| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Following the recent update to MAINTAINERS update my e-mail address.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the DEC FDDIcontroller 700 (DEFZA), Digital Equipment
Corporation's first-generation FDDI network interface adapter, made for
TURBOchannel and based on a discrete version of what eventually became
Motorola's widely used CAMEL chipset.
The CAMEL chipset is present for example in the DEC FDDIcontroller
TURBOchannel, EISA and PCI adapters (DEFTA/DEFEA/DEFPA) that we support
with the `defxx' driver, however the host bus interface logic and the
firmware API are different in the DEFZA and hence a separate driver is
required.
There isn't much to say about the driver except that it works, but there
is one peculiarity to mention. The adapter implements two Tx/Rx queue
pairs.
Of these one pair is the usual network Tx/Rx queue pair, in this case
used by the adapter to exchange frames with the ring, via the RMC (Ring
Memory Controller) chip. The Tx queue is handled directly by the RMC
chip and resides in onboard packet memory. The Rx queue is maintained
via DMA in host memory by adapter's firmware copying received data
stored by the RMC in onboard packet memory.
The other pair is used to communicate SMT frames with adapter's
firmware. Any SMT frame received from the RMC via the Rx queue must be
queued back by the driver to the SMT Rx queue for the firmware to
process. Similarly the firmware uses the SMT Tx queue to supply the
driver with SMT frames that must be queued back to the Tx queue for the
RMC to send to the ring.
This solution was chosen because the designers ran out of PCB space and
could not squeeze in more logic onto the board that would be required to
handle this SMT frame traffic without the need to involve the driver, as
with the later DEFTA/DEFEA/DEFPA adapters.
Finally the driver does some Frame Control byte decoding, so to avoid
magic numbers some macros are added to <linux/if_fddi.h>.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some of our FDDI support code has been apparently written with an
assumption that tabs are 4-character wide. In preparation to the next
change this update reformats <linux/if_fddi.h> so that it stays within 79
columns and otherwise renders correctly with 8-character tabs. No
functional change.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
|
