| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Unlike IPv4, in IPv6 there is no unique structure to represent the
nexthop and both the route and nexthop information are squashed to the
same structure ('struct fib6_info'). In order to improve resource
utilization the driver consolidates identical nexthop groups to the same
internal representation of a nexthop group.
Therefore, when the offload indication of a nexthop changes, the driver
needs to iterate over all the linked fib6_info and toggle their offload
flag accordingly.
During abort, all the routes are removed from the device and unlinked
from their nexthop group. The offload indication is cleared just before
the group is destroyed, but by that time no fib6_info is linked to the
group and the offload indication remains set.
Fix this by clearing the offload indication just before dropping the
reference from the nexthop.
Fixes: ee5a0448e72b ("mlxsw: spectrum_router: Set hardware flags for routes")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver uses the same table to represent both the main and local
routing tables. Prevent routes in the main table from replacing routes
in the local table to reflect the fact that the local table is consulted
first during lookup.
Fixes: b6a1d871d37a ("mlxsw: spectrum_router: Start using new IPv4 route notifications")
Fixes: dacad7b34b59 ("mlxsw: spectrum_router: Start using new IPv6 route notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This matches /sys/devices/.../spi1.0/modalias content.
Fixes: 9b2d9f05cddf ("net: dsa: microchip: add ksz9567 to ksz9477 driver")
Fixes: d9033ae95cf4 ("net: dsa: microchip: add KSZ8563 compatibility string")
Fixes: 8c29bebb1f8a ("net: dsa: microchip: add KSZ9893 switch support")
Fixes: 45316818371d ("net: dsa: add support for ksz9897 ethernet switch")
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop removing modes that are not supported on the system interface
when the connected PHY is capable of rate adaptation. This addresses
an issue with the LS1046ARDB board 10G interface no longer working
with an 1G link partner after autonegotiation support was added
for the Aquantia PHY on board in
commit 09c4c57f7bc4 ("net: phy: aquantia: add support for auto-negotiation configuration")
Before this commit the values advertised by the PHY were not
influenced by the dpaa_eth driver removal of system-side unsupported
modes as the aqr_config_aneg() was basically a no-op. After this
commit, the modes removed by the dpaa_eth driver were no longer
advertised thus autonegotiation with 1G link partners failed.
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent patch to support passive mode converter did not take care the
phy interface configuration in PCI platform data. Hence, converting all
the PCI platform data from plat->interface to plat->phy_interface as the
default mode is meant for PHY.
Fixes: 0060c8783330 ("net: stmmac: implement support for passive mode converters via dt")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 0efedbf11f07a ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Verma, Aashish <aashishx.verma@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should always do a read of current value of XGMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: 3cd1cfcba26e2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It should always do a read of current value of GMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: c1be0022df0d ("net: stmmac: Add VLAN HASH filtering support in GMAC4+")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The caller of XDP_SETUP_PROG has already incremented refcnt in
__bpf_prog_get(), so drivers should only increment refcnt by
num_queues - 1.
To fix the issue, update netvsc_xdp_set() to add the correct number
to refcnt.
Hold a refcnt in netvsc_xdp_set()’s other caller, netvsc_attach().
And, do the same in netvsc_vf_setxdp(). Otherwise, every time when VF is
removed and added from the host side, the refcnt will be decreased by one,
which may cause page fault when unloading xdp program.
Fixes: 351e1581395f ("hv_netvsc: Add XDP support")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8d0 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering")
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It forgot to reduce the value of the variable retry in a while loop
in the ethqos_configure() function. It may cause an endless loop and
without timeout.
Fixes: a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* pm-avs:
power: avs: qcom-cpr: Avoid clang -Wsometimes-uninitialized in cpr_scale
power: avs: qcom-cpr: add unspecified HAS_IOMEM dependency
PM / AVS: rockchip-io: fix the supply naming for the emmc supply on px30
power: avs: qcom-cpr: add a printout after the driver has been initialized
* pm-cpuidle:
cpuidle: Documentation: Clean up PM QoS description
intel_idle: Introduce 'states_off' module parameter
intel_idle: Introduce 'use_acpi' module parameter
|
|
As it is, vfs_parse_fs_string() makes "foo" and "foo=" indistinguishable;
both get fs_value_is_string for ->type and NULL for ->string. To make
it even more unpleasant, that combination is impossible to produce with
fsconfig().
