested-by: gaoxingwang <gaoxingwang1@huawei.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230315124009.4015212-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2023-03-15
1) Fix an information leak when dumping algos and encap.
From Herbert Xu
2) Allow transport-mode states with AF_UNSPEC selector
to allow for nested transport-mode states.
From Herbert Xu.
* tag 'ipsec-2023-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: Allow transport-mode states with AF_UNSPEC selector
xfrm: Zero padding when dumping algos and encap
====================
Link: https://lore.kernel.org/r/20230315105623.1396491-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when dsa_slave_change_mtu() is called on a user port where
dev->max_mtu is 1500 (as returned by ds->ops->port_max_mtu()), the code
will stumble upon this check:
if (new_master_mtu > mtu_limit)
return -ERANGE;
because new_master_mtu is adjusted for the tagger overhead but mtu_limit
is not.
But it would be good if the logic went through, for example if the DSA
master really depends on an MTU adjustment to accept DSA-tagged frames.
To make the code pass through the check, we need to adjust mtu_limit for
the overhead as well, if the minimum restriction was caused by the DSA
user port's MTU (dev->max_mtu). A DSA user port MTU and a DSA master MTU
are always offset by the protocol overhead.
Currently no drivers return 1500 .port_max_mtu(), but this is only
temporary and a bug in itself - mv88e6xxx should have done that, but
since commit b9c587fed61c ("dsa: mv88e6xxx: Include tagger overhead when
setting MTU for DSA and CPU ports") it no longer does. This is a
preparation for fixing that.
Fixes: bfcb813203e6 ("net: dsa: configure the MTU for switch ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This returns behaviour of SOCK_STREAM read as before skbuff usage. When
copying to user fails current skbuff won't be dropped, but returned to
sockets's queue. Technically instead of 'skb_dequeue()', 'skb_peek()' is
called and when skbuff becomes empty, it is removed from queue by
'__skb_unlink()'.
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now no longer use 'skb->len' to update credit, there is no sense
to update skbuff state, because it is used only once after dequeue to
copy data and then will be released.
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'skb->len' can vary when we partially read the data, this complicates the
calculation of credit to be updated in 'virtio_transport_inc_rx_pkt()/
virtio_transport_dec_rx_pkt()'.
Also in 'virtio_transport_dec_rx_pkt()' we were miscalculating the
credit since 'skb->len' was redundant.
For these reasons, let's replace the use of skbuff state to calculate new
'rx_bytes'/'fwd_cnt' values with explicit value as input argument. This
makes code more simple, because it is not needed to change skbuff state
before each call to update 'rx_bytes'/'fwd_cnt'.
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CLC message initialization was not properly reversed in error handling path.
Reported-and-suggested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following LOCKDEP was detected:
Workqueue: events smc_lgr_free_work [smc]
WARNING: possible circular locking dependency detected
6.1.0-20221027.rc2.git8.56bc5b569087.300.fc36.s390x+debug #1 Not tainted
------------------------------------------------------
kworker/3:0/176251 is trying to acquire lock:
00000000f1467148 ((wq_completion)smc_tx_wq-00000000#2){+.+.}-{0:0},
at: __flush_workqueue+0x7a/0x4f0
but task is already holding lock:
0000037fffe97dc8 ((work_completion)(&(&lgr->free_work)->work)){+.+.}-{0:0},
at: process_one_work+0x232/0x730
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #4 ((work_completion)(&(&lgr->free_work)->work)){+.+.}-{0:0}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
__flush_work+0x76/0xf0
__cancel_work_timer+0x170/0x220
__smc_lgr_terminate.part.0+0x34/0x1c0 [smc]
smc_connect_rdma+0x15e/0x418 [smc]
__smc_connect+0x234/0x480 [smc]
smc_connect+0x1d6/0x230 [smc]
