| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Final nlmsg_len field update must reflect inserted net_dm_drop_point
data.
This patch depends on previous patch:
"drop_monitor: add missing call to genlmsg_end"
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of custom rules being present we need to handle the case of the
LOCAL table being intialized after the new rule has been added. To address
that I am adding a new check so that we can make certain we don't use an
alias of MAIN for LOCAL when allocating a new table.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Oliver Brunel <jjk@jjacky.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
5.2. Action on Reception of a Query
When a system receives a Query, it does not respond immediately.
Instead, it delays its response by a random amount of time, bounded
by the Max Resp Time value derived from the Max Resp Code in the
received Query message. A system may receive a variety of Queries on
different interfaces and of different kinds (e.g., General Queries,
Group-Specific Queries, and Group-and-Source-Specific Queries), each
of which may require its own delayed response.
Before scheduling a response to a Query, the system must first
consider previously scheduled pending responses and in many cases
schedule a combined response. Therefore, the system must be able to
maintain the following state:
o A timer per interface for scheduling responses to General Queries.
o A per-group and interface timer for scheduling responses to Group-
Specific and Group-and-Source-Specific Queries.
o A per-group and interface list of sources to be reported in the
response to a Group-and-Source-Specific Query.
When a new Query with the Router-Alert option arrives on an
interface, provided the system has state to report, a delay for a
response is randomly selected in the range (0, [Max Resp Time]) where
Max Resp Time is derived from Max Resp Code in the received Query
message. The following rules are then used to determine if a Report
needs to be scheduled and the type of Report to schedule. The rules
are considered in order and only the first matching rule is applied.
1. If there is a pending response to a previous General Query
scheduled sooner than the selected delay, no additional response
needs to be scheduled.
2. If the received Query is a General Query, the interface timer is
used to schedule a response to the General Query after the
selected delay. Any previously pending response to a General
Query is canceled.
--8<--
Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.
Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.
Signed-off-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__skb_flow_dissect can be called with a skb or a data packet, either
can be NULL. All calls seems to have been moved to __skb_header_pointer
except the pptp handling which is still calling skb_header_pointer.
skb_header_pointer will use skb->data and thus:
[ 109.556866] BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
[ 109.557102] IP: [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[ 109.557263] PGD 0
[ 109.557338]
[ 109.557484] Oops: 0000 [#1] SMP
[ 109.557562] Modules linked in: chaoskey
[ 109.557783] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.9.0 #79
[ 109.557867] Hardware name: Supermicro A1SRM-LN7F/LN5F/A1SRM-LN7F-2758, BIOS 1.0c 11/04/2015
[ 109.557957] task: ffff94085c27bc00 task.stack: ffffb745c0068000
[ 109.558041] RIP: 0010:[<ffffffff88dc02f8>] [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[ 109.558203] RSP: 0018:ffff94087fc83d40 EFLAGS: 00010206
[ 109.558286] RAX: 0000000000000130 RBX: ffffffff8975bf80 RCX: ffff94084fab6800
[ 109.558373] RDX: 0000000000000010 RSI: 000000000000000c RDI: 0000000000000000
[ 109.558460] RBP: 0000000000000b88 R08: 0000000000000000 R09: 0000000000000022
[ 109.558547] R10: 0000000000000008 R11: ffff94087fc83e04 R12: 0000000000000000
[ 109.558763] R13: ffff94084fab6800 R14: ffff94087fc83e04 R15: 000000000000002f
[ 109.558979] FS: 0000000000000000(0000) GS:ffff94087fc80000(0000) knlGS:0000000000000000
[ 109.559326] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 109.559539] CR2: 0000000000000080 CR3: 0000000281809000 CR4: 00000000001026e0
[ 109.559753] Stack:
[ 109.559957] 000000000000000c ffff94084fab6822 0000000000000001 ffff94085c2b5fc0
[ 109.560578] 0000000000000001 0000000000002000 0000000000000000 0000000000000000
[ 109.561200] 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 109.561820] Call Trace:
[ 109.562027] <IRQ>
[ 109.562108] [<ffffffff88dfb4fa>] ? eth_get_headlen+0x7a/0xf0
[ 109.562522] [<ffffffff88c5a35a>] ? igb_poll+0x96a/0xe80
[ 109.562737] [<ffffffff88dc912b>] ? net_rx_action+0x20b/0x350
[ 109.562953] [<ffffffff88546d68>] ? __do_softirq+0xe8/0x280
[ 109.563169] [<ffffffff8854704a>] ? irq_exit+0xaa/0xb0
