| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some transports (iSCSI/iSER/SRP/FC) support hardware INSERT/STRIP
capabilities while other transports like loopback/vhost-scsi need
perform this is software.
This patch allows fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC
to signal the early LUN scan handling case where PROTECT CDB bits
are set, but no fabric buffer has been provided.
For transports which use generic new command these buffers have yet
to be allocated.
Also this way, target may support protection information
against legacy initiators (writes are inserted and reads
are stripped).
(Only set prot_pto for loopback during early special case - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
No need to actually compute protection information when formatting
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
SBC-3 mandates the protection checks that must be
performed in the rdprotect/wrprotect field. Use them.
According to backstore device pi_attributes and
cdb rdprotect/wrprotect field.
(Fix incorrect se_cmd->prot_type -> TARGET_PROT_NORMAL
comparision in transport_generic_new_cmd - nab)
(Fix missing break in sbc_set_prot_op_checks - DanC + Sagi)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In case protection information is involved, allocate
protection SG-list for transport.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Building target_core_alua.o triggers a GCC warning:
drivers/target/target_core_alua.c: In function ‘target_alua_state_check’:
drivers/target/target_core_alua.c:773:18: warning: ‘alua_ascq’ may be used uninitialized in this function [-Wmaybe-uninitialized]
cmd->scsi_ascq = alua_ascq;
^
This is a false positive. A little trial and error shows it is
apparently caused by core_alua_state_lba_dependent(). It must be hard
for GCC to track the branches of a switch statement, inside a
list_for_each_entry loop, inside a while loop.
But if we add a small (inline) helper function we can reorganize the
code a bit. That also allows to drop alua_ascq which, obviously, gets
rid of this warning.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband into for-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI
regressions we have been having on some types of devices. The other
two are quirks for some Logitech video devices"
* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver tree fix from Greg KH:
"Here is a single staging driver fix for your tree.
It resolves an issue with arbritary writes to memory if a specific
driver is loaded"
* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging/cxt1e1/linux.c: Correct arbitrary memory write in c4_ioctl()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal fixes from Zhang Rui:
"Specifics:
- Update the help text of INT3403 Thermal driver, which was not
friendly to users. From Zhang Rui.
- The "type" sysfs attribute of x86_pkg_temp_thermal registered
thermal zones includes an instance number, which makes the
thermal-to-hwmon bridge fails to group them all in a single hwmon
device. Fixed by Jean Delvare.
- The hwmon device registered by x86_pkg_temp_thermal driver is
redundant because the temperature value reported by
x86_pkg_temp_thermal is already reported by the coretemp driver.
Fixed by Jean Delvare.
- Fix a problem that the cooling device can not be updated properly
if it is initialized at max cooling state. From Ni Wade.
- Fix a problem that OF registered thermal zones are running without
thermal governors. From Zhang Rui.
- Commit beeb5a1e0ef7 ("thermal: rcar-thermal: Enable driver
compilation with COMPILE_TEST") broke build on archs wihout io
memory. Thus make it depend on HAS_IOMEM to bypass build failures.
Fixed by Richard Weinberger"
* 'for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal: thermal zone governor fix
Thermal: Allow first update of cooling device state
thermal,rcar_thermal: Add dependency on HAS_IOMEM
x86_pkg_temp_thermal: Fix the thermal zone type
x86_pkg_temp_thermal: Do not expose as a hwmon device
Thermal: update INT3404 thermal driver help text
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A scattering of driver specific fixes here.
