diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/RCU/00-INDEX | 2 | ||||
| -rw-r--r-- | Documentation/RCU/trace.txt | 413 | ||||
| -rw-r--r-- | Documentation/arm/pxa/mfp.txt | 286 | ||||
| -rw-r--r-- | Documentation/block/biodoc.txt | 6 | ||||
| -rw-r--r-- | Documentation/fb/pxafb.txt | 92 | ||||
| -rw-r--r-- | Documentation/lguest/lguest.c | 66 | ||||
| -rw-r--r-- | Documentation/lockstat.txt | 51 |
7 files changed, 836 insertions, 80 deletions
diff --git a/Documentation/RCU/00-INDEX b/Documentation/RCU/00-INDEX index 461481dfb7c3..7dc0695a8f90 100644 --- a/Documentation/RCU/00-INDEX +++ b/Documentation/RCU/00-INDEX @@ -16,6 +16,8 @@ RTFP.txt - List of RCU papers (bibliography) going back to 1980. torture.txt - RCU Torture Test Operation (CONFIG_RCU_TORTURE_TEST) +trace.txt + - CONFIG_RCU_TRACE debugfs files and formats UP.txt - RCU on Uniprocessor Systems whatisRCU.txt diff --git a/Documentation/RCU/trace.txt b/Documentation/RCU/trace.txt new file mode 100644 index 000000000000..068848240a8b --- /dev/null +++ b/Documentation/RCU/trace.txt @@ -0,0 +1,413 @@ +CONFIG_RCU_TRACE debugfs Files and Formats + + +The rcupreempt and rcutree implementations of RCU provide debugfs trace +output that summarizes counters and state. This information is useful for +debugging RCU itself, and can sometimes also help to debug abuses of RCU. +Note that the rcuclassic implementation of RCU does not provide debugfs +trace output. + +The following sections describe the debugfs files and formats for +preemptable RCU (rcupreempt) and hierarchical RCU (rcutree). + + +Preemptable RCU debugfs Files and Formats + +This implementation of RCU provides three debugfs files under the +top-level directory RCU: rcu/rcuctrs (which displays the per-CPU +counters used by preemptable RCU) rcu/rcugp (which displays grace-period +counters), and rcu/rcustats (which internal counters for debugging RCU). + +The output of "cat rcu/rcuctrs" looks as follows: + +CPU last cur F M + 0 5 -5 0 0 + 1 -1 0 0 0 + 2 0 1 0 0 + 3 0 1 0 0 + 4 0 1 0 0 + 5 0 1 0 0 + 6 0 2 0 0 + 7 0 -1 0 0 + 8 0 1 0 0 +ggp = 26226, state = waitzero + +The per-CPU fields are as follows: + +o "CPU" gives the CPU number. Offline CPUs are not displayed. + +o "last" gives the value of the counter that is being decremented + for the current grace period phase. In the example above, + the counters sum to 4, indicating that there are still four + RCU read-side critical sections still running that started + before the last counter flip. + +o "cur" gives the value of the counter that is currently being + both incremented (by rcu_read_lock()) and decremented (by + rcu_read_unlock()). In the example above, the counters sum to + 1, indicating that there is only one RCU read-side critical section + still running that started after the last counter flip. + +o "F" indicates whether RCU is waiting for this CPU to acknowledge + a counter flip. In the above example, RCU is not waiting on any, + which is consistent with the state being "waitzero" rather than + "waitack". + +o "M" indicates whether RCU is waiting for this CPU to execute a + memory barrier. In the above example, RCU is not waiting on any, + which is consistent with the state being "waitzero" rather than + "waitmb". + +o "ggp" is the global grace-period counter. + +o "state" is the RCU state, which can be one of the following: + + o "idle": there is no grace period in progress. + + o "waitack": RCU just incremented the global grace-period + counter, which has the effect of reversing the roles of + the "last" and "cur" counters above, and is waiting for + all the CPUs to acknowledge the flip. Once the flip has + been acknowledged, CPUs will no longer be incrementing + what are now the "last" counters, so that their sum will + decrease monotonically down to zero. + + o "waitzero": RCU is waiting for the sum of the "last" counters + to decrease to zero. + + o "waitmb": RCU is waiting for each CPU to execute a memory + barrier, which ensures that instructions from a given CPU's + last RCU read-side critical section cannot be reordered + with instructions following the memory-barrier instruction. + +The output of "cat rcu/rcugp" looks as follows: + +oldggp=48870 newggp=48873 + +Note that reading from this file provokes a synchronize_rcu(). The +"oldggp" value is that of "ggp" from rcu/rcuctrs above, taken before +executing the synchronize_rcu(), and the "newggp" value is also the +"ggp" value, but taken after the synchronize_rcu() command returns. + + +The output of "cat rcu/rcugp" looks as follows: + +na=1337955 nl=40 wa=1337915 wl=44 da=1337871 dl=0 dr=1337871 di=1337871 +1=50989 e1=6138 i1=49722 ie1=82 g1=49640 a1=315203 ae1=265563 a2=49640 +z1=1401244 ze1=1351605 z2=49639 m1=5661253 me1=5611614 m2=49639 + +These are counters tracking internal preemptable-RCU events, however, +some of them may be useful for debugging algorithms using RCU. In +particular, the "nl", "wl", and "dl" values track the number of RCU +callbacks in various states. The fields are as follows: + +o "na" is the total number of RCU callbacks that have been enqueued + since boot. + +o "nl" is the number of RCU callbacks waiting for the previous + grace period to end so that they can start waiting on the next + grace period. + +o "wa" is the total number of RCU callbacks that have started waiting + for a grace period since boot. "na" should be roughly equal to + "nl" plus "wa". + +o "wl" is the number of RCU callbacks currently waiting for their + grace period to end. + +o "da" is the total number of RCU callbacks whose