summaryrefslogtreecommitdiff
path: root/drivers/mtd/nand
AgeCommit message (Collapse)AuthorFilesLines
2009-04-06Merge git://git.infradead.org/mtd-2.6Linus Torvalds13-55/+1695
* git://git.infradead.org/mtd-2.6: (53 commits) [MTD] struct device - replace bus_id with dev_name(), dev_set_name() [MTD] [NOR] Fixup for Numonyx M29W128 chips [MTD] mtdpart: Make ecc_stats more realistic. powerpc/85xx: TQM8548: Update DTS file for multi-chip support powerpc: NAND: FSL UPM: document new bindings [MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays [MTD] [NAND] FSL-UPM: add multi chip support [MTD] [NOR] Add device parent info to physmap_of [MTD] [NAND] Add support for NAND on the Socrates board [MTD] [NAND] Add support for 4KiB pages. [MTD] sysfs support should not depend on CONFIG_PROC_FS [MTD] [NAND] Add parent info for CAFÉ controller [MTD] support driver model updates [MTD] driver model updates (part 2) [MTD] driver model updates [MTD] [NAND] move gen_nand's probe function to .devinit.text [MTD] [MAPS] move sa1100 flash's probe function to .devinit.text [MTD] fix use after free in register_mtd_blktrans [MTD] [MAPS] Drop now unused sharpsl-flash map [MTD] ofpart: Check name property to determine partition nodes. ... Manually fix trivial conflict in drivers/mtd/maps/Makefile
2009-04-06[MTD] struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers1-1/+1
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-06[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delaysWolfgang Grandegger1-2/+18
The NAND flash on the TQM8548_BE modules requires a short delay after running the UPM pattern. The TQM8548_BE requires a further short delay after writing out a buffer. Normally the R/B pin should be checked, but it's not connected on the TQM8548_BE. The existing driver uses similar fixed delay points. To manage these extra delays in a more general way, I introduced the "fsl,ump-wait-flags" property allowing the board- specific driver to specify various types of extra delay. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-06[MTD] [NAND] FSL-UPM: add multi chip supportWolfgang Grandegger1-23/+76
This patch adds support for multi-chip NAND devices to the FSL-UPM driver. This requires support for multiple GPIOs for the RNB pins. The NAND chips are selected through address lines defined by the FDT property "fsl,upm-addr-line-cs-offsets". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-06[MTD] [NAND] Add support for NAND on the Socrates boardWolfgang Grandegger3-0/+332
Signed-off-by: Ilya Yanok <yanok@emcraft.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-06[MTD] [NAND] Add support for 4KiB pages.Thomas Gleixner1-0/+18
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-05Merge ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param * git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param: module: use strstarts() strstarts: helper function for !strncmp(str, prefix, strlen(prefix)) arm: allow usage of string functions in linux/string.h module: don't use stop_machine on module load module: create a request_module_nowait() module: include other structures in module version check module: remove the SHF_ALLOC flag on the __versions section. module: clarify the force-loading taint message. module: Export symbols needed for Ksplice Ksplice: Add functions for walking kallsyms symbols module: remove module_text_address() module: __module_address module: Make find_symbol return a struct kernel_symbol kernel/module.c: fix an unused goto label param: fix charp parameters set via sysfs Fix trivial conflicts in kernel/extable.c manually.