Much saner rules would be
"foo" => fs_value_is_flag, NULL
"foo=" => fs_value_is_string, ""
"foo=bar" => fs_value_is_string, "bar"
All cases are distinguishable, all results are expressable by fsconfig(),
->has_value checks are much simpler that way (to the point of the field
being useless) and quite a few regressions go away (gfs2 has no business
accepting -o nodebug=, for example).
Partially based upon patches from Miklos.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-next
amd-drm-next-5.6-2020-02-05:
amdgpu:
- EDC fixes for Arcturus
- GDDR6 memory training fixe
- Fix for reading gfx clockgating registers while in GFXOFF state
- i2c freq fixes
- Misc display fixes
- TLB invalidation fix when using semaphores
- VCN 2.5 instancing fixes
- Switch raven1 gfxoff to a blacklist
- Coreboot workaround for KV/KB
- Root cause dongle fixes for display and revert workaround
- Enable GPU reset for renoir and navi
- Navi overclocking fixes
- Fix up confusing warnings in display clock validation on raven
amdkfd:
- SDMA fix
radeon:
- Misc LUT fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206035458.3894-1-alexander.deucher@amd.com
|
|
Just a couple of fixes to Volta/Turing modesetting on some systems.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CACAvsv7=eP+Ai1ouoMyYyo1xMF0pTQki=owYjJkS=NpvKQd1fg@mail.gmail.com
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v5.6-rc1
These are a couple of quick fixes for regressions that were found during
the first two weeks of the merge window.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206172753.2185390-1-thierry.reding@gmail.com
|
|
Deprecate the generic TLS cap bit, use the new TX-specific
TLS cap bit instead.
Fixes: a12ff35e0fb7 ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For a cyclic work queue, when not requesting a completion per WQE,
a single CQE might indicate the completion of several WQEs.
However, in case some WQE in the batch causes an error, then an error
completion is issued, breaking the batch, and pointing to the offending
WQE in the wqe_counter field.
Hence, WQE-specific error CQE handling (like printing, breaking, etc...)
should be performed only for the last WQE in batch.
Fixes: 130c7b46c93d ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Fixes: fd9b4be8002c ("net/mlx5e: RX, Support multiple outstanding UMR posts")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
SA context is allocated at mlx5_fpga_ipsec_create_sa_ctx,
however the counterpart mlx5_fpga_ipsec_delete_sa_ctx function
nullifies sa_ctx pointer without freeing the memory allocated,
hence the memory leak.
Fix by free SA context when the SA is released.
Fixes: d6c4f0298cec ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The function mlx5_fpga_esp_validate_xfrm_attrs is wrongly used
with negative negation as zero value indicates success but it
used as failure return value instead.
Fix by remove the unary not negation operator.
Fixes: 05564d0ae075 ("net/mlx5: Add flow-steering commands for FPGA IPSec implementation")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
free_match_list could be called when the flow table is already
locked. We need to pass this notation to tree_put_node.
It fixes the following lockdep warnning:
[ 1797.268537] ============================================
[ 1797.276837] WARNING: possible recursive locking detected
[ 1797.285101] 5.5.0-rc5+ #10 Not tainted
