| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove an inline from a fairly big function that is used often. It's
unlikely that calling or not calling it makes a lot of difference.
Saves around 8k text in my kernel.
text data bss dec hex filename
9047801 5367568 11116544 25531913 1859609 vmlinux-before-megasas
9039417 5367568 11116544 25523529 1857549 vmlinux-megasas
Link: http://lkml.kernel.org/r/20170315021431.13107-7-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Kashyap Desai <kashyap.desai@avagotech.com>
Cc: Sumit Saxena <sumit.saxena@avagotech.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Return value check of atomic_dec_if_positive is required as it returns
old value minus one. Without this fix, driver will send small ios to
firmware path and that will be a performance issue.
Not critical, but good to have r1_ldio_hint as default value in sdev
private.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Without this fix, driver will enable INTx Interrupt pin even though
MSI-x vectors are enabled. See below lspci output. DisINTx is unset for
MSIx setup.
lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
After applying this fix, driver will enable INTx Interrupt pin only if
Legacy interrupt method is required. See below lspci output. DisINTx is
set for MSIx setup. lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The "sz" variable is in terms of bytes, but we're treating the buffer as
an array of __le32 so we have to divide by 4.
Fixes: def0eab3af86 ("scsi: megaraid_sas: enhance debug logs in OCR context")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix indentation issues and smatch warning reported by Dan Carpenter
for previous series as discussed below.
http://www.spinics.net/lists/linux-scsi/msg103635.html
http://www.spinics.net/lists/linux-scsi/msg103603.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Error handling: Bail out the driver load if key FW cmds (LD_LIST) are
not return successful. Clean up error handling in megasas_init_fw.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Memset the IO frame to zero after release.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since maximum supported FW commands are all defined as u16, change
all local variables referring to max_cmd from u32 to u16.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
shutdown DCMD
Fetch the latest controller OCR capability from FW before sending
MR_DCMD_CTRL_SHUTDOWN When application sends a shutdown DCMD
(MR_DCMD_CTRL_SHUTDOWN), driver will fetch latest controller information
from firmware. This is to ensure that driver always has latest OCR
capability of controller before sending the DCMD.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix kernel warning for accessing unaligned memory access in driver.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
fails
Currently fusion context has fixed array load_balance_info. Use dynamic
allocation. In few places, driver do not want physically contigious
memory. Attempt to use vmalloc if physical contiguous memory is not
available.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add additional logging from driver in OCR context.
Add debug logs for partial completion of IOs is iodone context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fetch true values of NVME property from FW using New DCMD
interface MR_DCMD_DEV_GET_TARGET_PROP
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Adding detection logic for NVME device attached behind Ventura
controller. Driver set HostPageSize in IOC_INIT frame to inform about
page size for NVME devices. Firmware reports NVME page size to the
driver. PD INFO DCMD provide new interface type NVME_PD. Driver set
property of NVME device.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
With the changes to remove checks for a valid request descriptor,
issue_dcmd will now always return DCMD_SUCCESS. This patch changes
return type of issue_dcmd to void and change all callers appropriately.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Moving to use DID_REQUEUE return type for reliable unconditional
retries. Driver wants unconditional re-queue, so replace DID_RESET with
DID_REQUEUE
Discussed below -
https://www.spinics.net/lists/linux-scsi/msg102848.html
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
is not set
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Threshold Bandwidth"
This reverts commit "3e5eadb1a881" ("scsi: megaraid_sas: Enable or
Disable Fast path based on the PCI Threshold Bandwidth")
This patch was aimed to increase performance of R1 Write operation for
large IO size. Since this method used timer approach, it turn on/off
fast path did not work as expected. Patch 0013 describes new algorithm
and performance number.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Controllers
Update Linux driver to use new pdTargetId field for JBOD target ID
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Bandwidth
Large SEQ IO workload should sent as non fast path commands
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Capabilities
The Megaraid driver has to support the SAS3.5 Generic Megaraid Controllers Firmware functionality.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Controllers
SAS3.5 Generic Megaraid Controllers FW will support new dynamic RaidMap to have different
sizes for different number of supported VDs.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
IO Coalescing
Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.
Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SAS3.5 Generic Megaraid based Controllers will have the support for 128 MSI-X vectors,
resulting in the need to support 128 reply queues
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Controllers
This patch contains new pci device ids for SAS3.5 Generic Megaraid Controllers
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[mkp: fixed bad indentation]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is not good when an irq arrives before driver structures are
allocated.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A couple of dev_printk messages spans two lines and the literal string
is missing a white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Until now the megaraid_sas driver has reported successful completion on
SYNCHRONIZE_CACHE commands without sending them down to the controller.
The controller firmware has been responsible for taking care of flushing
disk caches for all drives that belong to a Virtual Disk at the time of
system reboot/shutdown.
There may have been a reason to avoid sending SYNCHRONIZE_CACHE to a VD
in the past but that no longer appears to be valid.
Older versions of MegaRaid firmware (Gen2 and Gen2.5) set the WCE bit
for Virtual Disks but the firmware does not report correct completion
status for a SYNCHRONIZE_CACHE command. As a result, we must use another
method to identify whether it is safe to send the command to the
controller. We use the canHandleSyncCache firmware flag in the scratch
pad register at offset 0xB4.
New SYNCHRONIZE_CACHE behavior:
IF 'JBOD'
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware sends SYNCHRONIZE_CACHE to drive
Firmware obtains status from drive and returns same status back to driver
ELSEIF 'VirtualDisk'
IF firmware supports new API bit called canHandleSyncCache
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware does not send SYNCHRONIZE_CACHE to drives
Firmware returns SUCCESS
ELSE
Driver does not send SYNCHRONIZE_CACHE command to the firmware
Driver return SUCCESS for that command
ENDIF
ENDIF
[mkp: edited patch description]
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch addresses the issue of driver firing DCMDs in PCI
shutdown/detach path irrespective of firmware state. Driver will now
check whether firmware is in operational state or not before firing
DCMDs. If firmware is in unrecoverable state or does not become
operational within specfied time, driver will skip firing DCMDs.
