| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull CXL (Compute Express Link) updates from Dan Williams:
"The main new functionality this time is work to allow Linux to
natively handle CXL link protocol errors signalled via PCIe AER for
current generation CXL platforms. This required some enlightenment of
the PCIe AER core to workaround the fact that current generation RCH
(Restricted CXL Host) platforms physically hide topology details and
registers via a mechanism called RCRB (Root Complex Register Block).
The next major highlight is reworks to address bugs in parsing region
configurations for next generation VH (Virtual Host) topologies. The
old broken algorithm is replaced with a simpler one that significantly
increases the number of region configurations supported by Linux. This
is again relevant for error handling so that forward and reverse
address translation of memory errors can be carried out by Linux for
memory regions instantiated by platform firmware.
As for other cross-tree work, the ACPI table parsing code has been
refactored for reuse parsing the "CDAT" structure which is an
ACPI-like data structure that is reported by CXL devices. That work is
in preparation for v6.8 support for CXL QoS. Think of this as dynamic
generation of NUMA node topology information generated by Linux rather
than platform firmware.
Lastly, a number of internal object lifetime issues have been resolved
along with misc. fixes and feature updates (decoders_committed sysfs
ABI).
Summary:
- Add support for RCH (Restricted CXL Host) Error recovery
- Fix several region assembly bugs
- Fix mem-device lifetime issues relative to the sanitize command and
RCH topology.
- Refactor ACPI table parsing for CDAT parsing re-use in preparation
for CXL QOS support"
* tag 'cxl-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (50 commits)
lib/fw_table: Remove acpi_parse_entries_array() export
cxl/pci: Change CXL AER support check to use native AER
cxl/hdm: Remove broken error path
cxl/hdm: Fix && vs || bug
acpi: Move common tables helper functions to common lib
cxl: Add support for reading CXL switch CDAT table
cxl: Add checksum verification to CDAT from CXL
cxl: Export QTG ids from CFMWS to sysfs as qos_class attribute
cxl: Add decoders_committed sysfs attribute to cxl_port
cxl: Add cxl_decoders_committed() helper
cxl/core/regs: Rework cxl_map_pmu_regs() to use map->dev for devm
cxl/core/regs: Rename phys_addr in cxl_map_component_regs()
PCI/AER: Unmask RCEC internal errors to enable RCH downstream port error handling
PCI/AER: Forward RCH downstream port-detected errors to the CXL.mem dev handler
cxl/pci: Disable root port interrupts in RCH mode
cxl/pci: Add RCH downstream port error logging
cxl/pci: Map RCH downstream AER registers for logging protocol errors
cxl/pci: Update CXL error logging to use RAS register address
PCI/AER: Refactor cper_print_aer() for use by CXL driver module
cxl/pci: Add RCH downstream port AER register discovery
...
|
|
Pull initial bcachefs updates from Kent Overstreet:
"Here's the bcachefs filesystem pull request.
One new patch since last week: the exportfs constants ended up
conflicting with other filesystems that are also getting added to the
global enum, so switched to new constants picked by Amir.
The only new non fs/bcachefs/ patch is the objtool patch that adds
bcachefs functions to the list of noreturns. The patch that exports
osq_lock() has been dropped for now, per Ingo"
* tag 'bcachefs-2023-10-30' of https://evilpiepirate.org/git/bcachefs: (2781 commits)
exportfs: Change bcachefs fid_type enum to avoid conflicts
bcachefs: Refactor memcpy into direct assignment
bcachefs: Fix drop_alloc_keys()
bcachefs: snapshot_create_lock
bcachefs: Fix snapshot skiplists during snapshot deletion
bcachefs: bch2_sb_field_get() refactoring
bcachefs: KEY_TYPE_error now counts towards i_sectors
bcachefs: Fix handling of unknown bkey types
bcachefs: Switch to unsafe_memcpy() in a few places
bcachefs: Use struct_size()
bcachefs: Correctly initialize new buckets on device resize
bcachefs: Fix another smatch complaint
bcachefs: Use strsep() in split_devs()
bcachefs: Add iops fields to bch_member
bcachefs: Rename bch_sb_field_members -> bch_sb_field_members_v1
bcachefs: New superblock section members_v2
bcachefs: Add new helper to retrieve bch_member from sb
bcachefs: bucket_lock() is now a sleepable lock
bcachefs: fix crc32c checksum merge byte order problem
bcachefs: Fix bch2_inode_delete_keys()
...
|
|
Some of the routines in ACPI driver/acpi/tables.c can be shared with
parsing CDAT. CDAT is a device-provided data structure that is formatted
similar to a platform provided ACPI table. CDAT is used by CXL and can
exist on platforms that do not use ACPI. Split out the common routine
from ACPI to accommodate platforms that do not support ACPI and move that
to /lib. The common routines can be built outside of ACPI if
FIRMWARE_TABLES is selected.
Link: https://lore.kernel.org/linux-cxl/CAJZ5v0jipbtTNnsA0-o5ozOk8ZgWnOg34m34a9pPenTyRLj=6A@mail.gmail.com/
Suggested-by: "Rafael J. Wysocki" <rafael@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/169713683430.2205276.17899451119920103445.stgit@djiang5-mobl3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Prep work for bcachefs - being a fork of bcache it also uses closures
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
|
|
lwq is a FIFO single-linked queue that only requires a spinlock
for dequeueing, which happens in process context. Enqueueing is atomic
with no spinlock and can happen in any context.
This is particularly useful when work items are queued from BH or IRQ
context, and when they are handled one at a time by dedicated threads.
Avoiding any locking when enqueueing means there is no need to disable
BH or interrupts, which is generally best avoided (particularly when
there are any RT tasks on the machine).
This solution is superior to using "list_head" links because we need
half as many pointers in the data structures, and because list_head
lists would need locking to add items to the queue.
This solution is superior to a bespoke solution as all locking and
container_of casting is integrated, so the interface is simple.
Despite the similar name, this solution meets a distinctly different
need to kfifo. kfifo provides a fixed sized circular buffer to which
data can be added at one end and removed at the other, and does not
provide any locking. lwq does not have any size limit and works with
data structures (objects?) rather than data (bytes).
A unit test for basic functionality, which runs at boot time, is included.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Gow <davidgow@google.com>
Cc: linux-kernel@vger.kernel.org
Message-Id: <20230911111333.4d1a872330e924a00acb905b@linux-foundation.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
Replace internal logic with separate bitrev library.