__sys_connect+0x90/0xc0
__do_sys_socketcall+0x186/0x370
__do_syscall+0x1da/0x208
system_call+0x82/0xb0
-> #3 (smc_client_lgr_pending){+.+.}-{3:3}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
__mutex_lock+0x96/0x8e8
mutex_lock_nested+0x32/0x40
smc_connect_rdma+0xa4/0x418 [smc]
__smc_connect+0x234/0x480 [smc]
smc_connect+0x1d6/0x230 [smc]
__sys_connect+0x90/0xc0
__do_sys_socketcall+0x186/0x370
__do_syscall+0x1da/0x208
system_call+0x82/0xb0
-> #2 (sk_lock-AF_SMC){+.+.}-{0:0}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
lock_sock_nested+0x46/0xa8
smc_tx_work+0x34/0x50 [smc]
process_one_work+0x30c/0x730
worker_thread+0x62/0x420
kthread+0x138/0x150
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
-> #1 ((work_completion)(&(&smc->conn.tx_work)->work)){+.+.}-{0:0}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
process_one_work+0x2bc/0x730
worker_thread+0x62/0x420
kthread+0x138/0x150
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
-> #0 ((wq_completion)smc_tx_wq-00000000#2){+.+.}-{0:0}:
check_prev_add+0xd8/0xe88
validate_chain+0x70c/0xb20
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
__flush_workqueue+0xaa/0x4f0
drain_workqueue+0xaa/0x158
destroy_workqueue+0x44/0x2d8
smc_lgr_free+0x9e/0xf8 [smc]
process_one_work+0x30c/0x730
worker_thread+0x62/0x420
kthread+0x138/0x150
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
other info that might help us debug this:
Chain exists of:
(wq_completion)smc_tx_wq-00000000#2
--> smc_client_lgr_pending
--> (work_completion)(&(&lgr->free_work)->work)
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((work_completion)(&(&lgr->free_work)->work));
lock(smc_client_lgr_pending);
lock((work_completion)
(&(&lgr->free_work)->work));
lock((wq_completion)smc_tx_wq-00000000#2);
*** DEADLOCK ***
2 locks held by kworker/3:0/176251:
#0: 0000000080183548
((wq_completion)events){+.+.}-{0:0},
at: process_one_work+0x232/0x730
#1: 0000037fffe97dc8
((work_completion)
(&(&lgr->free_work)->work)){+.+.}-{0:0},
at: process_one_work+0x232/0x730
stack backtrace:
CPU: 3 PID: 176251 Comm: kworker/3:0 Not tainted
Hardware name: IBM 8561 T01 701 (z/VM 7.2.0)
Call Trace:
[<000000002983c3e4>] dump_stack_lvl+0xac/0x100
[<0000000028b477ae>] check_noncircular+0x13e/0x160
[<0000000028b48808>] check_prev_add+0xd8/0xe88
[<0000000028b49cc4>] validate_chain+0x70c/0xb20
[<0000000028b4bd26>] __lock_acquire+0x58e/0xbd8
[<0000000028b4cf6a>] lock_acquire.part.0+0xe2/0x248
[<0000000028b4d17c>] lock_acquire+0xac/0x1c8
[<0000000028addaaa>] __flush_workqueue+0xaa/0x4f0
[<0000000028addf9a>] drain_workqueue+0xaa/0x158
[<0000000028ae303c>] destroy_workqueue+0x44/0x2d8
[<000003ff8029af26>] smc_lgr_free+0x9e/0xf8 [smc]
[<0000000028adf3d4>] process_one_work+0x30c/0x730
[<0000000028adf85a>] worker_thread+0x62/0x420
[<0000000028aeac50>] kthread+0x138/0x150
[<0000000028a63914>] __ret_from_fork+0x3c/0x58
[<00000000298503da>] ret_from_fork+0xa/0x40
INFO: lockdep is turned off.
===================================================================
This deadlock occurs because cancel_delayed_work_sync() waits for
the work(&lgr->free_work) to finish, while the &lgr->free_work
waits for the work(lgr->tx_wq), which needs the sk_lock-AF_SMC, that
is already used under the mutex_lock.
The solution is to use cancel_delayed_work() instead, which kills
off a pending work.
Fixes: a52bcc919b14 ("net/smc: improve termination processing")
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paul Holzinger reported [0] that commit 5456262d2baa ("net: Fix
incorrect address comparison when searching for a bind2 bucket")
introduced a bind() regression. Paul also gave a nice repro that
calls two types of bind() on the same port, both of which now
succeed, but the second call should fail:
bind(fd1, ::, port) + bind(fd2, 127.0.0.1, port)
The cited commit added address family tests in three functions to
fix the uninit-value KMSAN report. [1] However, the test added to
inet_bind2_bucket_match_addr_any() removed a necessary conflict
check; the dual-stack wildcard address no longer conflicts with
an IPv4 non-wildcard address.