[ 109.563382] [<ffffffff8847229b>] ? do_IRQ+0x4b/0xc0
[ 109.563597] [<ffffffff8902d4ff>] ? common_interrupt+0x7f/0x7f
[ 109.563810] <EOI>
[ 109.563890] [<ffffffff88d57530>] ? cpuidle_enter_state+0x130/0x2c0
[ 109.564304] [<ffffffff88d57520>] ? cpuidle_enter_state+0x120/0x2c0
[ 109.564520] [<ffffffff8857eacf>] ? cpu_startup_entry+0x19f/0x1f0
[ 109.564737] [<ffffffff8848d55a>] ? start_secondary+0x12a/0x140
[ 109.564950] Code: 83 e2 20 a8 80 0f 84 60 01 00 00 c7 04 24 08 00
00 00 66 85 d2 0f 84 be fe ff ff e9 69 fe ff ff 8b 34 24 89 f2 83 c2
04 66 85 c0 <41> 8b 84 24 80 00 00 00 0f 49 d6 41 8d 31 01 d6 41 2b 84
24 84
[ 109.569959] RIP [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[ 109.570245] RSP <ffff94087fc83d40>
[ 109.570453] CR2: 0000000000000080
Fixes: ab10dccb1160 ("rps: Inspect PPTP encapsulated by GRE to get flow hash")
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ieee80211_xmit_fast(), 'info' is initialized to point to the skb
that's passed in, but that skb may later be replaced by a clone (if
it was shared), leading to an invalid pointer.
This can lead to use-after-free and also later crashes since the
real SKB's info->hw_queue doesn't get initialized properly.
Fix this by assigning info only later, when it's needed, after the
skb replacement (may have) happened.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For connected sockets, __l2tp_ip{,6}_bind_lookup() needs to check the
remote IP when looking for a matching socket. Otherwise a connected
socket can receive traffic not originating from its peer.
Drop l2tp_ip_bind_lookup() and l2tp_ip6_bind_lookup() instead of
updating their prototype, as these functions aren't used.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An L2TP socket bound to the unspecified address should match with any
address. If not, it can't receive any packet and __l2tp_ip6_bind_lookup()
can't prevent another socket from binding on the same device/tunnel ID.
While there, rename the 'addr' variable to 'sk_laddr' (local addr), to
make following patch clearer.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
->setattr() was recently implemented for socket files to sync the socket
inode's uid to the new 'sk_uid' member of struct sock. It does this by
copying over the ia_uid member of struct iattr. However, ia_uid is
actually only valid when ATTR_UID is set in ia_valid, indicating that
the uid is being changed, e.g. by chown. Other metadata operations such
as chmod or utimes leave ia_uid uninitialized. Therefore, sk_uid could
be set to a "garbage" value from the stack.
Fix this by only copying the uid over when ATTR_UID is set.
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 output routes already use l3mdev device instead of loopback for dst's
if it is applicable. Change local input routes to do the same.
This fixes icmp responses for unreachable UDP ports which are directed
to the wrong table after commit 9d1a6c4ea43e4 because local_input
routes use the loopback device. Moving from ingress device to loopback
loses the L3 domain causing responses based on the dst to get to lost.
Fixes: 9d1a6c4ea43e4 ("net: icmp_route_lookup should use rt dev to
determine L3 domain")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we send a packet for our own local address on a non-loopback
interface (e.g. eth0), due to the change had been introduced from
commit 0b922b7a829c ("net: original ingress device index in PKTINFO"), the
original ingress device index would be set as the loopback interface.
However, the packet should be considered as if it is being arrived via the
sending interface (eth0), otherwise it would break the expectation of the
userspace application (e.g. the DHCPRELEASE message from dhcp_release
binary would be ignored by the dnsmasq daemon, since it come from lo which
is not the interface dnsmasq bind to)
Fixes: 0b922b7a829c ("net: original ingress device index in PKTINFO")
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Wei Zhang <asuka.com@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We miss to check if the netlink message is actually big enough to contain
a struct if_stats_msg.
Add a check to prevent userland from sending us short messages that would
make us access memory beyond the end of the message.
Fixes: 10c9ead9f3c6 ("rtnetlink: add new RTM_GETSTATS message to dump...")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__ip6_append_data and ip6_finish_output
There is an inconsistent conditional judgement between __ip6_append_data
and ip6_finish_output functions, the variable length in __ip6_append_data
just include the length of application's payload and udp6 header, don't
include the length of ipv6 header, but in ip6_finish_output use
(skb->len > ip6_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ipv6 header.
