| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When working on LED support for r8169 I got the following lockdep
warning. Easiest way to prevent this scenario seems to be to take
the RTNL lock before the trigger_data lock in set_device_name().
======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc2-next-20231124+ #2 Not tainted
------------------------------------------------------
bash/383 is trying to acquire lock:
ffff888103aa1c68 (&trigger_data->lock){+.+.}-{3:3}, at: netdev_trig_notify+0xec/0x190 [ledtrig_netdev]
but task is already holding lock:
ffffffff8cddf808 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x12/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.}-{3:3}:
__mutex_lock+0x9b/0xb50
mutex_lock_nested+0x16/0x20
rtnl_lock+0x12/0x20
set_device_name+0xa9/0x120 [ledtrig_netdev]
netdev_trig_activate+0x1a1/0x230 [ledtrig_netdev]
led_trigger_set+0x172/0x2c0
led_trigger_write+0xf1/0x140
sysfs_kf_bin_write+0x5d/0x80
kernfs_fop_write_iter+0x15d/0x210
vfs_write+0x1f0/0x510
ksys_write+0x6c/0xf0
__x64_sys_write+0x14/0x20
do_syscall_64+0x3f/0xf0
entry_SYSCALL_64_after_hwframe+0x6c/0x74
-> #0 (&trigger_data->lock){+.+.}-{3:3}:
__lock_acquire+0x1459/0x25a0
lock_acquire+0xc8/0x2d0
__mutex_lock+0x9b/0xb50
mutex_lock_nested+0x16/0x20
netdev_trig_notify+0xec/0x190 [ledtrig_netdev]
call_netdevice_register_net_notifiers+0x5a/0x100
register_netdevice_notifier+0x85/0x120
netdev_trig_activate+0x1d4/0x230 [ledtrig_netdev]
led_trigger_set+0x172/0x2c0
led_trigger_write+0xf1/0x140
sysfs_kf_bin_write+0x5d/0x80
kernfs_fop_write_iter+0x15d/0x210
vfs_write+0x1f0/0x510
ksys_write+0x6c/0xf0
__x64_sys_write+0x14/0x20
do_syscall_64+0x3f/0xf0
entry_SYSCALL_64_after_hwframe+0x6c/0x74
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(rtnl_mutex);
lock(&trigger_data->lock);
lock(rtnl_mutex);
lock(&trigger_data->lock);
*** DEADLOCK ***
8 locks held by bash/383:
#0: ffff888103ff33f0 (sb_writers#3){.+.+}-{0:0}, at: ksys_write+0x6c/0xf0
#1: ffff888103aa1e88 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x114/0x210
#2: ffff8881036f1890 (kn->active#82){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x11d/0x210
#3: ffff888108e2c358 (&led_cdev->led_access){+.+.}-{3:3}, at: led_trigger_write+0x30/0x140
#4: ffffffff8cdd9e10 (triggers_list_lock){++++}-{3:3}, at: led_trigger_write+0x75/0x140
#5: ffff888108e2c270 (&led_cdev->trigger_lock){++++}-{3:3}, at: led_trigger_write+0xe3/0x140
#6: ffffffff8cdde3d0 (pernet_ops_rwsem){++++}-{3:3}, at: register_netdevice_notifier+0x1c/0x120
#7: ffffffff8cddf808 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x12/0x20
stack backtrace:
CPU: 0 PID: 383 Comm: bash Not tainted 6.7.0-rc2-next-20231124+ #2
Hardware name: Default string Default string/Default string, BIOS ADLN.M6.SODIMM.ZB.CY.015 08/08/2023
Call Trace:
<TASK>
dump_stack_lvl+0x5c/0xd0
dump_stack+0x10/0x20
print_circular_bug+0x2dd/0x410
check_noncircular+0x131/0x150
__lock_acquire+0x1459/0x25a0
lock_acquire+0xc8/0x2d0
? netdev_trig_notify+0xec/0x190 [ledtrig_netdev]
__mutex_lock+0x9b/0xb50
? netdev_trig_notify+0xec/0x190 [ledtrig_netdev]
? __this_cpu_preempt_check+0x13/0x20
? netdev_trig_notify+0xec/0x190 [ledtrig_netdev]
? __cancel_work_timer+0x11c/0x1b0
? __mutex_lock+0x123/0xb50
mutex_lock_nested+0x16/0x20
? mutex_lock_nested+0x16/0x20
netdev_trig_notify+0xec/0x190 [ledtrig_netdev]
call_netdevice_register_net_notifiers+0x5a/0x100
register_netdevice_notifier+0x85/0x120
netdev_trig_activate+0x1d4/0x230 [ledtrig_netdev]
led_trigger_set+0x172/0x2c0
? preempt_count_add+0x49/0xc0
led_trigger_write+0xf1/0x140
sysfs_kf_bin_write+0x5d/0x80
kernfs_fop_write_iter+0x15d/0x210
vfs_write+0x1f0/0x510
ksys_write+0x6c/0xf0
__x64_sys_write+0x14/0x20
do_syscall_64+0x3f/0xf0
entry_SYSCALL_64_after_hwframe+0x6c/0x74
RIP: 0033:0x7f269055d034
Code: c7 00 16 00 00 00 b8 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 80 3d 35 c3 0d 00 00 74 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 48 83 ec 28 48 89 54 24 18 48