[ 1797.291641] --------------------------------------------
[ 1797.299917] handler10/9296 is trying to acquire lock:
[ 1797.307885] ffff889ad399a0a0 (&node->lock){++++}, at:
tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.319694]
[ 1797.319694] but task is already holding lock:
[ 1797.330904] ffff889ad399a0a0 (&node->lock){++++}, at:
nested_down_write_ref_node.part.33+0x1a/0x60 [mlx5_core]
[ 1797.344707]
[ 1797.344707] other info that might help us debug this:
[ 1797.356952] Possible unsafe locking scenario:
[ 1797.356952]
[ 1797.368333] CPU0
[ 1797.373357] ----
[ 1797.378364] lock(&node->lock);
[ 1797.384222] lock(&node->lock);
[ 1797.390031]
[ 1797.390031] *** DEADLOCK ***
[ 1797.390031]
[ 1797.403003] May be due to missing lock nesting notation
[ 1797.403003]
[ 1797.414691] 3 locks held by handler10/9296:
[ 1797.421465] #0: ffff889cf2c5a110 (&block->cb_lock){++++}, at:
tc_setup_cb_add+0x70/0x250
[ 1797.432810] #1: ffff88a030081490 (&comp->sem){++++}, at:
mlx5_devcom_get_peer_data+0x4c/0xb0 [mlx5_core]
[ 1797.445829] #2: ffff889ad399a0a0 (&node->lock){++++}, at:
nested_down_write_ref_node.part.33+0x1a/0x60 [mlx5_core]
[ 1797.459913]
[ 1797.459913] stack backtrace:
[ 1797.469436] CPU: 1 PID: 9296 Comm: handler10 Kdump: loaded Not
tainted 5.5.0-rc5+ #10
[ 1797.480643] Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS
2.4.3 01/17/2017
[ 1797.491480] Call Trace:
[ 1797.496701] dump_stack+0x96/0xe0
[ 1797.502864] __lock_acquire.cold.63+0xf8/0x212
[ 1797.510301] ? lockdep_hardirqs_on+0x250/0x250
[ 1797.517701] ? mark_held_locks+0x55/0xa0
[ 1797.524547] ? quarantine_put+0xb7/0x160
[ 1797.531422] ? lockdep_hardirqs_on+0x17d/0x250
[ 1797.538913] lock_acquire+0xd6/0x1f0
[ 1797.545529] ? tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.553701] down_write+0x94/0x140
[ 1797.560206] ? tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.568464] ? down_write_killable_nested+0x170/0x170
[ 1797.576925] ? del_hw_flow_group+0xde/0x1f0 [mlx5_core]
[ 1797.585629] tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.593891] ? free_match_list.part.25+0x147/0x170 [mlx5_core]
[ 1797.603389] free_match_list.part.25+0xe0/0x170 [mlx5_core]
[ 1797.612654] _mlx5_add_flow_rules+0x17e2/0x20b0 [mlx5_core]
[ 1797.621838] ? lock_acquire+0xd6/0x1f0
[ 1797.629028] ? esw_get_prio_table+0xb0/0x3e0 [mlx5_core]
[ 1797.637981] ? alloc_insert_flow_group+0x420/0x420 [mlx5_core]
[ 1797.647459] ? try_to_wake_up+0x4c7/0xc70
[ 1797.654881] ? lock_downgrade+0x350/0x350
[ 1797.662271] ? __mutex_unlock_slowpath+0xb1/0x3f0
[ 1797.670396] ? find_held_lock+0xac/0xd0
[ 1797.677540] ? mlx5_add_flow_rules+0xdc/0x360 [mlx5_core]
[ 1797.686467] mlx5_add_flow_rules+0xdc/0x360 [mlx5_core]
[ 1797.695134] ? _mlx5_add_flow_rules+0x20b0/0x20b0 [mlx5_core]
[ 1797.704270] ? irq_exit+0xa5/0x170
[ 1797.710764] ? retint_kernel+0x10/0x10
[ 1797.717698] ? mlx5_eswitch_set_rule_source_port.isra.9+0x122/0x230
[mlx5_core]
[ 1797.728708] mlx5_eswitch_add_offloaded_rule+0x465/0x6d0 [mlx5_core]
[ 1797.738713] ? mlx5_eswitch_get_prio_range+0x30/0x30 [mlx5_core]
[ 1797.748384] ? mlx5_fc_stats_work+0x670/0x670 [mlx5_core]
[ 1797.757400] mlx5e_tc_offload_fdb_rules.isra.27+0x24/0x90 [mlx5_core]
[ 1797.767665] mlx5e_tc_add_fdb_flow+0xaf8/0xd40 [mlx5_core]
[ 1797.776886] ? mlx5e_encap_put+0xd0/0xd0 [mlx5_core]
[ 1797.785562] ? mlx5e_alloc_flow.isra.43+0x18c/0x1c0 [mlx5_core]