That causes some particular application's udp6 payloads whose length are
between (MTU - IPv6 Header) and MTU were fragmented by ip6_fragment even
though the rst->dev support UFO feature.
Add the length of ipv6 header to length in __ip6_append_data to keep
consistent conditional judgement as ip6_finish_output for ip6 fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following warnings when CONFIG_PROC_FS is not set:
linux/net/atm/lec.c: In function ‘lane_module_cleanup’:
linux/net/atm/lec.c:1062:27: error: ‘atm_proc_root’ undeclared (first
use in this function)
remove_proc_entry("lec", atm_proc_root);
^
linux/net/atm/lec.c:1062:27: note: each undeclared identifier is
reported only once for each function it appears in
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now use a non zero mask on addr_type, we are matching on its
value (IPV4/IPV6). So before this fix, matching on enc_src_ip/enc_dst_ip
failed in SW/classify path since its value was zero.
This patch sets the proper value of addr_type for encapsulated packets.
Fixes: 970bfcd09791 ('net/sched: cls_flower: Use mask for addr_type')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
|
|
After commit 73b62bd085f4737679ea9afc7867fa5f99ba7d1b ("virtio-net:
remove the warning before XDP linearizing"), there's no users for
bpf_warn_invalid_xdp_buffer(), so remove it. This is a revert for
commit f23bc46c30ca5ef58b8549434899fcbac41b2cfc.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.
Fixes: 5108bbaddc ("openvswitch: add processing of L3 packets").
CC: Jarno Rajahalme <jarno@ovn.org>
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shahar reported a soft lockup in tc_classify(), where we run into an
endless loop when walking the classifier chain due to tp->next == tp
which is a state we should never run into. The issue only seems to
trigger under load in the tc control path.
What happens is that in tc_ctl_tfilter(), thread A allocates a new
tp, initializes it, sets tp_created to 1, and calls into tp->ops->change()
with it. In that classifier callback we had to unlock/lock the rtnl
mutex and returned with -EAGAIN. One reason why we need to drop there
is, for example, that we need to request an action module to be loaded.
This happens via tcf_exts_validate() -> tcf_action_init/_1() meaning
after we loaded and found the requested action, we need to redo the
whole request so we don't race against others. While we had to unlock
rtnl in that time, thread B's request was processed next on that CPU.
Thread B added a new tp instance successfully to the classifier chain.
When thread A returned grabbing the rtnl mutex again, propagating -EAGAIN
and destroying its tp instance which never got linked, we goto replay
and redo A's request.
This time when walking the classifier chain in tc_ctl_tfilter() for
checking for existing tp instances we had a priority match and found
the tp instance that was created and linked by thread B. Now calling
again into tp->ops->change() with that tp was successful and returned
without error.
tp_created was never cleared in the second round, thus kernel thinks
that we need to link it into the classifier chain (once again). tp and
*back point to the same object due to the match we had earlier on. Thus
for thread B's already public tp, we reset tp->next to tp itself and
link it into the chain, which eventually causes the mentioned endless
loop in tc_classify() once a packet hits the data path.
Fix is to clear tp_created at the beginning of each request, also when
we replay it. On the paths that can cause -EAGAIN we already destroy
the original tp instance we had and on replay we really need to start
from scratch. It seems that this issue was first introduced in commit
12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining
and avoid kernel panic when we use cls_cgroup").
Fixes: 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup")
Reported-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit 6f00089c7372 ("tipc: remove SS_DISCONNECTING state") the
check for socket type is in the wrong place, causing a closing socket
to always send out a FIN message even when the socket was never
connected. This is normally harmless, since the destination node for
such messages most often is zero, and the message will be dropped, but
it is still a wrong and confusing behavior.
We fix this in this commit.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if SCTP closes the receive window with window pressure, mostly
caused by excessive skb overhead on payload/overheads ratio, SCTP will
close the window abruptly while saving the delta on rwnd_press. It will
start recovering rwnd as the chunks are consumed by the application and
the rwnd_press will be only recovered after rwnd reach the same value as
of rwnd_press, mostly to prevent silly window syndrome.
Thing is, this is very inefficient with small data chunks, as with those
it will never reach back that value, and thus it will never recover from
such pressure. This means that we will not issue window updates when
recovering from 0 window and will rely on a sender retransmit to notice
it.
