| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The variable pm_flags is used to prevent APM from being enabled
along with ACPI, which would lead to problems. However, acpi_init()
is always called before apm_init() and after acpi_init() has
returned, it is known whether or not ACPI will be used. Namely, if
acpi_disabled is not set after acpi_init() has returned, this means
that ACPI is enabled. Thus, it is sufficient to check acpi_disabled
in apm_init() to prevent APM from being enabled in parallel with
ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
|
|
If direct references to pm_flags are removed from drivers/acpi/bus.c,
CONFIG_ACPI will not need to depend on CONFIG_PM any more. Make that
happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
|
|
Since acpi_bus_set_power() should not use __acpi_bus_get_power() to
update the device's device->power.state field before changing its
power state (this may cause device->power.state to be inconsistent
with the device power resources' reference counters), remove this
call from it. In consequence, the acpi_power_nocheck variable is not
necessary any more, so it can be dropped along with the DMI table
used for setting that variable for HP Pavilion 05.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There are no more users of acpi_bus_get_power(), so it can be
dropped. Moreover, it should be dropped, because it modifies
the device->power.state field of an ACPI device without updating
the reference counters of the device's power resources, which is
wrong.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Use the new function acpi_bus_update_power() for manipulating power
resources used by ACPI fan devices, which allows them to be put into
the right state during initialization and resume. Consequently,
remove the flags.force_power_state field from struct acpi_device,
which is not necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The ACPI device driver used for handling power resources,
acpi_power_driver, creates a struct acpi_power_resource object for
each ACPI device representing a power resource. These objects are
then used when setting and reading the power states of devices using
the corresponding power resources. Unfortunately, acpi_power_driver
is registered after acpi_scan_init() that may add devices using the
power resources before acpi_power_driver has a chance to create
struct acpi_power_resource objects for them (specifically, the power
resources may be referred to during the scanning process through
acpi_bus_get_power() before they have been initialized).
As the first step towards fixing this issue, move the registration
of acpi_power_driver into acpi_scan_init() so that power resource
devices can be initialized by it as soon as they have been found in
the namespace.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add function acpi_bus_update_power() for reading the actual power
state of an ACPI device and updating its device->power.state field
in such a way that its power resources' reference counters will
remain consistent with that field.
For this purpose introduce __acpi_bus_set_power() setting the
power state of an ACPI device without updating its
device->power.state field and make acpi_bus_set_power() and
acpi_bus_update_power() use it (acpi_bus_set_power() retains the
current behavior for now).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add function acpi_bus_init_power() for getting the initial power
state of an ACPI device and reference counting its power resources
as appropriate.
Make acpi_bus_get_power_flags() use the new function instead of
acpi_bus_get_power() that updates device->power.state without
reference counting the device's power resources.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
It sometimes is necessary to get the power state of an ACPI device
without updating its device->power.state field, for example to
avoid inconsistencies between device->power.state and the reference
counters of the device's power resources. For this purpose introduce
__acpi_bus_get_power() that will return the given device's power
state via a pointer (instead of modifying device->power.state)
and make acpi_bus_get_power() use it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
acpi_power_get_inferred_state() should not update
device->power.state behind the back of its caller, so make it return
the state via a pointer instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
ACPI table sysfs I/F is broken by commit
78f1699659963fff97975df44db6d5dbe7218e55
Author: Alex Chiang <achiang@hp.com>
Date: Sun Dec 20 12:19:09 2009 -0700
ACPI: processor: call _PDC early
because dynamic SSDT tables may be loaded in _PDC,
before installing the ACPI table handler.
As a result, the sysfs I/F of these dynamic tables are
located at /sys/firmware/acpi/tables instead of
/sys/firmware/acpi/tables/dynamic, which is not true.
