diff options
| author | Dhruva Gole <d-gole@ti.com> | 2023-01-25 13:40:23 +0530 |
|---|---|---|
| committer | Mark Brown <broonie@kernel.org> | 2023-02-14 13:25:26 +0000 |
| commit | d403fb6e76bf854ef0f7d84e797e51b9494788e0 (patch) | |
| tree | 19d35b2b65e8e6b1a18310d6454f2274725cb67e /drivers/spi | |
| parent | a8674ae02db232927385c2d0a063e10c0118f5ca (diff) | |
spi: cadence-quadspi: use STIG mode for small reads
Fix the issue where some flash chips like cypress S25HS256T return the
value of the same register over and over in DAC mode.
For example in the TI K3-AM62x Processors refer [0] Technical Reference
Manual there is a layer of digital logic in front of the QSPI/OSPI
Drive when used in DAC mode. This is part of the Flash Subsystem (FSS)
which provides access to external Flash devices.
The FSS0_0_SYSCONFIG Register (Offset = 4h) has a BIT Field for
OSPI_32B_DISABLE_MODE which has a Reset value = 0. This means, OSPI 32bit
mode enabled by default.
Thus, by default controller operates in 32 bit mode causing it to always
align all data to 4 bytes from a 4byte aligned address. In some flash
chips like cypress for example if we try to read some regs in DAC mode
then it keeps sending the value of the first register that was requested
and inorder to read the next reg, we have to stop and re-initiate a new
transaction.
This causes wrong register values to be read than what is desired when
registers are read in DAC mode. Hence if the data.nbytes is very less
then prefer STIG mode for such small reads.
[0] https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-5-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Diffstat (limited to 'drivers/spi')
| -rw-r--r-- | drivers/spi/spi-cadence-quadspi.c | 8 |
1 files changed, 7 insertions, 1 deletions
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c index a6d0f1b0bb49..2954c06a7f57 100644 --- a/drivers/spi/spi-cadence-quadspi.c +++ b/drivers/spi/spi-cadence-quadspi.c @@ -1359,7 +1359,13 @@ static int cqspi_mem_process(struct spi_mem *mem, const struct spi_mem_op *op) cqspi_configure(f_pdata, mem->spi->max_speed_hz); if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) { - if (!op->addr.nbytes) + /* + * Performing reads in DAC mode forces to read minimum 4 bytes + * which is unsupported on some flash devices during register + * reads, prefer STIG mode for such small reads. + */ + if (!op->addr.nbytes || + op->data.nbytes <= CQSPI_STIG_DATA_LEN_MAX) return cqspi_command_read(f_pdata, op); return cqspi_read(f_pdata, op); |