Link: https://lkml.kernel.org/r/20230730081717.1498217-1-sanpeqf@gmail.com
Signed-off-by: John Sanpe <sanpeqf@gmail.com>
Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We introduce a new HAS_IOPORT Kconfig option to indicate support for I/O
Port access. In a future patch HAS_IOPORT=n will disable compilation of
the I/O accessor functions inb()/outb() and friends on architectures
which can not meaningfully support legacy I/O spaces such as s390.
The following architectures do not select HAS_IOPORT:
* ARC
* C-SKY
* Hexagon
* Nios II
* OpenRISC
* s390
* User-Mode Linux
* Xtensa
All other architectures select HAS_IOPORT at least conditionally.
The "depends on" relations on HAS_IOPORT in drivers as well as ifdefs
for HAS_IOPORT specific sections will be added in subsequent patches on
a per subsystem basis.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net> # for ARCH=um
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd
Pull iommufd implementation from Jason Gunthorpe:
"iommufd is the user API to control the IOMMU subsystem as it relates
to managing IO page tables that point at user space memory.
It takes over from drivers/vfio/vfio_iommu_type1.c (aka the VFIO
container) which is the VFIO specific interface for a similar idea.
We see a broad need for extended features, some being highly IOMMU
device specific:
- Binding iommu_domain's to PASID/SSID
- Userspace IO page tables, for ARM, x86 and S390
- Kernel bypassed invalidation of user page tables
- Re-use of the KVM page table in the IOMMU
- Dirty page tracking in the IOMMU
- Runtime Increase/Decrease of IOPTE size
- PRI support with faults resolved in userspace
Many of these HW features exist to support VM use cases - for instance
the combination of PASID, PRI and Userspace IO Page Tables allows an
implementation of DMA Shared Virtual Addressing (vSVA) within a guest.
Dirty tracking enables VM live migration with SRIOV devices and PASID
support allow creating "scalable IOV" devices, among other things.
As these features are fundamental to a VM platform they need to be
uniformly exposed to all the driver families that do DMA into VMs,
which is currently VFIO and VDPA"
For more background, see the extended explanations in Jason's pull request:
https://lore.kernel.org/lkml/Y5dzTU8dlmXTbzoJ@nvidia.com/
* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd: (62 commits)
iommufd: Change the order of MSI setup
iommufd: Improve a few unclear bits of code
iommufd: Fix comment typos
vfio: Move vfio group specific code into group.c
vfio: Refactor dma APIs for emulated devices
vfio: Wrap vfio group module init/clean code into helpers
vfio: Refactor vfio_device open and close
vfio: Make vfio_device_open() truly device specific
vfio: Swap order of vfio_device_container_register() and open_device()
vfio: Set device->group in helper function
vfio: Create wrappers for group register/unregister
vfio: Move the sanity check of the group to vfio_create_group()
vfio: Simplify vfio_create_group()
iommufd: Allow iommufd to supply /dev/vfio/vfio
vfio: Make vfio_container optionally compiled
vfio: Move container related MODULE_ALIAS statements into container.c
vfio-iommufd: Support iommufd for emulated VFIO devices
vfio-iommufd: Support iommufd for physical VFIO devices
vfio-iommufd: Allow iommufd to be used in place of a container fd
vfio: Use IOMMU_CAP_ENFORCE_CACHE_COHERENCY for vfio_file_enforced_coherent()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- A ptrace API cleanup series from Sergey Shtylyov
- Fixes and cleanups for kexec from ye xingchen
- nilfs2 updates from Ryusuke Konishi
- squashfs feature work from Xiaoming Ni: permit configuration of the
filesystem's compression concurrency from the mount command line
- A series from Akinobu Mita which addresses bound checking errors when
writing to debugfs files
- A series from Yang Yingliang to address rapidio memory leaks
- A series from Zheng Yejian to address possible overflow errors in
encode_comp_t()
- And a whole shower of singleton patches all over the place
* tag 'mm-nonmm-stable-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (79 commits)
ipc: fix memory leak in init_mqueue_fs()
hfsplus: fix bug causing custom uid and gid being unable to be assigned with mount
rapidio: devices: fix missing put_device in mport_cdev_open
kcov: fix spelling typos in comments
hfs: Fix OOB Write in hfs_asc2mac
hfs: fix OOB Read in __hfs_brec_find
relay: fix type mismatch when allocating memory in relay_create_buf()
ocfs2: always read both high and low parts of dinode link count
io-mapping: move some code within the include guarded section
kernel: kcsan: kcsan_test: build without structleak plugin
mailmap: update email for Iskren Chernev
eventfd: change int to __u64 in eventfd_signal() ifndef CONFIG_EVENTFD
rapidio: fix possible UAF when kfifo_alloc() fails
relay: use strscpy() is more robust and safer
cpumask: limit visibility of FORCE_NR_CPUS
acct: fix potential integer overflow in encode_comp_t()
acct: fix accuracy loss for input value of encode_comp_t()
linux/init.h: include <linux/build_bug.h> and <linux/stringify.h>
rapidio: rio: fix possible name leak in rio_register_mport()
rapidio: fix possible name leaks when rio_add_device() fails
...
|
|
Remove bit_reverse() function. Instead use bitrev8() from linux/bitrev.h +
bitshift. Reduces code-repetition.
Signed-off-by: Uladzislau Koshchanka <koshchanka@gmail.com>
Link: https://lore.kernel.org/r/20221210004423.32332-1-koshchanka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In current form, FORCE_NR_CPUS is visible to all users building their
kernels, even not experts. It is also set in allmodconfig or
allyesconfig, which is not a correct behavior.
This patch fixes it. It also changes the parameter short description:
removes implementation details and highlights the effect of the change.
Link: https://lkml.kernel.org/r/20221116172451.274938-1-yury.norov@gmail.com
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Cc: Alexey Klimov <klimov.linux@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Sander Vanheule <sander@svanheule.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The span iterator travels over the indexes of the interval_tree, not the
nodes, and classifies spans of indexes as either 'used' or 'hole'.
'used' spans are fully covered by nodes in the tree and 'hole' spans have
no node intersecting the span.
This is done greedily such that spans are maximally sized and every
iteration step switches between used/hole.
As an example a trivial allocator can be written as:
for (interval_tree_span_iter_first(&span, itree, 0, ULONG_MAX);
!interval_tree_span_iter_done(&span);
interval_tree_span_iter_next(&span))
if (span.is_hole &&
span.last_hole - span.start_hole >= allocation_size - 1)
return span.start_hole;
With all the tricky boundary conditions handled by the library code.
The following iommufd patches have several algorithms for its overlapping
node interval trees that are significantly simplified with this kind of
iteration primitive. As it seems generally useful, put it into lib/.