RSP: 002b:00007ffddb7ef748 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000007 RCX: 00007f269055d034
RDX: 0000000000000007 RSI: 000055bf5f4af3c0 RDI: 0000000000000001
RBP: 000055bf5f4af3c0 R08: 0000000000000073 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000007
R13: 00007f26906325c0 R14: 00007f269062ff20 R15: 0000000000000000
</TASK>
Fixes: d5e01266e7f5 ("leds: trigger: netdev: add additional specific link speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/fb5c8294-2a10-4bf5-8f10-3d2b77d2757e@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit c7d80059b086 ("leds: class: Store the color index in struct
led_classdev") introduced a new sysfs entry "color" that is commonly
created for the led classdev. Unfortunately, this conflicts with the
"color" sysfs entry of already existing drivers such as Logitech HID
or System76 ACPI drivers. The driver probe fails due to the conflict,
hence it leads to a severe regression with the missing keyboard, for
example.
This patch reverts partially the change in the commit above for
removing the led class color sysfs entries again for addressing the
regressions. The newly introduced led_classdev.color field is kept as
it's already used by other driver.
Fixes: c7d80059b086 ("leds: class: Store the color index in struct led_classdev")
Reported-by: Johannes Penßel <johannes.penssel@gmail.com>
Closes: https://lore.kernel.org/r/b5646db3-acff-45aa-baef-df3f660486fb@gmail.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218045
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218155
Link: https://bugzilla.suse.com/show_bug.cgi?id=1217172
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231121162359.9332-1-tiwai@suse.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add support for a bunch more colours
New Drivers:
- Add support for Kinetic KTD2026/7 RGB/White LEDs
New Functionality:
- Add support for device to enter HW Controlled Mode to Turris Omnia
LEDs
- Add support for HW Gamma Correction to Turris Omnia LEDs
Fix-ups:
- Apply new __counted_by() annotation to several data structures
containing flexible arrays
- Rid the return value from Platform's .remove() operation
- Use *_cansleep() variants for instances were threads can sleep
- Improve the semantics when setting the brightness
- Generic clean-ups; code reduction, coding style, standard patterns
- Replace strncpy() with strscpy()
- Fix-up / add various documentation
- Re-author the GPIO associated Trigger to use trigger-sources
- Move to using standard APIs and helpers
- Improve error checking
- Stop using static GPIO bases
Bug Fixes:
- Fix Pointer to Enum casing warnings
- Do not pretend that I2C backed device supports SMBUS
- Ensure PWM LEDs are extinguished when disabled, rather than held in
a state
- Fix 'output may be truncated' warnings"
* tag 'leds-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (43 commits)
leds: lp5521: Add an error check in lp5521_post_init_device
leds: gpio: Update headers
leds: gpio: Remove unneeded assignment
leds: gpio: Move temporary variable for struct device to gpio_led_probe()
leds: gpio: Refactor code to use devm_gpiod_get_index_optional()
leds: gpio: Utilise PTR_ERR_OR_ZERO()
leds: gpio: Keep driver firmware interface agnostic
leds: core: Refactor led_update_brightness() to use standard pattern
leds: turris-omnia: Fix brightness setting and trigger activating
leds: sc27xx: Move mutex_init() down
leds: trigger: netdev: Move size check in set_device_name
leds: Add ktd202x driver
dt-bindings: leds: Add Kinetic KTD2026/2027 LED
leds: core: Add more colors from DT bindings to led_colors
dt-bindings: leds: Last color ID is now 14 (LED_COLOR_ID_LIME)
leds: tca6507: Don't use fixed GPIO base
leds: lp3952: Convert to use maple tree register cache
leds: lm392x: Convert to use maple tree register cache
leds: aw200xx: Convert to use maple tree register cache
leds: lm3601x: Convert to use maple tree register cache
...
|
|
lp55xx_write() can return an error code, add a check for this.
