diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt | 93 |
1 files changed, 80 insertions, 13 deletions
diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt index 33a2b1ee3f3e..0acc5a99fb79 100644 --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -6,12 +6,11 @@ This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. Required properties (controller (parent) node): - compatible : should be one of "mediatek,mt2701-u3phy" + "mediatek,mt2712-u3phy" "mediatek,mt8173-u3phy" - - reg : offset and length of register for phy, exclude port's - register. - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain + - clocks : (deprecated, use port's clocks instead) a list of phandle + + clock-specifier pairs, one for each entry in clock-names + - clock-names : (deprecated, use port's one instead) must contain "u3phya_ref": for reference clock of usb3.0 analog phy. Required nodes : a sub-node is required for each port the controller @@ -19,8 +18,19 @@ Required nodes : a sub-node is required for each port the controller 'reg' property is used inside these nodes to describe the controller's topology. +Optional properties (controller (parent) node): + - reg : offset and length of register shared by multiple ports, + exclude port's private register. It is needed on mt2701 + and mt8173, but not on mt2712. + Required properties (port (child) node): - reg : address and length of the register set for the port. +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names +- clock-names : must contain + "ref": 48M reference clock for HighSpeed analog phy; and 26M + reference clock for SuperSpeed analog phy, sometimes is + 24M, 25M or 27M, depended on platform. - #phy-cells : should be 1 (See second example) cell after port phandle is phy type from: - PHY_TYPE_USB2 @@ -31,21 +41,31 @@ Example: u3phy: usb-phy@11290000 { compatible = "mediatek,mt8173-u3phy"; reg = <0 0x11290000 0 0x800>; - clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; - clock-names = "u3phya_ref"; #address-cells = <2>; #size-cells = <2>; ranges; status = "okay"; - phy_port0: port@11290800 { - reg = <0 0x11290800 0 0x800>; + u2port0: usb-phy@11290800 { + reg = <0 0x11290800 0 0x100>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "ref"; #phy-cells = <1>; status = "okay"; }; - phy_port1: port@11291000 { - reg = <0 0x11291000 0 0x800>; + u3port0: usb-phy@11290900 { + reg = <0 0x11290800 0 0x700>; + clocks = <&clk26m>; + clock-names = "ref"; + #phy-cells = <1>; + status = "okay"; + }; + + u2port1: usb-phy@11291000 { + reg = <0 0x11291000 0 0x100>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "ref"; #phy-cells = <1>; status = "okay"; }; @@ -64,7 +84,54 @@ Example: usb30: usb@11270000 { ... - phys = <&phy_port0 PHY_TYPE_USB3>; - phy-names = "usb3-0"; + phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>; + phy-names = "usb2-0", "usb3-0"; ... }; + + +Layout differences of banks between mt8173/mt2701 and mt2712 +------------------------------------------------------------- +mt8173 and mt2701: +port offset bank +shared 0x0000 SPLLC + 0x0100 FMREG +u2 port0 0x0800 U2PHY_COM +u3 port0 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA +u2 port1 0x1000 U2PHY_COM +u3 port1 0x1100 U3PHYD + 0x1200 U3PHYD_BANK2 + 0x1300 U3PHYA + 0x1400 U3PHYA_DA +u2 port2 0x1800 U2PHY_COM + ... + +mt2712: +port offset bank +u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM +u3 port0 0x0700 SPLLC + 0x0800 CHIP + 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA +u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM +u3 port1 0x1700 SPLLC + 0x1800 CHIP + 0x1900 U3PHYD + 0x1a00 U3PHYD_BANK2 + 0x1b00 U3PHYA + 0x1c00 U3PHYA_DA +u2 port2 0x2000 MISC + ... + + SPLLC shared by u3 ports and FMREG shared by u2 ports on +mt8173/mt2701 are put back into each port; a new bank MISC for +u2 ports and CHIP for u3 ports are added on mt2712. |