summaryrefslogtreecommitdiff
path: root/net/mac80211
AgeCommit message (Collapse)AuthorFilesLines
2017-06-13mac80211: don't look at the PM bit of BAR framesEmmanuel Grumbach1-1/+5
When a peer sends a BAR frame with PM bit clear, we should not modify its PM state as madated by the spec in 802.11-20012 10.2.1.2. Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-07net: Fix inconsistent teardown and release of private netdev state.David S. Miller1-3/+3
Network devices can allocate reasources and private memory using netdev_ops->ndo_init(). However, the release of these resources can occur in one of two different places. Either netdev_ops->ndo_uninit() or netdev->destructor(). The decision of which operation frees the resources depends upon whether it is necessary for all netdev refs to be released before it is safe to perform the freeing. netdev_ops->ndo_uninit() presumably can occur right after the NETDEV_UNREGISTER notifier completes and the unicast and multicast address lists are flushed. netdev->destructor(), on the other hand, does not run until the netdev references all go away. Further complicating the situation is that netdev->destructor() almost universally does also a free_netdev(). This creates a problem for the logic in register_netdevice(). Because all callers of register_netdevice() manage the freeing of the netdev, and invoke free_netdev(dev) if register_netdevice() fails. If netdev_ops->ndo_init() succeeds, but something else fails inside of register_netdevice(), it does call ndo_ops->ndo_uninit(). But it is not able to invoke netdev->destructor(). This is because netdev->destructor() will do a free_netdev() and then the caller of register_netdevice() will do the same. However, this means that the resources that would normally be released by netdev->destructor() will not be. Over the years drivers have added local hacks to deal with this, by invoking their destructor parts by hand when register_netdevice() fails. Many drivers do not try to deal with this, and instead we have leaks. Let's close this hole by formalizing the distinction between what private things need to be freed up by netdev->destructor() and whether the driver needs unregister_netdevice() to perform the free_netdev(). netdev->priv_destructor() performs all actions to free up the private resources that used to be freed by netdev->destructor(), except for free_netdev(). netdev->needs_free_netdev is a boolean that indicates whether free_netdev() should be done at the end of unregister_netdevice(). Now, register_netdevice() can sanely release all resources after ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit() and netdev->priv_destructor(). And at the end of unregister_netdevice(), we invoke netdev->priv_destructor() and optionally call free_netdev(). Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01mac80211: fix dropped counter in multiqueue RXJohannes Berg1-1/+1
In the commit enabling per-CPU station statistics, I inadvertedly copy-pasted some code to update rx_packets and forgot to change it to update rx_dropped_misc. Fix that. This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953. Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU") Reported-by: Petru-Florin Mihancea <petrum@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-30mac80211: fix TX aggregation start/stop callback raceJohannes Berg5-100/+71
When starting or stopping an aggregation session, one of the steps is that the driver calls back to mac80211 that the start/stop can proceed. This is handled by queueing up a fake SKB and processing it from the normal iface/sdata work. Since this isn't flushed when disassociating, the following race is possible: * associate * start aggregation session * driver callback * disassociate * associate again to the same AP * callback processing runs, leading to a WARN_ON() that the TID hadn't requested aggregation If the second association isn't to the same AP, there would only be a message printed ("Could not find station: <addr>"), but the same race could happen. Fix this by not going the whole detour with a fake SKB etc. but simply looking up the aggregation session in the driver callback, marking it with a START_CB/STOP_CB bit and then scheduling the regular aggregation work that will now process these bits as well. This also simplifies the code and gets rid of the whole problem with allocation failures of said skb, which could have left the session in limbo. Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-17mac80211: strictly check mesh address extension modeRajkumar Manoharan1-1/+2
Mesh forwarding path checks for address extension mode to fetch appropriate proxied address and MPP address. Existing condition that looks for 6 address format is not strict enough so that frames with improper values are processed and invalid entries are added into MPP table. Fix that by adding a stricter check before processing the packet. Per IEEE Std 802.11s-2011 spec. Table 7-6g1 lists address extension mode 0x3 as reserved one. And also Table Table 9-13 does not specify 0x3 as valid address field. Fixes: 9b395bc3be1c ("mac80211: verify that skb data is present") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-08mac80211: fix IBSS presp allocation sizeJohannes Berg1-0/+2