grace periods + have completed since boot. "wa" should be roughly equal to + "wl" plus "da". + +o "dr" is the total number of RCU callbacks that have been removed + from the list of callbacks ready to invoke. "dr" should be roughly + equal to "da". + +o "di" is the total number of RCU callbacks that have been invoked + since boot. "di" should be roughly equal to "da", though some + early versions of preemptable RCU had a bug so that only the + last CPU's count of invocations was displayed, rather than the + sum of all CPU's counts. + +o "1" is the number of calls to rcu_try_flip(). This should be + roughly equal to the sum of "e1", "i1", "a1", "z1", and "m1" + described below. In other words, the number of times that + the state machine is visited should be equal to the sum of the + number of times that each state is visited plus the number of + times that the state-machine lock acquisition failed. + +o "e1" is the number of times that rcu_try_flip() was unable to + acquire the fliplock. + +o "i1" is the number of calls to rcu_try_flip_idle(). + +o "ie1" is the number of times rcu_try_flip_idle() exited early + due to the calling CPU having no work for RCU. + +o "g1" is the number of times that rcu_try_flip_idle() decided + to start a new grace period. "i1" should be roughly equal to + "ie1" plus "g1". + +o "a1" is the number of calls to rcu_try_flip_waitack(). + +o "ae1" is the number of times that rcu_try_flip_waitack() found + that at least one CPU had not yet acknowledge the new grace period + (AKA "counter flip"). + +o "a2" is the number of time rcu_try_flip_waitack() found that + all CPUs had acknowledged. "a1" should be roughly equal to + "ae1" plus "a2". (This particular output was collected on + a 128-CPU machine, hence the smaller-than-usual fraction of + calls to rcu_try_flip_waitack() finding all CPUs having already + acknowledged.) + +o "z1" is the number of calls to rcu_try_flip_waitzero(). + +o "ze1" is the number of times that rcu_try_flip_waitzero() found + that not all of the old RCU read-side critical sections had + completed. + +o "z2" is the number of times that rcu_try_flip_waitzero() finds + the sum of the counters equal to zero, in other words, that + all of the old RCU read-side critical sections had completed. + The value of "z1" should be roughly equal to "ze1" plus + "z2". + +o "m1" is the number of calls to rcu_try_flip_waitmb(). + +o "me1" is the number of times that rcu_try_flip_waitmb() finds + that at least one CPU has not yet executed a memory barrier. + +o "m2" is the number of times that rcu_try_flip_waitmb() finds that + all CPUs have executed a memory barrier. + + +Hierarchical RCU debugfs Files and Formats + +This implementation of RCU provides three debugfs files under the +top-level directory RCU: rcu/rcudata (which displays fields in struct +rcu_data), rcu/rcugp (which displays grace-period counters), and +rcu/rcuhier (which displays the struct rcu_node hierarchy). + +The output of "cat rcu/rcudata" looks as follows: + +rcu: + 0 c=4011 g=4012 pq=1 pqc=4011 qp=0 rpfq=1 rp=3c2a dt=23301/73 dn=2 df=1882 of=0 ri=2126 ql=2 b=10 + 1 c=4011 g=4012 pq=1 pqc=4011 qp=0 rpfq=3 rp=39a6 dt=78073/1 dn=2 df=1402 of=0 ri=1875 ql=46 b=10 + 2 c=4010 g=4010 pq=1 pqc=4010 qp=0 rpfq=-5 rp=1d12 dt=16646/0 dn=2 df=3140 of=0 ri=2080 ql=0 b=10 + 3 c=4012 g=4013 pq=1 pqc=4012 qp=1 rpfq=3 rp=2b50 dt=21159/1 dn=2 df=2230 of=0 ri=1923 ql=72 b=10 + 4 c=4012 g=4013 pq=1 pqc=4012 qp=1 rpfq=3 rp=1644 dt=5783/1 dn=2 df=3348 of=0 ri=2805 ql=7 b=10 + 5 c=4012 g=4013 pq=0 pqc=4011 qp=1 rpfq=3 rp=1aac dt=5879/1 dn=2 df=3140 of=0 ri=2066 ql=10 b=10 + 6 c=4012 g=4013 pq=1 pqc=4012 qp=1 rpfq=3 rp=ed8 dt=5847/1 dn=2 df=3797 of=0 ri=1266 ql=10 b=10 + 7 c=4012 g=4013 pq=1 pqc=4012 qp=1 rpfq=3 rp=1fa2 dt=6199/1 dn=2 df=2795 of=0 ri=2162 ql=28 b=10 +rcu_bh: + 0 c=-268 g=-268 pq=1 pqc=-268 qp=0 rpfq=-145 rp=21d6 dt=23301/73 dn=2 df=0 of=0 ri=0 ql=0 b=10 + 1 c=-268 g=-268 pq=1 pqc=-268 qp=1 rpfq=-170 rp=20ce dt=78073/1 dn=2 df=26 of=0 ri=5 ql=0 b=10 + 2 c=-268 g=-268 pq=1 pqc=-268 qp=1 rpfq=-83 rp=fbd dt=16646/0 dn=2 df=28 of=0 ri=4 ql=0 b=10 + 3 c=-268 g=-268 pq=1 pqc=-268 qp=0 rpfq=-105 rp=178c dt=21159/1 dn=2 df=28 of=0 ri=2 ql=0 b=10 + 4 c=-268 g=-268 pq=1 pqc=-268 qp=1 rpfq=-30 rp=b54 dt=5783/1 dn=2 df=32 of=0 ri=0 ql=0 b=10 + 5 c=-268 g=-268 pq=1 pqc=-268 qp=1 rpfq=-29 rp=df5 dt=5879/1 dn=2 df=30 of=0 ri=3 ql=0 b=10 + 6 c=-268 g=-268 pq=1 pqc=-268 qp=1 rpfq=-28 rp=788 dt=5847/1 dn=2 df=32 of=0 ri=0 ql=0 b=10 + 7 c=-268 g=-268 pq=1 pqc=-268 qp=1 rpfq=-53 rp=1098 dt=6199/1 dn=2 df=30 of=0 ri=3 ql=0 b=10 + +The first section lists the rcu_data structures for rcu, the second for +rcu_bh. Each section has one line per CPU, or eight for this 8-CPU system. +The fields are as follows: + +o The number at the beginning of each line is the CPU number. + CPUs numbers followed by an exclamation mark are offline, + but have been online at least once since boot. There will be + no output for CPUs that have never been online, which can be + a good thing in the surprisingly common case where NR_CPUS is + substantially larger than the number of actual CPUs. + +o "c" is the count of grace periods that this CPU believes have + completed. CPUs in dynticks idle mode may lag quite a ways + behind, for example, CPU 4 under "rcu" above, which has slept + through the past 25 RCU grace periods. It is not unusual to + see CPUs lagging by thousands of grace periods. + +o "g" is the count of grace periods that this CPU believes have + started. Again, CPUs in dynticks idle mode may lag behind. + If