2009-04-04[MTD] [NAND] Add parent info for CAFÉ controllerDavid Woodhouse1-0/+1
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-04[MTD] support driver model updatesDavid Brownell2-0/+3
Follow-on patch to the previous driver model patch for the MTD framework. This one makes various MTD drivers connect to the driver model tree, so /sys/devices/virtual/mtd/* nodes are no longer present ... mostly drivers used on boards I have handy. Based on a patch from Kay Sievers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-03[MTD] [NAND] move gen_nand's probe function to .devinit.textUwe Kleine-König1-1/+1
A pointer to plat_nand_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Hamish Moffatt <hamish@cloud.net.au> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Vitaly Wool <vitalywool@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-31module: remove module_text_address()Rusty Russell1-2/+2
Impact: Replace and remove risky (non-EXPORTed) API module_text_address() returns a pointer to the module, which given locking improvements in module.c, is useless except to test for NULL: 1) If the module can't go away, use __module_text_address. 2) Otherwise, just use is_module_text_address(). Cc: linux-mtd@lists.infradead.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2009-03-30trivial: MTD: remove EOL from MODULE_DESCRIPTIONNiels de Vos1-1/+1
There is no need to have a "\n" on a MODULE_DESCRIPTION, remove it. Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-03-28Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds3-4/+2
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits) [ARM] 5435/1: fix compile warning in sanity_check_meminfo() [ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx [ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0 [ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins imxfb: Fix TFT mode i.MX21/27: remove ifdef CONFIG_FB_IMX imxfb: add clock support mxc: add arch_reset() function clkdev: add possibility to get a clock based on the device name i.MX1: remove fb support from mach-imx [ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined Gemini: Add support for Teltonika RUT100 Gemini: gpiolib based GPIO support v2 MAINTAINERS: add myself as Gemini architecture maintainer ARM: Add Gemini architecture v3 [ARM] OMAP: Fix compile for omap2_init_common_hw() MAINTAINERS: Add myself as Faraday ARM core variant maintainer ARM: Add support for FA526 v2 [ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h [ARM] collie: fix two minor formatting nits ...
2009-03-28Merge branch 'origin' into develRussell King2-13/+14
Conflicts: sound/soc/pxa/pxa2xx-i2s.c
2009-03-27Merge branch 'core/percpu' into percpu-cpumask-x86-for-linus-2Ingo Molnar1-1/+1
Conflicts: arch/parisc/kernel/irq.c arch/x86/include/asm/fixmap_64.h arch/x86/include/asm/setup.h kernel/irq/handle.c Semantic merge: arch/x86/include/asm/fixmap.h Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-24platform driver: fix incorrect use of 'platform_bus_type' with 'struct ↵Ming Lei1-12/+13
device_driver' This patch fixes the bug reported in http://bugzilla.kernel.org/show_bug.cgi?id=11681. "Lots of device drivers register a 'struct device_driver' with the '.bus' member set to '&platform_bus_type'. This is wrong, since the platform_bus functions expect the 'struct device_driver' to be wrapped up in a 'struct platform_driver' which provides some additional callbacks (like suspend_late, resume_early). The effect may be that platform_suspend_late() uses bogus data outside the device_driver struct as a pointer pointer to the device driver's suspend_late() function or other hard to reproduce failures."(Lothar Wassmann) Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24mtd: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers1-1/+1
Cc: dwmw2@infradead.org Cc: linux-mtd@lists.infradead.org Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
2009-03-24[MTD] [NAND] sh_flctl: fix hardware ecc handling for 2048 byte pageYoshihiro Shimoda1-6/+12
Signed-off-by: Jeremy Baker <Jeremy.Baker@renesas.com> Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] pxa3xx_nand: add ability to keep controller settings defined by ↵Mike Rapoport1-1/+102
OBM/bootloader Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] pxa3xx_nand: allow building as moduleMike Rapoport2-1/+11
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] pxa3xx_nand: use resource_size instead of 'r->end - r->start + 1'Mike Rapoport1-3/+3
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] TXx9 SoC NAND Flash Memory Controller driverAtsushi Nemoto3-0/+435
This patch adds support for the integrated NAND flash controller of the TXx9 family. Once upon a time there were tx4925ndfmc and tx4938ndfmc driver. They were removed due to bitrot in 2005. This new driver is completely rewritten based on a driver in CELF patch archive. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Ralf Bächle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] partitioning utility predicatesDavid Brownell1-13/+0
Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a DaVinci-specific driver to the <linux/mtd/partitions.h> header. Use those to eliminate #ifdefs in two drivers which had their own definitions of mtd_has_partitions(). Quite a lot of other MTD drivers could benefit from using use one or both of these to remove #ifdeffery. Maybe some Janitors would like to help. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] davinci: drop usage of cpu_is_* macroKevin Hilman1-3/+0