Invoke acpi_sysfs_init() before acpi_early_processor_set_pdc(),
so that the table handler is installed before any dynamic tables loaded.
https://bugzilla.kernel.org/show_bug.cgi?id=21142
CC: Dennis Jansen <dennis.jansen@web.de>
CC: Alex Chiang <achiang@hp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
'bugzilla-14736', 'bugzilla-14679', 'bugzilla-16396', 'launchpad-613381' and 'misc' into release
|
|
Our list of Toshiba Satellite models that require this workaround
is growing -- so invoke the workaround for the entire product line.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Rmove deprecated ACPI procfs I/F, including
/proc/acpi/debug_layer
/proc/acpi/debug_level
/proc/acpi/info
/proc/acpi/dsdt
/proc/acpi/fadt
/proc/acpi/sleep
because the sysfs I/F is already available
and has been working well for years.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Introduce drivers/acpi/sysfs.c.
code for ACPI sysfs I/F, including
#ifdef ACPI_DEBUG
/sys/module/acpi/parameters/debug_layer
/sys/module/acpi/parameters/debug_level
/sys/module/acpi/parameters/trace_method_name
/sys/module/acpi/parameters/trace_debug_layer
/sys/module/acpi/parameters/trace_debug_level
/sys/module/acpi/parameters/trace_state
#endif
/sys/module/acpi/parameters/acpica_version
/sys/firmware/acpi/tables/
/sys/firmware/acpi/interrupts/
is moved to this file.
No function change in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Introduce drivers/acpi/debugfs.c.
Code for ACPI debugfs I/F,
i.e. /sys/kernel/debug/acpi/custom_method,
is moved to this file.
And make ACPI debugfs always built in,
even if CONFIG_ACPI_DEBUG is cleared.
BTW:this adds about 400bytes code to ACPI, when
CONFIG_ACPI_DEBUG is cleared.
[uaccess.h build fix from Andrew Morton <akpm@linux-foundation.org>]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Remove own implementation of hex_to_bin().
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (22 commits)
ACPI: fix early DSDT dmi check warnings on ia64
ACPICA: Update version to 20100428.
ACPICA: Update/clarify some parameter names associated with acpi_handle
ACPICA: Rename acpi_ex_system_do_suspend->acpi_ex_system_do_sleep
ACPICA: Prevent possible allocation overrun during object copy
ACPICA: Split large file, evgpeblk
ACPICA: Add GPE support for dynamically loaded ACPI tables
ACPICA: Clarify/rename some root table descriptor fields
ACPICA: Update version to 20100331.
ACPICA: Minimize the differences between linux GPE code and ACPICA code base
ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT
ACPICA: Update DSDT copy/detection.
ACPICA: Add subsystem option to force copy of DSDT to local memory
ACPICA: Add detection of corrupted/replaced DSDT
ACPICA: Add write support for DataTable operation regions
ACPICA: Fix for acpi_reallocate_root_table for incorrect root table copy
ACPICA: Update comments/headers, no functional change
ACPICA: Update version to 20100304
ACPICA: Fix for possible fault in acpi_ex_release_mutex
ACPICA: Standardize integer output for ACPICA warnings/errors
...
|
|
WARNING: at drivers/firmware/dmi_scan.c:423 dmi_matches+0x70/0x160()
dmi check: not initialized yet.
This is caused by commit aa2110c
(ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT).
DMI is not initialized yet in acpi_early_init on ia64.
The DSDT DMI check table is x86 specific, so make it empty on other archs.
And this fixes the warnings on ia64.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This addresses: https://bugzilla.kernel.org/show_bug.cgi?id=14998
We copy some strings into "event" but we leave the space after the NULL
terminators uninitialized. Later in acpi_bus_receive_event() we copy
the whole struct to another buffer with memcpy(). If the new buffer is
stored on the stack, kmemcheck prints a warning about the unitialized
space after the NULL terminators.
It's true that the space is uninitialized, but it's harmless. The
buffer is only used in acpi_system_read_event() and we don't read past
the NULL terminators.