If tb->family is AF_INET6 and sk->sk_family is AF_INET in
inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the dual-stack wildcard address.
Note that the IPv4 wildcard address does not conflict with
IPv6 non-wildcard addresses.
[0]: https://lore.kernel.org/netdev/e21bf153-80b0-9ec0-15ba-e04a4ad42c34@redhat.com/
[1]: https://lore.kernel.org/netdev/CAG_fn=Ud3zSW7AZWXc+asfMhZVL5ETnvuY44Pmyv4NPv-ijN-A@mail.gmail.com/
Fixes: 5456262d2baa ("net: Fix incorrect address comparison when searching for a bind2 bucket")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reported-by: Paul Holzinger <pholzing@redhat.com>
Link: https://lore.kernel.org/netdev/CAG_fn=Ud3zSW7AZWXc+asfMhZVL5ETnvuY44Pmyv4NPv-ijN-A@mail.gmail.com/
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paul Holzinger <pholzing@redhat.com>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IP tunnels can apparently update dev->needed_headroom
in their xmit path.
This patch takes care of three tunnels xmit, and also the
core LL_RESERVED_SPACE() and LL_RESERVED_SPACE_EXTRA()
helpers.
More changes might be needed for completeness.
BUG: KCSAN: data-race in ip_tunnel_xmit / ip_tunnel_xmit
read to 0xffff88815b9da0ec of 2 bytes by task 888 on cpu 1:
ip_tunnel_xmit+0x1270/0x1730 net/ipv4/ip_tunnel.c:803
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
dev_queue_xmit include/linux/netdevice.h:3051 [inline]
neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623
neigh_output include/net/neighbour.h:546 [inline]
ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228
ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:444 [inline]
ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126
iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
dev_queue_xmit include/linux/netdevice.h:3051 [inline]
neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623
neigh_output include/net/neighbour.h:546 [inline]
ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228
ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:444 [inline]
ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126
iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
dev_queue_xmit include/linux/netdevice.h:3051 [inline]
neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623
neigh_output include/net/neighbour.h:546 [inline]
ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228
ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:444 [inline]
ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126
iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
dev_queue_xmit include/linux/netdevice.h:3051 [inline]
neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623
neigh_output include/net/neighbour.h:546 [inline]
ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228
ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:444 [inline]
ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126
iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
dev_queue_xmit include/linux/netdevice.h:3051 [inline]
neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623
neigh_output include/net/neighbour.h:546 [inline]
ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228
ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:444 [inline]
ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126
iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
dev_queue_xmit include/linux/netdevice.h:3051 [inline]
neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623
neigh_output include/net/neighbour.h:546 [inline]
ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228
ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:444 [inline]
ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126
iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
write to 0xffff88815b9da0ec of 2 bytes by task 2379 on cpu 0:
ip_tunnel_xmit+0x1294/0x1730 net/ipv4/ip_tunnel.c:804
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661
__netdev_start_xmit include/linux/netdevice.h:4881 [inline]
netdev_start_xmit include/linux/netdevice.h:4895 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596
__dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246
dev_queue_xmit include/linux/netdevice.h:3051 [inline]
neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623
neigh_output include/net/neighbour.h:546 [inline]
ip6_finish_output2+0x9bc/0xc50 net/ipv6/ip6_output.c:134
__ip6_finish_output net/ipv6/ip6_output.c:195 [inline]
ip6_finish_output+0x39a/0x4e0 net/ipv6/ip6_output.c:206
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip6_output+0xeb/0x220 net/ipv6/ip6_output.c:227
dst_output include/net/dst.h:444 [inline]
NF_HOOK include/linux/netfilter.h:302 [inline]
mld_sendpack+0x438/0x6a0 net/ipv6/mcast.c:1820
mld_send_cr net/ipv6/mcast.c:2121 [inline]
mld_ifc_work+0x519/0x7b0 net/ipv6/mcast.c:2653
process_one_work+0x3e6/0x750 kernel/workqueue.c:2390
worker_thread+0x5f2/0xa10 kernel/workqueue.c:2537
kthread+0x1ac/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
value changed: 0x0dd4 -> 0x0e14
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 2379 Comm: kworker/0:0 Not tainted 6.3.0-rc1-syzkaller-00002-g8ca09d5fa354-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023
Workqueue: mld mld_ifc_work
Fixes: 8eb30be0352d ("ipv6: Create ip6_tnl_xmit")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230310191109.2384387-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the
node will be deleted from the node_db list. If a frame is sent to the node
after it is deleted, a netdev_err message for each slave interface is
produced. This should not happen with dan nodes because of supervision
frames, but can happen often with san nodes, which clutters the kernel
log. Since the hsr protocol does not support sans, this is only relevant
for the prp protocol.
