| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use correct HCI ISO data packet header struct when the packet has
timestamp. The timestamp, when present, goes before the other fields
(Core v5.3 4E 5.4.5), so the structs are not compatible.
Fixes: ccf74f2390d6 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This removes the code introduced by
14202eff214e1e941fefa0366d4c3bc4b1a0d500 as hci_recv_frame is now able
to detect ACL packets that are in fact ISO packets.
Fixes: 14202eff214e ("Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packet")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Because some transports don't have a dedicated type for ISO packets
(see 14202eff214e1e941fefa0366d4c3bc4b1a0d500) they may use ACL type
when in fact they are ISO packets.
In the past this was left for the driver to detect such thing but it
creates a problem when using the likes of btproxy when used by a VM as
the host would not be aware of the connection the guest is doing it
won't be able to detect such behavior, so this make bt_recv_frame
detect when it happens as it is the common interface to all drivers
including guest VMs.
Fixes: 14202eff214e ("Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packet")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The address resolution should be disabled during the active scan,
so all the advertisements can reach the host. The advertising
has to be paused before disabling the address resolution,
because the advertising will prevent any changes to the resolving
list and the address resolution status. Skipping this will cause
the hci error and the discovery failure.
According to the bluetooth specification:
"7.8.44 LE Set Address Resolution Enable command
This command shall not be used when:
- Advertising (other than periodic advertising) is enabled,
- Scanning is enabled, or
- an HCI_LE_Create_Connection, HCI_LE_Extended_Create_Connection, or
HCI_LE_Periodic_Advertising_Create_Sync command is outstanding."
If the host is using RPA, the controller needs to generate RPA for
the advertising, so the advertising must remain paused during the
active scan.
If the host is not using RPA, the advertising can be resumed after
disabling the address resolution.
Fixes: 9afc675edeeb ("Bluetooth: hci_sync: allow advertise when scan without RPA")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Local port is a 10-bit number, but it was mistakenly stored in a u8,
resulting in firmware errors when using a netdev corresponding to a
local port higher than 255.
Fix by storing the local port in u16, as is done in the rest of the
code.
Fixes: bf73904f5fba ("mlxsw: Add support for 802.1Q FID family")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/eace1f9d96545ab8a2775db857cb7e291a9b166b.1679398549.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The DMA address returned by dma_map_single() should be checked with
dma_mapping_error(). Fix it accordingly.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/6645a4b5c1e364312103f48b7b36783b94e197a2.1679370343.git.fthain@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vladimir Oltean says:
====================
Fix trainwreck with Ocelot switch statistics counters
While testing the patch set for preemptible traffic classes with some
controlled traffic and measuring counter deltas:
https://lore.kernel.org/netdev/20230220122343.1156614-1-vladimir.oltean@nxp.com/
I noticed that in the output of "ethtool -S swp0 --groups eth-mac
eth-phy eth-ctrl rmon -- --src emac | grep -v ': 0'", the TX counters
were off. Quickly I realized that their values were permutated by 1
compared to their names, and that for example
tx-rmon-etherStatsPkts64to64Octets was incrementing when
tx-rmon-etherStatsPkts65to127Octets should have.
Initially I suspected something having to do with the bulk reading
logic, and indeed I found a bug there (fixed as 1/3), but that was not
the source of the problems. Instead it revealed other problems.
While dumping the regions created by the driver on my switch, I figured
out that it sees a discontinuity which shouldn't have existed between
reg 0x278 and reg 0x280.
Discontinuity between last reg 0x0 and new reg 0x0, creating new region
Discontinuity between last reg 0x108 and new reg 0x200, creating new region
Discontinuity between last reg 0x278 and new reg 0x280, creating new region
Discontinuity between last reg 0x2b0 and new reg 0x400, creating new region
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 31 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 13 contiguous counters starting with SYS:STAT:CNT[0x0a0]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
That is where TX_MM_HOLD should have been, and that was the bug, since
it was missing. After adding it, the regions look like this and the
off-by-one issue is resolved:
Discontinuity between last reg 0x000000 and new reg 0x000000, creating new region
Discontinuity between last reg 0x000108 and new reg 0x000200, creating new region
Discontinuity between last reg 0x0002b0 and new reg 0x000400, creating new region
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 45 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
However, as I am thinking out loud, it should have not reported the
other counters as off by one even when skipping TX_MM_HOLD... after all,
on Ocelot/Seville, there are more counters which need to be skipped.
Which is when I investigated and noticed the bug solved in 2/3.
I've validated that both on native VSC9959 (which uses
ocelot_mm_stats_layout) as well as by faking the other switches by
making VSC9959 use the plain ocelot_stats_layout.
To summarize: on all Ocelot switches, the TX counters and drop counters
are completely broken. The RX counters are mostly fine.
With this occasion, I have collected more cleanup patches in this area,
which I'm going to submit after the net -> net-next merge.
====================
Link: https://lore.kernel.org/r/20230321010325.897817-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The lack of a definition for this counter is what initially prompted me
to investigate a problem which really manifested itself as the previous
change, "net: mscc: ocelot: fix transfer from region->buf to ocelot->stats".
When TX_MM_HOLD is defined in enum ocelot_stat but not in struct
ocelot_stat_layout ocelot_mm_stats_layout, this creates a hole, which
due to the aforementioned bug, makes all counters following TX_MM_HOLD
be recorded off by one compared to their correct position. So for
example, a non-zero TX_PMAC_OCTETS would be reported as TX_MERGE_FRAGMENTS,
TX_PMAC_UNICAST would be reported as TX_PMAC_OCTETS, TX_PMAC_64 would be
reported as TX_PMAC_PAUSE, etc etc. This is because the size of the hole
(1) is much smaller than the size of the region, so the phenomenon where
the stats are off-by-one, rather than lost, prevails.