When VHT IBSS support was added, the size of the extra elements wasn't considered in ieee80211_ibss_build_presp(), which makes it possible that it would overrun the allocated buffer. Fix it by allocating the necessary space. Fixes: abcff6ef01f9 ("mac80211: add VHT support for IBSS") Reported-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-08mac80211: bail out from prep_connection() if a reconfig is ongoingLuca Coelho1-0/+4
If ieee80211_hw_restart() is called during authentication, the authentication process will continue, causing the driver to be called in a wrong state. This ultimately causes an oops in the iwlwifi driver (at least). This fixes bugzilla 195299 partly. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195299 Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28cfg80211: add request id to cfg80211_sched_scan_*() apiArend Van Spriel3-4/+4
Have proper request id filled in the SCHED_SCAN_RESULTS and SCHED_SCAN_STOPPED notifications toward user-space by having the driver provide it through the api. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: Add support for BSS max idle period elementAvraham Stern3-1/+23
Parse the BSS max idle period element and set the BSS configuration accordingly so the driver can use this information to configure the max idle period and to use protected management frames for keep alive when required. The BSS max idle period element is defined in IEEE802.11-2016, section 9.4.2.79 Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: Fix possible sband related NULL pointer de-referenceMohammed Shafi Shajakhan11-70/+139
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even if the channel context configuration is NULL. This crashes for chipsets which support 5 Ghz alone when it tries to access members of 'sband'. Channel context configuration can be NULL in multivif case and when channel switch is in progress (or) when it fails. Fix this by replacing the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which returns a NULL pointer for sband when the channel configuration is NULL. An example scenario is as below: In multivif mode (AP + STA) with drivers like ath10k, when we do a channel switch in the AP vif (which has a number of clients connected) and a STA vif which is connected to some other AP, when the channel switch in AP vif fails, while the STA vifs tries to connect to the other AP, there is a window where the channel context is NULL/invalid and this results in a crash while the clients connected to the AP vif tries to reconnect and this race is very similar to the one investigated by Michal in https://patchwork.kernel.org/patch/3788161/ and this does happens with hardware that supports 5Ghz alone after long hours of testing with continuous channel switch on the AP vif ieee80211 phy0: channel context reservation cannot be finalized because some interfaces aren't switching wlan0: failed to finalize CSA, disconnecting wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice (Reason: 3=DEAUTH_LEAVING) WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211] [<bf77272c>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211])) [<bf73cc50>] (nl80211_new_station [cfg80211]) Unable to handle kernel NULL pointer dereference at virtual address 00000014 pgd = d5f4c000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM PC is at sta_info_alloc+0x380/0x3fc [mac80211] LR is at sta_info_alloc+0x37c/0x3fc [mac80211] [<bf772738>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211]) [<bf73cc50>] (nl80211_new_station [cfg80211])) Cc: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: add ieee80211_tx_status_extFelix Fietkau1-28/+46
This allows the driver to pass in struct ieee80211_tx_status directly. Make ieee80211_tx_status_noskb a wrapper around it. As with ieee80211_tx_status_noskb, there is no _ni variant of this call, because it probably won't be needed. Even if the driver won't provide any extra status info other than what's in struct ieee80211_tx_info already, it can optimize status reporting this way by passing in the station pointer. Signed-off-by: Felix Fietkau <nbd@nbd.name> [use C99 initializers] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: move ieee80211_tx_status_noskb below ieee80211_tx_statusFelix Fietkau1-58/+58
Makes further cleanups more readable Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: make rate control tx status API more extensibleFelix Fietkau5-51/+42
Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack struct ieee80211_tx_status instead of struct ieee80211_tx_info. This struct can be used to pass extra information, e.g. for dynamic tx power control Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: use bitfield macros for encoded rateJohannes Berg2-30/+50