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231020091930.207870-1-suhui@nfschina.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Include headers which we are direct users of, no need
to have proxies.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The initial ret is not used anywhere, drop the unneeded assignment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use temporary variable for struct device in gpio_led_probe() in order
to make code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Instead of checking for the specific error codes, replace
devm_gpiod_get_index() with devm_gpiod_get_index_optional().
In this case we just return all errors to the caller and
simply check for NULL in case if legacy GPIO is being used.
As the result the code is easier to read and maintain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Avoid a boilerplate code by using PTR_ERR_OR_ZERO() in create_gpio_led().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The of.h is used as a proxy to mod_devicetable, replace former by
latter.
The commit 2d6180147e92 ("leds: gpio: Configure per-LED pin control")
added yet another unneeded OF APIs. Replace with direct use of fwnode.
Altogether this makes driver agnostic to the firmware interface in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The standard conditional pattern is to check for errors first and
bail out if any. Refactor led_update_brightness() accordingly.
While at it, drop unneeded assignment and return 0 unconditionally
on success.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Denis Osterland-Heim <denis.osterland@diehl.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231016153051.1409074-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
I have improperly refactored commits
4d5ed2621c24 ("leds: turris-omnia: Make set_brightness() more efficient")
and
aaf38273cf76 ("leds: turris-omnia: Support HW controlled mode via private trigger")
after Lee requested a change in API semantics of the new functions I
introduced in commit
28350bc0ac77 ("leds: turris-omnia: Do not use SMBUS calls").
Before the change, the function omnia_cmd_write_u8() returned 0 on
success, and afterwards it returned a positive value (number of bytes
written). The latter version was applied, but the following commits did
not properly account for this change.
This results in non-functional LED's .brightness_set_blocking() and
trigger's .activate() methods.
The main reasoning behind the semantics change was that read/write
methods should return the number of read/written bytes on success.
It was pointed to me [1] that this is not always true (for example the
regmap API does not do so), and since the driver never uses this number
of read/written bytes information, I decided to fix this issue by
changing the functions to the original semantics (return 0 on success).
[1] https://lore.kernel.org/linux-gpio/ZQnn+Gi0xVlsGCYA@smile.fi.intel.com/
Fixes: 28350bc0ac77 ("leds: turris-omnia: Do not use SMBUS calls")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20231016141538.30037-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Move the mutex_init() to avoid redundant mutex_destroy() calls after
that for each time the probe fails.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231013022010.854367-1-chunyan.zhang@unisoc.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
GCC 13.2 complains about array subscript 17 is above array bounds of
'char[16]' with IFNAMSIZ set to 16.
The warning is correct but this scenario is impossible.
set_device_name is called by device_name_store (store sysfs entry) and
netdev_trig_activate.
device_name_store already check if size is >= of IFNAMSIZ and return
-EINVAL. (making the warning scenario impossible)
netdev_trig_activate works on already defined interface, where the name
has already been checked and should already follow the condition of
strlen() < IFNAMSIZ.
Aside from the scenario being impossible, set_device_name can be
improved to both mute the warning and make the function safer.
To make it safer, move size check from device_name_store directly to
set_device_name and prevent any out of bounds scenario.
Cc: stable@vger.kernel.org
Fixes: 28a6a2ef18ad ("leds: trigger: netdev: refactor code setting device name")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309192035.GTJEEbem-lkp@intel.com/
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231007131042.15032-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This commit adds support for Kinetic KTD2026/7 RGB/White LED driver.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20231002-ktd202x-v6-2-26be8eefeb88@apitzsch.eu
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The colors are already part of DT bindings. Make sure the kernel is
able to convert them to strings.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20231008144014.1180334-1-megi@xff.cz
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
First of all, the fixed GPIO base is source of troubles and
it doesn't scale. Second, there is no in-kernel user of this
base, so drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231002135629.2605462-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-4-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-3-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-2-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-1-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
By providing a GPIO line as "trigger-sources" in the FWNODE
(such as from the device tree) and combining with the
GPIO trigger, we can support a GPIO LED trigger in a natural
way from the hardware description instead of using the
custom sysfs and deprecated global GPIO numberspace.