The fix here is to remove such threshold, as no value is good enough: it
depends on the (avg) chunk sizes being used.
Test with netperf -t SCTP_STREAM -- -m 1, and trigger 0 window by
sending SIGSTOP to netserver, sleep 1.2, and SIGCONT.
Rate limited to 845kbps, for visibility. Capture done at netserver side.
Previously:
01.500751 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632372996] [a_rwnd 99153] [
01.500752 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632372997] [SID: 0] [SS
01.517471 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373010] [SID: 0] [SS
01.517483 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632373009] [a_rwnd 0] [#gap
01.517485 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373083] [SID: 0] [SS
01.517488 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632373009] [a_rwnd 0] [#gap
01.534168 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373096] [SID: 0] [SS
01.534180 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632373009] [a_rwnd 0] [#gap
01.534181 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373169] [SID: 0] [SS
01.534185 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632373009] [a_rwnd 0] [#gap
02.525978 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373010] [SID: 0] [SS
02.526021 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632373009] [a_rwnd 0] [#gap
(window update missed)
04.573807 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373010] [SID: 0] [SS
04.779370 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632373082] [a_rwnd 859] [#g
04.789162 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373083] [SID: 0] [SS
04.789323 IP A.36925 > B.48277: sctp (1) [DATA] (B)(E) [TSN: 632373156] [SID: 0] [SS
04.789372 IP B.48277 > A.36925: sctp (1) [SACK] [cum ack 632373228] [a_rwnd 786] [#g
After:
02.568957 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098728] [a_rwnd 99153]
02.568961 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098729] [SID: 0] [S
02.585631 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098742] [SID: 0] [S
02.585666 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 0] [#ga
02.585671 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098815] [SID: 0] [S
02.585683 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 0] [#ga
02.602330 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098828] [SID: 0] [S
02.602359 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 0] [#ga
02.602363 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098901] [SID: 0] [S
02.602372 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 0] [#ga
03.600788 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098742] [SID: 0] [S
03.600830 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 0] [#ga
03.619455 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 13508]
03.619479 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 27017]
03.619497 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 40526]
03.619516 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 54035]
03.619533 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 67544]
03.619552 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 81053]
03.619570 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098741] [a_rwnd 94562]
(following data transmission triggered by window updates above)
03.633504 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098742] [SID: 0] [S
03.836445 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098814] [a_rwnd 100000]
03.843125 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098815] [SID: 0] [S
03.843285 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098888] [SID: 0] [S
03.843345 IP B.50536 > A.55173: sctp (1) [SACK] [cum ack 2490098960] [a_rwnd 99894]
03.856546 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490098961] [SID: 0] [S
03.866450 IP A.55173 > B.50536: sctp (1) [DATA] (B)(E) [TSN: 2490099011] [SID: 0] [S
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's possible that we receive a packet that is larger than current
window. If it's the first packet in this way, it will cause it to
increase rwnd_over. Then, if we receive another data chunk (specially as
SCTP allows you to have one data chunk in flight even during 0 window),
rwnd_over will be overwritten instead of added to.
In the long run, this could cause the window to grow bigger than its
initial size, as rwnd_over would be charged only for the last received
data chunk while the code will try open the window for all packets that
were received and had its value in rwnd_over overwritten. This, then,
can lead to the worsening of payload/buffer ratio and cause rwnd_press
to kick in more often.
The fix is to sum it too, same as is done for rwnd_press, so that if we
receive 3 chunks after closing the window, we still have to release that
same amount before re-opening it.
Log snippet from sctp_test exhibiting the issue:
[ 146.209232] sctp: sctp_assoc_rwnd_decrease: asoc:ffff88013928e000
rwnd decreased by 1 to (0, 1, 114221)
[ 146.209232] sctp: sctp_assoc_rwnd_decrease:
association:ffff88013928e000 has asoc->rwnd:0, asoc->rwnd_over:1!
[ 146.209232] sctp: sctp_assoc_rwnd_decrease: asoc:ffff88013928e000
rwnd decreased by 1 to (0, 1, 114221)
[ 146.209232] sctp: sctp_assoc_rwnd_decrease:
association:ffff88013928e000 has asoc->rwnd:0, asoc->rwnd_over:1!