[ 1797.795353] __mlx5e_add_fdb_flow+0x2e2/0x440 [mlx5_core]
[ 1797.804558] ? mlx5e_tc_update_neigh_used_value+0x8c0/0x8c0
[mlx5_core]
[ 1797.815093] ? wait_for_completion+0x260/0x260
[ 1797.823272] mlx5e_configure_flower+0xe94/0x1620 [mlx5_core]
[ 1797.832792] ? __mlx5e_add_fdb_flow+0x440/0x440 [mlx5_core]
[ 1797.842096] ? down_read+0x11a/0x2e0
[ 1797.849090] ? down_write+0x140/0x140
[ 1797.856142] ? mlx5e_rep_indr_setup_block_cb+0xc0/0xc0 [mlx5_core]
[ 1797.866027] tc_setup_cb_add+0x11a/0x250
[ 1797.873339] fl_hw_replace_filter+0x25e/0x320 [cls_flower]
[ 1797.882385] ? fl_hw_destroy_filter+0x1c0/0x1c0 [cls_flower]
[ 1797.891607] fl_change+0x1d54/0x1fb6 [cls_flower]
[ 1797.899772] ? __rhashtable_insert_fast.constprop.50+0x9f0/0x9f0
[cls_flower]
[ 1797.910728] ? lock_downgrade+0x350/0x350
[ 1797.918187] ? __radix_tree_lookup+0xa5/0x130
[ 1797.926046] ? fl_set_key+0x1590/0x1590 [cls_flower]
[ 1797.934611] ? __rhashtable_insert_fast.constprop.50+0x9f0/0x9f0
[cls_flower]
[ 1797.945673] tc_new_tfilter+0xcd1/0x1240
[ 1797.953138] ? tc_del_tfilter+0xb10/0xb10
[ 1797.960688] ? avc_has_perm_noaudit+0x92/0x320
[ 1797.968721] ? avc_has_perm_noaudit+0x1df/0x320
[ 1797.976816] ? avc_has_extended_perms+0x990/0x990
[ 1797.985090] ? mark_lock+0xaa/0x9e0
[ 1797.991988] ? match_held_lock+0x1b/0x240
[ 1797.999457] ? match_held_lock+0x1b/0x240
[ 1798.006859] ? find_held_lock+0xac/0xd0
[ 1798.014045] ? symbol_put_addr+0x40/0x40
[ 1798.021317] ? rcu_read_lock_sched_held+0xd0/0xd0
[ 1798.029460] ? tc_del_tfilter+0xb10/0xb10
[ 1798.036810] rtnetlink_rcv_msg+0x4d5/0x620
[ 1798.044236] ? rtnl_bridge_getlink+0x460/0x460
[ 1798.052034] ? lockdep_hardirqs_on+0x250/0x250
[ 1798.059837] ? match_held_lock+0x1b/0x240
[ 1798.067146] ? find_held_lock+0xac/0xd0
[ 1798.074246] netlink_rcv_skb+0xc6/0x1f0
[ 1798.081339] ? rtnl_bridge_getlink+0x460/0x460
[ 1798.089104] ? netlink_ack+0x440/0x440
[ 1798.096061] netlink_unicast+0x2d4/0x3b0
[ 1798.103189] ? netlink_attachskb+0x3f0/0x3f0
[ 1798.110724] ? _copy_from_iter_full+0xda/0x370
[ 1798.118415] netlink_sendmsg+0x3ba/0x6a0
[ 1798.125478] ? netlink_unicast+0x3b0/0x3b0
[ 1798.132705] ? netlink_unicast+0x3b0/0x3b0
[ 1798.139880] sock_sendmsg+0x94/0xa0
[ 1798.146332] ____sys_sendmsg+0x36c/0x3f0
[ 1798.153251] ? copy_msghdr_from_user+0x165/0x230
[ 1798.160941] ? kernel_sendmsg+0x30/0x30
[ 1798.167738] ___sys_sendmsg+0xeb/0x150
[ 1798.174411] ? sendmsg_copy_msghdr+0x30/0x30
[ 1798.181649] ? lock_downgrade+0x350/0x350
[ 1798.188559] ? rcu_read_lock_sched_held+0xd0/0xd0
[ 1798.196239] ? __fget+0x21d/0x320
[ 1798.202335] ? do_dup2+0x2a0/0x2a0
[ 1798.208499] ? lock_downgrade+0x350/0x350
[ 1798.215366] ? __fget_light+0xd6/0xf0
[ 1798.221808] ? syscall_trace_enter+0x369/0x5d0
[ 1798.229112] __sys_sendmsg+0xd3/0x160
[ 1798.235511] ? __sys_sendmsg_sock+0x60/0x60
[ 1798.242478] ? syscall_trace_enter+0x233/0x5d0
[ 1798.249721] ? syscall_slow_exit_work+0x280/0x280
[ 1798.257211] ? do_syscall_64+0x1e/0x2e0
[ 1798.263680] do_syscall_64+0x72/0x2e0
[ 1798.269950] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The DMA direction is only used by the DMA API, so there is no use in
setting it when a buffer object isn't mapped with the DMA API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
|
|
This partially reverts the DMA API support that was recently merged
because it was causing performance regressions on older Tegra devices.