The fixes from Axel cover bitrot in apparently unmaintained drivers,
the at79 bug is fixing a glitch on /CS during initialisation of some
devices which could break some slaves and the remainder are fixes for
recently introduced bugs from the past release cycle or so"
* tag 'spi-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacks
spi: coldfire-qspi: Fix getting correct address for *mcfqspi
spi: fsl-dspi: Fix getting correct address for master
spi: spi-ath79: fix initial GPIO CS line setup
spi: spi-imx: spi_imx_remove: do not disable disabled clocks
spi-topcliff-pch: Fix probing when DMA mode is used
spi/topcliff-pch: Fix DMA channel
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This series addresses a number of outstanding issues wrt to active I/O
shutdown using iser-target. This includes:
- Fix a long standing tpg_state bug where a tpg could be referenced
during explicit shutdown (v3.1+ stable)
- Use list_del_init for iscsi_cmd->i_conn_node so list_empty checks
work as expected (v3.10+ stable)
- Fix a isert_conn->state related hung task bug + ensure outstanding
I/O completes during session shutdown. (v3.10+ stable)
- Fix isert_conn->post_send_buf_count accounting for RDMA READ/WRITEs
(v3.10+ stable)
- Ignore FRWR completions during active I/O shutdown (v3.12+ stable)
- Fix command leakage for interrupt coalescing during active I/O
shutdown (v3.13+ stable)
Also included is another DIF emulation fix from Sagi specific to
v3.14-rc code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix sbc_copy_prot for offset scatters
iser-target: Fix command leak for tx_desc->comp_llnode_batch
iser-target: Ignore completions for FRWRs in isert_cq_tx_work
iser-target: Fix post_send_buf_count for RDMA READ/WRITE
iscsi/iser-target: Fix isert_conn->state hung shutdown issues
iscsi/iser-target: Use list_del_init for ->i_conn_node
iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bug
|
|
Revert commit 3130497f5bab ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.
Fixes: 3130497f5bab ("ACPI / sleep: pm_power_off needs more sanity checks to be installed")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Just a couple patches blacklisting more broken devices"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8 (2BA30001)
libata: disable queued TRIM for Crucial M500 mSATA SSDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"This pull request contains a workqueue usage fix for firewire.
For quite a long time now, workqueue only treats two work items
identical iff both their addresses and callbacks match. This is to
avoid introducing false dependency through the work item being
recycled while being executed. This changes non-reentrancy guarantee
for the users of PREPARE[_DELAYED]_WORK() - if the function changes,
reentrancy isn't guaranteed against the previous instance. Firewire
depended on such nonreentrancy guarantee.
This is fixed by doing the work item multiplexing from firewire proper
while keeping the work function unchanged"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
firewire: don't use PREPARE_DELAYED_WORK
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixes from Stefan Richter:
"Fix a use-after-free regression since v3.4 and an initialization
regression since v3.10"
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: fix probe failure with Agere/LSI controllers
firewire: net: fix use after free
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk driver fix from Mike Turquette:
"Single fix for a clock driver merged in 3.14-rc1. Without this fix
the CPU frequency cannot be scaled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: shmobile: rcar-gen2: Use kick bit to allow Z clock frequency change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- ACPI tables in some BIOSes list device resources with size equal to
0, which doesn't make sense, so we should ignore them, but instead we
try to use them and mangle things completely. Fix from Zhang Rui.
- Several models of Samsung laptops accumulate EC events when they are
in sleep states which leads to EC buffer overflows that prevent new
events from being signaled after system resume or reboot. This has
been affecting many users for quite a while and may be addressed by
clearing the EC buffer during system resume and system startup on
those machines. From Kieran Clancy.
- If the ACPI sleep control and status registers are not present (which
happens if the Hardware Reduced ACPI mode bit is set in the ACPI
tables, but also may result from BIOS bugs), we should not try to use
ACPI to power off the system and ACPI S5 should not be listed as
supported. Fix from Aubrey Li.
- There's a race condition in cpufreq_get() that leads to a kernel
crash if that function is called at a wrong time. Fix from Aaron
Plattner.
- cpufreq policy objects have to be initialized entirely before they
are first accessed by their users which isn't the case currently and
that potentially leads to various kinds of breakage that is difficult
to debug. Fix from Viresh Kumar.
- Locking is missing in __cpufreq_add_dev() which leads to a race
condition that may trigger a kernel crash. Fix from Viresh Kumar.
* tag 'pm+acpi-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Clear stale EC events on Samsung systems
cpufreq: Initialize governor for a new policy under policy->rwsem
cpufreq: Initialize policy before making it available for others to use
cpufreq: use cpufreq_cpu_get() to avoid cpufreq_get() race conditions
ACPI / sleep: pm_power_off needs more sanity checks to be installed
ACPI / resources: ignore invalid ACPI device resources
|
|
* pm-cpufreq:
cpufreq: Initialize governor for a new policy under policy->rwsem
cpufreq: Initialize policy before making it available for others to use
cpufreq: use cpufreq_cpu_get() to avoid cpufreq_get() race conditions
|
|
* acpi-resources:
ACPI / resources: ignore invalid ACPI device resources
* acpi-ec:
ACPI / EC: Clear stale EC events on Samsung systems
* acpi-sleep:
ACPI / sleep: pm_power_off needs more sanity checks to be installed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- dm-cache memory allocation failure fix
- fix DM's Kconfig identation
- dm-snapshot metadata corruption fix for bug introduced in 3.14-rc1
- important refcount < 0 fix for the DM persistent data library's space
map metadata interface which fixes corruption reported by a few
dm-thinp users
and last but not least:
- more extensive fixes than ideal for dm-thinp's data resize capability
(which has had growing pain much like we've seen from -ENOSPC
handling of filesystems that mature).