Link: https://lore.kernel.org/r/3-v6-a196d26f289e+11787-iommufd_jgg@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Yi Liu <yi.l.liu@intel.com>
Tested-by: Lixiao Yang <lixiao.yang@intel.com>
Tested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
With CXL security features, and CXL dynamic provisioning, global CPU
cache flushing nvdimm requirements are no longer specific to that
subsystem, even beyond the scope of security_ops. CXL will need such
semantics for features not necessarily limited to persistent memory.
The functionality this is enabling is to be able to instantaneously
secure erase potentially terabytes of memory at once and the kernel
needs to be sure that none of the data from before the erase is still
present in the cache. It is also used when unlocking a memory device
where speculative reads and firmware accesses could have cached poison
from before the device was unlocked. Lastly this facility is used when
mapping new devices, or new capacity into an established physical
address range. I.e. when the driver switches DeviceA mapping AddressX to
DeviceB mapping AddressX then any cached data from DeviceA:AddressX
needs to be invalidated.
This capability is typically only used once per-boot (for unlock), or
once per bare metal provisioning event (secure erase), like when handing
off the system to another tenant or decommissioning a device. It may
also be used for dynamic CXL region provisioning.
Users must first call cpu_cache_has_invalidate_memregion() to know
whether this functionality is available on the architecture. On x86 this
respects the constraints of when wbinvd() is tolerable. It is already
the case that wbinvd() is problematic to allow in VMs due its global
performance impact and KVM, for example, has been known to just trap and
ignore the call. With confidential computing guest execution of wbinvd()
may even trigger an exception. Given guests should not be messing with
the bare metal address map via CXL configuration changes
cpu_cache_has_invalidate_memregion() returns false in VMs.
While this global cache invalidation facility, is exported to modules,
since NVDIMM and CXL support can be built as a module, it is not for
general use. The intent is that this facility is not available outside
of specific "device-memory" use cases. To make that expectation as clear
as possible the API is scoped to a new "DEVMEM" module namespace that
only the NVDIMM and CXL subsystems are expected to import.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: x86@kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Feed untrusted RNGs into /dev/random
- Allow HWRNG sleeping to be more interruptible
- Create lib/utils module
- Setting private keys no longer required for akcipher
- Remove tcrypt mode=1000
- Reorganised Kconfig entries
Algorithms:
- Load x86/sha512 based on CPU features
- Add AES-NI/AVX/x86_64/GFNI assembler implementation of aria cipher
Drivers:
- Add HACE crypto driver aspeed"
* tag 'v6.1-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (124 commits)
crypto: aspeed - Remove redundant dev_err call
crypto: scatterwalk - Remove unused inline function scatterwalk_aligned()
crypto: aead - Remove unused inline functions from aead
crypto: bcm - Simplify obtain the name for cipher
crypto: marvell/octeontx - use sysfs_emit() to instead of scnprintf()
hwrng: core - start hwrng kthread also for untrusted sources
crypto: zip - remove the unneeded result variable
crypto: qat - add limit to linked list parsing
crypto: octeontx2 - Remove the unneeded result variable
crypto: ccp - Remove the unneeded result variable
crypto: aspeed - Fix check for platform_get_irq() errors
crypto: virtio - fix memory-leak
crypto: cavium - prevent integer overflow loading firmware
crypto: marvell/octeontx - prevent integer overflows
crypto: aspeed - fix build error when only CRYPTO_DEV_ASPEED is enabled
crypto: hisilicon/qm - fix the qos value initialization
crypto: sun4i-ss - use DEFINE_SHOW_ATTRIBUTE to simplify sun4i_ss_debugfs
crypto: tcrypt - add async speed test for aria cipher
crypto: aria-avx - add AES-NI/AVX/x86_64/GFNI assembler implementation of aria cipher
crypto: aria - prepare generic module for optimized implementations
...
|
|
Pull bitmap updates from Yury Norov:
- Fix unsigned comparison to -1 in CPUMAP_FILE_MAX_BYTES (Phil Auld)
- cleanup nr_cpu_ids vs nr_cpumask_bits mess (me)
This series cleans that mess and adds new config FORCE_NR_CPUS that
allows to optimize cpumask subsystem if the number of CPUs is known
at compile-time.
- optimize find_bit() functions (me)
Reworks find_bit() functions based on new FIND_{FIRST,NEXT}_BIT()
macros.
- add find_nth_bit() (me)
Adds find_nth_bit(), which is ~70 times faster than bitcounting with
for_each() loop:
for_each_set_bit(bit, mask, size)
if (n-- == 0)
return bit;
Also adds bitmap_weight_and() to let people replace this pattern:
tmp = bitmap_alloc(nbits);
bitmap_and(tmp, map1, map2, nbits);
weight = bitmap_weight(tmp, nbits);
bitmap_free(tmp);
with a single bitmap_weight_and() call.
- repair cpumask_check() (me)
After switching cpumask to use nr_cpu_ids, cpumask_check() started
generating many false-positive warnings. This series fixes it.
- Add for_each_cpu_andnot() and for_each_cpu_andnot() (Valentin
Schneider)
Extends the API with one more function and applies it in sched/core.
* tag 'bitmap-6.1-rc1' of https://github.com/norov/linux: (28 commits)
sched/core: Merge cpumask_andnot()+for_each_cpu() into for_each_cpu_andnot()
lib/test_cpumask: Add for_each_cpu_and(not) tests
cpumask: Introduce for_each_cpu_andnot()
lib/find_bit: Introduce find_next_andnot_bit()
cpumask: fix checking valid cpu range
lib/bitmap: add tests for for_each() loops
lib/find: optimize for_each() macros
lib/bitmap: introduce for_each_set_bit_wrap() macro
lib/find_bit: add find_next{,_and}_bit_wrap
cpumask: switch for_each_cpu{,_not} to use for_each_bit()
net: fix cpu_max_bits_warn() usage in netif_attrmask_next{,_and}
cpumask: add cpumask_nth_{,and,andnot}
lib/bitmap: remove bitmap_ord_to_pos
lib/bitmap: add tests for find_nth_bit()
lib: add find_nth{,_and,_andnot}_bit()
lib/bitmap: add bitmap_weight_and()
lib/bitmap: don't call __bitmap_weight() in kernel code
tools: sync find_bit() implementation
lib/find_bit: optimize find_next_bit() functions
lib/find_bit: create find_first_zero_bit_le()
...
|
|
With CONFIG_ZSTD_COMPRESS=m and CONFIG_ZSTD_DECOMPRESS=y we end up in
a situation when files from lib/zstd/common/ are compiled once to be
linked later for ZSTD_DECOMPRESS (build-in) and ZSTD_COMPRESS (module)
even though CFLAGS are different for builtins and modules.