the "c" and "g" values are equal, this CPU has already + reported a quiescent state for the last RCU grace period that + it is aware of, otherwise, the CPU believes that it owes RCU a + quiescent state. + +o "pq" indicates that this CPU has passed through a quiescent state + for the current grace period. It is possible for "pq" to be + "1" and "c" different than "g", which indicates that although + the CPU has passed through a quiescent state, either (1) this + CPU has not yet reported that fact, (2) some other CPU has not + yet reported for this grace period, or (3) both. + +o "pqc" indicates which grace period the last-observed quiescent + state for this CPU corresponds to. This is important for handling + the race between CPU 0 reporting an extended dynticks-idle + quiescent state for CPU 1 and CPU 1 suddenly waking up and + reporting its own quiescent state. If CPU 1 was the last CPU + for the current grace period, then the CPU that loses this race + will attempt to incorrectly mark CPU 1 as having checked in for + the next grace period! + +o "qp" indicates that RCU still expects a quiescent state from + this CPU. + +o "rpfq" is the number of rcu_pending() calls on this CPU required + to induce this CPU to invoke force_quiescent_state(). + +o "rp" is low-order four hex digits of the count of how many times + rcu_pending() has been invoked on this CPU. + +o "dt" is the current value of the dyntick counter that is incremented + when entering or leaving dynticks idle state, either by the + scheduler or by irq. The number after the "/" is the interrupt + nesting depth when in dyntick-idle state, or one greater than + the interrupt-nesting depth otherwise. + + This field is displayed only for CONFIG_NO_HZ kernels. + +o "dn" is the current value of the dyntick counter that is incremented + when entering or leaving dynticks idle state via NMI. If both + the "dt" and "dn" values are even, then this CPU is in dynticks + idle mode and may be ignored by RCU. If either of these two + counters is odd, then RCU must be alert to the possibility of + an RCU read-side critical section running on this CPU. + + This field is displayed only for CONFIG_NO_HZ kernels. + +o "df" is the number of times that some other CPU has forced a + quiescent state on behalf of this CPU due to this CPU being in + dynticks-idle state. + + This field is displayed only for CONFIG_NO_HZ kernels. + +o "of" is the number of times that some other CPU has forced a + quiescent state on behalf of this CPU due to this CPU being + offline. In a perfect world, this might neve happen, but it + turns out that offlining and onlining a CPU can take several grace + periods, and so there is likely to be an extended period of time + when RCU believes that the CPU is online when it really is not. + Please note that erring in the other direction (RCU believing a + CPU is offline when it is really alive and kicking) is a fatal + error, so it makes sense to err conservatively. + +o "ri" is the number of times that RCU has seen fit to send a + reschedule IPI to this CPU in order to get it to report a + quiescent state. + +o "ql" is the number of RCU callbacks currently residing on + this CPU. This is the total number of callbacks, regardless + of what state they are in (new, waiting for grace period to + start, waiting for grace period to end, ready to invoke). + +o "b" is the batch limit for this CPU. If more than this number + of RCU callbacks is ready to invoke, then the remainder will + be deferred. + + +The output of "cat rcu/rcugp" looks as follows: + +rcu: completed=33062 gpnum=33063 +rcu_bh: completed=464 gpnum=464 + +Again, this output is for both "rcu" and "rcu_bh". The fields are +taken from the rcu_state structure, and are as follows: + +o "completed" is the number of grace periods that have completed. + It is comparable to the "c" field from rcu/rcudata in that a + CPU whose "c" field matches the value of "completed" is aware + that the corresponding RCU grace period has completed. + +o "gpnum" is the number of grace periods that have started. It is + comparable to the "g" field from rcu/rcudata in that a CPU + whose "g" field matches the value of "gpnum" is aware that the + corresponding RCU grace period has started. + + If these two fields are equal (as they are for "rcu_bh" above), + then there is no grace period in progress, in other words, RCU + is idle. On the other hand, if the two fields differ (as they + do for "rcu" above), then an RCU grace period is in progress. + + +The output of "cat rcu/rcuhier" looks as follows, with very long lines: + +c=6902 g=6903 s=2 jfq=3 j=72c7 nfqs=13142/nfqsng=0(13142) fqlh=6 +1/1 0:127 ^0 +3/3 0:35 ^0 0/0 36:71 ^1 0/0 72:107 ^2 0/0 108:127 ^3 +3/3f 0:5 ^0 2/3 6:11 ^1 0/0 12:17 ^2 0/0 18:23 ^3 0/0 24:29 ^4 0/0 30:35 ^5 0/0 36:41 ^0 0/0 42:47 ^1 0/0 48:53 ^2 0/0 54:59 ^3 0/0 60:65 ^4 0/0 66:71 ^5 0/0 72:77 ^0 0/0 78:83 ^1 0/0 84:89 ^2 0/0 90:95 ^3 0/0 96:101 ^4 0/0 102:107 ^5 0/0 108:113 ^0 0/0 114:119 ^1 0/0 120:125 ^2 0/0 126:127 ^3 +rcu_bh: +c=-226 g=-226 s=1 jfq=-5701 j=72c7 nfqs=88/nfqsng=0(88) fqlh=0 +0/1 0:127 ^0 +0/3 0:35 ^0 0/0 36:71 ^1 0/0 72:107 ^2 0/0 108:127 ^3 +0/3f 0:5 ^0 0/3 6:11 ^1 0/0 12:17 ^2 0/0 18:23 ^3 0/0 24:29 ^4 0/0 30:35 ^5 0/0 36:41 ^0 0/0 42:47 ^1 0/0 48:53 ^2 0/0 54:59 ^3 0/0 60:65 ^4 0/0 66:71 ^5 0/0 72:77 ^0 0/0 78:83 ^1 0/0 84:89 ^2 0/0 90:95 ^3 0/0 96:101 ^4 0/0 102:107 ^5 0/0 108:113 ^0 0/0 114:119 ^1 0/0 120:125 ^2 0/0 126:127 ^3 + +This is once again split into "rcu" and "rcu_bh" portions. The fields are +as follows: + +o "c" is