However, the phenomenon where stats are lost can be seen too, for
example with DROP_LOCAL, which is at the beginning of its own region
(offset 0x000400 vs the previous 0x0002b0 constitutes a discontinuity).
This is also reported as off by one and saved to TX_PMAC_1527_MAX, but
that counter is not reported to the unstructured "ethtool -S", as
opposed to DROP_LOCAL which is (as "drop_local").
Fixes: ab3f97a9610a ("net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To understand the problem, we need some definitions.
The driver is aware of multiple counters (enum ocelot_stat), yet not all
switches supported by the driver implement all counters. There are 2
statistics layouts: ocelot_stats_layout and ocelot_mm_stats_layout, the
latter having 36 counters more than the former.
ocelot->stats[] is not a compact array, i.e. there are elements within
it which are not going to be populated for ocelot_stats_layout. On the
other hand, ocelot->stats[] is easily indexable, for example "tx_octets"
for port 3 can be found at ocelot->stats[3 * OCELOT_NUM_STATS +
OCELOT_STAT_TX_OCTETS], and that is why we keep it sparse.
Regions, as created by ocelot_prepare_stats_regions(), are compact
(every element from region->buf will correspond to a counter that is
present in this switch's layout) but are not easily indexable.
Let's define holes as the ranges of values of enum ocelot_stat for which
ocelot_stats_layout doesn't have a "reg" defined. For example, there is
a hole between OCELOT_STAT_RX_GREEN_PRIO_7 and OCELOT_STAT_TX_OCTETS
which is of 23 elements that are only present on ocelot_mm_stats_layout,
and as such, they are also present in enum ocelot_stat. Let's define the
left extremity of the hole - the last enum ocelot_stat still defined -
as A (in this case OCELOT_STAT_RX_GREEN_PRIO_7) and the right extremity -
the first enum ocelot_stat that is defined after a series of undefined
ones - as B (in this case OCELOT_STAT_TX_OCTETS).
There is a bug in the procedure which transfers stats from region->buf[]
to ocelot->stats[].
For each hole in the ocelot_stats_layout, the logic transfers the stats
starting with enum ocelot_stat B to ocelot->stats[] index A + 1. So all
stats after a hole are saved to a position which is off by B - A + 1
elements.
This causes 2 kinds of issues:
(a) counters which shouldn't increment increment
(b) counters which should increment don't
Holes in the ocelot_stat_layout automatically imply the end of a region
and the beginning of a new one; however the reverse is not necessarily
true. For example, for ocelot_mm_stat_layout, there could be multiple
regions (which indicate discontinuities in register addresses) while
there is no hole (which indicates discontinuities in enum ocelot_stat
values).
In the example above, the stats from the second region->buf[] are not
transferred to ocelot->stats starting with index
"port * OCELOT_NUM_STATS + OCELOT_STAT_TX_OCTETS" as they should, but
rather, starting with element
"port * OCELOT_NUM_STATS + OCELOT_STAT_RX_GREEN_PRIO_7 + 1".
That stats[] array element is not reported to user space for switches
that use ocelot_stat_layout, and that is how issue (b) occurs.
However, if the length of the second region is larger than the hole,
then some stats will start to be transferred to the ocelot->stats[]
indices which *are* reported to user space, but those indices contain
wrong values (corresponding to unexpected counters). This is how issue
(a) occurs.
The procedure, as it was introduced in commit d87b1c08f38a ("net: mscc:
ocelot: use bulk reads for stats"), was not buggy, because there were no
holes in the struct ocelot_stat_layout instances at that time. The
problem is that when those holes were introduced, the function was not
updated to take them into consideration.
To update the procedure, we need to know, for each region, which enum
ocelot_stat corresponds to its region->base. We have no way of deducing
that based on the contents of struct ocelot_stats_region, so we need to
add this information.
Fixes: ab3f97a9610a ("net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The blamed commit changed struct ocelot_stat_layout :: "u32 offset" to
"u32 reg".
However, "u32 reg" is not quite a register address, but an enum
ocelot_reg, which in itself encodes an enum ocelot_target target in the
upper bits, and an index into the ocelot->map[target][] array in the
lower bits.
So, whereas the previous code comparison between stats_layout[i].offset
and last + 1 was correct (because those "offsets" at the time were
32-bit relative addresses), the new code, comparing layout[i].reg to
last + 4 is not correct, because the "reg" here is an enum/index, not an
actual register address.
What we want to compare are indeed register addresses, but to do that,
we need to actually go through the same motions as
__ocelot_bulk_read_ix() itself.
With this bug, all statistics counters are deemed by
ocelot_prepare_stats_regions() as constituting their own region.
(Truncated) log on VSC9959 (Felix) below (prints added by me):
Before:
region of 1 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x001]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x002]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x041]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x042]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x081]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x0ac]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x100]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x101]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x111]
After:
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 45 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
Since commit d87b1c08f38a ("net: mscc: ocelot: use bulk reads for
stats") intended bulking as a performance improvement, and since now,
with trivial-sized regions, performance is even worse than without
bulking at all, this could easily qualify as a performance regression.
Fixes: d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers should not assume skb_mac_header(skb) == skb->data in their
ndo_start_xmit().