So far somehow this was not a problem but enabling LLVM LTO exposes
the problem as:
ld.lld: error: linking module flags 'Code Model': IDs have conflicting values in 'lib/built-in.a(zstd_common.o at 5868)' and 'ld-temp.o'
This particular conflict is caused by KBUILD_CFLAGS=-mcmodel=medium vs.
KBUILD_CFLAGS_MODULE=-mcmodel=large , modules use the large model on
POWERPC as explained at
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/powerpc/Makefile?h=v5.18-rc4#n127
but the current use of common files is wrong anyway.
This works around the issue by introducing a zstd_common module with
shared code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
The size of cpumasks is hard-limited by compile-time parameter NR_CPUS,
but defined at boot-time when kernel parses ACPI/DT tables, and stored in
nr_cpu_ids. In many practical cases, number of CPUs for a target is known
at compile time, and can be provided with NR_CPUS.
In that case, compiler may be instructed to rely on NR_CPUS as on actual
number of CPUs, not an upper limit. It allows to optimize many cpumask
routines and significantly shrink size of the kernel image.
This patch adds FORCE_NR_CPUS option to teach the compiler to rely on
NR_CPUS and enable corresponding optimizations.
If FORCE_NR_CPUS=y, kernel will not set nr_cpu_ids at boot, but only check
that the actual number of possible CPUs is equal to NR_CPUS, and WARN if
that doesn't hold.
The new option is especially useful in embedded applications because
kernel configurations are unique for each SoC, the number of CPUs is
constant and known well, and memory limitations are typically harder.
For my 4-CPU ARM64 build with NR_CPUS=4, FORCE_NR_CPUS=y saves 46KB:
add/remove: 3/4 grow/shrink: 46/729 up/down: 652/-46952 (-46300)
Signed-off-by: Yury Norov <yury.norov@gmail.com>
|
|
As requested at
https://lore.kernel.org/r/YtEgzHuuMts0YBCz@gondor.apana.org.au, move
__crypto_memneq into lib/crypto/ and put it under a new tristate. The
tristate is CRYPTO_LIB_UTILS, and it builds a module libcryptoutils. As
more crypto library utilities are being added, this creates a single
place for them to go without cluttering up the main lib directory.
The module's main file will be lib/crypto/utils.c. However, leave
memneq.c as its own file because of its nonstandard license.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc updates from Andrew Morton:
"Updates to various subsystems which I help look after. lib, ocfs2,
fatfs, autofs, squashfs, procfs, etc. A relatively small amount of
material this time"
* tag 'mm-nonmm-stable-2022-08-06-2' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (72 commits)
scripts/gdb: ensure the absolute path is generated on initial source
MAINTAINERS: kunit: add David Gow as a maintainer of KUnit
mailmap: add linux.dev alias for Brendan Higgins
mailmap: update Kirill's email
profile: setup_profiling_timer() is moslty not implemented
ocfs2: fix a typo in a comment
ocfs2: use the bitmap API to simplify code
ocfs2: remove some useless functions
lib/mpi: fix typo 'the the' in comment
proc: add some (hopefully) insightful comments
bdi: remove enum wb_congested_state
kernel/hung_task: fix address space of proc_dohung_task_timeout_secs
lib/lzo/lzo1x_compress.c: replace ternary operator with min() and min_t()
squashfs: support reading fragments in readahead call
squashfs: implement readahead
squashfs: always build "file direct" version of page actor
Revert "squashfs: provide backing_dev_info in order to disable read-ahead"
fs/ocfs2: Fix spelling typo in comment
ia64: old_rr4 added under CONFIG_HUGETLB_PAGE
proc: fix test for "vsyscall=xonly" boot option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic version
of the MMIO accessors, which is intended to help understand
problems with device drivers and has been part of Qualcomm's vendor
kernels for many years
- A patch from Sebastian Siewior to rework the handling of IRQ stacks
in softirqs across architectures, which is needed for enabling
PREEMPT_RT
- The last patch to remove the CONFIG_VIRT_TO_BUS option and some of
the code behind that, after the last users of this old interface
made it in through the netdev, scsi, media and staging trees"
* tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
uapi: asm-generic: fcntl: Fix typo 'the the' in comment
arch/*/: remove CONFIG_VIRT_TO_BUS
soc: qcom: geni: Disable MMIO tracing for GENI SE
serial: qcom_geni_serial: Disable MMIO tracing for geni serial
asm-generic/io: Add logging support for MMIO accessors
KVM: arm64: Add a flag to disable MMIO trace for nVHE KVM
lib: Add register read/write tracing support
drm/meson: Fix overflow implicit truncation warnings
irqchip/tegra: Fix overflow implicit truncation warnings
coresight: etm4x: Use asm-generic IO memory barriers
arm64: io: Use asm-generic high level MMIO accessors
arch/*: Disable softirq stacks on PREEMPT_RT.
|
|
As Linus explained [1], setting the stackdepot hash table size as a config
option is suboptimal, especially as stackdepot becomes a dependency of
less "expert" subsystems than initially (e.g. DRM, networking,
SLUB_DEBUG):
: (a) it introduces a new compile-time question that isn't sane to ask
: a regular user, but is now exposed to regular users.
: (b) this by default uses 1MB of memory for a feature that didn't in
: the past, so now if you have small machines you need to make sure you
: make a special kernel config for them.
Ideally we would employ rhashtable for fully automatic resizing, which
should be feasible for many of the new users, but problematic for the
original users with restricted context that call __stack_depot_save() with
can_alloc == false, i.e. KASAN.
However we can easily remove the config option and scale the hash table
automatically with system memory. The STACK_HASH_MASK constant becomes
stack_hash_mask variable and is used only in one mask operation, so the
overhead should be negligible to none. For early allocation we can employ
the existing alloc_large_system_hash() function and perform similar
scaling for the late allocation.
The existing limits of the config option (between 4k and 1M buckets) are
preserved, and scaling factor is set to one bucket per 16kB memory so on
64bit the max 1M buckets (8MB memory) is achieved with 16GB system, while
a 1GB system will use 512kB.
Because KASAN is reported to need the maximum number of buckets even with
smaller amounts of memory [2], set it as such when kasan_enabled().
If needed, the automatic scaling could be complemented with a boot-time
kernel parameter, but it feels pointless to add it without a specific use
case.