The end result is dm-thinp now handles metadata operation failure and
no data space error conditions much better than before.
* tag 'dm-3.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm space map metadata: fix refcount decrement below 0 which caused corruption
dm thin: fix Documentation for held metadata root feature
dm thin: fix noflush suspend IO queueing
dm thin: fix deadlock in __requeue_bio_list
dm thin: fix out of data space handling
dm thin: ensure user takes action to validate data and metadata consistency
dm thin: synchronize the pool mode during suspend
dm snapshot: fix metadata corruption
dm: fix Kconfig indentation
dm cache mq: fix memory allocation failure for large cache devices
|
|
This reverts commit 3804fad45411b48233b48003e33a78f290d227c8.
This commit, together with commit 247bf557273dd775505fb9240d2d152f4f20d304
"xhci 1.0: Limit arbitrarily-aligned scatter gather." were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules for xHCI 1.0 hosts,
but for now, revert this patch until scatter gather can be properly supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 247bf557273dd775505fb9240d2d152f4f20d304.
This commit, together with commit 3804fad45411b48233b48003e33a78f290d227c8
"USBNET: ax88179_178a: enable tso if usb host supports sg dma" were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules required, but for now
this patch needs to be reverted to get USB 3.0 mass storage devices working at the
level they used to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DELAY_INIT quirk only reduces the frequency of enumeration failures
with the Logitech HD Pro C920 and C930e webcams, but does not quite
eliminate them. We have found that adding a delay of 100ms between the
first and second Get Configuration request makes the device enumerate
perfectly reliable even after several weeks of extensive testing. The
reasons for that are anyone's guess, but since the DELAY_INIT quirk
already delays enumeration by a whole second, wating for another 10th of
that isn't really a big deal for the one other device that uses it, and
it will resolve the problems with these webcams.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We've encountered a rare issue when enumerating two Logitech webcams
after a reboot that doesn't power cycle the USB ports. They are spewing
random data (possibly some leftover UVC buffers) on the second
(full-sized) Get Configuration request of the enumeration phase. Since
the data is random this can potentially cause all kinds of odd behavior,
and since it occasionally happens multiple times (after the kernel
issues another reset due to the garbled configuration descriptor), it is
not always recoverable. Set the USB_DELAY_INIT quirk that seems to work
around the issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently support only T10-DIF types of signature handover operations
(types 1|2|3).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This commit takes care of the generated signature error CQE generated
by the HW (if happened). The underlying mlx5 driver will handle
signature error completions and will mark the relevant memory region
as dirty.
Once the consumer gets the completion for the transaction, it must
check for signature errors on signature memory region using a new
lightweight verb ib_check_mr_status().
In case the user doesn't check for signature error (i.e. doesn't call
ib_check_mr_status() with status check IB_MR_CHECK_SIG_STATUS), the
memory region cannot be used for another signature operation
(REG_SIG_MR work request will fail).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch implements IB_WR_REG_SIG_MR posted by the user.
Baisically this WR involves 3 WQEs in order to prepare and properly
register the signature layout:
1. post UMR WR to register the sig_mr in one of two possible ways:
* In case the user registered a single MR for data so the UMR data segment
consists of:
- single klm (data MR) passed by the user
- BSF with signature attributes requested by the user.
* In case the user registered 2 MRs, one for data and one for protection,
the UMR consists of:
- strided block format which includes data and protection MRs and
their repetitive block format.
- BSF with signature attributes requested by the user.
2. post SET_PSV in order to set the memory domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
3. post SET_PSV in order to set the wire domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
* After this compound WR we place a small fence for next WR to come.
