From 85cd7251b9112e3dabeac9fd3b175601ca607241 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Thu, 31 Aug 2006 00:03:49 -0400 Subject: [libata #pata-drivers] Trim trailing whitespace. --- drivers/ata/pata_hpt3x2n.c | 94 +++++++++++++++++++++++----------------------- 1 file changed, 47 insertions(+), 47 deletions(-) (limited to 'drivers/ata/pata_hpt3x2n.c') diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c index 40fcda62c7a2..06c8db079b91 100644 --- a/drivers/ata/pata_hpt3x2n.c +++ b/drivers/ata/pata_hpt3x2n.c @@ -65,7 +65,7 @@ struct hpt_chip { * PIO. * 31 FIFO enable. */ - + /* 66MHz DPLL clocks */ static struct hpt_clock hpt3x2n_clocks[] = { @@ -100,11 +100,11 @@ static struct hpt_clock hpt3x2n_clocks[] = { * is hard coded but easy to change. This will be needed if we use * different DPLLs */ - + static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed) { struct hpt_clock *clocks = hpt3x2n_clocks; - + while(clocks->xfer_speed) { if (clocks->xfer_speed == speed) return clocks->timing; @@ -121,52 +121,52 @@ static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed) * Perform the initial reset handling for the 3x2n series controllers. * Reset the hardware and state machine, obtain the cable type. */ - + static int hpt3xn_pre_reset(struct ata_port *ap) { u8 scr2, ata66; struct pci_dev *pdev = to_pci_dev(ap->host->dev); - + pci_read_config_byte(pdev, 0x5B, &scr2); pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); /* Cable register now active */ pci_read_config_byte(pdev, 0x5A, &ata66); /* Restore state */ pci_write_config_byte(pdev, 0x5B, scr2); - + if (ata66 & (1 << ap->port_no)) ap->cbl = ATA_CBL_PATA40; else ap->cbl = ATA_CBL_PATA80; /* Reset the state machine */ - pci_write_config_byte(pdev, 0x50, 0x37); - pci_write_config_byte(pdev, 0x54, 0x37); + pci_write_config_byte(pdev, 0x50, 0x37); + pci_write_config_byte(pdev, 0x54, 0x37); udelay(100); return ata_std_prereset(ap); } - + /** * hpt3x2n_error_handler - probe the hpt3x2n bus * @ap: ATA port to reset * * Perform the probe reset handling for the 3x2N */ - + static void hpt3x2n_error_handler(struct ata_port *ap) { ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset); } - + /** * hpt3x2n_set_piomode - PIO setup * @ap: ATA interface * @adev: device on the interface * - * Perform PIO mode setup. + * Perform PIO mode setup. */ - + static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); @@ -177,12 +177,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); addr2 = 0x51 + 4 * ap->port_no; - + /* Fast interrupt prediction disable, hold off interrupt disable */ pci_read_config_byte(pdev, addr2, &fast); fast &= ~0x07; pci_write_config_byte(pdev, addr2, fast); - + pci_read_config_dword(pdev, addr1, ®); mode = hpt3x2n_find_mode(ap, adev->pio_mode); mode &= ~0x8000000; /* No FIFO in PIO */ @@ -199,7 +199,7 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) * Set up the channel for MWDMA or UDMA modes. Much the same as with * PIO, load the mode number and then set MWDMA or UDMA flag. */ - + static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); @@ -210,12 +210,12 @@ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); addr2 = 0x51 + 4 * ap->port_no; - + /* Fast interrupt prediction disable, hold off interrupt disable */ pci_read_config_byte(pdev, addr2, &fast); fast &= ~0x07; pci_write_config_byte(pdev, addr2, fast); - + pci_read_config_dword(pdev, addr1, ®); mode = hpt3x2n_find_mode(ap, adev->dma_mode); mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ @@ -230,14 +230,14 @@ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) * * Clean up after the HPT3x2n and later DMA engine */ - + static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc) { struct ata_port *ap = qc->ap; struct pci_dev *pdev = to_pci_dev(ap->host->dev); int mscreg = 0x50 + 2 * ap->port_no; u8 bwsr_stat, msc_stat; - + pci_read_config_byte(pdev, 0x6A, &bwsr_stat); pci_read_config_byte(pdev, mscreg, &msc_stat); if (bwsr_stat & (1 << ap->port_no)) @@ -257,29 +257,29 @@ static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc) * - writing * - second channel UDMA7 (SATA ports) or higher * - 66MHz PCI - * + * * or we will underclock the device and get reduced performance. */ - + static void hpt3x2n_set_clock(struct ata_port *ap, int source) { unsigned long bmdma = ap->ioaddr.bmdma_addr; - + /* Tristate the bus */ outb(0x80, bmdma+0x73); outb(0x80, bmdma+0x77); - + /* Switch clock and reset channels */ outb(source, bmdma+0x7B); outb(0xC0, bmdma+0x79); - + /* Reset state machines */ outb(0x37, bmdma+0x70); outb(0x37, bmdma+0x74); - + /* Complete reset */ outb(0x00, bmdma+0x79); - + /* Reconnect channels to bus */ outb(0x00, bmdma+0x73); outb(0x00, bmdma+0x77); @@ -291,7 +291,7 @@ static int hpt3x2n_pair_idle(struct ata_port *ap) { struct ata_host *host = ap->host; struct ata_port *pair = host->ports[ap->port_no ^ 1]; - + if (pair->hsm_task_state == HSM_ST_IDLE) return 1; return 0; @@ -305,7 +305,7 @@ static int hpt3x2n_use_dpll(struct ata_port *ap, int reading) return USE_DPLL; /* Needed for write */ if (flags & PCI66) return USE_DPLL; /* Needed at 66Mhz */ - return 0; + return 0; } static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc) @@ -313,7 +313,7 @@ static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc) struct ata_taskfile *tf = &qc->tf; struct ata_port *ap = qc->ap; int flags = (long)ap->host->private_data; - + if (hpt3x2n_pair_idle(ap)) { int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE)); if ((flags & USE_DPLL) != dpll) { @@ -347,13 +347,13 @@ static struct scsi_host_template hpt3x2n_sht = { /* * Configuration for HPT3x2n. */ - + static struct ata_port_operations hpt3x2n_port_ops = { .port_disable = ata_port_disable, .set_piomode = hpt3x2n_set_piomode, .set_dmamode = hpt3x2n_set_dmamode, .mode_filter = ata_pci_default_filter, - + .tf_load = ata_tf_load, .tf_read = ata_tf_read, .check_status = ata_check_status, @@ -381,11 +381,11 @@ static struct ata_port_operations hpt3x2n_port_ops = { .port_start = ata_port_start, .port_stop = ata_port_stop, .host_stop = ata_host_stop -}; +}; /** * hpt3xn_calibrate_dpll - Calibrate the DPLL loop - * @dev: PCI device + * @dev: PCI device * * Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this * succeeds @@ -396,7 +396,7 @@ static int hpt3xn_calibrate_dpll(struct pci_dev *dev) u8 reg5b; u32 reg5c; int tries; - + for(tries = 0; tries < 0x5000; tries++) { udelay(50); pci_read_config_byte(dev, 0x5b, ®5b); @@ -422,16 +422,16 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev) { unsigned long freq; u32 fcnt; - + pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt); if ((fcnt >> 12) != 0xABCDE) { printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n"); return 33; /* Not BIOS set */ } fcnt &= 0x1FF; - + freq = (fcnt * 77) / 192; - + /* Clamp to bands */ if (freq < 40) return 33; @@ -471,7 +471,7 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev) * * To pin down HPT371N */ - + static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) { /* HPT372N and friends - UDMA133 */ @@ -488,14 +488,14 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) u8 irqmask; u32 class_rev; - + unsigned int pci_mhz; unsigned int f_low, f_high; int adjust; - + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); class_rev &= 0xFF; - + switch(dev->device) { case PCI_DEVICE_ID_TTI_HPT366: if (class_rev < 6) @@ -530,16 +530,16 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or 50 for UDMA100. Right now we always use 66 */ - + pci_mhz = hpt3x2n_pci_clock(dev); - + f_low = (pci_mhz * 48) / 66; /* PCI Mhz for 66Mhz DPLL */ f_high = f_low + 2; /* Tolerance */ - + pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100); /* PLL clock */ pci_write_config_byte(dev, 0x5B, 0x21); - + /* Unlike the 37x we don't try jiggling the frequency */ for(adjust = 0; adjust < 8; adjust++) { if (hpt3xn_calibrate_dpll(dev)) @@ -554,7 +554,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) port->private_data = NULL; if (pci_mhz > 60) port->private_data = (void *)PCI66; - + /* Now kick off ATA set up */ port_info[0] = port_info[1] = port; return ata_pci_init_one(dev, port_info, 2); -- cgit v1.2.3