Example:
gpio: gpio@0 {
compatible "my-gpio";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
#trigger-source-cells = <2>;
};
leds {
compatible = "gpio-leds";
led-my-gpio {
label = "device:blue:myled";
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "gpio";
trigger-sources = <&gpio 1 GPIO_ACTIVE_HIGH>;
};
};
Make this the norm, unmark the driver as broken.
Delete the sysfs handling of GPIOs.
Since GPIO descriptors inherently can describe inversion,
the inversion handling can just be deleted.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230926-gpio-led-trigger-dt-v2-3-e06e458b788e@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Some cleanups:
* Remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other
similar things where the new entry goes _after_ the termination without
the compiler noticing.
* Drop a space from terminator entry for ID table.
While at it, move OF/ID table near to the user.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230923171921.53503-3-biju.das.jz@bp.renesas.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *pca955x_chipdefs for data in the match table.
Simplify the probe() by replacing device_get_match_data() and ID lookup
for retrieving data by i2c_get_match_data().
While at it, add const definition to pca955x_chipdefs[].
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230923171921.53503-2-biju.das.jz@bp.renesas.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect `dest` to be NUL-terminated due to its use with dev_err.
lp3952_get_label()'s dest argument is priv->leds[i].name:
| acpi_ret = lp3952_get_label(&priv->client->dev, led_name_hdl[i],
| priv->leds[i].name);
... which is then assigned to:
| priv->leds[i].cdev.name = priv->leds[i].name;
... which is used with a format string
| dev_err(&priv->client->dev,
| "couldn't register LED %s\n",
| priv->leds[i].cdev.name);
There is no indication that NUL-padding is required but if it is let's
opt for strscpy_pad.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230922-strncpy-drivers-leds-leds-lp3952-c-v1-1-4941d6f60ca4@google.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
In order to teach the compiler that 'trig->name' will never be truncated,
we need to tell it that 'cpu' is not negative.
When building with W=1, this fixes the following warnings:
drivers/leds/trigger/ledtrig-cpu.c: In function ‘ledtrig_cpu_init’:
drivers/leds/trigger/ledtrig-cpu.c:155:56: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 5 [-Werror=format-truncation=]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~
drivers/leds/trigger/ledtrig-cpu.c:155:52: note: directive argument in the range [-2147483648, 7]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~
drivers/leds/trigger/ledtrig-cpu.c:155:17: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8f88731d052d ("led-triggers: create a trigger for CPU activity")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3f4be7a99933cf8566e630da54f6ab913caac432.1695453322.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Disabling a PWM (i.e. calling pwm_apply_state with .enabled = false)
gives no guarantees what the PWM output does. It might freeze where it
currently is, or go in a High-Z state or drive the active or inactive
state, it might even continue to toggle.
To ensure that the LED gets really disabled, don't disable the PWM even
when .duty_cycle is zero.
This fixes disabling a leds-pwm LED on i.MX28. The PWM on this SoC is
one of those that freezes its output on disable, so if you disable an
LED that is full on, it stays on. If you disable a LED with half
brightness it goes off in 50% of the cases and full on in the other 50%.
Fixes: 41c42ff5dbe2 ("leds: simple driver for pwm driven LEDs")
Reported-by: Rogan Dawes <rogan@dawes.za.net>
Reported-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230922192834.1695727-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
If the MCU on Turris Omnia is running newer firmware versions, the LED
controller supports RGB gamma correction (and enables it by default for
newer boards).
Determine whether the gamma correction setting feature is supported and
add the ability to set it via sysfs attribute file.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-5-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for enabling MCU controlled mode of the Turris Omnia LEDs
via a LED private trigger called "omnia-mcu". Recall that private LED
triggers will only be listed in the sysfs trigger file for LEDs that
support them (currently there is no user of this mechanism).
When in MCU controlled mode, the user can still set LED color, but the
blinking is done by MCU, which does different things for different LEDs:
- WAN LED is blinked according to the LED[0] pin of the WAN PHY
- LAN LEDs are blinked according to the LED[0] output of the
corresponding port of the LAN switch
- PCIe LEDs are blinked according to the logical OR of the MiniPCIe port
LED pins
In the future I want to make the netdev trigger to transparently offload
the blinking to the HW if user sets compatible settings for the netdev
trigger (for LEDs associated with network devices).