Instead of hand-coding the bit manipulations, use the bitfield macros to generate the code for the encoded bitrate. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: rename ieee80211_rx_status::vht_nss to just nssJohannes Berg3-7/+7
This field will need to be used again for HE, so rename it now. Again, mostly done with this spatch: @@ expression status; @@ -status->vht_nss +status->nss @@ expression status; @@ -status.vht_nss +status.nss Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: separate encoding/bandwidth from flagsJohannes Berg6-68/+75
We currently use a lot of flags that are mutually incompatible, separate this out into actual encoding and bandwidth enum values. Much of this again done with spatch, with manual post-editing, mostly to add the switch statements and get rid of the conversions. @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_80MHZ +status->bw = RATE_INFO_BW_80 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_40MHZ +status->bw = RATE_INFO_BW_40 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_20MHZ +status->bw = RATE_INFO_BW_20 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_160MHZ +status->bw = RATE_INFO_BW_160 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_5MHZ +status->bw = RATE_INFO_BW_5 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_10MHZ +status->bw = RATE_INFO_BW_10 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_VHT +status->encoding = RX_ENC_VHT @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_HT +status->encoding = RX_ENC_HT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_VHT +status.encoding = RX_ENC_VHT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_HT +status.encoding = RX_ENC_HT @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_HT) +(status->encoding == RX_ENC_HT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_VHT) +(status->encoding == RX_ENC_VHT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_5MHZ) +(status->bw == RATE_INFO_BW_5) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_10MHZ) +(status->bw == RATE_INFO_BW_10) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_40MHZ) +(status->bw == RATE_INFO_BW_40) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_80MHZ) +(status->bw == RATE_INFO_BW_80) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_160MHZ) +(status->bw == RATE_INFO_BW_160) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: clean up rate encoding bits in RX statusJohannes Berg6-55/+55
In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-26mac80211: make multicast variable a bool in ieee80211_accept_frame()Luca Coelho1-1/+1
The multicast variable in the ieee80211_accept_frame() function is treated as a boolean, but defined as int. Fix that. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-26mac80211: disentangle iflist_mtx and chanctx_mtxJohannes Berg3-8/+9
At least on iwlwifi, sometimes lockdep complains that we can lock chanctx_mtx -> mvm.mutex -> iflist_mtx (due to iterate_interfaces) and iflist_mtx -> chanctx_mtx Remove the latter dependency in mac80211 by using the RTNL that we already hold in one case, and can relatively easily achieve in the other case. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-26mac80211: don't parse encrypted management frames in ieee80211_frame_ackedEmmanuel Grumbach1-0/+1
ieee80211_frame_acked is called when a frame is acked by the peer. In case this is a management frame, we check if this an SMPS frame, in which case we can update our antenna configuration. When we parse the management frame we look at the category in case it is an action frame. That byte sits after the IV in case the frame was encrypted. This means that if the frame was encrypted, we basically look at the IV instead of looking at the category. It is then theorically possible that we think that an SMPS action frame was acked where really we had another frame that was encrypted. Since the only management frame whose ack needs to be tracked is the SMPS action frame, and that frame is not a robust management frame, it will never be encrypted. The easiest way to fix this problem is then to not look at frames that were encrypted. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-26cfg80211: add request id parameter to .sched_scan_stop() signatureArend Van Spriel1-1/+2
For multiple scheduled scan support the driver needs to know which scheduled scan request is being stopped. Pass the request id in the .sched_scan_stop() callback. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-25mac80211: rewrite monitor mode delivery logicJohannes Berg1-59/+92
The monitor mode delivery logic makes it hard to add any kind of filtering in an efficient way, because the monitor SKB is created first and then passed to all interfaces. Rewrite the logic to create the monitor SKB the first time it's actually needed, and then keep delivering it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-18/+68