This patch changes the kmalloc() to kzalloc() so that we initialize the
memory and silence the kmemcheck warning.
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some BIOS on Toshiba machines corrupt the DSDT, so add a new
boot option acpi=copy_dsdt to workaround it.
Add warning message to ask users to use this option if corrupt DSDT detected.
Also build a DMI blacklist to check it and automatically copy DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
'bugzilla-531916-power-state', 'ht-warn-2.6.34', 'pnp', 'processor-rename', 'sony-2.6.34', 'suse-bugzilla-531547', 'tz-check', 'video' and 'misc-2.6.34' into release
|
|
If the BIOS pokes the system-wide OSC bits to see if Linux
supports evaluating _OST after a _PPC change notification,
answer yes.
Also, fix an oversight where we neglected to set the OSC
bit advertising processor aggregator device support
when acpi-pad is compiled as a module.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
If the ACPI power state can be got both directly and indirectly,
we prefer to get it indirectly.
https://bugzilla.redhat.com/show_bug.cgi?id=531916 describes a
system with a _PSC method for the fan that always returns "on".
There's no benefit in us always requesting the state of the fan
when performing transitions - we want to do everything we can
to ensure that the fan turns on when it should do, not risk
hardware damage by believing the hardware when it tells us the
fan is already on. Given that the Leading Other OS(tm) works fine
on this machine, it seems likely that it behaves in much this way.
inspired-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
release
|
|
Executing _OSC returns a buffer, which has an acpi object in it.
Don't directly returns the buffer, instead, we return the acpi object's
buffer. This fixes a regression since caller of acpi_run_osc expects
an acpi object's buffer returned.
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
We discovered that at least one machine (HP Envy), methods in the DSDT
attempt to call external methods defined in a dynamically loaded SSDT.
Unfortunately, the DSDT methods we are trying to call are part of the
EC initialization, which happens very early, and the the dynamic SSDT
is only loaded when a processor _PDC method runs much later.
This results in namespace lookup errors for the (as of yet) undefined
methods.
Since Windows doesn't have any issues with this machine, we take it
as a hint that they must be evaluating _PDC much earlier than we are.
Thus, the proper thing for Linux to do should be to match the Windows
implementation more closely.
Provide a mechanism to call _PDC before we enable the EC. Doing so loads
the dynamic tables, and allows the EC to be enabled correctly.
The ACPI processor driver will still evaluate _PDC in its .add() method
to cover the hotplug case.
Resolves: http://bugzilla.kernel.org/show_bug.cgi?id=14824
Cc: ming.m.lin@intel.com
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
v2->v1:
.improve debug info as suggedted by Bjorn,Kenji
.API is using uuid string as suggested by Alexey
Add an API to execute _OSC. A lot of devices can have this method, so add a
generic API.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add acpi_bus_get_status_handle() so we can get the status of a namespace
object before building a struct acpi_device.
This removes a use of "device->flags.dynamic_status", a cached indicator of
whether _STA exists. It seems simpler and more reliable to just evaluate
_STA and catch AE_NOT_FOUND errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Conflicts:
drivers/pci/dmar.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
users of acpi.h that need dmi.h should include it directly.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Handler was never invoked. Now invoked if/when host node is deleted.
Data object was not automatically deleted when host node was deleted.
Interface to handler had an unused parameter, removed it.
ACPICA BZ 778.
http://acpica.org/bugzilla/show_bug.cgi?id=778
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch changes the global system notification path so it uses the
acpi_handle, not the acpi_device.
System notifications often deal with device presence and status change.