[ 146.209232] sctp: sctp_assoc_rwnd_decrease: asoc:ffff88013928e000
rwnd decreased by 1 to (0, 1, 114221)
[ 146.209232] sctp: sctp_assoc_rwnd_decrease:
association:ffff88013928e000 has asoc->rwnd:0, asoc->rwnd_over:1!
[ 146.209232] sctp: sctp_assoc_rwnd_decrease: asoc:ffff88013928e000
rwnd decreased by 1 to (0, 1, 114221)
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
neigh_cleanup_and_release() is always called after marking a neighbour
as dead, but it only notifies user space and not in-kernel listeners of
the netevent notification chain.
This can cause multiple problems. In my specific use case, it causes the
listener (a switch driver capable of L3 offloads) to believe a neighbour
entry is still valid, and is thus erroneously kept in the device's
table.
Fix that by sending a netevent after marking the neighbour as dead.
Fixes: a6bf9e933daf ("mlxsw: spectrum_router: Offload neighbours based on NUD state change")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By setting certain socket options on ipv6 raw sockets, we can confuse the
length calculation in rawv6_push_pending_frames triggering a BUG_ON.
RIP: 0010:[<ffffffff817c6390>] [<ffffffff817c6390>] rawv6_sendmsg+0xc30/0xc40
RSP: 0018:ffff881f6c4a7c18 EFLAGS: 00010282
RAX: 00000000fffffff2 RBX: ffff881f6c681680 RCX: 0000000000000002
RDX: ffff881f6c4a7cf8 RSI: 0000000000000030 RDI: ffff881fed0f6a00
RBP: ffff881f6c4a7da8 R08: 0000000000000000 R09: 0000000000000009
R10: ffff881fed0f6a00 R11: 0000000000000009 R12: 0000000000000030
R13: ffff881fed0f6a00 R14: ffff881fee39ba00 R15: ffff881fefa93a80
Call Trace:
[<ffffffff8118ba23>] ? unmap_page_range+0x693/0x830
[<ffffffff81772697>] inet_sendmsg+0x67/0xa0
[<ffffffff816d93f8>] sock_sendmsg+0x38/0x50
[<ffffffff816d982f>] SYSC_sendto+0xef/0x170
[<ffffffff816da27e>] SyS_sendto+0xe/0x10
[<ffffffff81002910>] do_syscall_64+0x50/0xa0
[<ffffffff817f7cbc>] entry_SYSCALL64_slow_path+0x25/0x25
Handle by jumping to the failure path if skb_copy_bits gets an EFAULT.
Reproducer:
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
#include <sys/types.h>
#include <sys/socket.h>
#include <netinet/in.h>
#define LEN 504
int main(int argc, char* argv[])
{
int fd;
int zero = 0;
char buf[LEN];
memset(buf, 0, LEN);
fd = socket(AF_INET6, SOCK_RAW, 7);
setsockopt(fd, SOL_IPV6, IPV6_CHECKSUM, &zero, 4);
setsockopt(fd, SOL_IPV6, IPV6_DSTOPTS, &buf, LEN);
sendto(fd, buf, 1, 0, (struct sockaddr *) buf, 110);
}
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Socket cmsg IP(V6)_RECVORIGDSTADDR checks that port range lies within
the packet. For sockets that have transport headers pulled, transport
offset can be negative. Use signed comparison to avoid overflow.
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Reported-by: Nisar Jagabar <njagabar@cloudmark.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When matching on flags, we should require the user to provide the
mask and avoid using an all-ones mask. Not doing so causes matching
on flags provided w.o mask to hit on the value being unset for all
flags, which may not what the user wanted to happen.
Fixes: faa3ffce7829 ('net/sched: cls_flower: Add support for matching on flags')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UDP dst port was provided to the helper function which sets the
IPv6 IP tunnel meta-data under a wrong param order, fix that.
Fixes: 75bfbca01e48 ('net/sched: act_tunnel_key: Add UDP dst port option')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e2d118a1cb5e ("net: inet: Support UID-based routing in IP
protocols.") made ip_do_redirect call sock_net(sk) to determine
the network namespace of the passed-in socket. This crashes if sk
is NULL.
Fix this by getting the network namespace from the skb instead.
Fixes: e2d118a1cb5e ("net: inet: Support UID-based routing in IP protocols.")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Madalin reported crashes happening in tcp_tasklet_func() on powerpc64
Before TSQ_QUEUED bit is cleared, we must ensure the changes done
by list_del(&tp->tsq_node); are committed to memory, otherwise
corruption might happen, as an other cpu could catch TSQ_QUEUED
clearance too soon.