exactly the same as "completed" under rcu/rcugp. + +o "g" is exactly the same as "gpnum" under rcu/rcugp. + +o "s" is the "signaled" state that drives force_quiescent_state()'s + state machine. + +o "jfq" is the number of jiffies remaining for this grace period + before force_quiescent_state() is invoked to help push things + along. Note that CPUs in dyntick-idle mode thoughout the grace + period will not report on their own, but rather must be check by + some other CPU via force_quiescent_state(). + +o "j" is the low-order four hex digits of the jiffies counter. + Yes, Paul did run into a number of problems that turned out to + be due to the jiffies counter no longer counting. Why do you ask? + +o "nfqs" is the number of calls to force_quiescent_state() since + boot. + +o "nfqsng" is the number of useless calls to force_quiescent_state(), + where there wasn't actually a grace period active. This can + happen due to races. The number in parentheses is the difference + between "nfqs" and "nfqsng", or the number of times that + force_quiescent_state() actually did some real work. + +o "fqlh" is the number of calls to force_quiescent_state() that + exited immediately (without even being counted in nfqs above) + due to contention on ->fqslock. + +o Each element of the form "1/1 0:127 ^0" represents one struct + rcu_node. Each line represents one level of the hierarchy, from + root to leaves. It is best to think of the rcu_data structures + as forming yet another level after the leaves. Note that there + might be either one, two, or three levels of rcu_node structures, + depending on the relationship between CONFIG_RCU_FANOUT and + CONFIG_NR_CPUS. + + o The numbers separated by the "/" are the qsmask followed + by the qsmaskinit. The qsmask will have one bit + set for each entity in the next lower level that + has not yet checked in for the current grace period. + The qsmaskinit will have one bit for each entity that is + currently expected to check in during each grace period. + The value of qsmaskinit is assigned to that of qsmask + at the beginning of each grace period. + + For example, for "rcu", the qsmask of the first entry + of the lowest level is 0x14, meaning that we are still + waiting for CPUs 2 and 4 to check in for the current + grace period. + + o The numbers separated by the ":" are the range of CPUs + served by this struct rcu_node. This can be helpful + in working out how the hierarchy is wired together. + + For example, the first entry at the lowest level shows + "0:5", indicating that it covers CPUs 0 through 5. + + o The number after the "^" indicates the bit in the + next higher level rcu_node structure that this + rcu_node structure corresponds to. + + For example, the first entry at the lowest level shows + "^0", indicating that it corresponds to bit zero in + the first entry at the middle level. diff --git a/Documentation/arm/pxa/mfp.txt b/Documentation/arm/pxa/mfp.txt new file mode 100644 index 000000000000..a179e5bc02c9 --- /dev/null +++ b/Documentation/arm/pxa/mfp.txt @@ -0,0 +1,286 @@ + MFP Configuration for PXA2xx/PXA3xx Processors + + Eric Miao <eric.miao@marvell.com> + +MFP stands for Multi-Function Pin, which is the pin-mux logic on PXA3xx and +later PXA series processors. This document describes the existing MFP API, +and how board/platform driver authors could make use of it. + + Basic Concept +=============== + +Unlike the GPIO alternate function settings on PXA25x and PXA27x, a new MFP +mechanism is introduced from PXA3xx to completely move the pin-mux functions +out of the GPIO controller. In addition to pin-mux configurations, the MFP +also controls the low power state, driving strength, pull-up/down and event +detection of each pin. Below is a diagram of internal connections between +the MFP logic and the remaining SoC peripherals: + + +--------+ + | |--(GPIO19)--+ + | GPIO | | + | |--(GPIO...) | + +--------+ | + | +---------+ + +--------+ +------>| | + | PWM2 |--(PWM_OUT)-------->| MFP | + +--------+ +------>| |-------> to external PAD + | +---->| | + +--------+ | | +-->| | + | SSP2 |---(TXD)----+ | | +---------+ + +--------+ | | + | | + +--------+ | | + | Keypad |--(MKOUT4)----+ | + +--------+ | + | + +--------+ | + | UART2 |---(TXD)--------+ + +--------+ + +NOTE: the external pad is named as MFP_PIN_GPIO19, it doesn't necessarily +mean it's dedicated for GPIO19, only as a hint that internally this pin +can be routed from GPIO19 of the GPIO controller. + +To better understand the change from PXA25x/PXA27x GPIO alternate function +to this new MFP mechanism, here are several key points: + + 1. GPIO controller on PXA3xx is now a dedicated controller, same as other + internal controllers like PWM, SSP and UART, with 128 internal signals + which can be routed to external through one or more MFPs (e.g. GPIO<0> + can be routed through either MFP_PIN_GPIO0 as well as MFP_PIN_GPIO0_2, + see arch/arm/mach-pxa/mach/include/mfp-pxa300.h) + + 2. Alternate function configuration is removed from this GPIO controller, + the remaining functions are pure GPIO-specific, i.e. + + - GPIO signal level control + - GPIO direction control + - GPIO level change detection + + 3. Low power state for each pin is now controlled by MFP, this means the + PGSRx registers on PXA2xx are now useless on PXA3xx + + 4. Wakeup detection is now controlled by MFP, PWER does not control the + wakeup from GPIO(s) any more, depending on the sleeping state, ADxER + (as defined in pxa3xx-regs.h) controls the wakeup from MFP + +NOTE: with such a clear separation of MFP and