[1] https://lore.kernel.org/all/CAHk-=wjC5nS+fnf6EzRD9yQRJApAhxx7gRB87ZV+pAWo9oVrTg@mail.gmail.com/
[2] https://lore.kernel.org/all/CACT4Y+Y4GZfXOru2z5tFPzFdaSUd+GFc6KVL=bsa0+1m197cQQ@mail.gmail.com/
Link: https://lkml.kernel.org/r/20220620150249.16814-1-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Generic MMIO read/write i.e., __raw_{read,write}{b,l,w,q} accessors
are typically used to read/write from/to memory mapped registers
and can cause hangs or some undefined behaviour in following few
cases,
* If the access to the register space is unclocked, for example: if
there is an access to multimedia(MM) block registers without MM
clocks.
* If the register space is protected and not set to be accessible from
non-secure world, for example: only EL3 (EL: Exception level) access
is allowed and any EL2/EL1 access is forbidden.
* If xPU(memory/register protection units) is controlling access to
certain memory/register space for specific clients.
and more...
Such cases usually results in instant reboot/SErrors/NOC or interconnect
hangs and tracing these register accesses can be very helpful to debug
such issues during initial development stages and also in later stages.
So use ftrace trace events to log such MMIO register accesses which
provides rich feature set such as early enablement of trace events,
filtering capability, dumping ftrace logs on console and many more.
Sample output:
rwmmio_write: __qcom_geni_serial_console_write+0x160/0x1e0 width=32 val=0xa0d5d addr=0xfffffbfffdbff700
rwmmio_post_write: __qcom_geni_serial_console_write+0x160/0x1e0 width=32 val=0xa0d5d addr=0xfffffbfffdbff700
rwmmio_read: qcom_geni_serial_poll_bit+0x94/0x138 width=32 addr=0xfffffbfffdbff610
rwmmio_post_read: qcom_geni_serial_poll_bit+0x94/0x138 width=32 val=0x0 addr=0xfffffbfffdbff610
Co-developed-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This is used by code that doesn't need CONFIG_CRYPTO, so move this into
lib/ with a Kconfig option so that it can be selected by whatever needs
it.
This fixes a linker error Zheng pointed out when
CRYPTO_MANAGER_DISABLE_TESTS!=y and CRYPTO=m:
lib/crypto/curve25519-selftest.o: In function `curve25519_selftest':
curve25519-selftest.c:(.init.text+0x60): undefined reference to `__crypto_memneq'
curve25519-selftest.c:(.init.text+0xec): undefined reference to `__crypto_memneq'
curve25519-selftest.c:(.init.text+0x114): undefined reference to `__crypto_memneq'
curve25519-selftest.c:(.init.text+0x154): undefined reference to `__crypto_memneq'
Reported-by: Zheng Bin <zhengbin13@huawei.com>
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: stable@vger.kernel.org
Fixes: aa127963f1ca ("crypto: lib/curve25519 - re-add selftests")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Some temperature and voltage sensors use a polynomial to convert between
raw data points and actual temperature or voltage. The polynomial is
usually the result of a curve fitting of the diode characteristic.
The BT1 PVT hwmon driver already uses such a polynonmial calculation
which is rather generic. Move it to lib/ so other drivers can reuse it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-2-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Hardware specific features may be able to calculate a crc64, so provide
a framework for drivers to register their implementation. If nothing is
registered, fallback to the generic table lookup implementation. The
implementation is modeled after the crct10dif equivalent.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20220303201312.3255347-7-kbusch@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull ARM fixes from Russell King:
- Fix kgdb breakpoint for Thumb2
- Fix dependency for BITREVERSE kconfig
- Fix nommu early_params and __setup returns
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9182/1: mmu: fix returns from early_param() and __setup() functions
ARM: 9178/1: fix unmet dependency on BITREVERSE for HAVE_ARCH_BITREVERSE
ARM: Fix kgdb breakpoint for Thumb2
|
|
Resending this to properly add it to the patch tracker - thanks for letting
me know, Arnd :)
When ARM is enabled, and BITREVERSE is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for HAVE_ARCH_BITREVERSE
Depends on [n]: BITREVERSE [=n]
Selected by [y]:
- ARM [=y] && (CPU_32v7M [=n] || CPU_32v7 [=y]) && !CPU_32v6 [=n]
This is because ARM selects HAVE_ARCH_BITREVERSE
without selecting BITREVERSE, despite
HAVE_ARCH_BITREVERSE depending on BITREVERSE.
This unmet dependency bug was found by Kismet,
a static analysis tool for Kconfig. Please advise if this
is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
|
|
Currently, enabling CONFIG_STACKDEPOT means its stack_table will be
allocated from memblock, even if stack depot ends up not actually used.
The default size of stack_table is 4MB on 32-bit, 8MB on 64-bit.
This is fine for use-cases such as KASAN which is also a config option
and has overhead on its own. But it's an issue for functionality that
has to be actually enabled on boot (page_owner) or depends on hardware
(GPU drivers) and thus the memory might be wasted. This was raised as
an issue [1] when attempting to add stackdepot support for SLUB's debug
object tracking functionality. It's common to build kernels with
CONFIG_SLUB_DEBUG and enable slub_debug on boot only when needed, or
create only specific kmem caches with debugging for testing purposes.
It would thus be more efficient if stackdepot's table was allocated only
when actually going to be used. This patch thus makes the allocation
(and whole stack_depot_init() call) optional:
- Add a CONFIG_STACKDEPOT_ALWAYS_INIT flag to keep using the current
well-defined point of allocation as part of mem_init(). Make
CONFIG_KASAN select this flag.
- Other users have to call stack_depot_init() as part of their own init
when it's determined that stack depot will actually be used. This may
depend on both config and runtime conditions. Convert current users
which are page_owner and several in the DRM subsystem. Same will be
done for SLUB later.
- Because the init might now be called after the boot-time memblock
allocation has given all memory to the buddy allocator, change
stack_depot_init() to allocate stack_table with kvmalloc() when
memblock is no longer available. Also handle allocation failure by
disabling stackdepot (could have theoretically happened even with
memblock allocation previously), and don't unnecessarily align the
memblock allocation to its own size anymore.
[1] https://lore.kernel.org/all/CAMuHMdW=eoVzM1Re5FVoEN87nKfiLmM2+Ah7eNu2KXEhCvbZyA@mail.gmail.com/
Link: https://lkml.kernel.org/r/20211013073005.11351-1-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Marco Elver <elver@google.com> # stackdepot
Cc: Marco Elver <elver@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Imran Khan <imran.f.khan@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
Subject: lib/stackdepot: fix spelling mistake and grammar in pr_err message
There is a spelling mistake of the work allocation so fix this and
re-phrase the message to make it easier to read.