In these cases, we may not have an acpi_device. For example, we may
get a Device Check notification on an object that previously was not
present. Since the object was not present, we would not have had an
acpi_device for it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Remove return values from acpi_bus_check_device() and acpi_bus_check_scope()
since nobody looks at them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Remove "status_changed" return from acpi_bus_check_device(). Nobody
does anything useful based on its value.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This replaces several messages that depend on the acpi_device struct
with a single message that uses just the acpi_handle. We should be
able to deal with notifications to objects that do not yet have an
acpi_device struct.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
System notify events (0x00-0x7f) are common across all device types
and should be handled in Linux/ACPI, not in drivers. However, some
BIOSes use system notify events in device-specific ways that require
the driver to be involved.
This patch adds a ACPI_DRIVER_ALL_NOTIFY_EVENTS driver flag. When a
driver sets this flag and supplies a .notify method, Linux/ACPI calls
the .notify method for ALL notify events on the device, not just the
device-specific (0x80-0xff) events.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
"Transitioning device [%s] to D%d" is not correct.
We print this line when we attempted to transition
the device, and it failed.
So instead, print
"Device [%s] failed to transition to D%d\n"
This can happen under two conditions:
1. acpi_power_transition() fails when trying to handle the
_ON/_OFF for associated power resource.
2. acpi_evaluate_object() on the explicit _PS0/_PS3
for that actual device could fail.
this change clarifies, but doesn't fix
http://bugzilla.kernel.org/show_bug.cgi?id=13243
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
This patch makes acpi_init() call acpi_wakeup_device_init() directly.
Previously, acpi_wakeup_device_init() was a late_initcall (sequence 7).
acpi_wakeup_device_init() depends on acpi_wakeup_device_list, which
is populated when ACPI devices are enumerated by acpi_init() ->
acpi_scan_init(). Using late_initcall is certainly enough to make
sure acpi_wakeup_device_list is populated, but it is more than
necessary. We can just as easily call acpi_wakeup_device_init()
directly from acpi_init(), which avoids the initcall magic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch makes acpi_init() call acpi_sleep_proc_init() directly.
Previously, acpi_sleep_proc_init() was a late_initcall (sequence 7),
apparently to make sure that the /proc hierarchy already exists:
2003/02/13 12:38:03-06:00 mochel
acpi sleep: demote sleep proc file creation.
- Make acpi_sleep_proc_init() a late_initcall(), and not called from
acpi_sleep_init(). This guarantees that the acpi proc hierarchy is at
least there when we create the dang file.
This should no longer be an issue because acpi_bus_init() (called early
in acpi_init()) creates acpi_root_dir (/proc/acpi).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch makes acpi_init() call init_acpi_device_notify() directly.
Previously, init_acpi_device_notify() was an arch_initcall (sequence 3),
so it was called before acpi_init() (a subsys_initcall at sequence 4).
init_acpi_device_notify() sets the platform_notify and
platform_notify_remove function pointers. These pointers
are not used until acpi_init() enumerates ACPI devices in
this path:
acpi_init()
acpi_scan_init()
acpi_bus_scan()
acpi_add_single_object()
acpi_device_register()
device_add()
<use platform_notify>
So it is sufficient to have acpi_init() call init_acpi_device_notify()
directly before it enumerates devices.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch makes acpi_init() call acpi_debug_init() directly.
Previously, both were subsys_initcalls. acpi_debug_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch makes acpi_init() call acpi_system_init() directly.
Previously, both were subsys_initcalls. acpi_system_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch makes acpi_init() call acpi_power_init() directly.
Previously, both were subsys_initcalls. acpi_power_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch makes acpi_init() call acpi_ec_init() directly.
Previously, both were subsys_initcalls. acpi_ec_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch makes acpi_init() call acpi_scan_init() directly.
Previously, both acpi_init() and acpi_scan_init() were subsys_initcalls,
and acpi_init() was called first based on the link order from the
makefile (bus.o before scan.o).
acpi_scan_init() registers the ACPI bus type, creates the root device,
and enumerates fixed-feature and namespace devices. All of this must
be done after acpi_init(), and it's better to call acpi_scan_init()
explicitly rather than rely on the link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