There was some work on this already, and hopefully we will be able to
complete it sometime, but for now there are still multiple blockers for
this, and even if there weren't, we still would not be able to configure
HW controlled mode for the LEDs associated with MiniPCIe ports.
In the meantime let's support HW controlled mode via the private LED
trigger mechanism. If, in the future, we manage to complete the netdev
trigger offloading, we can still keep this private trigger for backwards
compatibility, if needed.
We also set "omnia-mcu" to cdev->default_trigger, so that the MCU keeps
control until the user first wants to take over it. If a different
default trigger is specified in device-tree via the
'linux,default-trigger' property, LED class will overwrite
cdev->default_trigger, and so the DT property will be respected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-4-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Implement caching of the LED color and state values that are sent to MCU
in order to make the set_brightness() operation more efficient by
avoiding I2C transactions which are not needed.
On Turris Omnia's MCU, which acts as the RGB LED controller, each LED
has a RGB color, and a ON/OFF state, which are configurable via I2C
commands CMD_LED_COLOR and CMD_LED_STATE.
The CMD_LED_COLOR command sends 5 bytes and the CMD_LED_STATE command 2
bytes over the I2C bus, which operates at 100 kHz. With I2C overhead
this allows ~1670 color changing commands and ~3200 state changing
commands per second (or around 1000 color + state changes per second).
This may seem more than enough, but the issue is that the I2C bus is
shared with another peripheral, the MCU. The MCU exposes an interrupt
interface, and it can trigger hundreds of interrupts per second. Each
time, we need to read the interrupt state register over this I2C bus.
Whenever we are sending a LED color/state changing command, the
interrupt reading is waiting.
Currently, every time LED brightness or LED multi intensity is changed,
we send a CMD_LED_STATE command, and if the computed color (brightness
adjusted multi_intensity) is non-zero, we also send a CMD_LED_COLOR
command.
Consider for example the situation when we have a netdev trigger enabled
for a LED. The netdev trigger does not change the LED color, only the
brightness (either to 0 or to currently configured brightness), and so
there is no need to send the CMD_LED_COLOR command. But each change of
brightness to 0 sends one CMD_LED_STATE command, and each change of
brightness to max_brightness sends one CMD_LED_STATE command and one
CMD_LED_COLOR command:
set_brightness(0) -> CMD_LED_STATE
set_brightness(255) -> CMD_LED_STATE + CMD_LED_COLOR
(unnecessary)
We can avoid the unnecessary I2C transactions if we cache the values of
state and color that are sent to the controller. If the color does not
change from the one previously sent, there is no need to do the
CMD_LED_COLOR I2C transaction, and if the state does not change, there
is no need to do the CMD_LED_STATE transaction.
Because we need to make sure that our cached values are consistent with
the controller state, add explicit setting of the LED color to white at
probe time (this is the default setting when MCU resets, but does not
necessarily need to be the case, for example if U-Boot played with the
LED colors).
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-3-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The leds-turris-omnia driver uses three function for I2C access:
- i2c_smbus_write_byte_data() and i2c_smbus_read_byte_data(), which
cause an emulated SMBUS transfer,
- i2c_master_send(), which causes an ordinary I2C transfer.
The Turris Omnia MCU LED controller is not semantically SMBUS, it
operates as a simple I2C bus. It does not implement any of the SMBUS
specific features, like PEC, or procedure calls, or anything. Moreover
the I2C controller driver also does not implement SMBUS, and so the
emulated SMBUS procedure from drivers/i2c/i2c-core-smbus.c is used for
the SMBUS calls, which gives an unnecessary overhead.
When I first wrote the driver, I was unaware of these facts, and I
simply used the first function that worked.
Drop the I2C SMBUS calls and instead use simple I2C transfers.
