summaryrefslogtreecommitdiff
path: root/drivers/dma
AgeCommit message (Collapse)AuthorFilesLines
2008-10-25Merge branch 'i7300_idle' into releaseLen Brown1-2/+5
2008-10-24i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not definedVenki Pallipadi1-1/+1
When I7300_idle driver is not configured, there is a compile time warning about IDLE_IOAT_CHANNEL not defined. Fix it. Reported-by: Suresh Siddha <suresh.b.siddha@intel.com> Reported-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-24i7300_idle: Disable ioat channel only on platforms where ile driver can loadVenki Pallipadi1-1/+4
Based on input from Andi Kleen: share the platform detection code with ioat_dma and disable the channel in dma engine only for specific platforms. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-23Merge branch 'linus' into testLen Brown5-190/+100
Conflicts: MAINTAINERS arch/x86/kernel/acpi/boot.c arch/x86/kernel/acpi/sleep.c drivers/acpi/Kconfig drivers/pnp/Makefile drivers/pnp/quirks.c Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-21i7300_idle driver v1.55Andy Henroid1-0/+3
The Intel 7300 Memory Controller supports dynamic throttling of memory which can be used to save power when system is idle. This driver does the memory throttling when all CPUs are idle on such a system. Refer to "Intel 7300 Memory Controller Hub (MCH)" datasheet for the config space description. Signed-off-by: Andy Henroid <andrew.d.henroid@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
2008-10-20Merge branch 'next' of ↵Linus Torvalds5-190/+100
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: fsldma: allow Freescale Elo DMA driver to be compiled as a module fsldma: remove internal self-test from Freescale Elo DMA driver drivers/dma/dmatest.c: switch a GFP_ATOMIC to GFP_KERNEL dmatest: properly handle duplicate DMA channels drivers/dma/ioat_dma.c: drop code after return async_tx: make async_tx_run_dependencies() easier to read
2008-10-03dw_dmac: fix copy/paste bug in taskletHaavard Skinnemoen1-1/+1
The tasklet checks RAW.BLOCK twice, and does not check RAW.XFER. This is obviously wrong, and could theoretically cause the driver to hang. Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-26fsldma: allow Freescale Elo DMA driver to be compiled as a moduleTimur Tabi3-55/+94
Modify the Freescale Elo / Elo Plus DMA driver so that it can be compiled as a module. The primary change is to stop treating the DMA controller as a bus, and the DMA channels as devices on the bus. This is because the Open Firmware (OF) kernel code does not allow busses to be removed, so although we can call of_platform_bus_probe() to probe the DMA channels, there is no of_platform_bus_remove(). Instead, the DMA channels are manually probed, similar to what fsl_elbc_nand.c does. Cc: Scott Wood <scottwood@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-23fsldma: remove internal self-test from Freescale Elo DMA driverTimur Tabi1-132/+0
The Freescale Elo DMA driver runs an internal self-test before registering the channels with the DMA engine. This self-test has a fundemental flaw in that it calls the DMA engine's callback functions directly before the registration. However, the registration initializes some variables that the callback functions uses, namely the device struct. The code works today because there are two device structs: the one created by the DMA engine, and one created by the Open Firmware (OF) subsystem. The self-test currently uses the device struct created by OF. However, in the future, some of the device structs created by OF will be eliminated. This means that the self-test will only have access to the device struct created by the DMA engine. But this device struct isn't initialized when the self-test runs, and this causes a kernel panic. Since there is already a DMA test module (dmatest), the internal self-test code is not useful anyway. It is extremely unlikely that the test will fail in normal usage. It may have been helpful during development, but not any more. Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-19drivers/dma/dmatest.c: switch a GFP_ATOMIC to GFP_KERNELAndrew Morton1-1/+1
It was needlessly using the unreliable GFP_ATOMIC. Cc: Timur Tabi <timur@freescale.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-19dmatest: properly handle duplicate DMA channelsTimur Tabi1-0/+5
Update the the dmatest driver so that it handles duplicate DMA channels properly. When a DMA client is notified of an available DMA channel, it must check if it has already allocated resources for that channel. If so, it should return DMA_DUP. This can happen, for example, if a DMA driver calls dma_async_device_register() more than once. Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-13drivers/dma/ioat_dma.c: drop code after returnJulia Lawall1-2/+0