Use skb_network_offset() and skb_transport_offset() which
better describe what is needed in erspan_fb_xmit() and
ip6erspan_tunnel_xmit()
syzbot reported:
WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 skb_mac_header include/linux/skbuff.h:2873 [inline]
WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962
Modules linked in:
CPU: 0 PID: 5083 Comm: syz-executor406 Not tainted 6.3.0-rc2-syzkaller-00866-gd4671cb96fa3 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023
RIP: 0010:skb_mac_header include/linux/skbuff.h:2873 [inline]
RIP: 0010:ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962
Code: 04 02 41 01 de 84 c0 74 08 3c 03 0f 8e 1c 0a 00 00 45 89 b4 24 c8 00 00 00 c6 85 77 fe ff ff 01 e9 33 e7 ff ff e8 b4 27 a1 f8 <0f> 0b e9 b6 e7 ff ff e8 a8 27 a1 f8 49 8d bf f0 0c 00 00 48 b8 00
RSP: 0018:ffffc90003b2f830 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 000000000000ffff RCX: 0000000000000000
RDX: ffff888021273a80 RSI: ffffffff88e1bd4c RDI: 0000000000000003
RBP: ffffc90003b2f9d8 R08: 0000000000000003 R09: 000000000000ffff
R10: 000000000000ffff R11: 0000000000000000 R12: ffff88802b28da00
R13: 00000000000000d0 R14: ffff88807e25b6d0 R15: ffff888023408000
FS: 0000555556a61300(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055e5b11eb6e8 CR3: 0000000027c1b000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__netdev_start_xmit include/linux/netdevice.h:4900 [inline]
netdev_start_xmit include/linux/netdevice.h:4914 [inline]
__dev_direct_xmit+0x504/0x730 net/core/dev.c:4300
dev_direct_xmit include/linux/netdevice.h:3088 [inline]
packet_xmit+0x20a/0x390 net/packet/af_packet.c:285
packet_snd net/packet/af_packet.c:3075 [inline]
packet_sendmsg+0x31a0/0x5150 net/packet/af_packet.c:3107
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0xde/0x190 net/socket.c:747
__sys_sendto+0x23a/0x340 net/socket.c:2142
__do_sys_sendto net/socket.c:2154 [inline]
__se_sys_sendto net/socket.c:2150 [inline]
__x64_sys_sendto+0xe1/0x1b0 net/socket.c:2150
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f123aaa1039
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 b1 14 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffc15d12058 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f123aaa1039
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000020000040 R09: 0000000000000014
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f123aa648c0
R13: 431bde82d7b634db R14: 0000000000000000 R15: 0000000000000000
Fixes: 1baf5ebf8954 ("erspan: auto detect truncated packets.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230320163427.8096-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are memory leaks reported by kmemleak:
unreferenced object 0xffff888106500800 (size 128):
comm "modprobe", pid 1017, jiffies 4297787785 (age 67.152s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000970ce626>] __kmem_cache_alloc_node+0x20c/0x380
[<00000000fb5f78d9>] kmalloc_trace+0x2f/0xb0
[<000000000e947e2a>] idt77252_init_one+0x2847/0x3c90 [idt77252]
[<000000006efb048e>] local_pci_probe+0xeb/0x1a0
...
unreferenced object 0xffff888106500b00 (size 128):
comm "modprobe", pid 1017, jiffies 4297787785 (age 67.152s)
hex dump (first 32 bytes):
00 20 3d 01 80 88 ff ff 00 20 3d 01 80 88 ff ff . =...... =.....
f0 23 3d 01 80 88 ff ff 00 20 3d 01 00 00 00 00 .#=...... =.....
backtrace:
[<00000000970ce626>] __kmem_cache_alloc_node+0x20c/0x380
[<00000000fb5f78d9>] kmalloc_trace+0x2f/0xb0
[<00000000f451c5be>] alloc_scq.constprop.0+0x4a/0x400 [idt77252]
[<00000000e6313849>] idt77252_init_one+0x28cf/0x3c90 [idt77252]
The root cause is traced to the vc_maps which alloced in open_card_oam()
are not freed in close_card_oam(). The vc_maps are used to record
open connections, so when close a vc_map in close_card_oam(), the memory
should be freed. Moreover, the ubr0 is not closed when close a idt77252
device, leading to the memory leak of vc_map and scq_info.
Fix them by adding kfree in close_card_oam() and implementing new
close_card_ubr0() to close ubr0.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Link: https://lore.kernel.org/r/20230320143318.2644630-1-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When BCM63xx internal switches are connected to switches with a 4-byte
Broadcom tag, it does not identify the packet as VLAN tagged, so it adds one
based on its PVID (which is likely 0).
Right now, the packet is received by the BCM63xx internal switch and the 6-byte
tag is properly processed. The next step would to decode the corresponding
4-byte tag. However, the internal switch adds an invalid VLAN tag after the
6-byte tag and the 4-byte tag handling fails.
In order to fix this we need to remove the invalid VLAN tag after the 6-byte
tag before passing it to the 4-byte tag decoding.
Fixes: 964dbf186eaa ("net: dsa: tag_brcm: add support for legacy tags")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230319095540.239064-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the free_percpu for the allocated "vf->hw.lmt_info" in order to avoid
memory leak, same as the "pf->hw.lmt_info" in
`drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c`.
Fixes: 5c0512072f65 ("octeontx2-pf: cn10k: Use runtime allocated LMTLINE region")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Link: https://lore.kernel.org/r/20230317064337.18198-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Geoff Levand says:
====================
net/ps3_gelic_net: DMA related fixes
v9: Make rx_skb_size local to gelic_descr_prepare_rx.
v8: Add more cpu_to_be32 calls.
v7: Remove all cleanups, sync to spider net.
v6: Reworked and cleaned up patches.
v5: Some additional patch cleanups.
v4: More patch cleanups.
v3: Cleaned up patches as requested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current Gelic Etherenet driver was checking the return value of its
dma_map_single call, and not using the dma_mapping_error() routine.