We can notice that old kernels were immune to this bug, because
TSQ_QUEUED was cleared after a bh_lock_sock(sk)/bh_unlock_sock(sk)
section, but they could have missed a kick to write additional bytes,
when NIC interrupts for a given flow are spread to multiple cpus.
Affected TCP flows would need an incoming ACK or RTO timer to add more
packets to the pipe. So overall situation should be better now.
Fixes: b223feb9de2a ("tcp: tsq: add shortcut in tcp_tasklet_func()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Madalin Bucur <madalin.bucur@nxp.com>
Tested-by: Madalin Bucur <madalin.bucur@nxp.com>
Tested-by: Xing Lei <xing.lei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sctp.local_addr_list is a global address list that is supposed to include
all the local addresses. sctp updates this list according to NETDEV_UP/
NETDEV_DOWN notifications.
However, if multiple NICs have the same address, the global list would
have duplicate addresses. Even if for one NIC, promote secondaries in
__inet_del_ifa can also lead to accumulating duplicate addresses.
When sctp binds address 'ANY' and creates a connection, it copies all
the addresses from global list into asoc's bind addr list, which makes
sctp pack the duplicate addresses into INIT/INIT_ACK packets.
This patch is to filter the duplicate addresses when copying the addrs
from global list in sctp_copy_local_addr_list and unpacking addr_param
from cookie in sctp_raw_to_bind_addrs to asoc's bind addr list.
Note that we can't filter the duplicate addrs when global address list
gets updated, As NETDEV_DOWN event may remove an addr that still exists
in another NIC.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to reduce indent level by using continue when the addr
is not allowed, and also drop end_copy by using break.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a break statement to prevent fall-through from
OVS_KEY_ATTR_ETHERNET to OVS_KEY_ATTR_TUNNEL. Without the break
actions setting ethernet addresses fail to validate with log messages
complaining about invalid tunnel attributes.
Fixes: 0a6410fbde ("openvswitch: netlink: support L3 packets")
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__ip_append_data and ip_finish_output
There is an inconsistent conditional judgement in __ip_append_data and
ip_finish_output functions, the variable length in __ip_append_data just
include the length of application's payload and udp header, don't include
the length of ip header, but in ip_finish_output use
(skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ip header.
That causes some particular application's udp payload whose length is
between (MTU - IP Header) and MTU were fragmented by ip_fragment even
though the rst->dev support UFO feature.
Add the length of ip header to length in __ip_append_data to keep
consistent conditional judgement as ip_finish_output for ip fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three fixes:
* avoid a WARN_ON() when trying to use WEP with AP_VLANs
* ensure enough headroom on mesh forwarding packets
* don't report unknown/invalid rates to userspace
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The protocol field is checked when deleting IPv4 routes, but ignored for
IPv6, which causes problems with routing daemons accidentally deleting
externally set routes (observed by multiple bird6 users).
This can be verified using `ip -6 route del <prefix> proto something`.
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a warning for drivers to use when encountering an invalid
buffer for XDP. For normal cases this should not happen but to catch
this in virtual/qemu setups that I may not have expected from the
emulation layer having a standard warning is useful.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
null
Prior to this patch, sctp_transport_lookup_process didn't rcu_read_unlock
when it failed to find a transport by sctp_addrs_lookup_transport.
This patch is to fix it by moving up rcu_read_unlock right before checking
transport and also to remove the out path.
Fixes: 1cceda784980 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 7fda702f9315 ("sctp: use new rhlist interface on sctp transport
rhashtable"), sctp has changed to use rhlist_lookup to look up transport, but
rhlist_lookup doesn't call rcu_read_lock inside, unlike rhashtable_lookup_fast.
It is called in sctp_epaddr_lookup_transport and sctp_addrs_lookup_transport.
sctp_addrs_lookup_transport is always in the protection of rcu_read_lock(),
as __sctp_lookup_association is called in rx path or sctp_lookup_association
which are in the protection of rcu_read_lock() already.
But sctp_epaddr_lookup_transport is called by sctp_endpoint_lookup_assoc, it
doesn't call rcu_read_lock, which may cause "suspicious rcu_dereference_check
usage' in __rhashtable_lookup.
This patch is to fix it by adding rcu_read_lock in sctp_endpoint_lookup_assoc
before calling sctp_epaddr_lookup_transport.
Fixes: 7fda702f9315 ("sctp: use new rhlist interface on sctp transport rhashtable")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
