Age | Commit message (Collapse) | Author | Files | Lines |
|
Add suspend support for M-Audio cards based on ICE1712 chip.
Tested with M-Audio Audiophile 24/96. S/PDIF will probably not work.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add suspend/resume support for ICE1712 chip.
Card-specific subdrivers need to enable it and provide callbacks that suspend/resume the codecs.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
The `lspci -nnvv` output contains (wrapped for line length):
00:1b.0 Audio device [0403]:
Intel Corporation 7 Series/C210 Series Chipset Family
High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:115d]
Signed-off-by: W. Trevor King <wking@tremily.us>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This used to be a part of a condition until f3d145aac913 ('ALSA: asihpi:
MMAP for non-busmaster cards') but now it's not and we can remove an
indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When we plug a 3-ring headset on the Dell machines (VID: 0x10ec0255,
SID: 0x10280632; VID: 0x10ec0293, SID: 0x1028062c; VID: 0x10ec0293,
SID: 0x1028062e), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The auto-parser may ignore some pins that could be valid when they
don't match with the assumption or if there are way too many pins
assigned to the same output type. So far, such a pin has been
silently ignored, but it's better to leave a message, which would help
for debugging and understanding the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a temporary fix for some Intel HDMI codecs to avoid no sound output for
a resuming playback after S3.
After S3, the audio driver restores pin:cvt connection selections by
snd_hda_codec_resume_cache(). However this can happen before the gfx side is
ready and such connect selection is overlooked by HW. After gfx is ready, the
pins make the default selection again. And this will cause multiple pins share
a same convertor and mute control will affect each other. Thus a resumed audio
playback become silent after S3.
This patch verifies pin:cvt connection on preparing a stream, to assure the pin
selects the right convetor and an assigned convertor is not shared by other
unused pins. Apply this fix-up on Haswell, Broadwell and Valleyview (Baytrail).
We need this temporary fix before a reliable software communication channel is
established between audio and gfx, to sync audio/gfx operations.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The code introduced in commit 1f91ecc14dee ("ALSA: oxygen: modify
adjust_dg_dac_routing function") accidentally disregarded the old value
of the playback routing register, so it broke the "Stereo Upmixing"
mixer control.
The unmuted parts of the channel routing are the same for all settings
of the output destination, so it suffices to revert that part of the
patch.
Fixes: 1f91ecc14dee ('ALSA: oxygen: modify adjust_dg_dac_routing function')
Tested-by: Roman Volkov <v1ron@mail.ru>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
When the power state of ALC283 codec goes to D3 or return back to D0,
it gives a noise via headphone output. To follow the depop procedure,
it will be better.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71861
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
|
|
Kconfig symbol X86_32 was introduced in October 2005, it's about time
to use it :-)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CS5536 companion chipset is not only used on 32-bit x86 systems as
I originally thought, it is also used on MIPS Loongson/Lemote 2
systems. So let the snd-cs5535audio driver be built on MIPS too.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch initialized the local audio InfoFrame variable 'ai' to be all zero,
thus the data bytes will indicate "Refer to Stream Header" by default.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CS5530, CS5535 and CS5536 chipsets are companions of the Geode
series of processors, which are 32-bit x86 processors. So the
snd-cs5530 and snd-cs5535audio drivers are only needed on this
architecture, except for build testing purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Lenovo IdeaPad 410Y with ALC282 codec makes loud click noises at boot
and shutdown. Also, it wrongly misdetects the acpi_thinkpad hook.
This patch adds a device-specific fixup for disabling the shutup
callback that is the cause of the click noise and also avoiding the
thinpad_helper calls.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71511
Reported-and-tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The previous dev_err() conversion resulted in a code that may give
NULL dereference in snd_emu10k1_ptr_write(). Since it's a sanity
check, better to be replaced with a debug macro like other places in
this driver.
Fixes: 6f002b02166c ('ALSA: emu10k1: Use standard printk helpers')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are some places where we dereference "chip" in the error message
but we've already freed it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
"chip" is NULL here. We don't need a printk here because kmalloc() has
it built in.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For making the driver behavior compatible with the earlier kernels,
use the analog beep in the loopback path instead of the digital beep.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The mixer widget (NID 0x20) of AD1884 and AD1984 codecs isn't
connected directly to the actual I/O paths but only via another mixer
widget (NID 0x21). We need a similar fix as we did for AD1882.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When plugging a headphone or headset, lots of noise is heard from
internal speaker, after changing the automute via amp instead of
pinctl, the noise disappears.