Unfortunately, the cache maintenance performed by dma_map_sg() and
dma_unmap_sg() causes performance to drop by a factor of 10.
The right solution for this would be to cache mappings for buffers per
consumer device, but that's a bit involved. Instead, we simply revert to
the old behaviour of sharing IOVA mappings when we know that devices can
do so (i.e. they share the same IOMMU domain).
Cc: <stable@vger.kernel.org> # v5.5
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Older Tegra devices only allow addressing 32 bits of memory, so whether
or not the host1x is attached to an IOMMU doesn't matter. host1x IOMMU
attachment is only needed on devices that can address memory beyond the
32-bit boundary and where the host1x doesn't support the wide GATHER
opcode that allows it to access buffers at higher addresses.
Cc: <stable@vger.kernel.org> # v5.5
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Define to_pci_sysdata() always to fix build breakage when !CONFIG_PCI
(Jason A. Donenfeld)
- Use PF PASID for VFs to fix VF IOMMU bind failures (Kuppuswamy
Sathyanarayanan)
* tag 'pci-v5.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/ATS: Use PF PASID for VFs
x86/PCI: Define to_pci_sysdata() even when !CONFIG_PCI
|
|
After a number of suspend and resume cycles, it is possible for the RBUF
to be stuck in Wake-on-LAN mode, despite the MPD enable bit being
cleared which instructed the RBUF to exit that mode.
Avoid creating that problematic condition by clearing the RX_EN and
TX_EN bits in the UniMAC prior to disable the Magic Packet Detector
logic which is guaranteed to make the RBUF exit Wake-on-LAN mode.
Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d365498 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ceph fixes from Ilya Dryomov:
- a set of patches that fixes various corner cases in mount and umount
code (Xiubo Li). This has to do with choosing an MDS, distinguishing
between laggy and down MDSes and parsing the server path.
- inode initialization fixes (Jeff Layton). The one included here
mostly concerns things like open_by_handle() and there is another one
that will come through Al.
- copy_file_range() now uses the new copy-from2 op (Luis Henriques).
The existing copy-from op turned out to be infeasible for generic
filesystem use; we disable the copy offload if OSDs don't support
copy-from2.
- a patch to link "rbd" and "block" devices together in sysfs (Hannes
Reinecke)
... and a smattering of cleanups from Xiubo, Jeff and Chengguang.
* tag 'ceph-for-5.6-rc1' of https://github.com/ceph/ceph-client: (25 commits)
rbd: set the 'device' link in sysfs
ceph: move net/ceph/ceph_fs.c to fs/ceph/util.c
ceph: print name of xattr in __ceph_{get,set}xattr() douts
ceph: print r_direct_hash in hex in __choose_mds() dout
ceph: use copy-from2 op in copy_file_range
ceph: close holes in structs ceph_mds_session and ceph_mds_request
rbd: work around -Wuninitialized warning
ceph: allocate the correct amount of extra bytes for the session features
ceph: rename get_session and switch to use ceph_get_mds_session
ceph: remove the extra slashes in the server path
ceph: add possible_max_rank and make the code more readable
ceph: print dentry offset in hex and fix xattr_version type
ceph: only touch the caps which have the subset mask requested
ceph: don't clear I_NEW until inode metadata is fully populated
ceph: retry the same mds later after the new session is opened
ceph: check availability of mds cluster on mount after wait timeout
ceph: keep the session state until it is released
ceph: add __send_request helper
ceph: ensure we have a new cap before continuing in fill_inode
ceph: drop unused ttl_from parameter from fill_inode
...
|
|
Move rx_dropped and rx_errors counters in mvneta_pcpu_stats in order to
avoid possible races updating statistics
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM")
Fixes: dc35a10f68d3 ("net: mvneta: bm: add support for hardware buffer management")
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added debugfs entry to show the tls stats.
Signed-off-by: Devulapally Shiva Krishna <shiva@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We forget to put the inode and unmount the kernfs used for compaction.