The break after the return serves no purpose. Signed-off-by: Julia Lawall <julia@diku.dk> Reviewed-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-08-09Merge branch 'for-rmk' of git://git.marvell.com/orionRussell King1-1/+1
2008-08-09[ARM] Move include/asm-arm/plat-orion to arch/arm/plat-orion/include/platLennert Buytenhek1-1/+1
This patch performs the equivalent include directory shuffle for plat-orion, and fixes up all users. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
2008-08-08Merge branch 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds1-1/+1
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB [ARM] 5166/1: magician: add MAINTAINERS entry [ARM] fix pnx4008 build errors [ARM] Fix SMP booting with non-zero PHYS_OFFSET [ARM] 5185/1: Fix spi num_chipselect for lubbock [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach [ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include [ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead [ARM] Eliminate useless includes of asm/mach-types.h [ARM] Fix circular include dependency with IRQ headers avr32: Use <mach/foo.h> instead of <asm/arch/foo.h> avr32: Introduce arch/avr32/mach-*/include/mach avr32: Move include/asm-avr32 to arch/avr32/include/asm [ARM] sa1100_wdt: use reset_status to remember watchdog reset status [ARM] pxa: introduce reset_status and clear_reset_status for driver's usage [ARM] pxa: introduce reset.h for reset specific header information
2008-08-07list.h: Add list_splice_tail() and list_splice_tail_init()Luis R. Rodriguez1-1/+1
If you are using linked lists for queues list_splice() will not do what you would expect even if you use the elements passed reversed. We need to handle these differently. We add list_splice_tail() and list_splice_tail_init(). Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-07[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/machRussell King1-1/+1
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-22I/OAT: I/OAT version 3.0 supportMaciej Sosnowski6-19/+362
This patch adds to ioatdma and dca modules support for Intel I/OAT DMA engine ver.3 (aka CB3 device). The main features of I/OAT ver.3 are: * 8 single channel DMA devices (8 channels total) * 8 DCA providers, each can accept 2 requesters * 8-bit TAG values and 32-bit extended APIC IDs Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22I/OAT: tcp_dma_copybreak default value dependent on I/OAT versionMaciej Sosnowski2-0/+17
I/OAT DMA performance tuning showed different optimal values of tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048 for 2.0). This patch lets ioatdma driver set tcp_dma_copybreak value according to these results. [dan.j.williams@intel.com: remove some ifdefs] Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22I/OAT: Add watchdog/reset functionality to ioatdmaMaciej Sosnowski2-6/+271
Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0 a watchdog has been introduced to check every 2 seconds if all channels progress normally. If stuck channel is detected, driver resets it. The reset is done in two parts. The second part is scheduled by the first one to reinitialize the channel after the restart. Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-17iop_adma: document how to calculate the minimum descriptor pool sizeDan Williams1-1/+10
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-17iop_adma: directly reclaim descriptors on allocation failureDan Williams1-2/+2
Force callers that trigger an "out of descriptors" condition to run the cleanup loop directly. Alleviates the requirement to have soft-irqs enabled when polling for a descriptor in async_xor. Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: Driver for the Synopsys DesignWare DMA controllerHaavard Skinnemoen4-0/+1357
This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: Add slave DMA interfaceHaavard Skinnemoen1-1/+15
This patch adds the necessary interfaces to the DMA Engine framework to use functionality found on most embedded DMA controllers: DMA from and to I/O registers with hardware handshaking. In this context, hardware hanshaking means that the peripheral that owns the I/O registers in question is able to tell the DMA controller when more data is available for reading, or when there is room for more data to be written. This usually happens internally on the chip, but these signals may also be exported outside the chip for things like IDE DMA, etc. A new struct dma_slave is introduced. This contains information that the DMA engine driver needs to set up slave transfers to and from a slave device. Most engines supporting DMA slave transfers will want to extend this structure with controller-specific