Link: https://lkml.kernel.org/r/20211015104159.11282-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup
On FLATMEM, we call page_ext_init_flatmem_late() just before
kmem_cache_init() which means stack_depot_init() (called by page owner
init) will not recognize properly it should use kvmalloc() and not
memblock_alloc(). memblock_alloc() will also not issue a warning and
return a block memory that can be invalid and cause kernel page fault when
saving stacks, as reported by the kernel test robot [1].
Fix this by moving page_ext_init_flatmem_late() below kmem_cache_init() so
that slab_is_available() is true during stack_depot_init(). SPARSEMEM
doesn't have this issue, as it doesn't do page_ext_init_flatmem_late(),
but a different page_ext_init() even later in the boot process.
Thanks to Mike Rapoport for pointing out the FLATMEM init ordering issue.
While at it, also actually resolve a checkpatch warning in stack_depot_init()
from DRM CI, which was supposed to be in the original patch already.
[1] https://lore.kernel.org/all/20211014085450.GC18719@xsang-OptiPlex-9020/
Link: https://lkml.kernel.org/r/6abd9213-19a9-6d58-cedc-2414386d2d81@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: kernel test robot <oliver.sang@intel.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup3
Due to cd06ab2fd48f ("drm/locking: add backtrace for locking contended
locks without backoff") landing recently to -next adding a new stack depot
user in drivers/gpu/drm/drm_modeset_lock.c we need to add an appropriate
call to stack_depot_init() there as well.
Link: https://lkml.kernel.org/r/2a692365-cfa1-64f2-34e0-8aa5674dce5e@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Marco Elver <elver@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Imran Khan <imran.f.khan@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup4
Due to 4e66934eaadc ("lib: add reference counting tracking
infrastructure") landing recently to net-next adding a new stack depot
user in lib/ref_tracker.c we need to add an appropriate call to
stack_depot_init() there as well.
Link: https://lkml.kernel.org/r/45c1b738-1a2f-5b5f-2f6d-86fab206d01c@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Slab <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 6048fdcc5f269 ("lib/crypto: blake2s: include as built-in") took
away a number of prompt texts from other crypto libraries. This makes
values flip from built-in to module when oldconfig runs, and causes
problems when these crypto libs need to be built in for thingslike
BIG_KEYS.
Fixes: 6048fdcc5f269 ("lib/crypto: blake2s: include as built-in")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Justin M. Forbes <jforbes@fedoraproject.org>
[Jason: - moved menu into submenu of lib/ instead of root menu
- fixed chacha sub-dependencies for CONFIG_CRYPTO]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
In 5.12 cycle we enabled GENERIC_FIND_FIRST_BIT config option for ARM64
and MIPS. It increased performance and shrunk .text size; and so far
I didn't receive any negative feedback on the change.
https://lore.kernel.org/linux-arch/20210225135700.1381396-1-yury.norov@gmail.com/
Now I think it's a good time to switch all architectures to use
find_{first,last}_bit() unconditionally, and so remove corresponding
config option.
The patch does't introduce functioal changes for arc, arm, arm64, mips,
m68k, s390 and x86, for other architectures I expect improvement both in
performance and .text size.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Alexander Lobakin <alobakin@pm.me> (mips)
Reviewed-by: Alexander Lobakin <alobakin@pm.me> (mips)
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Will Deacon <will@kernel.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
It can be hard to track where references are taken and released.
In networking, we have annoying issues at device or netns dismantles,
and we had various proposals to ease root causing them.
This patch adds new infrastructure pairing refcount increases
and decreases. This will self document code, because programmers
will have to associate increments/decrements.
This is controled by CONFIG_REF_TRACKER which can be selected
by users of this feature.
This adds both cpu and memory costs, and thus should probably be
used with care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The main content for 5.15 is a series that cleans up the handling of
strncpy_from_user() and strnlen_user(), removing a lot of slightly
incorrect versions of these in favor of the lib/strn*.c helpers that
implement these correctly and more efficiently.
The only architectures that retain a private version now are mips,
ia64, um and parisc. I had offered to convert those at all, but Thomas
Bogendoerfer wanted to keep the mips version for the moment until he
had a chance to do regression testing.
The branch also contains two patches for bitops and for ffs()"
* tag 'asm-generic-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
bitops/non-atomic: make @nr unsigned to avoid any DIV
asm-generic: ffs: Drop bogus reference to ffz location
asm-generic: reverse GENERIC_{STRNCPY_FROM,STRNLEN}_USER symbols
asm-generic: remove extra strn{cpy_from,len}_user declarations
asm-generic: uaccess: remove inline strncpy_from_user/strnlen_user
s390: use generic strncpy/strnlen from_user
microblaze: use generic strncpy/strnlen from_user
csky: use generic strncpy/strnlen from_user
arc: use generic strncpy/strnlen from_user
hexagon: use generic strncpy/strnlen from_user
h8300: remove stale strncpy_from_user
asm-generic/uaccess.h: remove __strncpy_from_user/__strnlen_user
|
|
STRING_SELFTEST is presented in the "Library routines" menu. Move it in
Kernel hacking > Kernel Testing and Coverage > Runtime Testing together
with other similar tests found in lib/
--- Runtime Testing
<*> Test functions located in the hexdump module at runtime
<*> Test string functions (NEW)
<*> Test functions located in the string_helpers module at runtime
<*> Test strscpy*() family of functions at runtime
<*> Test kstrto*() family of functions at runtime
<*> Test printf() family of functions at runtime
<*> Test scanf() family of functions at runtime
Link: https://lkml.kernel.org/r/20210719185158.190371-1-mcroce@linux.microsoft.com
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Most architectures do not need a custom implementation, and in most
cases the generic implementation is preferred, so change the polariy
on these Kconfig symbols to require architectures to select them when
they provide their own version.
The new name is CONFIG_ARCH_HAS_{STRNCPY_FROM,STRNLEN}_USER.
The remaining architectures at the moment are: ia64, mips, parisc,
um and xtensa. We should probably convert these as well, but
I was not sure how far to take this series. Thomas Bogendoerfer
had some concerns about converting mips but may still do some
more detailed measurements to see which version is better.
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-um@lists.infradead.org
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add IO memory emulation that uses callbacks for read/write to
the allocated regions. The callbacks can be registered by the
users using logic_iomem_alloc().
To use, an architecture must 'select LOGIC_IOMEM' in Kconfig
and then include <asm-generic/logic_io.h> into asm/io.h to get
the __raw_read*/__raw_write* functions.
Optionally, an architecture may 'select LOGIC_IOMEM_FALLBACK'
in which case non-emulated regions will 'fall back' to the
various real_* functions that must then be provided.