Fixes: 089381b27abe ("leds: initial support for Turris Omnia LEDs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-2-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use gpiod_set_value_cansleep in the init_device function. Without this
change, the driver may print a warning if the LP55xx enable pin is
connected to a GPIO chip which can sleep (e.g. a GPIO expander):
WARNING: CPU: 0 PID: 2719 at drivers/gpio/gpiolib.c:3051 gpiod_set_value+0x64/0xbc
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Link: https://lore.kernel.org/r/20230918143238.75600-1-eichest@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct mt6370_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915201051.never.429-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct mt6360_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915201020.never.433-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
All platform drivers below drivers/leds/ unconditionally return zero in
their remove callback and so can be converted trivially to the variant
returning void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917130947.1122198-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Make simatic_ipc_leds_gpio_remove() return void instead of returning
zero unconditionally. After that the three remove callbacks that use
this function were trivial to convert to return void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230916164516.1063380-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct lpg_led.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915201059.never.086-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct lm3697.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915201010.never.399-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct gpio_leds_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915201003.never.148-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct el15203000.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915200955.never.871-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cr0014114.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915200948.never.728-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct aw200xx.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915200938.never.767-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
When building with clang 18 I see the following warning:
| drivers/leds/leds-pca955x.c:487:15: warning: cast to smaller integer
| type 'enum pca955x_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| 487 | chip_type = (enum pca955x_type)md;
This is due to the fact that `md` is a void* while `enum pca995x_type` has the
size of an int.
Add uintptr_t cast to silence clang warning while also keeping enum cast
for readability and consistency with other `chip_type` assignment just a
few lines below:
| chip_type = (enum pca955x_type)id->driver_data;
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/1910
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230816-void-drivers-leds-leds-pca955x-v1-1-2967e4c1bdcc@google.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Instead of requiring each driver to care for assigning the owner member
of struct pwm_ops, handle that implicitly using a macro. Note that the
owner member has to be moved to struct pwm_chip, as the ops structure
usually lives in read-only memory and so cannot be modified.
The upside is that new low level drivers cannot forget the assignment and
save one line each. The pwm-crc driver didn't assign .owner, that's not
a problem in practice though as the driver cannot be compiled as a
module.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # Intel LPSS
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # pwm-{bcm,brcm}*.c
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> # sun4i
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> # pwm-visconti
Acked-by: Heiko Stuebner <heiko@sntech.de> # pwm-rockchip
Acked-by: Michael Walle <michael@walle.cc> # pwm-sl28cpld
Acked-by: Neil Armstrong <neil.armstrong@linaro.org> # pwm-meson
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230804142707.412137-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Commit c3f853184bed ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that
is always false") fixed a no-op BUG_ON. This turned out to cause a
regression, since some in-tree device-tree files already use
LED_COLOR_ID_MULTI.
Drop the BUG_ON altogether.
Fixes: c3f853184bed ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false")
Reported-by: Da Xue <da@libre.computer>
Closes: https://lore.kernel.org/linux-leds/ZQLelWcNjjp2xndY@duo.ucw.cz/T/
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918140724.18634-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add new framework to support Group Multi-Color (GMC) LEDs
- Offer an 'optional' API for non-essential LEDs
- Support obtaining 'max brightness' values from Device Tree
- Provide new led_classdev member 'color' (settable via DT and SYFS)
- Stop TTY Trigger from using the old LED_ON constraints
- Statically allocate leds_class
New Drivers:
- Add support for NXP PCA995x I2C Constant Current LED Driver
New Device Support:
- Add support for Siemens Simatic IPC BX-21 to Simatic IPC
Fix-ups:
- Some dependency / Kconfig tweaking
- Move final probe() functions back over from .probe_new()
- Simplify obtaining resources (memory, device data) using unified
API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Fix trivial styling issues; comments