Fixes: 71994620bb25 ("virtio_balloon: replace oom notifier with shrinker")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: Liang Li <liang.z.li@intel.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200205163402.42627-3-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When unloading the driver while hinting is in progress, we will not
release the free page blocks back to MM, resulting in a memory leak.
Fixes: 86a559787e6f ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: Liang Li <liang.z.li@intel.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200205163402.42627-2-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Make sure, at build time, that pfn array is big enough to hold a single
page. It happens to be true since the PAGE_SHIFT value at the moment is
20, which is 1M - exactly 256 4K balloon pages.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
|
|
Since the need for a special flag to support SCSI passthrough on a
block device was added in May 2017 the SCSI passthrough support in
virtio-blk has been disabled. It has always been a bad idea
(just ask the original author..) and we have virtio-scsi for proper
passthrough. The feature also never made it into the virtio 1.0
or later specifications.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
VQs without a name specified are not valid; they are skipped in the
later loop that assigns MSI-X vectors to queues, but the per_vq_vectors
loop above that counts the required number of vectors previously still
counted any queue with a non-NULL callback as needing a vector.
Add a check to the per_vq_vectors loop so that vectors with no name are
not counted to make the two loops consistent. This prevents
over-counting unnecessary vectors (e.g. for features which were not
negotiated with the device).
Cc: stable@vger.kernel.org
Fixes: 86a559787e6f ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Wang, Wei W <wei.w.wang@intel.com>
|
|
Ensure that elements of the callbacks array that correspond to
unavailable features are set to NULL; previously, they would be left
uninitialized.
Since the corresponding names array elements were explicitly set to
NULL, the uninitialized callback pointers would not actually be
dereferenced; however, the uninitialized callbacks elements would still
be read in vp_find_vqs_msix() and used to calculate the number of MSI-X
vectors required.
Cc: stable@vger.kernel.org
Fixes: 86a559787e6f ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Use devm_platform_ioremap_resource() to simplify code, which
contains platform_get_resource, devm_request_mem_region and
devm_ioremap.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Added new "bootconfig".
This looks for a file appended to initrd to add boot config options,
and has been discussed thoroughly at Linux Plumbers.
Very useful for adding kprobes at bootup.
Only enabled if "bootconfig" is on the real kernel command line.
- Created dynamic event creation.
Merges common code between creating synthetic events and kprobe
events.
- Rename perf "ring_buffer" structure to "perf_buffer"
- Rename ftrace "ring_buffer" structure to "trace_buffer"
Had to rename existing "trace_buffer" to "array_buffer"
- Allow trace_printk() to work withing (some) tracing code.
- Sort of tracing configs to be a little better organized
- Fixed bug where ftrace_graph hash was not being protected properly
- Various other small fixes and clean ups
* tag 'trace-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (88 commits)
bootconfig: Show the number of nodes on boot message
tools/bootconfig: Show the number of bootconfig nodes
bootconfig: Add more parse error messages
bootconfig: Use bootconfig instead of boot config
ftrace: Protect ftrace_graph_hash with ftrace_sync
ftrace: Add comment to why rcu_dereference_sched() is open coded
tracing: Annotate ftrace_graph_notrace_hash pointer with __rcu
tracing: Annotate ftrace_graph_hash pointer with __rcu
bootconfig: Only load bootconfig if "bootconfig" is on the kernel cmdline
tracing: Use seq_buf for building dynevent_cmd string
tracing: Remove useless code in dynevent_arg_pair_add()
tracing: Remove check_arg() callbacks from dynevent args
tracing: Consolidate some synth_event_trace code
tracing: Fix now invalid var_ref_vals assumption in trace action
tracing: Change trace_boot to use synth_event interface
tracing: Move tracing selftests to bottom of menu
tracing: Move mmio tracer config up with the other tracers
tracing: Move tracing test module configs together
tracing: Move all function tracing configs together
tracing: Documentation for in-kernel synthetic event API
...