Usage of davinci-specific cpu_is macros is not allowed in drivers. These options should be passed in through platform_data. Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] fix broken debug messagesDavid Brownell1-4/+4
Fix incorrect debug messages (*write* not read); someone committed some cut'n'paste bugs.  There might be more, I only noticed these since I was looking for nand_read usage and landed in some very wrong functions. IMO all MTD debugging message framework is goofed, anyway. It uses "DEBUG" in a way that's incompatible with usage most everywhere else in the kernel, and which prevents normal pr_dbg() and dev_dbg() calls from working right. [True. It predates those by a long way, and should probably be updated to use them. dwmw2] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] davinci_nand driverDavid Brownell3-0/+592
This is a device driver for the NAND flash controller found on the various DaVinci family chips. It handles up to four SoC chipselects, and some flavors of secondary chipselect (e.g. based on upper bits of the address bus) as used with some multichip packages. (Including the 2 GiB chips used on some TI devel boards.) The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as available on chips like the DM355 or OMAP-L137 and needed with the more error-prone MLC NAND chips. This is a cleaned-up version of code that's been in use for several years now; sanity checked with the new drivers/mtd/tests. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] fix "raw" reads with ECC syndrome layoutsDavid Brownell1-4/+95
The syndrome based page read/write routines store ECC, and possibly other "OOB" data, right after each chunk of ECC'd data. With ECC chunk size of 512 bytes and a large page (2KiB) NAND, the layout is: data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines use a traditional layout -- data OOB, disregarding the prepad and postpad values -- so when they're used with that type of ECC hardware, those calls mix up the data and OOB. Which means, in particular, that bad block tables won't be found on startup, with data corruption and related chaos ensuing. The current syndrome-based drivers in mainline all seem to use one chunk per page; presumably they haven't noticed such bugs. Fix this, by adding read/write page_raw_syndrome() routines as siblings of the existing non-raw routines; "raw" just means to bypass the ECC computations, not change data and OOB layout. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] Blackfin NFC Driver: drop pointless casts with set_dma_callback()Mike Frysinger1-1/+1
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] Blackfin NFC Driver: mark bf5xx_nand_add_partition() as __devinitMike Frysinger1-1/+1
The bf5xx_nand_add_partition() func is only called by __devinit functions, so put it into the __devinit section as well Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] Blackfin NFC Driver: do not clobber DMAC1_PERIMUXMike Frysinger1-8/+6
Only set DMAC1_PERIMUX once we have requested and been granted the dma channel to prevent breaking other peripherals in the error case Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-13Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into develRussell King3-3/+4
Conflicts: arch/arm/mach-at91/gpio.c
2009-03-13[ARM] MXC: remove _clk suffix from clock namesSascha Hauer1-1/+1
The context makes it clear already that these are clocks, so there's no need for such a suffix. This patch only changes the clocks actually used in the tree. The remaining clocks are renamed in the subsequent architecture specific patches. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-09[ARM] pxa: move pxa2xx chip selects definitions out of pxa-regs.hEric Miao1-2/+1
The definitions of PXA_CS<x>_PHYS are really PXA2xx specific and should be moved out of pxa-regs.h. As an illustration, the PXA3xx static chip selects definitions are added into pxa3xx-regs.h. Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-03-09[ARM] pxa: move DMA registers definitions into <mach/dma.h>Eric Miao1-1/+0
1. Driver code where pxa_request_dma() is called will most likely reference DMA registers as well, and it is really unnecessary to include pxa-regs.h just for this. Move the definitions into <mach/dma.h> and make relevant drivers include it instead of <mach/pxa-regs.h>. 2. Introduce DMAC_REGS_VIRT as the virtual address base for these DMA registers. This allows later processors to re-use the same IP while registers may start at different I/O address. Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-03-03[ARM] fix lots of ARM __devexit sillynessRussell King1-1/+1
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-22Merge branch 'linus' into x86/apicIngo Molnar1-1/+2
Conflicts: arch/x86/mach-default/setup.c Semantic conflict resolution: arch/x86/kernel/setup.c Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-02-16[ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device ↵Gregory CLEMENT1-1/+2
controller Add support for inverted rdy_busy pin for Atmel nand device controller It will fix building error on NeoCore926 board. Acked-by: Andrew Victor <linux@maxim.org.za> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-01-30x86: allow more than 8 cpus to be used on 32-bitYinghai Lu1-1/+1