Cc: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
We have a need in the TPM2 trusted keys to return the ASN.1 form of the TPM
key blob so it can be operated on by tools outside of the kernel. The
specific tools are the openssl_tpm2_engine, openconnect and the Intel
tpm2-tss-engine. To do that, we have to be able to read and write the same
binary key format the tools use. The current ASN.1 decoder does fine for
reading, but we need pieces of an ASN.1 encoder to write the key blob in
binary compatible form.
For backwards compatibility, the trusted key reader code will still accept
the two TPM2B quantities that it uses today, but the writer will only
output the ASN.1 form.
The current implementation only encodes the ASN.1 bits we actually need.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Use CONFIG_STACK_HASH_ORDER to configure STACK_HASH_SIZE.
Aim is to have configurable value for STACK_HASH_SIZE,
so depend on use case one can configure it.
One example is of Page Owner, CONFIG_PAGE_OWNER works only if
page_owner=on via kernel parameter on CONFIG_PAGE_OWNER configured system.
Thus, unless admin enable it via command line option, the stackdepot will
just waste 8M memory without any customer.
Making it configurable and use lower value helps to enable features like
CONFIG_PAGE_OWNER without any significant overhead.
Link: https://lkml.kernel.org/r/1611749198-24316-1-git-send-email-vjitta@codeaurora.org
Signed-off-by: Yogesh Lal <ylal@codeaurora.org>
Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org>
Signed-off-by: Vijayanand Jitta <vjitta@codeaurora.org>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As part of adding STRICT_DEVMEM support to the RISC-V port, Zong provided an
implementation of devmem_is_allowed() that's exactly the same as the version in
a handful of other ports. Rather than duplicate code, I've put a generic
version of this in lib/ and used it for the RISC-V port.
* palmer/generic-devmem:
arm64: Use the generic devmem_is_allowed()
arm: Use the generic devmem_is_allowed()
RISC-V: Use the new generic devmem_is_allowed()
lib: Add a generic version of devmem_is_allowed()
|
|
As part of adding support for STRICT_DEVMEM to the RISC-V port, Zong
provided a devmem_is_allowed() implementation that's exactly the same as
all the others I checked. Instead I'm adding a generic version, which
will soon be used.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
In reaction to a proposal to introduce a memcpy_mcsafe_fast()
implementation Linus points out that memcpy_mcsafe() is poorly named
relative to communicating the scope of the interface. Specifically what
addresses are valid to pass as source, destination, and what faults /
exceptions are handled.
Of particular concern is that even though x86 might be able to handle
the semantics of copy_mc_to_user() with its common copy_user_generic()
implementation other archs likely need / want an explicit path for this
case:
On Fri, May 1, 2020 at 11:28 AM Linus Torvalds <torvalds@linux-foundation.org> wrote:
>
> On Thu, Apr 30, 2020 at 6:21 PM Dan Williams <dan.j.williams@intel.com> wrote:
> >
> > However now I see that copy_user_generic() works for the wrong reason.
> > It works because the exception on the source address due to poison
> > looks no different than a write fault on the user address to the
> > caller, it's still just a short copy. So it makes copy_to_user() work
> > for the wrong reason relative to the name.
>
> Right.
>
> And it won't work that way on other architectures. On x86, we have a
> generic function that can take faults on either side, and we use it
> for both cases (and for the "in_user" case too), but that's an
> artifact of the architecture oddity.
>
> In fact, it's probably wrong even on x86 - because it can hide bugs -
> but writing those things is painful enough that everybody prefers
> having just one function.
Replace a single top-level memcpy_mcsafe() with either
copy_mc_to_user(), or copy_mc_to_kernel().
Introduce an x86 copy_mc_fragile() name as the rename for the
low-level x86 implementation formerly named memcpy_mcsafe(). It is used
as the slow / careful backend that is supplanted by a fast
copy_mc_generic() in a follow-on patch.
One side-effect of this reorganization is that separating copy_mc_64.S
to its own file means that perf no longer needs to track dependencies
for its memcpy_64.S benchmarks.
[ bp: Massage a bit. ]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Link: http://lore.kernel.org/r/CAHk-=wjSqtXAqfUJxFtWNwmguFASTgB0dz1dT3V-78Quiezqbg@mail.gmail.com
Link: https://lkml.kernel.org/r/160195561680.2163339.11574962055305783722.stgit@dwillia2-desk3.amr.corp.intel.com
|
|
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
|
|
- Add unzstd() and the zstd decompress interface.
- Add zstd support to decompress_method().
The decompress_method() and unzstd() functions are used to decompress
the initramfs and the initrd. The __decompress() function is used in
the preboot environment to decompress a zstd compressed kernel.
The zstd decompression function allows the input and output buffers to
overlap because that is used by x86 kernel decompression.
Signed-off-by: Nick Terrell <terrelln@fb.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200730190841.2071656-3-nickrterrell@gmail.com
|
|
The pldmfw library is used to implement common logic needed to flash
devices based on firmware files using the format described by the PLDM
for Firmware Update standard.
This library consists of logic to parse the PLDM file format from
a firmware file object, as well as common logic for sending the relevant
PLDM header data to the device firmware.
A simple ops table is provided so that device drivers can implement
device specific hardware interactions while keeping the common logic to
the pldmfw library.
This library will be used by the Intel ice networking driver as part of
implementing device flash update via devlink. The library aims to be
vendor and device agnostic. For this reason, it has been placed in
lib/pldmfw, in the hopes that other devices which use the PLDM firmware
file format may benefit from it in the future. However, do note that not
all features defined in the PLDM standard have been implemented.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull documentation updates from Jonathan Corbet:
"A fair amount of stuff this time around, dominated by yet another
massive set from Mauro toward the completion of the RST conversion. I
*really* hope we are getting close to the end of this. Meanwhile,
those patches reach pretty far afield to update document references
around the tree; there should be no actual code changes there. There
will be, alas, more of the usual trivial merge conflicts.
Beyond that we have more translations, improvements to the sphinx
scripting, a number of additions to the sysctl documentation, and lots
of fixes"
* tag 'docs-5.8' of git://git.lwn.net/linux: (130 commits)
Documentation: fixes to the maintainer-entry-profile template
zswap: docs/vm: Fix typo accept_threshold_percent in zswap.rst
tracing: Fix events.rst section numbering
docs: acpi: fix old http link and improve document format
docs: filesystems: add info about efivars content
Documentation: LSM: Correct the basic LSM description
mailmap: change email for Ricardo Ribalda
docs: sysctl/kernel: document unaligned controls
Documentation: admin-guide: update bug-hunting.rst
docs: sysctl/kernel: document ngroups_max
nvdimm: fixes to maintainter-entry-profile
Documentation/features: Correct RISC-V kprobes support entry
Documentation/features: Refresh the arch support status files
Revert "docs: sysctl/kernel: document ngroups_max"
docs: move locking-specific documents to locking/
docs: move digsig docs to the security book
docs: move the kref doc into the core-api book
docs: add IRQ documentation at the core-api book
docs: debugging-via-ohci1394.txt: add it to the core-api book
docs: fix references for ipmi.rst file
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"A sizeable pile of arm64 updates for 5.8.