BugLink: https://bugs.launchpad.net/bugs/1268468
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This quirk is needed for the headset microphone to work.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Marius Knaust <marius.knaust@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The ops to read and write registers should take pointers labeled as
__iomem. Thanks to the sparse bot for catching this.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Using readl, writel, etc. resulted in some architectures, such as
s390, expanding the member names into zpci_writel. Obviously not the
intended result.
Fixes s390 build breakage introduced by "4083081 - ALSA: hda - Allow
different ops to read/write registers"
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It is only used in hda_controller.c now.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove the dependency on CONFIG_PCI for building hda codec drivers so
that platforms with HDA attach via means other than PCI can use them.
This was as suggested by tiwai.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Codec creation and stream initialization can be shared between
hda_intel and hda platform drivers. Move it and the static functions
it depends on to hda_controller.c.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This code will be reused by an hda_platform driver as it has no PCI
dependencies. This allows update_rirb to be static as all users are
now in hda_controller.c.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This op will be used by hda_intel to do the position check. Takashi
wisely suggested adding this before moving the interrupt handler to
common HDA code. Having this callback prevents the need to move the
hda_intel specific delayed interrupt handling with the irq.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Share more code from hda_intel. This moves the link control and
initialization to hda_controller. The code will also be used by an
hda platform driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Combining the call to alloc_cmd_io with the allocate pages function
removes an extra interface between hda_intel and hda_controller.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is done to allow an HDA platform driver to reuse the code.
A few of the interfaces added to hda_controller will disappear in
following commits as their users are also moved to hda_controller.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Moving the DSP loading functionality to hda_controller.c means that
the dsp lock doesn't need to be shared in hda_intel and
hda_controller. The forthcoming platform driver doesn't need the DSP
loading code, but sharing it doesn't hurt.
Tested on Chromebook Pixel's ca0132 that uses the DSP loader.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull allocation from first_init to a new function in hda_controller.c.
Short term this will allow the dsp loader to be moved as well. In
later commits it will allow the same allocation to be used by the
platform hda driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull the pcm_ops and the functions they use into a new hda_controller
file. This is done to allow for other hda implementations besides PCI
to use the same ops. The hda_controller file will house functionality
related to HDA but independent of the bus used to talk to the
controller.
This currently shares dsp locking across the two files. This will be
remedied in a following commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Adding this op allows the X86 specific mmap operation to help in
hda_intel without needing a CONFIG_X86 in future non-PCI hda drivers.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Break out the allocation of pages for DMA and PCM buffers to ops in
the chip structure. This is done to allow for architecture specific
work-arounds to be added. Currently mark_pages_wc is used by
hda_intel. This avoids needing to move that x86-specific code to a
common area shared with hda platform drivers.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Passing the max slots and power save arguments to codec_create will
allow for its reuse by an hda_platform driver. It makes the function
independent of the module params in hda_intel and ready to move to
hda_shared in a following commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Keeping a pointer to the jackpoll_ms array in the chip will allow
azx_codec_create to be shared between hda_intel and hda_platform
drivers. Also modify get_jackpoll_ms to make the jackpoll_ms member
optional, this way a platform driver can leave it out if it's not
needed.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Although the code was updated last year the "#if 0" surrounding it
dates back to the original git commit. The function will be moved to
a new file, no need to carry the dead code.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a PCI-only feature, but adding a callback for it in the chip
structure breaks the PCI dependency in the RIRB code allowing the
logic there to be re-used by the platform HDA driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This removes calls to get the device via PCI from other parts of the
code that will be able to be re-used by the platform driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This will allow for a platform hda driver to use it as well. It
removes the dependency on the module param from hda_intel, which will
allow for azx_setup_periods to be shared.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The forthcoming platform hda driver needs to override the way
registers are read and written. In preparation for that, introduce a
reg_ops struct that can be implemented differently by the new driver.
Change the existing macros to use the new structure, and move them to
hda_priv.h where they will be accessible to both PCI and platform
drivers.
Start with register access, but later commits will add more ops that
differ between PCI and platform.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|