parameters. This additional information is usually passed from the platform/board code through the client driver. A "slave" pointer is added to the dma_client struct. This must point to a valid dma_slave structure iff the DMA_SLAVE capability is requested. The DMA engine driver may use this information in its device_alloc_chan_resources hook to configure the DMA controller for slave transfers from and to the given slave device. A new operation for preparing slave DMA transfers is added to struct dma_device. This takes a scatterlist and returns a single descriptor representing the whole transfer. Another new operation for terminating all pending transfers is added as well. The latter is needed because there may be errors outside the scope of the DMA Engine framework that may require DMA operations to be terminated prematurely. DMA Engine drivers may extend the dma_device, dma_chan and/or dma_slave_descriptor structures to allow controller-specific operations. The client driver can detect such extensions by looking at the DMA Engine's struct device, or it can request a specific DMA Engine device by setting the dma_dev field in struct dma_slave. dmaslave interface changes since v4: * Fix checkpatch errors * Fix changelog (there are no slave descriptors anymore) dmaslave interface changes since v3: * Use dma_data_direction instead of a new enum * Submit slave transfers as scatterlists * Remove the DMA slave descriptor struct dmaslave interface changes since v2: * Add a dma_dev field to struct dma_slave. If set, the client can only be bound to the DMA controller that corresponds to this device. This allows controller-specific extensions of the dma_slave structure; if the device matches, the controller may safely assume its extensions are present. * Move reg_width into struct dma_slave as there are currently no users that need to be able to set the width on a per-transfer basis. dmaslave interface changes since v1: * Drop the set_direction and set_width descriptor hooks. Pass the direction and width to the prep function instead. * Declare a dma_slave struct with fixed information about a slave, i.e. register addresses, handshake interfaces and such. * Add pointer to a dma_slave struct to dma_client. Can be NULL if the DMA_SLAVE capability isn't requested. * Drop the set_slave device hook since the alloc_chan_resources hook now has enough information to set up the channel for slave transfers. Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmapDan Williams3-42/+57
In some cases client code may need the dma-driver to skip the unmap of source and/or destination buffers. Setting these flags indicates to the driver to skip the unmap step. In this regard async_xor is currently broken in that it allows the destination buffer to be unmapped while an operation is still in progress, i.e. when the number of sources exceeds the hardware channel's maximum (fixed in a subsequent patch). Acked-by: Saeed Bishara <saeed@marvell.com> Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: Add dma_client parameter to device_alloc_chan_resourcesHaavard Skinnemoen5-12/+17
A DMA controller capable of doing slave transfers may need to know a few things about the slave when preparing the channel. We don't want to add this information to struct dma_channel since the channel hasn't yet been bound to a client at this point. Instead, pass a reference to the client requesting the channel to the driver's device_alloc_chan_resources hook so that it can pick the necessary information from the dma_client struct by itself. [dan.j.williams@intel.com: fixed up fsldma and mv_xor] Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmatest: Simple DMA memcpy test clientHaavard Skinnemoen3-0/+452
This client tests DMA memcpy using various lengths and various offsets into the source and destination buffers. It will initialize both buffers with a repeatable pattern and verify that the DMA engine copies the requested region and nothing more. It will also verify that the bytes aren't swapped around, and that the source buffer isn't modified. The dmatest module can be configured to test a specific device, a specific channel. It can also test multiple channels at the same time, and it can start multiple threads competing for the same channel. Changes since v2: * Support testing multiple channels at the same time * Support testing with multiple threads competing for the same channel * Use counting test patterns in order to catch byte ordering issues Changes since v1: * Remove extra dashes around "help" * Remove "default n" from Kconfig * Turn TEST_BUF_SIZE into a module parameter * Return DMA_NAK instead of DMA_DUP * Print unhandled events * Support testing specific channels and devices * Move to the end of the Makefile Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: DMA engine driver for Marvell XOR engineSaeed Bishara4-0/+1556