This patch also introduces some helper functions to set the BSF correctly
and determining the signature format selectors.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This will be useful when processing signature errors on a specific
key. The mlx5 driver will lookup the matching mlx5 memory region
structure and mark it as dirty (contains signature errors).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
get_umr_flags helper function might be used for types of access modes
other than ACCESS_MODE_MTT, such as ACCESS_MODE_KLM. So remove it from
helper, and callers will add their own access mode flag.
This commit does not add/change functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
As a preliminary step for signature feature which will require posting
multiple (3) WQEs for a single WR, we break post_send routine WQE
indexing into begin and finish routines.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
If user requested signature enable we initialize relevant mlx5_ib_qp
members. We mark the qp as sig_enable and we increase the effective
SQ size, but still limit the user max_send_wr to original size
computed. We also allow the create_qp routine to accept sig_enable
create flag.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Support create_mr and destroy_mr verbs. Creating ib_mr may be done
for either ib_mr that will register regular page lists like
alloc_fast_reg_mr routine, or indirect ib_mrs that can register other
(pre-registered) ib_mrs in an indirect manner.
In addition user may request signature enable, that will mean that the
created ib_mr may be attached with signature attributes (BSF, PSVs).
Currently we only allow direct/indirect registration modes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Introduce a verbs interface for signature-related operations. A
signature handover operation configures the layouts of data and
protection attributes both in memory and wire domains.
Signature operations are:
- INSERT:
Generate and insert protection information when handing over
data from input space to output space.
- validate and STRIP:
Validate protection information and remove it when handing over
data from input space to output space.
- validate and PASS:
Validate protection information and pass it when handing over
data from input space to output space.
Once the signature handover opration is done, the HCA will offload
data integrity generation/validation while performing the actual data
transfer.
Additions:
1. HCA signature capabilities in device attributes
Verbs provider supporting signature handover operations fills
relevant fields in device attributes structure returned by
ib_query_device.
2. QP creation flag IB_QP_CREATE_SIGNATURE_EN
Creating a QP that will carry signature handover operations may
require some special preparations from the verbs provider. So we
add QP creation flag IB_QP_CREATE_SIGNATURE_EN to declare that the
created QP may carry out signature handover operations. Expose
signature support to verbs layer (no support for now).
3. New send work request IB_WR_REG_SIG_MR
Signature handover work request. This WR will define the signature
handover properties of the memory/wire domains as well as the
domains layout. The purpose of this work request is to bind all
the needed information for the signature operation:
- data to be transferred: wr->sg_list (ib_sge).
* The raw data, pre-registered to a single MR (normally, before
signature, this MR would have been used directly for the data
transfer)
- data protection guards: sig_handover.prot (ib_sge).
* The data protection buffer, pre-registered to a single MR, which
contains the data integrity guards of the raw data blocks.
Note that it may not always exist, only in cases where the user is
interested in storing protection guards in memory.
- signature operation attributes: sig_handover.sig_attrs.
* Tells the HCA how to validate/generate the protection information.
Once the work request is executed, the memory region that will
describe the signature transaction will be the sig_mr. The
application can now go ahead and send the sig_mr.rkey or use the
sig_mr.lkey for data transfer.
4. New Verb ib_check_mr_status
check_mr_status verb checks the status of the memory region post
transaction. The first check that may be used is
IB_MR_CHECK_SIG_STATUS, which will indicate if any signature
errors are pending for a specific signature-enabled ib_mr. This
verb is a lightwight check and is allowed to be taken from
interrupt context. An application must call this verb after it is
known that the actual data transfer has finished.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This commit introduces verbs for creating/destoying memory
regions which will allow new types of memory key operations such
as protected memory registration.
Indirect memory registration is registering several (one
of more) pre-registered memory regions in a specific layout.
The Indirect region may potentialy describe several regions
and some repitition format between them.
Protected Memory registration is registering a memory region
with various data integrity attributes which will describe protection
schemes that will be handled by the HCA in an offloaded manner.
These memory regions will be applicable for a new REG_SIG_MR
work request introduced later in this patchset.
In the future these routines may replace or implement current memory
regions creation routines existing today:
- ib_reg_user_mr
- ib_alloc_fast_reg_mr
- ib_get_dma_mr
- ib_dereg_mr
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
M8 (2BA30001)
Via commit 87809942d3fa "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk
for Seagate Momentus SpinPoint M8" we added a quirk for disks named
"ST1000LM024 HN-M101MBB" with firmware revision "2AR10001".