GPIO, by GPIO<xx> we normally +mean it is a GPIO signal, and by MFP<xxx> or pin xxx, we mean a physical +pad (or ball). + + MFP API Usage +=============== + +For board code writers, here are some guidelines: + +1. include ONE of the following header files in your <board>.c: + + - #include <mach/mfp-pxa25x.h> + - #include <mach/mfp-pxa27x.h> + - #include <mach/mfp-pxa300.h> + - #include <mach/mfp-pxa320.h> + - #include <mach/mfp-pxa930.h> + + NOTE: only one file in your <board>.c, depending on the processors used, + because pin configuration definitions may conflict in these file (i.e. + same name, different meaning and settings on different processors). E.g. + for zylonite platform, which support both PXA300/PXA310 and PXA320, two + separate files are introduced: zylonite_pxa300.c and zylonite_pxa320.c + (in addition to handle MFP configuration differences, they also handle + the other differences between the two combinations). + + NOTE: PXA300 and PXA310 are almost identical in pin configurations (with + PXA310 supporting some additional ones), thus the difference is actually + covered in a single mfp-pxa300.h. + +2. prepare an array for the initial pin configurations, e.g.: + + static unsigned long mainstone_pin_config[] __initdata = { + /* Chip Select */ + GPIO15_nCS_1, + + /* LCD - 16bpp Active TFT */ + GPIOxx_TFT_LCD_16BPP, + GPIO16_PWM0_OUT, /* Backlight */ + + /* MMC */ + GPIO32_MMC_CLK, + GPIO112_MMC_CMD, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + + ... + + /* GPIO */ + GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH, + }; + + a) once the pin configurations are passed to pxa{2xx,3xx}_mfp_config(), + and written to the actual registers, they are useless and may discard, + adding '__initdata' will help save some additional bytes here. + + b) when there is only one possible pin configurations for a component, + some simplified definitions can be used, e.g. GPIOxx_TFT_LCD_16BPP on + PXA25x and PXA27x processors + + c) if by board design, a pin can be configured to wake up the system + from low power state, it can be 'OR'ed with any of: + + WAKEUP_ON_EDGE_BOTH + WAKEUP_ON_EDGE_RISE + WAKEUP_ON_EDGE_FALL + WAKEUP_ON_LEVEL_HIGH - specifically for enabling of keypad GPIOs, + + to indicate that this pin has the capability of wake-up the system, + and on which edge(s). This, however, doesn't necessarily mean the + pin _will_ wakeup the system, it will only when set_irq_wake() is + invoked with the corresponding GPIO IRQ (GPIO_IRQ(xx) or gpio_to_irq()) + and eventually calls gpio_set_wake() for the actual register setting. + + d) although PXA3xx MFP supports edge detection on each pin, the + internal logic will only wakeup the system when those specific bits + in ADxER registers are set, which can be well mapped to the + corresponding peripheral, thus set_irq_wake() can be called with + the peripheral IRQ to enable the wakeup. + + + MFP on PXA3xx +=============== + +Every external I/O pad on PXA3xx (excluding those for special purpose) has +one MFP logic associated, and is controlled by one MFP register (MFPR). + +The MFPR has the following bit definitions (for PXA300/PXA310/PXA320): + + 31 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 + +-------------------------+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ + | RESERVED |PS|PU|PD| DRIVE |SS|SD|SO|EC|EF|ER|--| AF_SEL | + +-------------------------+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ + + Bit 3: RESERVED + Bit 4: EDGE_RISE_EN - enable detection of rising edge on this pin + Bit 5: EDGE_FALL_EN - enable detection of falling edge on this pin + Bit 6: EDGE_CLEAR - disable edge detection on this pin + Bit 7: SLEEP_OE_N - enable outputs during low power modes + Bit 8: SLEEP_DATA - output data on the pin during low power modes + Bit 9: SLEEP_SEL - selection control for low power modes signals + Bit 13: PULLDOWN_EN - enable the internal pull-down resistor on this pin + Bit 14: PULLUP_EN - enable the internal pull-up resistor on this pin + Bit 15: PULL_SEL - pull state controlled by selected alternate function + (0) or by PULL{UP,DOWN}_EN bits (1) + + Bit 0 - 2: AF_SEL - alternate function selection, 8 possibilities, from 0-7 + Bit 10-12: DRIVE - drive strength and slew rate + 0b000 - fast 1mA + 0b001 - fast 2mA + 0b002 - fast 3mA + 0b003 - fast 4mA + 0b004 - slow 6mA + 0b005 - fast 6mA + 0b006 - slow 10mA + 0b007 - fast 10mA + + MFP Design for PXA2xx/PXA3xx +============================== + +Due to the difference of pin-mux handling between PXA2xx and PXA3xx, a unified +MFP API is introduced to cover both series of processors. + +The basic idea of this design is to introduce definitions for all possible pin +configurations, these definitions are processor and platform independent, and +the actual API invoked to convert these definitions into register settings and +make them effective there-after. + + Files Involved + -------------- + + - arch/arm/mach-pxa/include/mach/mfp.h + + for + 1. Unified pin definitions - enum constants for all configurable pins + 2. processor-neutral bit definitions for a possible MFP configuration + + - arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h + + for PXA3xx specific MFPR register bit definitions and PXA3xx common pin + configurations + + - arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h + + for PXA2xx specific definitions and PXA25x/PXA27x common pin configurations + + - arch/arm/mach-pxa/include/mach/mfp-pxa25x.h + arch/arm/mach-pxa/include/mach/mfp-pxa27x.h + arch/arm/mach-pxa/include/mach/mfp-pxa300.h + arch/arm/mach-pxa/include/mach/mfp-pxa320.h + arch/arm/mach-pxa/include/mach/mfp-pxa930.h + + for processor specific definitions + + - arch/arm/mach-pxa/mfp-pxa3xx.c + - arch/arm/mach-pxa/mfp-pxa2xx.c + + for implementation of the pin configuration to take effect for the actual + processor. + + Pin Configuration + ----------------- + + The following comments are copied from mfp.h (see the actual source code + for most updated info) + + /* + * a possible MFP configuration is represented by a 32-bit integer + * + * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum) + * bit 10..12 - Alternate Function Selection + * bit 13..15 - Drive Strength + * bit 16..18 - Low Power Mode State + * bit 19..20 - Low Power Mode Edge Detection + * bit 21..22 - Run Mode Pull State + * + * to facilitate the definition, the following macros are provided + * + * MFP_CFG_DEFAULT - default MFP configuration value, with + * alternate function = 0, + * drive strength = fast 3mA (MFP_DS03X) + * low power mode = default + * edge detection = none + * + * MFP_CFG - default MFPR value with alternate function + * MFP_CFG_DRV - default MFPR value with alternate function and + * pin drive strength + * MFP_CFG_LPM - default MFPR value with alternate function and + * low power mode + * MFP_CFG_X - default MFPR value with alternate function, + * pin drive strength and low power mode + */ + + Examples of pin configurations are: + + #define GPIO94_SSP3_RXD MFP_CFG_X(GPIO94, AF1, DS08X, FLOAT) + + which reads GPIO94 can be configured as SSP3_RXD, with alternate function + selection of 1, driving strength of 0b101, and a float state in low power + modes. + + NOTE: this is the default setting of this pin being configured as SSP3_RXD + which can be modified a bit in board code, though it is not recommended to + do so, simply because this default setting is usually carefully encoded, + and is supposed to work in most cases. + + Register Settings + ----------------- + + Register settings on PXA3xx for a pin configuration is actually very + straight-forward, most bits can be converted directly into MFPR value + in a easier way. Two sets of MFPR values are calculated: the run-time + ones and the low power mode ones, to allow different settings. + + The conversion from a generic pin configuration to the actual register + settings on PXA2xx is a bit complicated: many registers are involved, + including GAFRx, GPDRx, PGSRx, PWER, PKWR, PFER and PRER. Please see + mfp-pxa2xx.c for how the conversion is made. diff --git a/Documentation/block/biodoc.txt b/Documentation/block/biodoc.txt index 4dbb8be1c991..3c5434c83daf 100644 --- a/Documentation/block/biodoc.txt +++ b/Documentation/block/biodoc.txt @@ -914,7 +914,7 @@ I/O scheduler, a.k.a. elevator, is implemented in two layers. Generic dispatch queue and specific I/O schedulers. Unless stated otherwise, elevator is used to refer to both parts and I/O scheduler to specific I/O schedulers. -Block layer implements generic dispatch queue in ll_rw_blk.c and elevator.c. +Block layer implements generic dispatch queue in block/*.c. The generic dispatch queue is responsible for properly ordering barrier requests, requeueing, handling non-fs requests and all other subtleties. @@ -926,8 +926,8 @@ be built inside the kernel. Each queue can choose different one and can also change to another one dynamically. A block layer call to the i/o scheduler follows the convention elv_xxx(). This -calls elevator_xxx_fn in the elevator switch (drivers/block/elevator.c). Oh, -xxx and xxx might not match exactly, but use your imagination. If an elevator +calls elevator_xxx_fn in the elevator switch (block/elevator.c). Oh, xxx +and xxx might not match exactly, but use your imagination. If an elevator doesn't implement a function, the switch does nothing or some minimal house keeping work. diff --git a/Documentation/fb/pxafb.txt b/Documentation/fb/pxafb.txt index db9b8500b43b..d143a0a749f9 100644 --- a/Documentation/fb/pxafb.txt +++ b/Documentation/fb/pxafb.txt @@ -5,9 +5,13 @@ The driver supports the following options, either via options=<OPTIONS> when modular or video=pxafb:<OPTIONS> when built in. For example: - modprobe pxafb options=mode:640x480-8,passive + modprobe pxafb options=vmem:2M,mode:640x480-8,passive or on the kernel command line - video=pxafb:mode:640x480-8,passive + video=pxafb:vmem:2M,mode:640x480-8,passive + +vmem: VIDEO_MEM_SIZE + Amount of video memory to allocate (can be suffixed with K or M + for kilobytes or megabytes) mode:XRESxYRES[-BPP] XRES == LCCR1_PPL + 1 @@ -52,3 +56,87 @@ outputen:POLARITY pixclockpol:POLARITY pixel clock polarity 0 => falling edge, 1 => rising edge + + +Overlay Support for PXA27x and later LCD controllers +==================================================== + + PXA27x and later processors support overlay1 and overlay2 on-top of the + base framebuffer (although under-neath the base is also possible). They + support palette and no-palette RGB formats, as well as YUV formats (only + available on overlay2). These overlays have dedicated DMA channels and + behave in a similar way as a framebuffer. + + However, there are some differences between these overlay framebuffers + and normal framebuffers, as listed below: + + 1. overlay can start at a 32-bit word aligned position within the base + framebuffer, which means they have a start (x, y). This information + is encoded into var->nonstd (no, var->xoffset and var->yoffset are + not for such purpose). + + 2. overlay framebuffer is allocated dynamically according to specified + 'struct fb_var_screeninfo', the amount