The XOR engine found in Marvell's SoCs and system controllers provides XOR and DMA operation, iSCSI CRC32C calculation, memory initialization, and memory ECC error cleanup operation support. This driver implements the DMA engine API and supports the following capabilities: - memcpy - xor - memset The XOR engine can be used by DMA engine clients implemented in the kernel, one of those clients is the RAID module. In that case, I observed 20% improvement in the raid5 write throughput, and 40% decrease in the CPU utilization when doing array construction, those results obtained on an 5182 running at 500Mhz. When enabling the NET DMA client, the performance decreased, so meanwhile it is recommended to keep this client off. Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Nicolas Pitre <nico@marvell.com> Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08iop-adma: fix platform driver hotplug/coldplugKay Sievers1-0/+2
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is prefixed with "platform:". Add MODULE_ALIAS() to most of the hotpluggable platform drivers, to re-enable auto loading. Cc: <stable@kernel.org> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: track the number of clients using a channelDan Williams1-4/+10
Haavard's dma-slave interface would like to test for exclusive access to a channel. The standard channel refcounting is not sufficient in that it tracks more than just client references, it is also inaccurate as reference counts are percpu until the channel is removed. This change also enables a future fix to deallocate resources when a client declines to use a capable channel. Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: remove arch dependency from DMADEVICESDan Williams1-5/+8
The dependency is redundant since all drivers set their specific arch dependencies. The NET_DMA option is modified to be enabled only on platforms where it is known to have a positive effect. HAS_DMA is added as an explicit dependency for the DMADEVICES menu. Acked-by: Adrian Bunk <bunk@kernel.org> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08dmaengine: Couple DMA channels to their physical DMA deviceHaavard Skinnemoen1-1/+1
Set the 'parent' field of channel class devices to point to the physical DMA device initialized by the DMA engine driver. This allows drivers to use chan->dev.parent for syncing DMA buffers and adds a 'device' symlink to the real device in /sys/class/dma/dmaXchanY. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08fsldma: fix incorrect exit path for initializationLi Yang1-15/+16
Signed-off-by: Li Yang <leoli@freescale.com> Acked-by: Zhang Wei <zw@zh-kernel.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-05-20iop-adma: fixup some kzalloc/memset confusionsChristophe Jaillet1-4/+2
1) Remove an explicit memset(.., 0, ...) to a variable allocated with kzalloc (i.e. 'dest'). 2) Allocate 'src' with kmalloc instead of kzalloc as all elements of the 'src' buffer are initialized in a 'for(...)' loop just after. 3) remove useless 'sizeof(u8)', which always returns 1, when computing the size of the memory to be allocated. Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-21DMA engine: typo fixesSebastian Siewior1-3/+3
Spelling fixes for dmaengine.[ch] Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
2008-04-17dmaengine: ack to flags: make use of the unused bits in the 'ack' fieldDan Williams4-41/+44
'ack' is currently a simple integer that flags whether or not a client is done touching fields in the given descriptor. It is effectively just a single bit of information. Converting this to a flags parameter allows the other bits to be put to use to control completion actions, like dma-unmap, and capture results, like xor-zero-sum == 0. Changes are one of: 1/ convert all open-coded ->ack manipulations to use async_tx_ack and async_tx_test_ack. 2/ set the ack bit at prep time where possible 3/ make drivers store the flags at prep time 4/ add flags to the device_prep_dma_interrupt prototype Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17iop-adma: remove the workaround for missed interrupts on iop3xxDan Williams1-5/+0
This workaround was covering the dependency submission bug in async_tx. Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17async_tx: kill ->device_dependency_addedDan Williams4-28/+0
DMA drivers no longer need to be notified of dependency submission events as async_tx_run_dependencies and async_tx_channel_switch will handle the scheduling and execution of dependent operations. [sfr@canb.auug.org.au: extend this for fsldma] Acked-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17async_tx: fix multiple dependency submissionDan Williams2-6/+5