Fixes runtime problems like these:
DMA-API: ps3_gelic_driver sb_05: device driver failed to check map error
WARNING: CPU: 0 PID: 0 at kernel/dma/debug.c:1027 .check_unmap+0x888/0x8dc
Fixes: 02c1889166b4 ("ps3: gigabit ethernet driver for PS3, take3")
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Gelic Ethernet device needs to have the RX sk_buffs aligned to
GELIC_NET_RXBUF_ALIGN, and also the length of the RX sk_buffs must
be a multiple of GELIC_NET_RXBUF_ALIGN.
The current Gelic Ethernet driver was not allocating sk_buffs large
enough to allow for this alignment.
Also, correct the maximum and minimum MTU sizes, and add a new
preprocessor macro for the maximum frame size, GELIC_NET_MAX_FRAME.
Fixes various randomly occurring runtime network errors.
Fixes: 02c1889166b4 ("ps3: gigabit ethernet driver for PS3, take3")
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clang with W=1 reports
drivers/net/usb/plusb.c:65:1: error:
unused function 'pl_clear_QuickLink_features' [-Werror,-Wunused-function]
pl_clear_QuickLink_features(struct usbnet *dev, int val)
^
This static function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet length retrieved from descriptor may be larger than
the actual socket buffer length. In such case the cloned
skb passed up the network stack will leak kernel memory contents.
Additionally prevent integer underflow when size is less than
ETH_FCS_LEN.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In emac_probe, &adpt->work_thread is bound with
emac_work_thread. Then it will be started by timeout
handler emac_tx_timeout or a IRQ handler emac_isr.
If we remove the driver which will call emac_remove
to make cleanup, there may be a unfinished work.
The possible sequence is as follows:
Fix it by finishing the work before cleanup in the emac_remove
and disable timeout response.
CPU0 CPU1
|emac_work_thread
emac_remove |
free_netdev |
kfree(netdev); |
|emac_reinit_locked
|emac_mac_down
|//use netdev
Fixes: b9b17debc69d ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We collect the software statistics counters for RX bytes (reported to
/proc/net/dev and to ethtool -S $dev | grep 'rx_bytes: ") at a time when
skb->len has already been adjusted by the eth_type_trans() ->
skb_pull_inline(skb, ETH_HLEN) call to exclude the L2 header.
This means that when connecting 2 DSA interfaces back to back and
sending 1 packet with length 100, the sending interface will report
tx_bytes as incrementing by 100, and the receiving interface will report
rx_bytes as incrementing by 86.
Since accounting for that in scripts is quirky and is something that
would be DSA-specific behavior (requiring users to know that they are
running on a DSA interface in the first place), the proposal is that we
treat it as a bug and fix it.
This design bug has always existed in DSA, according to my analysis:
commit 91da11f870f0 ("net: Distributed Switch Architecture protocol
support") also updates skb->dev->stats.rx_bytes += skb->len after the
eth_type_trans() call. Technically, prior to Florian's commit
a86d8becc3f0 ("net: dsa: Factor bottom tag receive functions"), each and
every vendor-specific tagging protocol driver open-coded the same bug,
until the buggy code was consolidated into something resembling what can
be seen now. So each and every driver should have its own Fixes: tag,
because of their different histories until the convergence point.
I'm not going to do that, for the sake of simplicity, but just blame the
oldest appearance of buggy code.
There are 2 ways to fix the problem. One is the obvious way, and the
other is how I ended up doing it. Obvious would have been to move
dev_sw_netstats_rx_add() one line above eth_type_trans(), and below
skb_push(skb, ETH_HLEN). But DSA processing is not as simple as that.
We count the bytes after removing everything DSA-related from the
packet, to emulate what the packet's length was, on the wire, when the
user port received it.
When eth_type_trans() executes, dsa_untag_bridge_pvid() has not run yet,
so in case the switch driver requests this behavior - commit
412a1526d067 ("net: dsa: untag the bridge pvid from rx skbs") has the
details - the obvious variant of the fix wouldn't have worked, because
the positioning there would have also counted the not-yet-stripped VLAN
header length, something which is absent from the packet as seen on the
wire (there it may be untagged, whereas software will see it as
PVID-tagged).
Fixes: f613ed665bb3 ("net: dsa: Add support for 64-bit statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cooling levels array is supposed to prevent the system fans from
being configured below a 20% duty cycle as otherwise some of them get
stuck at 0 RPM.
Due to an off-by-one error, the last element in the array was not
initialized, causing it to be set to zero, which in turn lead to fans
being configured with a 0% duty cycle in maximum cooling state.
Since commit 332fdf951df8 ("mlxsw: thermal: Fix out-of-bounds memory
accesses") the contents of the array are static. Therefore, instead of
fixing the initialization of the array, simply remove it and adjust
thermal_cooling_device_ops::set_cur_state() so that the configured duty
cycle is never set below 20%.
Before:
# cat /sys/class/thermal/thermal_zone0/cdev0/type
mlxsw_fan
# echo 10 > /sys/class/thermal/thermal_zone0/cdev0/cur_state
# cat /sys/class/hwmon/hwmon0/name
mlxsw
# cat /sys/class/hwmon/hwmon0/pwm1
0
After:
# cat /sys/class/thermal/thermal_zone0/cdev0/type
mlxsw_fan
# echo 10 > /sys/class/thermal/thermal_zone0/cdev0/cur_state
# cat /sys/class/hwmon/hwmon0/name
mlxsw
# cat /sys/class/hwmon/hwmon0/pwm1
255
This bug was uncovered when the thermal subsystem repeatedly tried to
configure the cooling devices to their maximum state due to another
issue [1]. This resulted in the fans being stuck at 0 RPM, which
eventually lead to the system undergoing thermal shutdown.