Signed-off-by: Kristian Overskeid <koverskeid@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When performing a stress test on SMC-R by rmmod mlx5_ib driver
during the wrk/nginx test, we found that there is a probability
of triggering a panic while terminating all link groups.
This issue dues to the race between smc_smcr_terminate_all()
and smc_buf_create().
smc_smcr_terminate_all
smc_buf_create
/* init */
conn->sndbuf_desc = NULL;
...
__smc_lgr_terminate
smc_conn_kill
smc_close_abort
smc_cdc_get_slot_and_msg_send
__softirqentry_text_start
smc_wr_tx_process_cqe
smc_cdc_tx_handler
READ(conn->sndbuf_desc->len);
/* panic dues to NULL sndbuf_desc */
conn->sndbuf_desc = xxx;
This patch tries to fix the issue by always to check the sndbuf_desc
before send any cdc msg, to make sure that no null pointer is
seen during cqe processing.
Fixes: 0b29ec643613 ("net/smc: immediate termination for SMCR link groups")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://lore.kernel.org/r/1678263432-17329-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts part of commit 015b8cc5e7c4 ("wifi: cfg80211: Fix use after
free for wext")
This commit broke WPA offload by unconditionally clearing the crypto
modes for non-WEP connections. Drop that part of the patch.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reported-by: Ilya <me@0upti.me>
Reported-and-tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Fixes: 015b8cc5e7c4 ("wifi: cfg80211: Fix use after free for wext")
Cc: stable@kernel.org
Link: https://lore.kernel.org/linux-wireless/ZAx0TWRBlGfv7pNl@kroah.com/T/#m11e6e0915ab8fa19ce8bc9695ab288c0fe018edf
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) nft_parse_register_load() gets an incorrect datatype size
as input, from Jeremy Sowden.
2) incorrect maximum netlink attribute in nft_redir, also
from Jeremy.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_redir: correct value of inet type `.maxattrs`
netfilter: nft_redir: correct length for loading protocol registers
netfilter: nft_masq: correct length for loading protocol registers
netfilter: nft_nat: correct length for loading protocol registers
====================
Link: https://lore.kernel.org/r/20230309174655.69816-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Christoph reports a lockdep splat in the mptcp_subflow_create_socket()
error path, when such function is invoked by
mptcp_pm_nl_create_listen_socket().
Such code path acquires two separates, nested socket lock, with the
internal lock operation lacking the "nested" annotation. Adding that
in sock_release() for mptcp's sake only could be confusing.
Instead just add a new lockclass to the in-kernel msk socket,
re-initializing the lockdep infra after the socket creation.
Fixes: ad2171009d96 ("mptcp: fix locking for in-kernel listener creation")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/354
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_set_state() is called from tcp_done() already.
There is then no need to first set the state to TCP_CLOSE, then call
tcp_done().
Fixes: d582484726c4 ("mptcp: fix fallback for MP_JOIN subflows")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/362
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add __ro_after_init labels for the variables tcp_prot_override and
tcpv6_prot_override, just like other variables adjacent to them, to
indicate that they are initialised from the init hooks and no writes
occur afterwards.
Fixes: b19bc2945b40 ("mptcp: implement delegated actions")
Cc: stable@vger.kernel.org
Fixes: 51fa7f8ebf0e ("mptcp: mark ops structures as ro_after_init")
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As reported by Christoph after having refactored the passive
socket initialization, the mptcp listener shutdown path is prone
to an UaF issue.