[mkp: fixed typos]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 02b01e010afe ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010afeeb49328d35650d70721d2ca3fd59
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (hpsa,
be2iscsi, hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa
called smartpqi for which a driver is added, there's some cleanup work
of the ibm vscsi target and updates to libfc, plus a whole host of
minor fixes and updates and finally the removal of several ISA drivers
which seem not to have been used for years"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (173 commits)
scsi: mvsas: Mark symbols static where possible
scsi: pm8001: Mark symbols static where possible
scsi: arcmsr: Simplify user_len checking
scsi: fcoe: fix off by one in eth2fc_speed()
scsi: dtc: remove from tree
scsi: t128: remove from tree
scsi: pas16: remove from tree
scsi: u14-34f: remove from tree
scsi: ultrastor: remove from tree
scsi: in2000: remove from tree
scsi: wd7000: remove from tree
scsi: scsi_dh_alua: Fix memory leak in alua_rtpg()
scsi: lpfc: Mark symbols static where possible
scsi: hpsa: correct call to hpsa_do_reset
scsi: ufs: Get a TM service response from the correct offset
scsi: ibmvfc: Fix I/O hang when port is not mapped
scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up
scsi: ipr: Remove redundant messages at adapter init time
scsi: ipr: Don't log unnecessary 9084 error details
scsi: smartpqi: raid bypass lba calculation fix
...
|
|
We get a few warnings when building kernel with W=1:
drivers/scsi/megaraid/megaraid_sas_fusion.c:281:1: warning: no previous prototype for 'megasas_free_cmds_fusion' [-Wmissing-prototypes]
drivers/scsi/megaraid/megaraid_sas_fusion.c:714:1: warning: no previous prototype for 'megasas_ioc_init_fusion' [-Wmissing-prototypes]
....
In fact, these functions are declared in
drivers/scsi/megaraid/megaraid_sas_base.c, but should be declared in a
header file, thus can be recognized in other file.
So this patch adds the declarations into
drivers/scsi/megaraid/megaraid_sas_fusion.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A dev_printk message spans two lines and the literal string is missing a
white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(unsigned long)' which is likely to
be 4.
It is likely that the number of bits in a long was expected here, so use
BITS_PER_LONG instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Found one megaraid_sas HBA probe fails,
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b4c ("megaraid_sas: Use lowest memory bar for SR-IOV VF support")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
support it
There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ). Below are the error logs reported
continuously-
Jun 25 08:49:30 ns8 kernel: [ 757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY. In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.
Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.
Reported-by: Lucz Geza <geza@lucz.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
I actually read the error messages in my logs, and successful
initialization is not an error.
Arguably these log lines could be deleted entirely.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will do code optmization for task management functions.
Below are key changes:
1. Remove reset_device hook as it was not being used and driver was
setting this to NULL.
2. Create wrapper functions for task abort and target reset and inside
these functions adapter specific calls be made. e.g. fusion adapters
support task abort and target reset so task abort and target reset
should be issued to fusion adapters only and for MFI adapters, print
a message saying feature not supported.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode. Driver will not allocate memory for optional and
perfromance oriented features. Below are key changes done in
megaraid_sas driver to do this:
1. Limit Controller's queue depth to 100 in kdump mode.
2. Do not allocate memory for system info buffer and PD info buffer.
3. Disable performance oriented features e.g. Disable RDPQ mode, disable
dual queue depth, restrict to single MSI-x vector.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
gcc-6 found a dubious indentation in the megasas_mgmt_fw_ioctl
function:
drivers/scsi/megaraid/megaraid_sas_base.c: In function 'megasas_mgmt_fw_ioctl':
drivers/scsi/megaraid/megaraid_sas_base.c:6658:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
kbuff_arr[i] = NULL;
^~~~~~~~~
drivers/scsi/megaraid/megaraid_sas_base.c:6653:3: note: ...this 'if' clause, but it is not
if (kbuff_arr[i])
^~
The code is actually correct, as there is no downside in clearing a NULL
pointer again.
This clarifies the code and avoids the warning by adding extra curly
braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 90dc9d98f01b ("megaraid_sas : MFI MPT linked list corruption fix")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
list DCMD failure
There are few MFI adapters which do not support MR_DCMD_PD_LIST_QUERY so
if MFI adapters fail this DCMD, it should not be considered as FATAL and
driver should not issue kill adapter and set per controller's instance
variable- pd_list_not_supported so that same variable can be used inside
functions- slave_alloc and slave_configure to allow firmware scan.
Killing adapter because of DCMD failure when this DCMD is not supported
causes driver's probe getting failed. This issue got introduced by
commit 6d40afbc7d13 ("megaraid_sas: MFI IO timeout handling").
Killing adapter in case of this DCMD failure should be limited to Fusion
adapters only. Per controller's instance variable allow_fw_scan is
removed as pd_list_not_supported better reflect the purpose.
Fixes: 6d40afbc7d13359b30a5cd783e3db6ebefa5f40a
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A barrier should be added to ensure proper ordering of memory mapped
writes.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Inside compat IOCTL hook of driver, driver was using wrong address of
ioc->frame.raw which leads sense_ioc_ptr to be calculated wrongly and
failing IOCTL.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver assumes that VFs always have peers present whenever they have
same LD IDs. But this is not the case. This patch handles the above
mentioned by explicitly checking for a peer before making HA/non-HA path
decision.
Signed-off-by: Uday Lingala <uday.lingala@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