Summary below, but the big two features are support for Branch Target
Identification and Clang's Shadow Call stack. The latter is currently
arm64-only, but the high-level parts are all in core code so it could
easily be adopted by other architectures pending toolchain support
Branch Target Identification (BTI):
- Support for ARMv8.5-BTI in both user- and kernel-space. This allows
branch targets to limit the types of branch from which they can be
called and additionally prevents branching to arbitrary code,
although kernel support requires a very recent toolchain.
- Function annotation via SYM_FUNC_START() so that assembly functions
are wrapped with the relevant "landing pad" instructions.
- BPF and vDSO updates to use the new instructions.
- Addition of a new HWCAP and exposure of BTI capability to userspace
via ID register emulation, along with ELF loader support for the
BTI feature in .note.gnu.property.
- Non-critical fixes to CFI unwind annotations in the sigreturn
trampoline.
Shadow Call Stack (SCS):
- Support for Clang's Shadow Call Stack feature, which reserves
platform register x18 to point at a separate stack for each task
that holds only return addresses. This protects function return
control flow from buffer overruns on the main stack.
- Save/restore of x18 across problematic boundaries (user-mode,
hypervisor, EFI, suspend, etc).
- Core support for SCS, should other architectures want to use it
too.
- SCS overflow checking on context-switch as part of the existing
stack limit check if CONFIG_SCHED_STACK_END_CHECK=y.
CPU feature detection:
- Removed numerous "SANITY CHECK" errors when running on a system
with mismatched AArch32 support at EL1. This is primarily a concern
for KVM, which disabled support for 32-bit guests on such a system.
- Addition of new ID registers and fields as the architecture has
been extended.
Perf and PMU drivers:
- Minor fixes and cleanups to system PMU drivers.
Hardware errata:
- Unify KVM workarounds for VHE and nVHE configurations.
- Sort vendor errata entries in Kconfig.
Secure Monitor Call Calling Convention (SMCCC):
- Update to the latest specification from Arm (v1.2).
- Allow PSCI code to query the SMCCC version.
Software Delegated Exception Interface (SDEI):
- Unexport a bunch of unused symbols.
- Minor fixes to handling of firmware data.
Pointer authentication:
- Add support for dumping the kernel PAC mask in vmcoreinfo so that
the stack can be unwound by tools such as kdump.
- Simplification of key initialisation during CPU bringup.
BPF backend:
- Improve immediate generation for logical and add/sub instructions.
vDSO:
- Minor fixes to the linker flags for consistency with other
architectures and support for LLVM's unwinder.
- Clean up logic to initialise and map the vDSO into userspace.
ACPI:
- Work around for an ambiguity in the IORT specification relating to
the "num_ids" field.
- Support _DMA method for all named components rather than only PCIe
root complexes.
- Minor other IORT-related fixes.
Miscellaneous:
- Initialise debug traps early for KGDB and fix KDB cacheflushing
deadlock.
- Minor tweaks to early boot state (documentation update, set
TEXT_OFFSET to 0x0, increase alignment of PE/COFF sections).
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (148 commits)
KVM: arm64: Move __load_guest_stage2 to kvm_mmu.h
KVM: arm64: Check advertised Stage-2 page size capability
arm64/cpufeature: Add get_arm64_ftr_reg_nowarn()
ACPI/IORT: Remove the unused __get_pci_rid()
arm64/cpuinfo: Add ID_MMFR4_EL1 into the cpuinfo_arm64 context
arm64/cpufeature: Add remaining feature bits in ID_AA64PFR1 register
arm64/cpufeature: Add remaining feature bits in ID_AA64PFR0 register
arm64/cpufeature: Add remaining feature bits in ID_AA64ISAR0 register
arm64/cpufeature: Add remaining feature bits in ID_MMFR4 register
arm64/cpufeature: Add remaining feature bits in ID_PFR0 register
arm64/cpufeature: Introduce ID_MMFR5 CPU register
arm64/cpufeature: Introduce ID_DFR1 CPU register
arm64/cpufeature: Introduce ID_PFR2 CPU register
arm64/cpufeature: Make doublelock a signed feature in ID_AA64DFR0
arm64/cpufeature: Drop TraceFilt feature exposure from ID_DFR0 register
arm64/cpufeature: Add explicit ftr_id_isar0[] for ID_ISAR0 register
arm64: mm: Add asid_gen_match() helper
firmware: smccc: Fix missing prototype warning for arm_smccc_version_init
arm64: vdso: Fix CFI directives in sigreturn trampoline
arm64: vdso: Don't prefix sigreturn trampoline with a BTI C instruction
...
|
|
Many devices have control registers which control some measurable
property. Often a register contains control field so that change in
this field causes linear change in the controlled property. It is not
a rare case that user wants to give 'meaningful' control values and
driver needs to convert them to register field values. Even more
often user wants to 'see' the currently set value - again in
meaningful units - and driver needs to convert the values it reads
from register to these meaningful units. Examples of this include:
- regulators, voltage/current configurations
- power, voltage/current configurations
- clk(?) NCOs
and maybe others I can't think of right now.
Provide a linear_range helper which can do conversion from user value
to register value 'selector'.
The idea here is stolen from regulator framework and patches refactoring
the regulator helpers to use this are following.
Current implementation does not support inversely proportional ranges
but it might be useful if we could support also inversely proportional
ranges?
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/59259bc475e0c800eb4bb163f02528c7c01f7b3a.1588944082.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This file is close enough to being in rst format that I didn't feel
the need to alter it in any way.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Michel Lespinasse <walken@google.com>
Link: https://lore.kernel.org/r/20200401173343.17472-1-willy@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
As x86 was converted to use the modern SYM_ annotations for assembly,
ifdefs were added to remove the generic definitions of the old style
annotations on x86. Rather than collect a list of architectures in the
ifdefs as more architectures are converted over, provide a Kconfig
symbol for this and update x86 to use it.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lkml.kernel.org/r/20200416182402.6206-1-broonie@kernel.org
|