[1] https://lore.kernel.org/netdev/ZA3CFNhU4AbtsP4G@shredder/
Fixes: a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew reports that the SFF modules on one of the ZII platforms do not
indicate link up due to the SFP code believing that LOS indicating that
there is no signal being received from the remote end, but in fact the
LOS signal is showing that there is signal.
What makes SFF modules different from SFPs is they typically have an
inverted LOS, which uncovered this issue. When we read the hardware
state, we mask it with state_hw_mask so we ignore anything we're not
interested in. However, we don't re-read when state_hw_mask changes,
leading to sfp->state being stale.
Arrange for a software poll of the module state after we have parsed
the EEPROM in sfp_sm_mod_probe() and updated state_*_mask. This will
generate any necessary events for signal changes for the state
machine as well as updating sfp->state.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 8475c4b70b04 ("net: sfp: re-implement soft state polling setup")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently DMA address width is either read from a RO device register
or force set from the platform data. This breaks DMA when the host DMA
address width is <=32it but the device is >32bit.
Right now the driver may decide to use a 2nd DMA descriptor for
another buffer (happens in case of TSO xmit) assuming that 32bit
addressing is used due to platform configuration but the device will
still use both descriptor addresses as one address.
This can be observed with the Intel EHL platform driver that sets
32bit for addr64 but the MAC reports 40bit. The TX queue gets stuck in
case of TCP with iptables NAT configuration on TSO packets.
The logic should be like this: Whatever we do on the host side (memory
allocation GFP flags) should happen with the host DMA width, whenever
we decide how to set addresses on the device registers we must use the
device DMA address width.
This patch renames the platform address width field from addr64 (term
used in device datasheet) to host_addr and uses this value exclusively
for host side operations while all chip operations consider the device
DMA width as read from the device register.
Fixes: 7cfc4486e7ea ("stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing")
Signed-off-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
ACPI/DT mdiobus module owner fixes
This patch series fixes wrong mdiobus module ownership for MDIO buses
registered from DT or ACPI.
Thanks Maxime for providing the first patch and making me see that ACPI
also had the same issue.
Changes in v2:
- fixed missing kdoc in the first patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bus ownership is wrong when using acpi_mdiobus_register() to register an
mdio bus. That function is not inline, so when it calls
mdiobus_register() the wrong THIS_MODULE value is captured.
CC: Maxime Bizon <mbizon@freebox.fr>
Fixes: 803ca24d2f92 ("net: mdio: Add ACPI support code for mdio")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bus ownership is wrong when using of_mdiobus_register() to register an mdio
bus. That function is not inline, so when it calls mdiobus_register() the wrong
THIS_MODULE value is captured.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
[florian: fix kdoc, added Fixes tag]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the phy_disconnect() -> phy_stop() path, we will be forcibly setting
the PHY state machine to PHY_HALTED. This invalidates the old_state !=
phydev->state condition in phy_state_machine() such that we will neither
display the state change for debugging, nor will we invoke the
link_change_notify() callback.
Factor the code by introducing phy_process_state_change(), and ensure
that we process the state change from phy_stop() as well.
Fixes: 5c5f626bcace ("net: phy: improve handling link_change_notify callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-16 (igb, igbvf, igc)
This series contains updates to igb, igbvf, and igc drivers.
Lin Ma removes rtnl_lock() when disabling SRIOV on remove which was
causing deadlock on igb.
Akihiko Odaki delays enabling of SRIOV on igb to prevent early messages
that could get ignored and clears MAC address when PF returns nack on
reset; indicating no MAC address was assigned for igbvf.
Gaosheng Cui frees IRQs in error path for igbvf.
Akashi Takahiro fixes logic on checking TAPRIO gate support for igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In xirc2ps_probe, the local->tx_timeout_task was bounded
with xirc2ps_tx_timeout_task. When timeout occurs,
it will call xirc_tx_timeout->schedule_work to start the
work.
When we call xirc2ps_detach to remove the driver, there
may be a sequence as follows:
Stop responding to timeout tasks and complete scheduled
tasks before cleanup in xirc2ps_detach, which will fix
the problem.
CPU0 CPU1
|xirc2ps_tx_timeout_task
xirc2ps_detach |
free_netdev |
kfree(dev); |
|
| do_reset
| //use dev
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have to make sure that the info returned by the helper is valid
before using it.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: f990c82c385b ("qed*: Add support for ndo_set_vf_trust")
Fixes: 733def6a04bf ("qed*: IOV link control")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-16 (iavf)
This series contains updates to iavf driver only.
Alex fixes incorrect check against Rx hash feature and corrects payload
value for IPv6 UDP packet.
Ahmed removes bookkeeping of VLAN 0 filter as it always exists and can
cause a false max filter error message.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: do not track VLAN 0 filters
iavf: fix non-tunneled IPv6 UDP packet type and hashing
iavf: fix inverted Rx hash condition leading to disabled hash
====================
Link: https://lore.kernel.org/r/20230316155316.1554931-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CPTS PPS GENf adjustment settings are invalid after it has been
disabled for a while, so reset them.
Fixes: eb9233ce6751 ("net: ethernet: ti: am65-cpts: adjust pps following ptp changes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20230316095232.2002680-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Packet length retrieved from descriptor may be larger than
the actual socket buffer length. In such case the cloned
skb passed up the network stack will leak kernel memory contents.