- Ensure correct includes are present and remove some that are not
required
- Omit the use of redundant casts and if relevant replace with better
ones
- Use purpose-built APIs for various actions; sysfs_emit(),
module_led_trigger()
- Remove a bunch of superfluous locking
Bug Fixes:
- Ensure error codes are correctly propagated back up the call chain
- Fix incorrect error values from being returned (missing '-')
- Ensure get'ed resources are put'ed to prevent leaks
- Use correct class when exporting module resources
- Fixing rounding (or lack there of) issues
- Fix 'always false' LED_COLOR_ID_MULTI BUG() check"
* tag 'leds-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (40 commits)
leds: aw2013: Enable pull-up supply for interrupt and I2C
dt-bindings: leds: Document pull-up supply for interrupt and I2C
dt-bindings: leds: aw2013: Document interrupt
leds: uleds: Use module_misc_device macro to simplify the code
leds: trigger: netdev: Use module_led_trigger macro to simplify the code
dt-bindings: leds: Fix reference to definition of default-state
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: Make leds_class a static const structure
leds: Remove redundant of_match_ptr()
dt-bindings: leds: Add gpio-line-names to PCA9532 GPIO
leds: trigger: tty: Do not use LED_ON/OFF constants, use led_blink_set_oneshot instead
dt-bindings: leds: rohm,bd71828: Drop select:false
leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false
leds: multicolor: Use rounded division when calculating color components
leds: rgb: Add a multicolor LED driver to group monochromatic LEDs
dt-bindings: leds: Add binding for a multicolor group of LEDs
leds: class: Store the color index in struct led_classdev
leds: Provide devm_of_led_get_optional()
leds: pca995x: Fix MODULE_DEVICE_TABLE for OF
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- hp-bioscfg: New firmware-attributes driver for changing BIOS settings
from within Linux
- asus-wmi: Add charger mode, middle fan and eGPU settings support
- ideapad: Support keyboard backlight control on more models
- mellanox: Support for new models
- sel-3350: New LED and power-supply driver for this industrial
mainboard
- simatic-ipc: Add RTC battery monitor and various new models support
- miscellaneous other cleanups / fixes
* tag 'platform-drivers-x86-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (101 commits)
platform/x86: asus-wmi: corrections to egpu safety check
platform/x86: mlx-platform: Add dependency on PCI to Kconfig
platform/x86: ideapad-laptop: Add support for keyboard backlights using KBLC ACPI symbol
platform/x86/amd/pmc: Fix build error with randconfig
platform/x86/amd/pmf: Fix a missing cleanup path
watchdog: simatic: Use idiomatic selection of P2SB
platform/x86: p2sb: Make the Kconfig symbol hidden
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform: mellanox: nvsw-sn2201: change fans i2c busses.
platform: mellanox: mlxreg-hotplug: Extend condition for notification callback processing
platform: mellanox: Add initial support for PCIe based programming logic device
platform: mellanox: mlx-platform: Get interrupt line through ACPI
platform: mellanox: mlx-platform: Introduce ACPI init flow
platform: mellanox: mlx-platform: Prepare driver to allow probing through ACPI infrastructure
platform: mellanox: mlx-platform: Add reset callback
platform: mellanox: Cosmetic changes
platform: mellanox: mlx-platform: Modify power off callback
platform: mellanox: mlx-platform: add support for additional CPLD
platform: mellanox: mlx-platform: Add reset cause attribute
platform: mellanox: mlx-platform: Modify health and power hotplug action
...
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/net/inet_sock.h
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
c274af224269 ("inet: introduce inet->inet_flags")
https://lore.kernel.org/all/679ddff6-db6e-4ff6-b177-574e90d0103d@tessares.net/
Adjacent changes:
drivers/net/bonding/bond_alb.c
e74216b8def3 ("bonding: fix macvlan over alb bond support")
f11e5bd159b0 ("bonding: support balance-alb with openvswitch")
drivers/net/ethernet/broadcom/bgmac.c
d6499f0b7c7c ("net: bgmac: Return PTR_ERR() for fixed_phy_register()")
23a14488ea58 ("net: bgmac: Fix return value check for fixed_phy_register()")
drivers/net/ethernet/broadcom/genet/bcmmii.c
32bbe64a1386 ("net: bcmgenet: Fix return value check for fixed_phy_register()")
acf50d1adbf4 ("net: bcmgenet: Return PTR_ERR() for fixed_phy_register()")
net/sctp/socket.c
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
b09bde5c3554 ("inet: move inet->mc_loop to inet->inet_frags")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b655892ffd6d ("leds: trigger: netdev: expose hw_control status
via sysfs") exposed to sysfs the flag that tells whether the LED trigger
is offloaded to hardware, under the name "hw_control", since that is the
name under which this setting is called in the code.
Everywhere else in kernel when some work that is normally done in
software can be made to be done by hardware instead, we use the word
"offloading" to describe this, e.g. "LED blinking is offloaded to
hardware".
Normally renaming sysfs entries is a no-go because of backwards
compatibility. But since this patch was not yet released in a stable
kernel, I think it is still possible to rename it, if there is
consensus.
Fixes: b655892ffd6d ("leds: trigger: netdev: expose hw_control status via sysfs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230821121453.30203-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