As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901,
we need to also add firmware revision 2BA30001 as it is broken as well.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Pull drm fixes from Dave Airlie:
"Mostly intel and radeon fixes, one tda998x, one kconfig dep fix and
two more MAINTAINERS updates,
All pretty run of the mill for this stage"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/atom: select the proper number of lanes in transmitter setup
MAINTAINERS: add maintainer entry for TDA998x driver
drm: fix bochs kconfig dependencies
drm/radeon/dpm: fix typo in EVERGREEN_SMC_FIRMWARE_HEADER_softRegisters
drm/radeon/cik: fix typo in documentation
drm/radeon: silence GCC warning on 32 bit
drm/radeon: resume old pm late
drm/radeon: TTM must be init with cpu-visible VRAM, v2
DRM: armada: fix use of kfifo_put()
drm/i915: Reject >165MHz modes w/ DVI monitors
drm/i915: fix assert_cursor on BDW
drm/i915: vlv: reserve GT power context early
drm/i915: fix pch pci device enumeration
drm/i915: Resolving the memory region conflict for Stolen area
drm/i915: use backlight legacy combination mode also for i915gm/i945gm
MAINTAINERS: update AGP tree to point at drm tree
|
|
Pull block fixes from Jens Axboe:
"Small collection of fixes for 3.14-rc. It contains:
- Three minor update to blk-mq from Christoph.
- Reduce number of unaligned (< 4kb) in-flight writes on mtip32xx to
two. From Micron.
- Make the blk-mq CPU notify spinlock raw, since it can't be a
sleeper spinlock on RT. From Mike Galbraith.
- Drop now bogus BUG_ON() for bio iteration with blk integrity. From
Nic Bellinger.
- Properly propagate the SYNC flag on requests. From Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: add REQ_SYNC early
rt,blk,mq: Make blk_mq_cpu_notify_lock a raw spinlock
bio-integrity: Drop bio_integrity_verify BUG_ON in post bip->bip_iter world
blk-mq: support partial I/O completions
blk-mq: merge blk_mq_insert_request and blk_mq_run_request
blk-mq: remove blk_mq_alloc_rq
mtip32xx: Reduce the number of unaligned writes to 2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"This is a set of pin control fixes I have collected over the last few
days. Some have rotated more than others in linux-next, but they were
rebased on v3.14-rc5 due to sloppy commit messages. I am quite
convinced that they are all good fixes that only hit this or that
individual driver and not the entire subsystem.
- Fix chained interrupts, interrupt masking and register offset
calculation for the sunxi driver
- Make MSM a bool rather than a tristate to stop build problems to
happen - chained interrupt controllers cannot currently be defined
in modules
- Fix a clock in the PFC driver
- Fix a kernel panic in the sirf driver"
* tag 'pinctrl-v3.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sirf: fix kernel panic in gpio_lock_as_irq
pinctrl: sh-pfc: r8a7791: SD1_CLK fix
pinctrl: msm: make PINCTRL_MSM bool instead of tristate
pinctrl: sunxi: Fix interrupt register offset calculation
pinctrl: sunxi: Fix masking when setting irq type
pinctrl: sunxi: use chained_irq_{enter, exit} for GIC compatibility
|
|
This has been a relatively long-standing issue that wasn't nailed down
until Teng-Feng Yang's meticulous bug report to dm-devel on 3/7/2014,
see: http://www.redhat.com/archives/dm-devel/2014-March/msg00021.html
From that report:
"When decreasing the reference count of a metadata block with its
reference count equals 3, we will call dm_btree_remove() to remove
this enrty from the B+tree which keeps the reference count info in
metadata device.
The B+tree will try to rebalance the entry of the child nodes in each
node it traversed, and the rebalance process contains the following
steps.
(1) Finding the corresponding children in current node (shadow_current(s))
(2) Shadow the children block (issue BOP_INC)
(3) redistribute keys among children, and free children if necessary (issue BOP_DEC)
Since the update of a metadata block's reference count could be
recursive, we will stash these reference count update operations in
smm->uncommitted and then process them in a FILO fashion.
The problem is that step(3) could free the children which is created
in step(2), so the BOP_DEC issued in step(3) will be carried out
before the BOP_INC issued in step(2) since these BOPs will be
processed in FILO fashion. Once the BOP_DEC from step(3) tries to
decrease the reference count of newly shadow block, it will report
failure for its reference equals 0 before decreasing. It looks like we
can solve this issue by processing these BOPs in a FIFO fashion
instead of FILO."