BUG: KASAN: use-after-free in _raw_spin_lock_bh+0x73/0xe0
Write of size 4 at addr ffff88810cb23098 by task syz-executor731/1266
CPU: 1 PID: 1266 Comm: syz-executor731 Not tainted 6.2.0-rc59af4eaa31c1f6c00c8f1e448ed99a45c66340dd5 #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0x91
print_report+0x16a/0x46f
kasan_report+0xad/0x130
kasan_check_range+0x14a/0x1a0
_raw_spin_lock_bh+0x73/0xe0
subflow_error_report+0x6d/0x110
sk_error_report+0x3b/0x190
tcp_disconnect+0x138c/0x1aa0
inet_child_forget+0x6f/0x2e0
inet_csk_listen_stop+0x209/0x1060
__mptcp_close_ssk+0x52d/0x610
mptcp_destroy_common+0x165/0x640
mptcp_destroy+0x13/0x80
__mptcp_destroy_sock+0xe7/0x270
__mptcp_close+0x70e/0x9b0
mptcp_close+0x2b/0x150
inet_release+0xe9/0x1f0
__sock_release+0xd2/0x280
sock_close+0x15/0x20
__fput+0x252/0xa20
task_work_run+0x169/0x250
exit_to_user_mode_prepare+0x113/0x120
syscall_exit_to_user_mode+0x1d/0x40
do_syscall_64+0x48/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
The msk grace period can legitly expire in between the last
reference count dropped in mptcp_subflow_queue_clean() and
the later eventual access in inet_csk_listen_stop()
After the previous patch we don't need anymore special-casing
msk listener socket cleanup: the mptcp worker will process each
of the unaccepted msk sockets.
Just drop the now unnecessary code.
Please note this commit depends on the two parent ones:
mptcp: refactor passive socket initialization
mptcp: use the workqueue to destroy unaccepted sockets
Fixes: 6aeed9045071 ("mptcp: fix race on unaccepted mptcp sockets")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/346
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Christoph reported a UaF at token lookup time after having
refactored the passive socket initialization part:
BUG: KASAN: use-after-free in __token_bucket_busy+0x253/0x260
Read of size 4 at addr ffff88810698d5b0 by task syz-executor653/3198
CPU: 1 PID: 3198 Comm: syz-executor653 Not tainted 6.2.0-rc59af4eaa31c1f6c00c8f1e448ed99a45c66340dd5 #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0x91
print_report+0x16a/0x46f
kasan_report+0xad/0x130
__token_bucket_busy+0x253/0x260
mptcp_token_new_connect+0x13d/0x490
mptcp_connect+0x4ed/0x860
__inet_stream_connect+0x80e/0xd90
tcp_sendmsg_fastopen+0x3ce/0x710
mptcp_sendmsg+0xff1/0x1a20
inet_sendmsg+0x11d/0x140
__sys_sendto+0x405/0x490
__x64_sys_sendto+0xdc/0x1b0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
We need to properly clean-up all the paired MPTCP-level
resources and be sure to release the msk last, even when
the unaccepted subflow is destroyed by the TCP internals
via inet_child_forget().
We can re-use the existing MPTCP_WORK_CLOSE_SUBFLOW infra,
explicitly checking that for the critical scenario: the
closed subflow is the MPC one, the msk is not accepted and
eventually going through full cleanup.
With such change, __mptcp_destroy_sock() is always called
on msk sockets, even on accepted ones. We don't need anymore
to transiently drop one sk reference at msk clone time.
Please note this commit depends on the parent one:
mptcp: refactor passive socket initialization
Fixes: 58b09919626b ("mptcp: create msk early")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/347
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 30e51b923e43 ("mptcp: fix unreleased socket in accept queue")
unaccepted msk sockets go throu complete shutdown, we don't need anymore
to delay inserting the first subflow into the subflow lists.
The reference counting deserve some extra care, as __mptcp_close() is
unaware of the request socket linkage to the first subflow.
Please note that this is more a refactoring than a fix but because this
modification is needed to include other corrections, see the following
commits. Then a Fixes tag has been added here to help the stable team.
Fixes: 30e51b923e43 ("mptcp: fix unreleased socket in accept queue")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Christoph reported a possible deadlock while the TCP stack
destroys an unaccepted subflow due to an incoming reset: the
MPTCP socket error path tries to acquire the msk-level socket
lock while TCP still owns the listener socket accept queue
spinlock, and the reverse dependency already exists in the
TCP stack.
Note that the above is actually a lockdep false positive, as
the chain involves two separate sockets. A different per-socket
lockdep key will address the issue, but such a change will be
quite invasive.