|
|
Pull more block updates from Jens Axboe:
"Some later arrivals, but all fixes at this point:
- bcache fix series (Coly)
- Series of BFQ fixes (Paolo)
- NVMe pull request from Keith with a few minor NVMe fixes
- Various little tweaks"
* tag 'block-5.6-2020-02-05' of git://git.kernel.dk/linux-block: (23 commits)
nvmet: update AEN list and array at one place
nvmet: Fix controller use after free
nvmet: Fix error print message at nvmet_install_queue function
brd: check and limit max_part par
nvme-pci: remove nvmeq->tags
nvmet: fix dsm failure when payload does not match sgl descriptor
nvmet: Pass lockdep expression to RCU lists
block, bfq: clarify the goal of bfq_split_bfqq()
block, bfq: get a ref to a group when adding it to a service tree
block, bfq: remove ifdefs from around gets/puts of bfq groups
block, bfq: extend incomplete name of field on_st
block, bfq: get extra ref to prevent a queue from being freed during a group move
block, bfq: do not insert oom queue into position tree
block, bfq: do not plug I/O for bfq_queues with no proc refs
bcache: check return value of prio_read()
bcache: fix incorrect data type usage in btree_flush_write()
bcache: add readahead cache policy options via sysfs interface
bcache: explicity type cast in bset_bkey_last()
bcache: fix memory corruption in bch_cache_accounting_clear()
xen/blkfront: limit allocated memory size to actual use case
...
|
|
Pull libata updates from Jens Axboe:
- Add a Sandisk CF card to supported pata_pcmcia list (Christian)
- Move pata_arasan_cf away from legacy API (Peter)
- Ensure ahci DMA/ints are shut down on shutdown (Prabhakar)
* tag 'libata-5.6-2020-02-05' of git://git.kernel.dk/linux-block:
ata: pata_arasan_cf: Use dma_request_chan() instead dma_request_slave_channel()
ata: ahci: Add shutdown to freeze hardware resources of ahci
pata_pcmia: add SanDisk High (>8G) CF card to supported list
|
|
Return -EAGAIN instead of -ENETDOWN to provide a slightly milder
information to user space so that an application will know to retry the
syscall when __I40E_CONFIG_BUSY bit is set on pf->state.
Fixes: b3873a5be757 ("net/i40e: Fix concurrency issues between config flow and XSK")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20200205045834.56795-2-maciej.fijalkowski@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Mostly cleanups and minor improvements with some new chip support for
some drivers"
* tag 'pwm/for-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: Remove set but not set variable 'pwm'
pwm: sun4i: Initialize variables before use
pwm: stm32: Remove automatic output enable
pwm: sun4i: Narrow scope of local variable
pwm: bcm2835: Allow building for ARCH_BRCMSTB
pwm: imx27: Eliminate error message for defer probe
pwm: sun4i: Fix inconsistent IS_ERR and PTR_ERR
pwm: sun4i: Move pwm_calculate() out of spin_lock()
pwm: omap-dmtimer: Allow compiling with COMPILE_TEST
pwm: omap-dmtimer: put_device() after of_find_device_by_node()
pwm: omap-dmtimer: Simplify error handling
pwm: omap-dmtimer: Remove PWM chip in .remove before making it unfunctional
pwm: Implement tracing for .get_state() and .apply_state()
pwm: rcar: Document inability to set duty_cycle = 0
pwm: rcar: Drop useless call to pwm_get_state()
pwm: Fix minor Kconfig whitespace issues
pwm: atmel: Implement .get_state()
pwm: atmel: Use register accessors for channels
pwm: atmel: Document known weaknesses of both hardware and software
pwm: atmel: Replace loop in prescale calculation by ad-hoc calculation
...
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Fixes for:
- Documentation build error fix
- Fix dma_request_chan() error return
- Remove unneeded conversion in idxd driver
- Fix pointer check for dma_async_device_channel_register()
- Fix slave-channel symlink cleanup"
* tag 'dmaengine-fix-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: Cleanups for the slave <-> channel symlink support
dmaengine: fix null ptr check for __dma_async_device_channel_register()
dmaengine: idxd: fix boolconv.cocci warnings
dmaengine: Fix return value for dma_request_chan() in case of failure
dmaengine: doc: Properly indent metadata title
|
|
Per PCIe r5.0, sec 9.3.7.14, if a PF implements the PASID Capability, the
PF PASID configuration is shared by its VFs, and VFs must not implement
their own PASID Capability. But commit 751035b8dc06 ("PCI/ATS: Cache PASID
Capability offset") changed pci_max_pasids() and pci_pasid_features() to
use the PASID Capability of the VF device instead of the associated PF
device. This leads to IOMMU bind failures when pci_max_pasids() and
pci_pasid_features() are called for VFs.