Both conflict were simple overlapping changes. In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the conversion of the driver in net-next to use in-netdev stats. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-20mac80211: reject ToDS broadcast data framesJohannes Berg1-0/+21
AP/AP_VLAN modes don't accept any real 802.11 multicast data frames, but since they do need to accept broadcast management frames the same is currently permitted for data frames. This opens a security problem because such frames would be decrypted with the GTK, and could even contain unicast L3 frames. Since the spec says that ToDS frames must always have the BSSID as the RA (addr1), reject any other data frames. The problem was originally reported in "Predicting, Decrypting, and Abusing WPA2/802.11 Group Keys" at usenix https://www.usenix.org/conference/usenixsecurity16/technical-sessions/presentation/vanhoef and brought to my attention by Jouni. Cc: stable@vger.kernel.org Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> -- Dave, I didn't want to send you a new pull request for a single commit yet again - can you apply this one patch as is? Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-20Merge tag 'mac80211-next-for-davem-2017-04-18' of ↵David S. Miller19-162/+333
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== My last pull request has been a while, we now have: * connection quality monitoring with multiple thresholds * support for FILS shared key authentication offload * pre-CAC regulatory compliance - only ETSI allows this * sanity check for some rate confusion that hit ChromeOS (but nobody else uses it, evidently) * some documentation updates * lots of cleanups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-18mac80211: ibss: Fix channel type enum in ieee80211_sta_join_ibss()Matthias Kaehlcke1-2/+2
cfg80211_chandef_create() expects an 'enum nl80211_channel_type' as channel type however in ieee80211_sta_join_ibss() NL80211_CHAN_WIDTH_20_NOHT is passed in two occasions, which is of the enum type 'nl80211_chan_width'. Change the value to NL80211_CHAN_NO_HT (20 MHz, non-HT channel) of the channel type enum. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-18mac80211: keep a separate list of monitor interfaces that are upJohannes Berg4-12/+22
In addition to keeping monitor interfaces on the regular list of interfaces, keep those that are up and not in cooked mode on a separate list. This saves having to iterate all interfaces when delivering to monitor interfaces. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-13mac80211: fix MU-MIMO follow-MAC modeJohannes Berg1-18/+47
There are two bugs in the follow-MAC code: * it treats the radiotap header as the 802.11 header (therefore it can't possibly work) * it doesn't verify that the skb data it accesses is actually present in the header, which is mitigated by the first point Fix this by moving all of this out into a separate function. This function copies the data it needs using skb_copy_bits() to make sure it can be accessed if it's paged, and offsets that by the possibly present vendor radiotap header. This also makes all those conditions more readable. Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-13mac80211: use common code for monitor options in add/changeJohannes Berg1-58/+64
Refactor the code to have common code for changing monitor options when adding and changing virtual interfaces. This will make it easier to add BPF filters to both paths. Note that this code carefully checks the error conditions first and only then applies the changes, to guarantee atomicity. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-13cfg80211: move add/change interface monitor flags into paramsJohannes Berg1-8/+7
Instead passing both flags, which can be NULL, and vif_params, which are never NULL, move the flags into the vif_params and use BIT(0), which is invalid from userspace, to indicate that the flags were changed. While updating all drivers, fix a small bug in wil6210 where it was setting the flags to 0 instead of leaving them unchanged. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-13mac80211: correct MU-MIMO monitor follow functionalityJohannes Berg1-20/+58
The MU-MIMO monitor follow functionality is broken because it doesn't clear the MU-MIMO owner even if both follow features are disabled. Fix that, and while at it move the code into a new helper function. Call this also when creating a new monitor interface to prepare for an upcoming cfg80211 change allowing that. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-13cfg80211: allow leaving MU-MIMO monitor configuration unchangedJohannes Berg1-4/+4