Instead, we can simply stop earlier the socket error handling
for orphaned or unaccepted subflows, breaking the critical
lockdep chain. Error handling in such a scenario is a no-op.
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 15cc10453398 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/355
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce xdp_set_features_flag utility routine in order to update
dynamically xdp_features according to the dynamic hw configuration via
ethtool (e.g. changing number of hw rx/tx queues).
Add xdp_clear_features_flag() in order to clear all xdp_feature flag.
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Just a few fixes:
* MLO connection socket ownership didn't work
* basic rates validation was missing (reported by
by a private syzbot instances)
* puncturing bitmap netlink policy was completely broken
* properly check chandef for NULL channel, it can be
pointing to a chandef that's still uninitialized
* tag 'wireless-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cfg80211: fix MLO connection ownership
wifi: mac80211: check basic rates validity
wifi: nl80211: fix puncturing bitmap policy
wifi: nl80211: fix NULL-ptr deref in offchan check
====================
Link: https://lore.kernel.org/r/20230310114647.35422-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Protect NFSD writes against filesystem freezing
- Fix a potential memory leak during server shutdown
* tag 'nfsd-6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
SUNRPC: Fix a server shutdown leak
NFSD: Protect against filesystem freezing
|
|
When disconnecting from an MLO connection we need the AP
MLD address, not an arbitrary BSSID. Fix the code to do
that.
Fixes: 9ecff10e82a5 ("wifi: nl80211: refactor BSS lookup in nl80211_associate()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.4c1b3b18980e.I008f070c7f3b8e8bde9278101ef9e40706a82902@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When userspace sets basic rates, it might send us some rates
list that's empty or consists of invalid values only. We're
currently ignoring invalid values and then may end up with a
rates bitmap that's empty, which later results in a warning.
Reject the call if there were no valid rates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This was meant to be a u32, and while applying the patch
I tried to use policy validation for it. However, not only
did I copy/paste it to u8 instead of u32, but also used
the policy range erroneously. Fix both of these issues.
Fixes: d7c1a9a0ed18 ("wifi: nl80211: validate and configure puncturing bitmap")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If, e.g. in AP mode, the link was already created by userspace
but not activated yet, it has a chandef but the chandef isn't
valid and has no channel. Check for this and ignore this link.
Fixes: 7b0a0e3c3a88 ("wifi: cfg80211: do some rework towards MLO link APIs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.71bd4803fbb9.Iee39c0f6c2d3a59a8227674dc55d52e38b1090cf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
tcp_rtx_synack() now could be called in process context as explained in
0a375c822497 ("tcp: tcp_rtx_synack() can be called from process
context").
tcp_rtx_synack() might call tcp_make_synack(), which will touch per-CPU
variables with preemption enabled. This causes the following BUG:
BUG: using __this_cpu_add() in preemptible [00000000] code: ThriftIO1/5464
caller is tcp_make_synack+0x841/0xac0
Call Trace:
<TASK>
dump_stack_lvl+0x10d/0x1a0
check_preemption_disabled+0x104/0x110
tcp_make_synack+0x841/0xac0
tcp_v6_send_synack+0x5c/0x450
tcp_rtx_synack+0xeb/0x1f0
inet_rtx_syn_ack+0x34/0x60
tcp_check_req+0x3af/0x9e0
tcp_rcv_state_process+0x59b/0x2030
tcp_v6_do_rcv+0x5f5/0x700
release_sock+0x3a/0xf0
tcp_sendmsg+0x33/0x40
____sys_sendmsg+0x2f2/0x490
__sys_sendmsg+0x184/0x230
do_syscall_64+0x3d/0x90
Avoid calling __TCP_INC_STATS() with will touch per-cpu variables. Use
TCP_INC_STATS() which is safe to be called from context switch.
Fixes: 8336886f786f ("tcp: TCP Fast Open Server - support TFO listeners")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230308190745.780221-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter and bpf.