Commit 5b564d80 ("dm space map: disallow decrementing a reference count
below zero") changed the code to report an error for this temporary
refcount decrement below zero. So what was previously a harmless
invalid refcount became a hard failure due to the new error path:
device-mapper: space map common: unable to decrement a reference count below 0
device-mapper: thin: 253:6: dm_thin_insert_block() failed: error = -22
device-mapper: thin: 253:6: switching pool to read-only mode
This bug is in dm persistent-data code that is common to the DM thin and
cache targets. So any users of those targets should apply this fix.
Fix this by applying recursive space map operations in FIFO order rather
than FILO.
Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=68801
Reported-by: Apollon Oikonomopoulos <apoikos@debian.org>
Reported-by: edwillam1007@gmail.com
Reported-by: Teng-Feng Yang <shinrairis@gmail.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.13+
|
|
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
firewire core-device and sbp2 have been been multiplexing work items
with multiple work functions. Introduce fw_device_workfn() and
sbp2_lu_workfn() which invoke fw_device->workfn and
sbp2_logical_unit->workfn respectively and always use the two
functions as the work functions and update the users to set the
->workfn fields instead of overriding work functions using
PREPARE_DELAYED_WORK().
This fixes a variety of possible regressions since a2c1c57be8d9
"workqueue: consider work function when searching for busy work items"
due to which fw_workqueue lost its required non-reentrancy property.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: linux1394-devel@lists.sourceforge.net
Cc: stable@vger.kernel.org # v3.9+
Cc: stable@vger.kernel.org # v3.8.2+
Cc: stable@vger.kernel.org # v3.4.60+
Cc: stable@vger.kernel.org # v3.2.40+
|
|
When copying between device and command protection scatters
we must take into account that device scatters might be offset
and we might copy outside scatter range. Thus for each cmd prot
scatter we must take the min between cmd prot scatter, dev prot
scatter, and whats left (and loop in case we havn't copied enough
from/to cmd prot scatter).
Example (single t_prot_sg of len 2048):
kernel: sbc_dif_copy_prot: se_cmd=ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096
kernel: isert: se_cmd=ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580
Instead of copying 2048 from offset 3072 (copying junk outside sg
limit 4096), we must to copy 1024 and continue to next sg until
we complete cmd prot scatter.
This issue was found using iSER T10-PI offload over rd_mcp (wasn't
discovered with fileio since file_dev prot sglists are never offset).
Changes from v1:
- Fix sbc_copy_prot copy length miss-calculation
Changes from v0:
- Removed psg->offset consideration for psg_len computation
- Removed sg->offset consideration for offset condition
- Added copied consideraiton for len computation
- Added copied offset to paddr when doing memcpy
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
'spi/fix/coldfire', 'spi/fix/fsl-dspi', 'spi/fix/imx' and 'spi/fix/topcliff-pch' into spi-linus
|
|
into drm-fixes
one more radeon fix.
* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/atom: select the proper number of lanes in transmitter setup
|
|
We need to check for DVI vs. HDMI when setting up duallink since
HDMI is single link only. Fixes 4k modes on newer asics.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=75223
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://ftp.arm.linux.org.uk/~rmk/linux-cubox into drm-fixes
fix for kfifo api change.
* 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
DRM: armada: fix use of kfifo_put()
|
|
Should be at 0x8 rather than 0.
fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60523
Noticed by ArtForz on #radeon
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Copy-paste typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Building radeon_ttm.o on 32 bit x86 triggers a warning:
In file included from include/asm-generic/bug.h:13:0,
from [...]/arch/x86/include/asm/bug.h:38,
from include/linux/bug.h:4,
from include/drm/drm_mm.h:39,
from include/drm/drm_vma_manager.h:26,
from include/drm/ttm/ttm_bo_api.h:35,
from drivers/gpu/drm/radeon/radeon_ttm.c:32:
drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_gtt_read':
include/linux/kernel.h:712:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
(void) (&_min1 == &_min2); \
^
drivers/gpu/drm/radeon/radeon_ttm.c:938:22: note: in expansion of macro 'min'
ssize_t cur_size = min(size, PAGE_SIZE - off);
^
Silence this warning by using min_t(). Since cur_size will never be
negative and its upper bound is PAGE_SIZE, we can change its type to
size_t and use min_t(size_t, [...]) here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