When changing monitor parameters, not setting the MU-MIMO attributes should mean that they're not changed - it's documented that to turn the feature off it's necessary to set all-zero group membership and an invalid follow-address. This isn't implemented. Fix this by making the parameters pointers, stop reusing the macaddr struct member, and documenting that NULL pointers mean unchanged. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-13mac80211: drop frames too short for FCS earlierJohannes Berg1-21/+18
Instead of dropping such frames only when removing the monitor info, drop them earlier (keeping the warning) and simplify removing monitor info. While at it, make that function return void. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-13mac80211: Fix clang warning about constant operand in logical operationMatthias Kaehlcke1-2/+4
When clang detects a non-boolean constant in a logical operation it generates a 'constant-logical-operand' warning. In ieee80211_try_rate_control_ops_get() the result of strlen(<const str>) is used in a logical operation, clang resolves the expression to an (integer) constant at compile time when clang's builtin strlen function is used. Change the condition to check for strlen() > 0 to make the constant operand boolean and thus avoid the warning. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-29mac80211: unconditionally start new netdev queues with iTXQ supportJohannes Berg1-1/+2
When internal mac80211 TXQs aren't supported, netdev queues must always started out started even when driver queues are stopped while the interface is added. This is necessary because with the internal TXQ support netdev queues are never stopped and packet scheduling/dropping is done in mac80211. Cc: stable@vger.kernel.org # 4.9+ Fixes: 80a83cfc434b1 ("mac80211: skip netdev queue control with software queuing") Reported-and-tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-29mac80211: mesh: drop new node with weak powerMasashi Honma1-2/+8
On some practical cases, it is useful to drop new node in the distance. Because mesh metric is calculated with hop count and without RSSI information, a node far from local peer and near to destination node could be used as best path. For example, the nodes are located in linear. Distance of 0 - 1 and 1 - 2 and 2 - 3 is 20meters. 0 to 3 signal is very weak. 0 --- 1 --- 2 --- 3 Though most robust path from 0 to 3 is 0 -> 1 -> 2 -> 3, unfortunately, node 0 could recognize node 3 as neighbor. Then node 3 could be next of node 0. This patch aims to avoid such a case. [Johannes:] Dropping the node entirely isn't ideal, but at least with encryption there will be a limit on # of keys the hardware can deal with, and there might also be a limit on the number of stations it supports. Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-16mac80211: Use setup_timer instead of init_timer for mesh pathOndřej Lysoněk1-3/+2
Use setup_timer() and setup_deferrable_timer() to set the data and function timer fields. It makes the code cleaner and will allow for easier change of the timer struct internals. Signed-off-by: Ondřej Lysoněk <ondrej.lysonek@seznam.cz> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: <linux-wireless@vger.kernel.org> Cc: <netdev@vger.kernel.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-08mac80211: reject/clear user rate mask if not usableJohannes Berg4-1/+48
If the user rate mask results in no (basic) rates being usable, clear it. Also, if we're already operating when it's set, reject it instead. Technically, selecting basic rates as the criterion is a bit too restrictive, but calculating the usable rates over all stations (e.g. in AP mode) is harder, and all stations must support the basic rates. Similarly, in client mode, the basic rates will be used anyway for control frames. This fixes the "no supported rates (...) in rate_mask ..." warning that occurs on TX when you've selected a rate mask that's not compatible with the connection (e.g. an AP that enables only the rates 36, 48, 54 and you've selected only 6, 9, 12.) Reported-by: Kirtika Ruchandani <kirtika@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-07mac80211: remove ieee80211_tx_rate_control.max_rate_idxJohannes Berg1-8/+0
As promised a little more than 7 years ago, remove it now since nothing uses it anymore. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-07mac80211: ignore VHT membership selector when parsing ratesJohannes Berg1-5/+5
There isn't really much harm in not ignoring, since it doesn't represent a valid rate, but since we already ignore the HT one also ignore VHT. Also simplify the code a bit. Fix a typo in the related comment (pointed out by Arend) while at it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: Use setup_timer instead of init_timerOndřej Lysoněk2-12/+12
Use setup_timer() and setup_deferrable_timer() to set the data and function timer fields. It makes the code cleaner and will allow for easier change of the timer struct internals. Signed-off-by: Ondřej Lysoněk <ondrej.lysonek@seznam.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: <linux-wireless@vger.kernel.org> Cc: <netdev@vger.kernel.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: fix mesh fail_avg checkManoharan, Rajkumar1-2/+4