Current release - regressions:
- core: avoid skb end_offset change in __skb_unclone_keeptruesize()
- sched:
- act_connmark: handle errno on tcf_idr_check_alloc
- flower: fix fl_change() error recovery path
- ieee802154: prevent user from crashing the host
Current release - new code bugs:
- eth: bnxt_en: fix the double free during device removal
- tools: ynl:
- fix enum-as-flags in the generic CLI
- fully inherit attrs in subsets
- re-license uniformly under GPL-2.0 or BSD-3-clause
Previous releases - regressions:
- core: use indirect calls helpers for sk_exit_memory_pressure()
- tls:
- fix return value for async crypto
- avoid hanging tasks on the tx_lock
- eth: ice: copy last block omitted in ice_get_module_eeprom()
Previous releases - always broken:
- core: avoid double iput when sock_alloc_file fails
- af_unix: fix struct pid leaks in OOB support
- tls:
- fix possible race condition
- fix device-offloaded sendpage straddling records
- bpf:
- sockmap: fix an infinite loop error
- test_run: fix &xdp_frame misplacement for LIVE_FRAMES
- fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
- netfilter: tproxy: fix deadlock due to missing BH disable
- phylib: get rid of unnecessary locking
- eth: bgmac: fix *initial* chip reset to support BCM5358
- eth: nfp: fix csum for ipsec offload
- eth: mtk_eth_soc: fix RX data corruption issue
Misc:
- usb: qmi_wwan: add telit 0x1080 composition"
* tag 'net-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (64 commits)
tools: ynl: fix enum-as-flags in the generic CLI
tools: ynl: move the enum classes to shared code
net: avoid double iput when sock_alloc_file fails
af_unix: fix struct pid leaks in OOB support
eth: fealnx: bring back this old driver
net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
net: microchip: sparx5: fix deletion of existing DSCP mappings
octeontx2-af: Unlock contexts in the queue context cache in case of fault detection
net/smc: fix fallback failed while sendmsg with fastopen
ynl: re-license uniformly under GPL-2.0 OR BSD-3-Clause
mailmap: update entries for Stephen Hemminger
mailmap: add entry for Maxim Mikityanskiy
nfc: change order inside nfc_se_io error path
ethernet: ice: avoid gcc-9 integer overflow warning
ice: don't ignore return codes in VSI related code
ice: Fix DSCP PFC TLV creation
net: usb: qmi_wwan: add Telit 0x1080 composition
net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990
netfilter: conntrack: adopt safer max chain length
net: tls: fix device-offloaded sendpage straddling records
...
|
|
When sock_alloc_file fails to allocate a file, it will call sock_release.
__sys_socket_file should then not call sock_release again, otherwise there
will be a double free.
[ 89.319884] ------------[ cut here ]------------
[ 89.320286] kernel BUG at fs/inode.c:1764!
[ 89.320656] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 89.321051] CPU: 7 PID: 125 Comm: iou-sqp-124 Not tainted 6.2.0+ #361
[ 89.321535] RIP: 0010:iput+0x1ff/0x240
[ 89.321808] Code: d1 83 e1 03 48 83 f9 02 75 09 48 81 fa 00 10 00 00 77 05 83 e2 01 75 1f 4c 89 ef e8 fb d2 ba 00 e9 80 fe ff ff c3 cc cc cc cc <0f> 0b 0f 0b e9 d0 fe ff ff 0f 0b eb 8d 49 8d b4 24 08 01 00 00 48
[ 89.322760] RSP: 0018:ffffbdd60068bd50 EFLAGS: 00010202
[ 89.323036] RAX: 0000000000000000 RBX: ffff9d7ad3cacac0 RCX: 0000000000001107
[ 89.323412] RDX: 000000000003af00 RSI: 0000000000000000 RDI: ffff9d7ad3cacb40
[ 89.323785] RBP: ffffbdd60068bd68 R08: ffffffffffffffff R09: ffffffffab606438
[ 89.324157] R10: ffffffffacb3dfa0 R11: 6465686361657256 R12: ffff9d7ad3cacb40
[ 89.324529] R13: 0000000080000001 R14: 0000000080000001 R15: 0000000000000002
[ 89.324904] FS: 00007f7b28516740(0000) GS:ffff9d7aeb1c0000(0000) knlGS:0000000000000000
[ 89.325328] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 89.325629] CR2: 00007f0af52e96c0 CR3: 0000000002a02006 CR4: 0000000000770ee0
[ 89.326004] PKRU: 55555554
[ 89.326161] Call Trace:
[ 89.326298] <TASK>
[ 89.326419] __sock_release+0xb5/0xc0
[ 89.326632] __sys_socket_file+0xb2/0xd0
[ 89.326844] io_socket+0x88/0x100
[ 89.327039] ? io_issue_sqe+0x6a/0x430
[ 89.327258] io_issue_sqe+0x67/0x430
[ 89.327450] io_submit_sqes+0x1fe/0x670
[ 89.327661] io_sq_thread+0x2e6/0x530
[ 89.327859] ? __pfx_autoremove_wake_function+0x10/0x10
[ 89.328145] ? __pfx_io_sq_thread+0x10/0x10
[ 89.328367] ret_from_fork+0x29/0x50
[ 89.328576] RIP: 0033:0x0
[ 89.328732] Code: Unable to access opcode bytes at 0xffffffffffffffd6.