X86_PC is the only remaining 'sub' architecture, so we dont need it anymore. This also cleans up a few spurious references to X86_PC in the driver space - those certainly should be X86. Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-01-29x86: rename X86_GENERICARCH to X86_32_NON_STANDARDIngo Molnar1-1/+1
X86_GENERICARCH is a misnomer - it contains non-PC 32-bit architectures that are not included in the default build. Rename it to X86_32_NON_STANDARD. Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-01-28powerpc: More printing warning fixes for the l64 to ll64 conversionStephen Rothwell2-6/+6
These are all powerpc specific drivers. res.start in fsl_elbc_nand.c needs to be cast since it may be either 32 or 64 bit. Thanks to Scott Wood for noticing. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-09[MTD] [NAND] add cmdline parsing (mtdparts=) support to cafe_nandPhilip Rakity1-2/+5
[dwmw2: updated and made to still register whole device first] Signed-off-by: Philip Rakity <pakity@yahoo.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] ndfc driverSean MacLennan2-136/+140
The current ndfc driver only compiles under arch/ppc. This arch was removed from the kernel. I notice the event entry for the ndfc in Kconfig has been removed in 2.6.28. This patch converts the ndfc to a proper OF (OpenFirmware) driver. I can give a working example of the DTS if needed. The patch has been in production use on the PIKA Warp Appliance and is in use by others. The Warp basically boots from NAND, so the ndfc driver is very important to us. Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Acked-By: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accuratelyMatt Reimer1-1/+1
The various fields in NDTR{01} are in units of clock ticks minus one, but the ns2cycle macro mistakenly adds one, inflating the number of clock ticks and making it impossible to set any of these fields to zero. Signed-off-by: Matt Reimer <mreimer@vpop.net> Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] pxa3xx: fix non-page-aligned readsMatt Reimer1-2/+2
Reads from non-page-aligned addresses were broken because while the address to read from was correctly written to NDCB*, a full page was always read. Fix this by ignoring the column and only using the page address. I suspect this whole-page behavior is due to the controller's need to read the entire page in order to generate correct ECC. In the non-ECC case this could be optimized to use the column address, and to set the read length to what is being requested rather than the length of an entire page. Signed-off-by: Matt Reimer <mreimer@vpop.net> Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] fix nandsim sched.h referencesRandy Dunlap1-0/+1
Fix sched.h references: build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: dereferencing pointer to incomplete type build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: 'PF_MEMALLOC' undeclared (first use in this function) build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1328: error: dereferencing pointer to incomplete type build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: dereferencing pointer to incomplete type build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: 'PF_MEMALLOC' undeclared (first use in this function) build-r7149.out:make[4]: *** [drivers/mtd/nand/nandsim.o] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] alauda: use USB API functions rather than constantsJulia Lawall1-3/+3
This set of patches introduces calls to the following set of functions: usb_endpoint_dir_in(epd) usb_endpoint_dir_out(epd) usb_endpoint_is_bulk_in(epd) usb_endpoint_is_bulk_out(epd) usb_endpoint_is_int_in(epd) usb_endpoint_is_int_out(epd) usb_endpoint_num(epd) usb_endpoint_type(epd) usb_endpoint_xfer_bulk(epd) usb_endpoint_xfer_control(epd) usb_endpoint_xfer_int(epd) usb_endpoint_xfer_isoc(epd) In some cases, introducing one of these functions is not possible, and it just replaces an explicit integer value by one of the following constants: USB_ENDPOINT_XFER_BULK USB_ENDPOINT_XFER_CONTROL USB_ENDPOINT_XFER_INT USB_ENDPOINT_XFER_ISOC An extract of the semantic patch that makes these changes is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r1@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) == - \(USB_ENDPOINT_XFER_CONTROL\|0\)) + usb_endpoint_xfer_control(epd) @r5@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) == - \(USB_DIR_IN\|0x80\)) + usb_endpoint_dir_in(epd) @inc@ @@ #include <linux/usb.h> @depends on !inc && (r1||r5)@ @@ + #include <linux/usb.h> #include <linux/usb/...> // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05Merge branch 'master' of ↵David Woodhouse3-7/+7
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: arch/arm/mach-pxa/corgi.c arch/arm/mach-pxa/poodle.c arch/arm/mach-pxa/spitz.c
2008-12-23[MTD] struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers3-3/+3
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-16[ARM] MX3: add NAND supportSascha Hauer1-1/+1
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-15Merge branch 'omap3-upstream' of ↵Russell King3-3/+7
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-20 10:03:26 +0000