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230316101954.75836-1-szymon.heidrich@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CPU port should also be enabled in order to get a working switch.
Fixes: a5538a777b73 ("net: dsa: b53: mmap: Add device tree support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230316172807.460146-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, wifi and ipsec.
A little more changes than usual, but it's pretty normal for us that
the rc3/rc4 PRs are oversized as people start testing in earnest.
Possibly an extra boost from people deploying the 6.1 LTS but that's
more of an unscientific hunch.
Current release - regressions:
- phy: mscc: fix deadlock in phy_ethtool_{get,set}_wol()
- virtio: vsock: don't use skbuff state to account credit
- virtio: vsock: don't drop skbuff on copy failure
- virtio_net: fix page_to_skb() miscalculating the memory size
Current release - new code bugs:
- eth: correct xdp_features after device reconfig
- wifi: nl80211: fix the puncturing bitmap policy
- net/mlx5e: flower:
- fix raw counter initialization
- fix missing error code
- fix cloned flow attribute
- ipa:
- fix some register validity checks
- fix a surprising number of bad offsets
- kill FILT_ROUT_CACHE_CFG IPA register
Previous releases - regressions:
- tcp: fix bind() conflict check for dual-stack wildcard address
- veth: fix use after free in XDP_REDIRECT when skb headroom is small
- ipv4: fix incorrect table ID in IOCTL path
- ipvlan: make skb->skb_iif track skb->dev for l3s mode
- mptcp:
- fix possible deadlock in subflow_error_report
- fix UaFs when destroying unaccepted and listening sockets
- dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290
Previous releases - always broken:
- tcp: tcp_make_synack() can be called from process context, don't
assume preemption is disabled when updating stats
- netfilter: correct length for loading protocol registers
- virtio_net: add checking sq is full inside xdp xmit
- bonding: restore IFF_MASTER/SLAVE flags on bond enslave Ethertype
change
- phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit number
- eth: i40e: fix crash during reboot when adapter is in recovery mode
- eth: ice: avoid deadlock on rtnl lock when auxiliary device
plug/unplug meets bonding
- dsa: mt7530:
- remove now incorrect comment regarding port 5
- set PLL frequency and trgmii only when trgmii is used
- eth: mtk_eth_soc: reset PCS state when changing interface types
Misc:
- ynl: another license adjustment
- move the TCA_EXT_WARN_MSG attribute for tc action"
* tag 'net-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
selftests: bonding: add tests for ether type changes
bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails
bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change
net: renesas: rswitch: Fix GWTSDIE register handling
net: renesas: rswitch: Fix the output value of quote from rswitch_rx()
ethernet: sun: add check for the mdesc_grab()
net: ipa: fix some register validity checks
net: ipa: kill FILT_ROUT_CACHE_CFG IPA register
net: ipa: add two missing declarations
net: ipa: reg: include <linux/bug.h>
net: xdp: don't call notifiers during driver init
net/sched: act_api: add specific EXT_WARN_MSG for tc action
Revert "net/sched: act_api: move TCA_EXT_WARN_MSG to the correct hierarchy"
net: dsa: microchip: fix RGMII delay configuration on KSZ8765/KSZ8794/KSZ8795
ynl: make the tooling check the license
ynl: broaden the license even more
tools: ynl: make definitions optional again
hsr: ratelimit only when errors are printed
qed/qed_mng_tlv: correctly zero out ->min instead of ->hour
selftests: net: devlink_port_split.py: skip test if no suitable device available
...
|
|
Pull block fixes from Jens Axboe:
"A bit bigger than usual, as the NVMe pull request missed last weeks
submission. In detail:
- NVMe pull request via Christoph:
- Avoid potential UAF in nvmet_req_complete (Damien Le Moal)
- More quirks (Elmer Miroslav Mosher Golovin, Philipp Geulen)
- Fix a memory leak in the nvme-pci probe teardown path
(Irvin Cote)
- Repair the MAINTAINERS entry (Lukas Bulwahn)
- Fix handling single range discard request (Ming Lei)
- Show more opcode names in trace events (Minwoo Im)
- Fix nvme-tcp timeout reporting (Sagi Grimberg)
- MD pull request via Song:
- Two fixes for old issues (Neil)
- Resource leak in device stopping (Xiao)
- Bio based device stats fix (Yu)
- Kill unused CONFIG_BLOCK_COMPAT (Lukas)
- sunvdc missing mdesc_grab() failure check (Liang)
- Fix for reversal of request ordering upon issue for certain cases
(Jan)
- null_blk timeout fixes (Damien)
- Loop use-after-free fix (Bart)
- blk-mq SRCU fix for BLK_MQ_F_BLOCKING devices (Chris)"
* tag 'block-6.3-2023-03-16' of git://git.kernel.dk/linux:
block: remove obsolete config BLOCK_COMPAT
md: select BLOCK_LEGACY_AUTOLOAD
block: count 'ios' and 'sectors' when io is done for bio-based device
block: sunvdc: add check for mdesc_grab() returning NULL
nvmet: avoid potential UAF in nvmet_req_complete()
nvme-trace: show more opcode names
nvme-tcp: add nvme-tcp pdu size build protection
nvme-tcp: fix opcode reporting in the timeout handler
nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM620
nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV3000
nvme-pci: fixing memory leak in probe teardown path
nvme: fix handling single range discard request
MAINTAINERS: repair malformed T: entries in NVM EXPRESS DRIVERS
block: null_blk: cleanup null_queue_rq()
block: null_blk: Fix handling of fake timeout request
blk-mq: fix "bad unlock balance detected" on q->srcu in __blk_mq_run_dispatch_ops
loop: Fix use-after-free issues
block: do not reverse request order when flushing plug list
md: avoid signed overflow in slot_store()
md: Free resources in __md_stop
|
|
Pull io_uring fixes from Jens Axboe:
- When PF_NO_SETAFFINITY was removed for io-wq threads, we kind of
forgot about the SQPOLL thread. Remove it there as well, there's even
less of a reason to set it there (Michal)
- Fixup a confusing 'ret' setting (Li)
- When MSG_RING is used to send a direct descriptor to another ring,
it's possible to have it allocate it on the target ring rather than
provide a specific index for it. If this is done, return the chosen
value in the CQE, like we would've done locally (Pavel)
- Fix a regression in this series on huge page bvec collapsing (Pavel)
* tag 'io_uring-6.3-2023-03-16' of git://git.kernel.dk/linux:
io_uring/rsrc: fix folio accounting
io_uring/msg_ring: let target know allocated index
io_uring: rsrc: Optimize return value variable 'ret'
io_uring/sqpoll: Do not set PF_NO_SETAFFINITY on sqpoll threads
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an error code path issue in a cpuidle driver and make the
sleepgraph utility more robust against unexpected input.