[ 89.329073] RSP: 002b:0000000000000000 EFLAGS: 00000202 ORIG_RAX: 00000000000001a9
[ 89.329477] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00007f7b28637a3d
[ 89.329845] RDX: 00007fff4e4318a8 RSI: 00007fff4e4318b0 RDI: 0000000000000400
[ 89.330216] RBP: 00007fff4e431830 R08: 00007fff4e431711 R09: 00007fff4e4318b0
[ 89.330584] R10: 0000000000000000 R11: 0000000000000202 R12: 00007fff4e441b38
[ 89.330950] R13: 0000563835e3e725 R14: 0000563835e40d10 R15: 00007f7b28784040
[ 89.331318] </TASK>
[ 89.331441] Modules linked in:
[ 89.331617] ---[ end trace 0000000000000000 ]---
Fixes: da214a475f8b ("net: add __sys_socket_file()")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230307173707.468744-1-cascardo@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported struct pid leak [1].
Issue is that queue_oob() calls maybe_add_creds() which potentially
holds a reference on a pid.
But skb->destructor is not set (either directly or by calling
unix_scm_to_skb())
This means that subsequent kfree_skb() or consume_skb() would leak
this reference.
In this fix, I chose to fully support scm even for the OOB message.
[1]
BUG: memory leak
unreferenced object 0xffff8881053e7f80 (size 128):
comm "syz-executor242", pid 5066, jiffies 4294946079 (age 13.220s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff812ae26a>] alloc_pid+0x6a/0x560 kernel/pid.c:180
[<ffffffff812718df>] copy_process+0x169f/0x26c0 kernel/fork.c:2285
[<ffffffff81272b37>] kernel_clone+0xf7/0x610 kernel/fork.c:2684
[<ffffffff812730cc>] __do_sys_clone+0x7c/0xb0 kernel/fork.c:2825
[<ffffffff849ad699>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff849ad699>] do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
[<ffffffff84a0008b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 314001f0bf92 ("af_unix: Add OOB support")
Reported-by: syzbot+7699d9e5635c10253a27@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rao Shoaib <rao.shoaib@oracle.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230307164530.771896-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a race where kthread_stop() may prevent the threadfn from ever getting
called. If that happens the svc_rqst will not be cleaned up.
Fixes: ed6473ddc704 ("NFSv4: Fix callback server shutdown")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
Before determining whether the msg has unsupported options, it has been
prematurely terminated by the wrong status check.
For the application, the general usages of MSG_FASTOPEN likes
fd = socket(...)
/* rather than connect */
sendto(fd, data, len, MSG_FASTOPEN)
Hence, We need to check the flag before state check, because the sock
state here is always SMC_INIT when applications tries MSG_FASTOPEN.
Once we found unsupported options, fallback it to TCP.
Fixes: ee9dfbef02d1 ("net/smc: handle sockopts forcing fallback")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
v2 -> v1: Optimize code style
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
`nft_redir_inet_type.maxattrs` was being set, presumably because of a
cut-and-paste error, to `NFTA_MASQ_MAX`, instead of `NFTA_REDIR_MAX`.
Fixes: 63ce3940f3ab ("netfilter: nft_redir: add inet support")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The values in the protocol registers are two bytes wide. However, when
parsing the register loads, the code currently uses the larger 16-byte
size of a `union nf_inet_addr`. Change it to use the (correct) size of
a `union nf_conntrack_man_proto` instead.
Fixes: d07db9884a5f ("netfilter: nf_tables: introduce nft_validate_register_load()")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|