is decided by: + + var->xres_virtual * var->yres_virtual * bpp + + bpp = 16 -- for RGB565 or RGBT555 + = 24 -- for YUV444 packed + = 24 -- for YUV444 planar + = 16 -- for YUV422 planar (1 pixel = 1 Y + 1/2 Cb + 1/2 Cr) + = 12 -- for YUV420 planar (1 pixel = 1 Y + 1/4 Cb + 1/4 Cr) + + NOTE: + + a. overlay does not support panning in x-direction, thus + var->xres_virtual will always be equal to var->xres + + b. line length of overlay(s) must be on a 32-bit word boundary, + for YUV planar modes, it is a requirement for the component + with minimum bits per pixel, e.g. for YUV420, Cr component + for one pixel is actually 2-bits, it means the line length + should be a multiple of 16-pixels + + c. starting horizontal position (XPOS) should start on a 32-bit + word boundary, otherwise the fb_check_var() will just fail. + + d. the rectangle of the overlay should be within the base plane, + otherwise fail + + Applications should follow the sequence below to operate an overlay + framebuffer: + + a. open("/dev/fb[1-2]", ...) + b. ioctl(fd, FBIOGET_VSCREENINFO, ...) + c. modify 'var' with desired parameters: + 1) var->xres and var->yres + 2) larger var->yres_virtual if more memory is required, + usually for double-buffering + 3) var->nonstd for starting (x, y) and color format + 4) var->{red, green, blue, transp} if RGB mode is to be used + d. ioctl(fd, FBIOPUT_VSCREENINFO, ...) + e. ioctl(fd, FBIOGET_FSCREENINFO, ...) + f. mmap + g. ... + + 3. for YUV planar formats, these are actually not supported within the + framebuffer framework, application has to take care of the offsets + and lengths of each component within the framebuffer. + + 4. var->nonstd is used to pass starting (x, y) position and color format, + the detailed bit fields are shown below: + + 31 23 20 10 0 + +-----------------+---+----------+----------+ + | ... unused ... |FOR| XPOS | YPOS | + +-----------------+---+----------+----------+ + + FOR - color format, as defined by OVERLAY_FORMAT_* in pxafb.h + 0 - RGB + 1 - YUV444 PACKED + 2 - YUV444 PLANAR + 3 - YUV422 PLANAR + 4 - YUR420 PLANAR + + XPOS - starting horizontal position + YPOS - starting vertical position diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index 804520633fcf..f2dbbf3bdeab 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -481,51 +481,6 @@ static unsigned long load_initrd(const char *name, unsigned long mem) /* We return the initrd size. */ return len; } - -/* Once we know how much memory we have we can construct simple linear page - * tables which set virtual == physical which will get the Guest far enough - * into the boot to create its own. - * - * We lay them out of the way, just below the initrd (which is why we need to - * know its size here). */ -static unsigned long setup_pagetables(unsigned long mem, - unsigned long initrd_size) -{ - unsigned long *pgdir, *linear; - unsigned int mapped_pages, i, linear_pages; - unsigned int ptes_per_page = getpagesize()/sizeof(void *); - - mapped_pages = mem/getpagesize(); - - /* Each PTE page can map ptes_per_page pages: how many do we need? */ - linear_pages = (mapped_pages + ptes_per_page-1)/ptes_per_page; - - /* We put the toplevel page directory page at the top of memory. */ - pgdir = from_guest_phys(mem) - initrd_size - getpagesize(); - - /* Now we use the next linear_pages pages as pte pages */ - linear = (void *)pgdir - linear_pages*getpagesize(); - - /* Linear mapping is easy: put every page's address into the mapping in - * order. PAGE_PRESENT contains the flags Present, Writable and - * Executable. */ - for (i = 0; i < mapped_pages; i++) - linear[i] = ((i * getpagesize()) | PAGE_PRESENT); - - /* The top level points to the linear page table pages above. */ - for (i = 0; i < mapped_pages; i += ptes_per_page) { - pgdir[i/ptes_per_page] - = ((to_guest_phys(linear) + i*sizeof(void *)) - | PAGE_PRESENT); - } - - verbose("Linear mapping of %u pages in %u pte pages at %#lx\n", - mapped_pages, linear_pages, to_guest_phys(linear)); - - /* We return the top level (guest-physical) address: the kernel needs - * to know where it is. */ - return to_guest_phys(pgdir); -} /*:*/ /* Simple routine to roll all the commandline arguments together with spaces @@ -548,13 +503,13 @@ static void concat(char *dst, char *args[]) /*L:185 This is where we actually tell the kernel to initialize the Guest. We * saw the arguments it expects when we looked at initialize() in lguest_user.c: - * the base of Guest "physical" memory, the top physical page to allow, the - * top level pagetable and the entry point for the Guest. */ -static int tell_kernel(unsigned long pgdir, unsigned long start) + * the base of Guest "physical" memory, the top physical page to allow and the + * entry point for the Guest. */ +static int tell_kernel(unsigned long start) { unsigned long args[] = { LHREQ_INITIALIZE, (unsigned long)guest_base, - guest_limit / getpagesize(), pgdir, start }; + guest_limit / getpagesize(), start }; int fd; verbose("Guest: %p - %p (%#lx)\n", @@ -1030,7 +985,7 @@ static void update_device_status(struct device *dev) /* Zero out the virtqueues. */ for (vq = dev->vq; vq; vq = vq->next) { memset(vq->vring.desc, 0, - vring_size(vq->config.num, getpagesize())); + vring_size(vq->config.num, LGUEST_VRING_ALIGN)); lg_last_avail(vq) = 0; } } else if (dev->desc->status & VIRTIO_CONFIG_S_FAILED) { @@ -1211,7 +1166,7 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, void *p; /* First we need some memory for this virtqueue. */ - pages = (vring_size(num_descs, getpagesize()) + getpagesize() - 1) + pages = (vring_size(num_descs, LGUEST_VRING_ALIGN) + getpagesize() - 1) / getpagesize(); p = get_pages(pages); @@ -1228,7 +1183,7 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, vq->config.pfn = to_guest_phys(p) / getpagesize(); /* Initialize the vring. */ - vring_init(&vq->vring, num_descs, p, getpagesize()); + vring_init(&vq->vring, num_descs, p, LGUEST_VRING_ALIGN); /* Append virtqueue to this device's descriptor. We use * device_config() to get the end of the device's current virtqueues; @@ -1941,7 +1896,7 @@ int main(int argc, char *argv[]) { /* Memory, top-level pagetable, code startpoint and size of the * (optional) initrd. */ - unsigned long mem = 0, pgdir, start, initrd_size = 0; + unsigned long mem = 0, start, initrd_size = 0; /* Two temporaries and the /dev/lguest file descriptor. */ int i, c, lguest_fd; /* The boot information for the Guest. */ @@ -2040,9 +1995,6 @@ int main(int argc, char *argv[]) boot->hdr.type_of_loader = 0xFF; } - /* Set up the initial linear pagetables, starting below the initrd. */ - pgdir = setup_pagetables(mem, initrd_size); - /* The Linux boot header contains an "E820" memory map: ours is a * simple, single region. */ boot->e820_entries = 1; @@ -2064,7 +2016,7 @@ int main(int argc, char *argv[]) /* We tell the kernel to initialize the Guest: this returns the open * /dev/lguest file descriptor. */ - lguest_fd = tell_kernel(pgdir, start); + lguest_fd = tell_kernel(start); /* We clone off a thread, which wakes the Launcher whenever one of the * input file descriptors needs attention. We call this the Waker, and diff --git a/Documentation/lockstat.txt b/Documentation/lockstat.txt index 4ba4664ce5c3..9cb9138f7a79 100644 --- a/Documentation/lockstat.txt +++ b/Documentation/lockstat.txt @@ -71,35 +71,50 @@ Look at the current lock statistics: # less /proc/lock_stat -01 lock_stat version 0.2 +01 lock_stat version 0.3 02 ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 03 class name con-bounces contentions waittime-min waittime-max waittime-total acq-bounces acquisitions holdtime-min holdtime-max holdtime-total 04 ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 -06 &inode->i_data.tree_lock-W: 15 21657 0.18 1093295.30 11547131054.85 58 10415 0.16 87.51 6387.60 -07 &inode->i_data.tree_lock-R: 0 0 0.00 0.00 0.00 23302 231198 0.25 8.45 98023.38 -08 -------------------------- -09 &inode->i_data.tree_lock 0 [<ffffffff8027c08f>] add_to_page_cache+0x5f/0x190 -10 -11 ............................................................................................................................................................................................... -12 -13 dcache_lock: 1037 1161 0.38 45.32 774.51 6611 243371 0.15 306.48 77387.24 -14 ----------- -15 dcache_lock 180 [<ffffffff802c0d7e>] sys_getcwd+0x11e/0x230 -16 dcache_lock 165 [<ffffffff802c002a>] d_alloc+0x15a/0x210 -17 dcache_lock 33 [<ffffffff8035818d>] _atomic_dec_and_lock+0x4d/0x70 -18 dcache_lock 1 [<ffffffff802beef8>] shrink_dcache_parent+0x18/0x130 +06 &mm->mmap_sem-W: 233 538 18446744073708 22924.27 607243.51 1342 45806 1.71 8595.89 1180582.34 +07 &mm->mmap_sem-R: 205 587 18446744073708 28403.36 731975.00 1940 412426 0.58 187825.45 6307502.88 +08 --------------- +09 &mm->mmap_sem 487 [<ffffffff8053491f>] do_page_fault+0x466/0x928 +10 &mm->mmap_sem 179 [<ffffffff802a6200>] sys_mprotect+0xcd/0x21d +11 &mm->mmap_sem 279 [<ffffffff80210a57>] sys_mmap+0x75/0xce +12 &mm->mmap_sem 76 [<ffffffff802a490b>] sys_munmap+0x32/0x59 +13 --------------- +14 &mm->mmap_sem 270 [<ffffffff80210a57>] sys_mmap+0x75/0xce +15 &mm->mmap_sem 431 [<ffffffff8053491f>] do_page_fault+0x466/0x928 +16 &mm->mmap_sem 138 [<ffffffff802a490b>] sys_munmap+0x32/0x59 +17 &mm->mmap_sem 145 [<ffffffff802a6200>] sys_mprotect+0xcd/0x21d +18 +19 ............................................................................................................................................................................................... +20 +21 dcache_lock: 621 623 0.52 118.26 1053.02 6745 91930 0.29 316.29 118423.41 +22 ----------- +23 dcache_lock 179 [<ffffffff80378274>] _atomic_dec_and_lock+0x34/0x54 +24 dcache_lock 113 [<ffffffff802cc17b>] d_alloc+0x19a/0x1eb +25 dcache_lock 99 [<ffffffff802ca0dc>] d_rehash+0x1b/0x44 +26 dcache_lock 104 [<ffffffff802cbca0>] d_instantiate+0x36/0x8a +27 ----------- +28 dcache_lock 192 [<ffffffff80378274>] _atomic_dec_and_lock+0x34/0x54 +29 dcache_lock 98 [<ffffffff802ca0dc>] d_rehash+0x1b/0x44 +30 dcache_lock 72 [<ffffffff802cc17b>] d_alloc+0x19a/0x1eb +31 dcache_lock 112 [<ffffffff802cbca0>] d_instantiate+0x36/0x8a This excerpt shows the first two lock class statistics. Line 01 shows the output version - each time the format changes this will be updated. Line 02-04 -show the header with column descriptions. Lines 05-10 and 13-18 show the actual +show the header with column descriptions. Lines 05-18 and 20-31 show the actual statistics. These statistics come in two parts; the actual stats separated by a -short separator (line 08, 14) from the contention points. +short separator (line 08, 13) from the contention points. -The first lock (05-10) is a read/write lock, and shows two lines above the +The first lock (05-18) is a read/write lock, and shows two lines above the short separator. The contention points don't match the column descriptors, -they have two: contentions and [<IP>] symbol. +they have two: contentions and [<IP>] symbol. The second set of contention +points are the points we're contending with. +The integer part of the time values is in us. View the top contending locks: |