Mesh failure average never be more than 100. Only in case of fixed path, average will be more than threshold limit (95%). With recent EWMA changes it may go upto 99 as it is scaled to 100. It make sense to return maximum metric when average is greater than threshold limit. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: encode rate type (legacy, HT, VHT) with fewer bitsJohannes Berg2-9/+15
We don't really need three different bits for each, since the types are mutually exclusive. Use just two bits for it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: remove local pointer from rate_ctrl_refJohannes Berg2-6/+5
This pointer really isn't needed, so remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06ieee80211: rename CCFS1/CCFS2 to CCFS0/CCFS1Johannes Berg2-13/+13
This matches the spec, and otherwise things are really confusing with the next patch adding CCFS2. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: Print text for disassociation reasonArkadiusz Miskiewicz1-2/+3
When disassociation happens only numeric reason is printed in ieee80211_rx_mgmt_disassoc(). Add text variant, too. Signed-off-by: Arkadiusz Miśkiewicz <arekm@maven.pl> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: Add set_cqm_rssi_range_configAndrew Zaborowski2-0/+52
Support .set_cqm_rssi_range_config if the beacons are available for processing in mac80211. There's no reason that this couldn't be offloaded by mac80211-based drivers but there's no driver method for that added in this patch. Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: use DECLARE_EWMA for mesh_fail_avgManoharan, Rajkumar3-7/+22
As moving average is not considering fractional part, it will get stuck at the same level after certain state. For example, with current values, it can get stuck at 96. Fortunately the current threshold 95%, but if it were increased to 96 or more mesh paths would never be deactivated. Fix failure average movement by using EWMA helpers, which does take into account fractional parts. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> [johannes: pick a larger EWMA factor for more precision with the limited range that we will feed into it, adjust to new API] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds7-16/+36
Pull networking fixes from David Miller: 1) Fix double-free in batman-adv, from Sven Eckelmann. 2) Fix packet stats for fast-RX path, from Joannes Berg. 3) Netfilter's ip_route_me_harder() doesn't handle request sockets properly, fix from Florian Westphal. 4) Fix sendmsg deadlock in rxrpc, from David Howells. 5) Add missing RCU locking to transport hashtable scan, from Xin Long. 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel. 7) Fix race in NAPI handling between poll handlers and busy polling, from Eric Dumazet. 8) TX path in vxlan and geneve need proper RCU locking, from Jakub Kicinski. 9) SYN processing in DCCP and TCP need to disable BH, from Eric Dumazet. 10) Properly handle net_enable_timestamp() being invoked from IRQ context, also from Eric Dumazet. 11) Fix crash on device-tree systems in xgene driver, from Alban Bedel. 12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de Melo. 13) Fix use-after-free in netvsc driver, from Dexuan Cui. 14) Fix max MTU setting in bonding driver, from WANG Cong. 15) xen-netback hash table can be allocated from softirq context, so use GFP_ATOMIC. From Anoob Soman. 16) Fix MAC address change bug in bgmac driver, from Hari Vyas. 17) strparser needs to destroy strp_wq on module exit, from WANG Cong. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits) strparser: destroy workqueue on module exit sfc: fix IPID endianness in TSOv2 sfc: avoid max() in array size rds: remove unnecessary returned value check rxrpc: Fix potential NULL-pointer exception nfp: correct DMA direction in XDP DMA sync nfp: don't tell FW about the reserved buffer space net: ethernet: bgmac: mac address change bug net: ethernet: bgmac: init sequence bug xen-netback: don't vfree() queues under spinlock xen-netback: keep a local pointer for vif in backend_disconnect() netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups netfilter: nf_conntrack_sip: fix wrong memory initialisation can: flexcan: fix typo in comment can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer can: gs_usb: fix coding style can: gs_usb: Don't use stack memory for USB transfers ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines ixgbe: update the rss key on h/w, when ethtool ask for it ...
2017-03-02sched/headers: Prepare to use <linux/rcuupdate.h> instead of ↵Ingo Molnar1-0/+2
<linux/rculist.h> in <linux/sched.h> We don't actually need the full rculist.h header in sched.h anymore, we will be able to include the smaller rcupdate.h header instead. But first update code that relied on the implicit header inclusion. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-03 23:18:27 +0000