In pci_max_pasids() and pci_pasid_features(), always use the PF PASID
Capability.
Fixes: 751035b8dc06 ("PCI/ATS: Cache PASID Capability offset")
Link: https://lore.kernel.org/r/fe891f9755cb18349389609e7fed9940fc5b081a.1580325170.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v5.5+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Allow compiling the ARM-SMMU drivers as modules.
- Fixes and cleanups for the ARM-SMMU drivers and io-pgtable code
collected by Will Deacon. The merge-commit (6855d1ba7537) has all the
details.
- Cleanup of the iommu_put_resv_regions() call-backs in various
drivers.
- AMD IOMMU driver cleanups.
- Update for the x2APIC support in the AMD IOMMU driver.
- Preparation patches for Intel VT-d nested mode support.
- RMRR and identity domain handling fixes for the Intel VT-d driver.
- More small fixes and cleanups.
* tag 'iommu-updates-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (87 commits)
iommu/amd: Remove the unnecessary assignment
iommu/vt-d: Remove unnecessary WARN_ON_ONCE()
iommu/vt-d: Unnecessary to handle default identity domain
iommu/vt-d: Allow devices with RMRRs to use identity domain
iommu/vt-d: Add RMRR base and end addresses sanity check
iommu/vt-d: Mark firmware tainted if RMRR fails sanity check
iommu/amd: Remove unused struct member
iommu/amd: Replace two consecutive readl calls with one readq
iommu/vt-d: Don't reject Host Bridge due to scope mismatch
PCI/ATS: Add PASID stubs
iommu/arm-smmu-v3: Return -EBUSY when trying to re-add a device
iommu/arm-smmu-v3: Improve add_device() error handling
iommu/arm-smmu-v3: Use WRITE_ONCE() when changing validity of an STE
iommu/arm-smmu-v3: Add second level of context descriptor table
iommu/arm-smmu-v3: Prepare for handling arm_smmu_write_ctx_desc() failure
iommu/arm-smmu-v3: Propagate ssid_bits
iommu/arm-smmu-v3: Add support for Substream IDs
iommu/arm-smmu-v3: Add context descriptor tables allocators
iommu/arm-smmu-v3: Prepare arm_smmu_s1_cfg for SSID support
ACPI/IORT: Parse SSID property of named component node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- fix a bug introduced in 5.5 in the Xen gntdev driver
- fix the Xen balloon driver when running on ancient Xen versions
- allow Xen stubdoms to control interrupt enable flags of
passed-through PCI cards
- release resources in Xen backends under memory pressure
* tag 'for-linus-5.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/blkback: Consistently insert one empty line between functions
xen/blkback: Remove unnecessary static variable name prefixes
xen/blkback: Squeeze page pools if a memory pressure is detected
xenbus/backend: Protect xenbus callback with lock
xenbus/backend: Add memory pressure handler callback
xen/gntdev: Do not use mm notifiers with autotranslating guests
xen/balloon: Support xend-based toolstack take two
xen-pciback: optionally allow interrupt enable flag writes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
"The second round of s390 fixes and features for 5.6:
- Add KPROBES_ON_FTRACE support
- Add EP11 AES secure keys support
- PAES rework and prerequisites for paes-s390 ciphers selftests
- Fix page table upgrade for hugetlbfs"
* tag 's390-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pkey/zcrypt: Support EP11 AES secure keys
s390/zcrypt: extend EP11 card and queue sysfs attributes
s390/zcrypt: add new low level ep11 functions support file
s390/zcrypt: ep11 structs rework, export zcrypt_send_ep11_cprb
s390/zcrypt: enable card/domain autoselect on ep11 cprbs
s390/crypto: enable clear key values for paes ciphers
s390/pkey: Add support for key blob with clear key value
s390/crypto: Rework on paes implementation
s390: support KPROBES_ON_FTRACE
s390/mm: fix dynamic pagetable upgrade for hugetlbfs
|
|
commit cedeac9df4b8 ("qed: Add support for Timestamping the unicast
PTP packets.") handles the timestamping of L4 ptp packets only.
This patch adds driver changes to detect/timestamp both L2/L4 unicast
PTP packets.
Fixes: cedeac9df4b8 ("qed: Add support for Timestamping the unicast PTP packets.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