Shrink struct dma_async_tx_descriptor and introduce async_tx_channel_switch to properly inject a channel switch interrupt in the descriptor stream. This simplifies the locking model as drivers no longer need to handle dma_async_tx_descriptor.lock. Acked-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.Zhang Wei1-5/+21
Split MPC83xx EOCDI event from MPC85xx EOLNI event, which is also need to update cookie and start the next transfer. The DMA channel irq handler function code is refined. The patch is tested on MPC8377MDS board. Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by; Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.Zhang Wei2-18/+3
Always enabling the fsl_dma_self_test() to ensure the DMA controller should works well after the driver probed. Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-31[POWERPC] fsldma: Use compatiable binding as specKumar Gala1-4/+4
Documentation/powerpc/booting-without-of.txt specifies the compatiables we should bind to for this driver (elo, eloplus). Use these instead of the extremely specific 'mpc8540' and 'mpc8349' compatiables. Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-30fix the broken annotations in fsldmaAl Viro1-20/+27
a) every bitwise declaration will give a unique type; use typedefs. b) no need to bother with the stuff pointed to by iomem pointers, unless it's accessed directly. noderef will force us to use helpers anyway. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-30ioat_dca __iomem annotationsAl Viro1-2/+2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-18fsldma: Fix the DMA halt when using DMA_INTERRUPT async_tx transfer.Zhang Wei2-0/+31
The DMA_INTERRUPT async_tx is a NULL transfer, thus the BCR(count register) is 0. When the transfer started with a byte count of zero, the DMA controller will triger a PE(programming error) event and halt, not a normal interrupt. I add special codes for PE event and DMA_INTERRUPT async_tx testing. Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13iop-adma.c: replace remaining __FUNCTION__ occurrencesHarvey Harrison1-16/+16
__FUNCTION__ is gcc-specific, use __func__ Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13fsldma: Add a completed cookie updated action in DMA finish interrupt.Zhang Wei1-1/+1
The patch 'fsldma: do not cleanup descriptors in hardirq context' (commit 222ccf9ab838a1ca7163969fabd2cddc10403fb5) removed descriptors cleanup function to tasklet but the completed cookie do not updated. Thus, the DMA controller will get lots of duplicated transfer interrupts. Just make a completed cookie update in interrupt handler. And keep other cleanup jobs in tasklet function. Tested-by: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13fsldma: Add device_prep_dma_interrupt support to fsldma.cZhang Wei1-0/+27
This is a bug that I assigned DMA_INTERRUPT capability to fsldma but missing device_prep_dma_interrupt function. For a bug in dmaengine.c the driver passed BUG_ON() checking. The patch fixes it. Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13dmaengine: Fix a bug about BUG_ON() on DMA engine capability DMA_INTERRUPT.Zhang Wei1-1/+1
The device->device_prep_dma_interrupt function is used by DMA_INTERRUPT capability, not DMA_ZERO_SUM. Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13fsldma: Fix fsldma.c warning messages when it's compiled under PPC64.Zhang Wei1-13/+16
There are warning messages reported by Stephen Rothwell with ARCH=powerpc allmodconfig build: drivers/dma/fsldma.c: In function 'fsl_dma_prep_memcpy': drivers/dma/fsldma.c:439: warning: comparison of distinct pointer types lacks a cast drivers/dma/fsldma.c: In function 'fsl_chan_xfer_ld_queue': drivers/dma/fsldma.c:584: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'dma_addr_t' drivers/dma/fsldma.c: In function 'fsl_dma_chan_do_interrupt': drivers/dma/fsldma.c:668: warning: format '%x' expects type 'unsigned int', but argument 5 has type 'dma_addr_t' drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'dma_addr_t' drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long unsigned int', but argument 5 has type 'dma_addr_t' drivers/dma/fsldma.c:701: warning: format '%02x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t' drivers/dma/fsldma.c: In function 'fsl_dma_self_test': drivers/dma/fsldma.c:840: warning: format '%d' expects type 'int', but argument 5 has type 'size_t' drivers/dma/fsldma.c: In function 'of_fsl_dma_probe': drivers/dma/fsldma.c:1010: warning: format '%08x' expects type 'unsigned int', but argument 5 has type 'resource_size_t' This patch fixed the above warning messages. Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-17 01:34:49 +0000