| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The missing "compatible" entries are needed by drivers/clk/ti/clkctrl.c,
and without them the structures initialized in drivers/clk/ti/clk-814x.c
are not passed to configuration code. The result is a "not found from
clkctrl data" error message, although boot proceeds anyway.
The reason why the compatible is not found is because the board specific
files override the SoC compatible without including it. This did not
cause any issues until with the clkctrl nodes got introduced.
Very lightly tested on a (lurching) AM3874 design that's in the middle
of a kernel upgrade from TI's abandoned 2.6.37 tree.
Also tested on j5eco-evm and hp-t410 to verify the clkctrl clocks are
found.
Fixes: bb30465b5902 ("ARM: dts: dm814x: add clkctrl nodes")
Fixes: 80a06c0d8357 ("ARM: dts: dm816x: add clkctrl nodes")
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony: updated to fix for 8168-evm, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch disable mmc nodes by default in the dm814x.dtsi and
enable only when needed on a given dts
v2: Disable un-used mmc nodes on the related boards dts files
instead of from the included SOC dts
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] dm814x TRM: SPRUGZ8F: 11.2.4.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add NAND support for dm8148-evm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add usb support for dm814x-evm
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is a mmc slot on the dm8148-evm that's wired to the sd_1
interface.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like I made a typo on the control base, all the 81xx
SoCs have it at 0x48140000 base. We've just gotten away with
the typo as the Ethernet phy was configured by the bootloader
on my test system and we're not yet using the pinctrl.
In addition to fixing the contol base, we need to also use the
right Ethernet phy flags to initialize it. And we are still
missing the PLL driver for dm814x and only relying on the
divider and mux clocks.
Fixes: f3d953ea3721 ("ARM: dts: Add minimal dm814x support")
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add minimal dts support for dm8148-evm.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
