| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
=============================================
[ INFO: possible recursive locking detected ]
2.6.18-1.2726.fc6 #1
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
<= and => don't work well on net-endian...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up for make allyesconfig.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
The "u16 *" derefs of skb->data need to be wrapped inside of
a get_unaligned().
Thanks to Gustavo Zacarias for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Any L2CAP connection in disconnecting state shall not response
to any further config requests from the remote side. So in case
such a request is received, ignore it.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When sending a positive config response it shall include the actual
MTU to be used on this channel. This differs from the Bluetooth 1.1
specification where it was enough to acknowledge the config request.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If the RFCOMM session is no longer attached to the TTY device, then it
makes no sense to go through with changing the termios settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
After an inquiry completed or got canceled the Bluetooth core should
check for any pending connect attempts.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
To receive uvents for the low-level ACL and SCO links, they must be
assigned to a subsystem. It is enough to attach them to the already
established Bluetooth bus.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The latest HID disconnect sequence change introduced a NULL pointer
dereference. For the quirk to handle buggy remote HID implementations,
it is enough to wait for a potential control channel disconnect from
the remote side and it is also enough to wait only 500 msecs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The bt_proto array needs to be protected by some kind of locking to
prevent a race condition between bt_sock_create and bt_sock_register.
And in addition all calls to sk_alloc need to be made GFP_ATOMIC now.
Signed-off-by: Masatake YAMATO <jet@gyve.org>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If the DLC device is no longer attached to the TTY device, then it
makes no sense to go through with changing the termios settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When the connection lookup for the device structure fails, the reference
count for the HCI device needs to be decremented.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Bluetooth HID specification demands that the interrupt channel
shall be disconnected first. This is needed to pass the qualification
tests.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Most Bluetooth chips don't support concurrent connect requests, because
this would involve a multiple baseband page with only one radio. In the
case an upper layer like L2CAP requests a concurrent connect these chips
return the error "Command Disallowed" for the second request. If this
happens it the responsibility of the Bluetooth core to queue the request
and try again after the previous connect attempt has been completed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Bluetooth subsystem currently uses a platform device for devices
with no parent. It is a better idea to use the new virtual devices
tree for these.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some return values of the driver core register and create functions
are not handled and so might cause unexpected problems.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
There exists no attempt do deal with the fact that a structure with
a uint32_t followed by a pointer is going to be different for 32-bit
and 64-bit userspace. Any 32-bit process trying to use it will be
failing with -EFAULT if it's lucky; suffering from having data dumped
at a random address if it's not.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The bt_sysfs_cleanup() is marked with __exit attribute, but it will
be called from an __init function in the error case. So the __exit
attribute must be removed.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of device pairing the only safe method is to establish
a low-level ACL link. In this case, the remote side should not use
the disconnect timer to give the other side the chance to enter the
PIN code. If the disconnect timer is used, the connection will be
dropped to soon, because it is impossible to identify an actual user
of this link.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of non-blocking connects it is possible that the last user
of an ACL link quits before the connection has been fully established.
This will lead to a race condition where the internal state of a
connection is closed, but the actual link has been established and is
active. In case of Bluetooth 1.2 and later devices it is possible to
call create connection cancel to abort the connect. For older devices
the disconnect timer will be used to trigger the needed disconnect.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The local version information are needed to identify certain feature
sets of devices. They must be read on device init and stored for later
use. It is also possible to access them through the device model.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case of non-blocking socket calls we should return EINPROGRESS
and not EAGAIN.
Signed-off-by: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The command complete event of the exit periodic inquiry command must
clear the HCI_INQUIRY flag and finish the HCI request.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch assigns the next free HCI device identifier to Bluetooth
devices based on the SDIO interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch integrates the services of the Bluetooth protocols RFCOMM,
BNEP and HIDP into the driver model. This makes it possible to assign
the virtual TTY, network and input devices to a specific Bluetooth
connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch integrates the low-level connections (ACL and SCO) into the
driver model. Every connection is presented as device with the parent
set to its host controller device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch removes the unused device attribute entries for the Bluetooth
host controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some Bluetooth RFCOMM implementations try to negotiate a bigger channel
MTU than we can support for a particular session. The maximum MTU for
a RFCOMM session is limited through the L2CAP layer. So if the other
side proposes a channel MTU that is bigger than the underlying L2CAP
MTU, we should reduce it to the L2CAP MTU of the session minus five
bytes for the RFCOMM headers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Bluetooth L2CAP layer has 2 locks that are used in softirq context,
(one spinlock and one rwlock, where the softirq usage is readlock) but
where not all usages of the lock were _bh safe. The patch below corrects
this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch lets BT_HIDP depend on instead of select INPUT. This fixes
the following warning during an s390 build:
net/bluetooth/hidp/Kconfig:4:warning: 'select' used by config symbol
'BT_HIDP' refer to undefined symbol 'INPUT'
A dependency on INPUT also implies !S390 (and therefore makes the
explicit dependency obsolete) since INPUT is not available on s390.
The practical difference should be nearly zero, since INPUT is always
set to y unless EMBEDDED=y (or S390=y).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch makes the remaining transitions to use kzalloc().
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the support for RFCOMM role switching before the
connection is fully established.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the module parameter disable_cfc which can be used to
disable the credit based flow control. The credit based flow control
was introduced with the Bluetooth 1.1 specification and devices can
negotiate its support, but for testing purpose it is helpful to allow
disabling of it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch is a small cleanup of the L2CAP source code. It makes some
coding style changes and moves some functions around to avoid forward
declarations.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch converts the Bluetooth class devices into real devices. The
Bluetooth class is kept and the driver core provides the appropriate
symlinks for backward compatibility.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds a generic Bluetooth platform device that can be used
as parent device by virtual and serial devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch introduces the automatic sniff mode feature. This allows
the host to switch idle connections into sniff mode to safe power.
Signed-off-by: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch introduces a quirk that allows the drivers to tell the host
to correct the SCO buffer size values.
Signed-off-by: Olivier Galibert <galibert@pobox.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
|
|
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Also fixes all drivers that set this field.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
this fixes coverity bug id #1068.
hci_send_sco() frees skb if (skb->len > hdev->sco_mtu).
Since it returns a negative error value only in this case, we
can directly return here.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