Specifics:
- Fix the psci_pd_init_topology() failure path in the PSCI cpuidle
driver (Shawn Guo)
- Modify the sleepgraph utility so it does not crash on binary data
in device names (Todd Brandt)"
* tag 'pm-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
pm-graph: sleepgraph: Avoid crashing on binary data in device names
cpuidle: psci: Iterate backwards over list in psci_pd_remove()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These add some new quirks, fix PPTT handling, fix an ACPI utility and
correct a mistake in the ACPI documentation.
Specifics:
- Fix ACPI PPTT handling to avoid sleep in the atomic context when it
is not present (Sudeep Holla)
- Add 'backlight=native' DMI quirk for Dell Vostro 15 3535 to the
ACPI video driver (Chia-Lin Kao)
- Add ACPI quirks for I2C device enumeration on Lenovo Yoga Book X90
and Acer Iconia One 7 B1-750 (Hans de Goede)
- Fix handling of invalid command line option values in the ACPI
pfrut utility (Chen Yu)
- Fix references to I2C device data type in the ACPI documentation
for device enumeration (Andy Shevchenko)"
* tag 'acpi-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: tools: pfrut: Check if the input of level and type is in the right numeric range
ACPI: PPTT: Fix to avoid sleep in the atomic context when PPTT is absent
ACPI: x86: Add skip i2c clients quirk for Lenovo Yoga Book X90
ACPI: x86: Add skip i2c clients quirk for Acer Iconia One 7 B1-750
ACPI: x86: Introduce an acpi_quirk_skip_gpio_event_handlers() helper
ACPI: video: Add backlight=native DMI quirk for Dell Vostro 15 3535
ACPI: docs: enumeration: Correct reference to the I²C device data type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat fweaks and fixes from Len Brown:
"Leprechaun sized fixes and tweaks touching only turbostat.
'Keeping happy users happy since 2010'"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2023.03.17
tools/power turbostat: fix decoding of HWP_STATUS
tools/power turbostat: Introduce support for EMR
tools/power turbostat: remove stray newlines from warn/warnx strings
tools/power turbostat: Fix /dev/cpu_dma_latency warnings
tools/power turbostat: Provide better debug messages for failed capabilities accesses
tools/power turbostat: update dump of SECONDARY_TURBO_RATIO_LIMIT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- cleanup for xen time handling
- enable the VGA console in a Xen PVH dom0
- cleanup in the xenfs driver
* tag 'for-linus-6.3-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: remove unnecessary (void*) conversions
x86/PVH: obtain VGA console info in Dom0
x86/xen/time: cleanup xen_tsc_safe_clocksource
xen: update arch/x86/include/asm/xen/cpuid.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- fixes to the ASID allocator to avoid leaking stale mappings between
tasks
- fix the vmalloc fault handler to tolerate huge pages
* tag 'riscv-for-linus-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: mm: Support huge page in vmalloc_fault()
riscv: asid: Fixup stale TLB entry cause application crash
Revert "riscv: mm: notify remote harts about mmu cache updates"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Update defconfigs
- Fix early boot code by adding missing intersection check to prevent
potential overwriting of the ipl report
- Fix a use-after-free issue in s390-specific code related to PCI
resources being retained after hot-unplugging individual functions,
by removing the resources from the PCI bus's resource list and using
the zpci_bar_struct's resource pointer directly
* tag 's390-6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
PCI: s390: Fix use-after-free of PCI resources with per-function hotplug
s390/ipl: add missing intersection check to ipl_report handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix false detection of read faults, introduced by execute-only
support
- Fix a build failure when GENERIC_ALLOCATOR is not selected
Thanks to Russell Currey, Randy Dunlap, Michal Suchánek, Nathan Lynch,
and Benjamin Gray.
* tag 'powerpc-6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix false detection of read faults
powerpc/pseries: RTAS work area requires GENERIC_ALLOCATOR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- dw_mmc-starfive: Fix initialization of the prev_err variable
- sdhci_am654: Lower power-on failed message severity
* tag 'mmc-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: dw_mmc-starfive: Fix initialization of prev_err
mmc: sdhci_am654: lower power-on failed message severity
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing surprising, a collection of small device-specific fixes.
The majority of changes are for ASoC Intel stuff, while a few other
ASoC and HD-audio fixes are found"
* tag 'sound-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
ALSA: hda/ca0132: fixup buffer overrun at tuning_ctl_set()
ALSA: asihpi: check pao in control_message()
ASoC: hdmi-codec: only startup/shutdown on supported streams
ASoC: da7219: Initialize jack_det_mutex
ALSA: hda: Match only Intel devices with CONTROLLER_IN_GPU()
ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro
ALSA: hda/realtek: fix speaker, mute/micmute LEDs not work on a HP platform
ALSA: hda: intel-dsp-config: add MTL PCI id
ASoC: SOF: IPC4: update gain ipc msg definition to align with fw
ASoC: SOF: sof-audio: don't squelch errors in WIDGET_SETUP phase
ASoC: SOF: Intel: hda-ctrl: re-add sleep after entering and exiting reset
ASoC: SOF: Intel: hda-dsp: harden D0i3 programming sequence
ASoC: SOF: ipc4-topology: set dmic dai index from copier
ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP
ASoC: SOF: Intel: pci-tng: revert invalid bar size setting
ASoC: SOF: topology: Fix error handling in sof_widget_ready()
ASoC: Intel: soc-acpi: fix copy-paste issue in topology names
ASoC: SOF: ipc4-topology: Fix incorrect sample rate print unit
ASoC: SOF: ipc3: Check for upper size limit for the received message
ASOC: SOF: Intel: pci-tgl: Fix device description
...
|
|
Pull drm fixes from Dave Airlie:
"Seems like a pretty regular rc3, i915 and amdgpu with the usual
selection of fixes, then a scattering of fixes across misc drivers and
other areas:
accel:
- build fix for accel
edid:
- fix info leak in edid
ttm:
- fix NULL ptr deref
- reference counting fix
i915:
- Fix hwmon PL1 power limit enabling
- Fix audio ELD handling for DP MST
- Fix PSR io and wake line calculations
- Fix DG2 HDMI modes with 267.30 and 319.89 MHz pixel clocks
- Fix SSEU subslice out-of-bounds access
- Fix misuse of non-idle barriers as fence trackers
amdgpu:
- SMU 13 update
- RDNA2 suspend/resume fix when overclocking is enabled
- SRIOV VCN fixes
- HDCP suspend/resume fix
- Fix drm polling splat regression
- Fix dirty rectangle tracking for PSR
- Fix vangogh regression on certain BIOSes
- Misc display fixes
- Suspend/resume IOMMU regression fix
amdkfd:
- Fix BO offset for multi-VMA page migration
- Fix a possible double free
- Fix potential use after free
- Fix process cleanup on module exit
bridge:
- fix returned array size name documentation
fbdev:
- ref-counting fix for fbdev deferred I/O
virtio:
- dma sync fix
shmem-helper:
- error path fix
msm:
- shrinker blocking fix
panfrost:
- shrinker rpm fix
chipsfb:
- fix error code
meson:
- fix 1px pink line
- fix regulator interaction
sun4i:
- fix missing component unbind"
* tag 'drm-fixes-2023-03-17' of git://anongit.freedesktop.org/drm/drm: (38 commits)
drm/ttm: drop extra ttm_bo_put in ttm_bo_cleanup_refs
drm/amdgpu: Don't resume IOMMU after incomplete init
drm/amdkfd: Fixed kfd_process cleanup on module exit.
drm/amd/display: disconnect MPCC only on OTG change
drm/amd/display: Fix DP MST sinks removal issue
drm/amd/display: Do not set DRR on pipe Commit
drm/amd/display: Remove OTG DIV register write for Virtual signals.
drm/meson: dw-hdmi: Fix devm_regulator_*get_enable*() conversion again
drm/bridge: Fix returned array size name for atomic_get_input_bus_fmts kdoc
drm/amdgpu/vcn: Disable indirect SRAM on Vangogh broken BIOSes
drm/amdgpu/nv: fix codec array for SR_IOV
drm/amd/display: Write to correct dirty_rect
drm/amdgpu: move poll enabled/disable into non DC path
drm/amd/display: Fix HDCP failing to enable after suspend
drm/amdkfd: fix potential kgd_mem UAFs
drm/amdgpu/vcn: custom video info caps for sriov
drm/amd/pm: Fix sienna cichlid incorrect OD volage after resume
drm/amd/pm: bump SMU 13.0.4 driver_if header version
drm/amdkfd: fix a potential double free in pqm_create_queue
drm/amdkfd: Get prange->offset after svm_range_vram_node_new
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Ten patches, eight in drivers and two in the core, which correct a
regression from directory removal and add a no VPD size quirk also to
fix a regression. All pretty small"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: mcq: Use active_reqs to check busy in clock scaling
scsi: core: Fix a procfs host directory removal regression
scsi: core: Add BLIST_NO_VPD_SIZE for some VDASD
scsi: mpi3mr: Fix expander node leak in mpi3mr_remove()
scsi: mpi3mr: Fix memory leaks in mpi3mr_init_ioc()
scsi: mpi3mr: Fix sas_hba.phy memory leak in mpi3mr_remove()
scsi: mpi3mr: Fix mpi3mr_hba_port memory leak in mpi3mr_remove()
scsi: mpi3mr: Fix config page DMA memory leak
scsi: mpi3mr: Fix throttle_groups memory leak
scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add()
|
|
Merge a PSCI cpuidle driver fix for 6.3-rc1:
- Fix the psci_pd_init_topology() failure path in the PSCI cpuidle
driver (Shawn Guo).
* pm-cpuidle:
cpuidle: psci: Iterate backwards over list in psci_pd_remove()
|
